Officejet 6000 ink

Similar Questions

• Don't print black ink (HP Officejet 6000 E609a Series)

  HP Officejet 6000 E609a Series - do not black ink print ---
  No warning light indicates low ink levels, so I called "solutions Center". The chart shows all cartridges, color and black to be virtually complete. I then replace the black cartridge with a new cartridge 920XL, thinking that the original could be defective. Same as before results! I (1) printed to a printer status report (2) print a print quality diagnostics page, (3) aligned the print heads and (4) cleaned the print heads, all to nothing does not. I even carefully cleaned the container for the black cartridge with a Q-Tip to collect a small amount of excess ink. Color cartridges are printing very well but the black cartridges will not print. (Either by the way, it seemed to happen suddenly, not gradually). I would be sincerely acknowledging all recommendations to solve this problem.
  Thank you... RP

  @ wespikard - here is a link to a document that addresses print quality problems of the model of printer that is mentioned in the first post of this thread. It will give you instructions to solutions that will attempt to correct the output quality of your printer. I hope this helps.

• Cartridge, HP 920 XL: Wireless HP Officejet 6000, the problem of black ink printer

  I have a HP Officejet 6000 wireless printer.  It's 2nd HP 920 XL cartridge that has not worked.  It does not show that it is empty, but it will not be printed.  Our school cannot afford to replace these at this rate.  Please let me know what to do to make this work correctly.

  I removed the printer as my default so that I could use another printer.  When I ran the program again to check for problems, the guest asked me to add the printer returned as default.   When I reconnected it the printer as long as my default, I tested the printer and it worked.  Don't know why remove and then add back in the set, but he did.

• OfficeJet 6000: OfficeJet 6000 does not print

  Replace the ink cartridges for Officejet 6000 would not print.  It prints the words Page Windows printer to test a test page of color with a printer icon in the upper right, then at the center of page 4 with a white fill boxes; yellow fill, blue fill and a red fill.  That's all.  I touched a "print test page" and the paper comes out blank, although that normally shake it like the print head moves back.

  Hello @Pistol_shooter, greetings!

  Thank you access the Forums from HP Support for extra support! I see that you are having problems printing using the Officejet 6000. I will do my best to help you with this problem.

  I suggest you first check the empty ink to ensure it is enough ink. Then proceed to clean the print head using the software installed on your computer. Since your computer desktop, double-click the printer icon, the printer wizard / solution Center will open. Go to settings and navigate to the cleaning of the printheads.

  I found a wonderful document that gives you instructions step by step to solve this problem. Please visit: http://hp.care/2dtFaXe

  Please let me know if that solves the problem. Good luck!

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• HP Officejet 6000 609(a): Officejet 6000

  I now want to use this printer for black and white text only. This 920 cartridge needs to be replaced and all colour cartridges show as empty.  I didn't print in gray scale and do not use colors for awhile. Can I just replace this cartridge black & white and forget the colors? as these are expensive to replace, and I'm not going to use them?  I don't want to make this investment in color if possible with this printer Officejet 6000 609(a).  Thanks for the tips!

  I just bought the Multipack cartridges at great expense... but just for a test before it is replaced, I printed a Test Page.  The old B & W ink cartridge works perfectly, although the colors were very thirsty (I don't need them anyway).   It is a strange behavior, like the last time that the printer has been tried on a document, the results were so washed out as unreadable.

  So, "if it ain't broke, don't fix it" applies to me.  Moral: my printer will get the long OK until it is absolutely out of B & W. Then all of the cartridges will be replaced if necessary.  The box has a long service life ).

• HP Officejet 6000 a: after far right stuck paper jam

  HP Officejet 6000 a and Windows 10.

  After jam paper and jam, clearing printer turn on, goes through current transport parks, start right, flashing lites power and resume. Doctor says print "general Printer Error. Transport to open the lid does not come to Center and did not manually move parked at the far right. Close the cover, flashing lites power and resume, press summary and unplug the power cord when the cart is centered. Remove print head, close the lid, back the start-up routine. Open the lid and now transport stops in the Center and all the lites normals. With lamp torch and lid open (with cardboard in photo electric switch) and print head installed in position, pressing on the set of the view CV under presses of subsequent print head print head to prevent fresh ink while the printer is in sleep mode, remove the cardboard (lid open simulating) tray does not move downwards releasing the print head. Has gone through all six steps of the Solution and no help. Impossible to open the case to observe the load mechanism. Nothing else to try? Printer purchased January 2011 and printed only 5003 + pages and no problems so far. Do not throw with using more than that most just bought full set XL HP 920HP cartridges. should be possible to solve other than maintenance workshop, can buy nine being the least expensive.

