Only way ASA Vpn access

Similar Questions

• When I click on a link in an e-mail, I get the message following 'application