  Help, please. Thank you

  Jesse

  Hi @jlmulanax1,

  Welcome to the Forums of HP Support!

  I understand that this transport on your HP Officejet 6000 a printer does not move correctly. I will definitely do my best to help you.

  I would try the steps in Th guides, r HP Officejet 6000 (E609) and 7000 (E809) Wide Format Printer Series - an "impossible cartridge" or "incompatible cartridge" Message is displayed on the calculationand lights flashing on the HP Officejet 6000 (E609a) and 6000 (E609n) wireless printers.

  You describe it sounds like the transport has stalls and if this is the case and you are unable to find the obstruction while the transport mechanism is defective.

  If you have completed all the above steps and your product still has a problem, service the product.

  Contact HP for service in all countries except Asia-Pacific.

  First, check your product warranty to check your warranty printer status and then go to contact HP support to find an authorized dealer or to schedule a repair.
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number are displayed.

  Hope that answers your question. Thank you for posting!

• HP officejet 6000: officejet e609a software

  Hi friends

  I'm at my wits end, I tried to install the software for the officejet 6000 E609a for two days. I continue to receive updates of pilot who want me to pay. I buy a printer of opportunity that I had loads of ink for this one and my laptop has broken with the software on it and I can't find the software for this printer anywhere. Please help I'll seriously crazy I know it must be something that I just miss, but I can't find the it. Help send me a link. I'm connectioning with a key usb and printer and windows can't find the driver and I can't find the download on hp, or anywhere else. Thanks thanks thanks a lot in advance

  Morag

  Hi @momogallas,

  Welcome to the HP Forums!

  I see that you are looking for the software and drivers for your printer HP Officejet 6000 e609a for Windows Vista to. I'm happy to meet you!

  To download the full feature software and driver, please visit this Web site, software HP Officejet full feature and pilot.

  This guide, the Message "Device not found" is displayed in Windows XP or Windows Vista during the Installation of USB, could help if you get stuck at all.

  Hope this is what you are looking for and have a great day!

• Officejet 6000 printing problems

  My Officejet 6000 will not print. The power and light of the resume light blink - normally, this means that there is a paper jam in which there is not. Or that the rollers need cleaning I did. I also cleaned the cartridges where the ink comes out.

  Also I tried to unplug the printer and try again without success. When the power is connected, the green light - after a few seconds it starts to blink and the printer goes into his routine of cleaning after this stop the Summary button illuminates and flashes also. I'd love to hear if someone has the same situation and managed to solve it!

  Have you removed all paper from the input tray and look in the status bar with a flashlight to make sure nothing is caught in the rollers?

  So, did you remove the module front/back/rear access door to make sure that nothing is stuck to the back of the rolls?

  I also advise to open the upper part of the printer and remove all of the ink provides unit; including the print head.  Don't you see that anything taken under/the print head Assembly all about?

  Hard reset of the printer with the supplies out of the unit:

  Unplug the unit when turned on

  Disconnect the other end of the power cord from the wall jack directly

  * Wait 30 seconds

  * Plug the unit back to

  Once the device is fed up reinstall ink supplies in the printer.  Also check to see if the truck can slide left and right all the way inside the printer by hand.

  There is also a document with additional steps found here.  I hope this helps.

• HP Officejet 6000 Print gray instead of black

  Hello

  My HP Officejet 6000 works well for about a year until today, where he began to print light gray instead of black.

  My officejet is attached via USB directly to my PC, I'm under Ubuntu 12.04 with gnome shell. Used to work out of the area to print. I just install HPLIP Toolbox to see if I can fix anything, but that was no help. I exchanged the inktank black for a new, but that did not help either one. The gray looks perfect gray and not a faded defective, black dryness. I tried to change the output of color mode in the settings of the printer to the only black than gray, and the printer does not print the necessary ink at all. Is this a software problem? Or printer hardware problem? I tried printing from my laptop and had the same problem.

  Any help would be appreciated.

  Problem solved. I got my printer to my friend who has a Windows PC and a test print looked fine. I thought it must be a Linux question then. I have connected my printer to my PC Ubuntu again, and for the hell of it, I tried to print a test page and go figure, it worked. Maybe unplug the printer helped solve the problem? BTW, when I meet my problem, the printer was not actually printing gray instead of black by mixing the inktanks color. I discovered that she did not use the black tank at all. I'm glad that everything works again without having to really fix anything. So if anyone else has this problem, try disconnecting the printer, and then try again. That could be the solution. Turn off the PC one on or the printer doesn't help.

• HP Officejet 6000

  Use a model HP Officejet 6000 E609a - problem is not print: have cleaned the printer head and put on the new cartridges but still will not print.  None of the lights are flashing.  Having run out of options.  What could be the probel?  Is there anything else that could be done?  Thank you.

  Hi batch64,

  Welcome to the HP Forums!

  I see that your HP Officejet 6000 will not print. I'm happy to help with this problem!

  To get help, I'll need to know:

  1. If you use Windows or operating system Mac and the version number. To find the exact version, visit this link. Whatsmyos.
  2. If the printer can print a self-test report. Print a printer status report.
  3. If the printer is connected, wireless, or USB.
  4. If the power cable is connected to a surge protector, or directly to a wall outlet. Questions when it is connected to an uninterruptible power supply/Strip/surge protector power. This is true for printers and ink jet.

  I hope to hear from you and have a great day!

• Windows 8 - officejet 6000 - just stopped printing black-

  Windows 8 - officejet 6000 - just stopped printing black-

  put a new black cartridge in and now it will not print black - going to test the page and color printing - can hardly see black text on the test page - gray value - has always been - no other changes have had recourse to the same printer for a little over a year.  Only clean the print heads still no black printing.

  Hi rea123,

  I understand that you have an Officejet 6000, which is currently not print black ink. I'm sorry to hear what is happening, but I will do my best to help you.

  I suggest that you first look through this document for Troubleshooting print quality problems because it may be a few steps that you have not yet tried.  This document 'Print head problem' or "Print head seems to be missing or corrupt" Message appears on the computer has also a few steps to know how to clean the print head manually.

  If all else fails, take a look at the Bob_Headrick station for soaking your printhead.

  Hope this helps, have a nice day!

• OfficeJet 6000: service station

  I have an officejet 6000 needed the cleaned gas station. Any one know how to down the hood so I can get to it. ink from the printer works fine, it's just that when the printhead is parked for a period of time, it leaves bloches and I have to remove the print head for cleaning.

  cordially V. Presta

  Here is the link to the site that showed me how tell - assemble an officejet 6000, so that I could clean the service station. The site is Korean but I don't need a comment that the vid is very detailed.

  http://www.YouTube.com/watch?v=RmjuHg3Z8-U

  vmpresta

• OfficeJet 6000 periodic Type misaligned

  My new Officejet 6000 was a periodic problem that I was unable to trouble. In any body of text of type I, there are periodic letters fussing in the words or phrases. With other printers that I've had, the problem was still attached by aligning or cleaning of the printheads. This time nothing I've done has fixed this annoying problem. What should I try?

  Thanks, Pontus, for your quick response! In the past, with other printers, I kept the black ink using the "quick/fast/economical printing project" and never recall seen periodic misaligned type that has not been corrected with the direction of the print head. I use a better quality (not often), of course, when I want good copies as some press reports. But your suggestion worked when I used "General daily Impression" / "Normal" / "Print in grayscale" / "black ink only." Since I want to continue to use a minimum of black ink, I assume that 'Fast draft mode' will be my choice for this copy as e-mail. Thanks again for your helpful answer!

• OfficeJet 6000: Officejet 6000 'stuck' in the wireless status

  After using the printer on a minitour HP with a USB connection for a while, I installed the software on a Thinkpad with a link wireless to a Linksys router. The combination didn't work reliably, so I removed the printer and the laptop software. However, the Officejet seems 'stuck' in a State wireless (blue light on); When I tried a clean reinstall on the minitour (from disk), the installation failed. How can I restore the printer to its out-of-the-box condition and get a clean install with USB connection?

  (I thought the Officejet 6000 is a dual-mode device, but it seems to be either / or machine.)

  Price Buhrman

  Hi BuhrmanP,

  This is the only information available for this model restore network settings.

  This information was given by the manual, page 377. OFFICEJET 6000

  

  I disable all startup programs and temporarily disable the Antivirus software before installing the printer to see if it will help.

  How to perform a clean boot in Windows.

  I hope this helps.

  Thank you.

• HP OfficeJet 6000 Wireless: can I use AirPrint on a wireless HP OfficeJet 6000, model C9295A

  My iPad can not find my HP OfficeJet 6000 wireless, try using AirPrint. This printer can use the AirPrint? I have to update to firmware maybe?

  Hello

  Your printer is not on the following list:

  https://support.Apple.com/en-AU/HT201311

  and not in the following list:

  http://support.HP.com/us-en/document/c02814760#N4001

  You can try:

  http://iTunes.Apple.com/au/app/HP-eprint/id299531647?Mt=8

  Good luck.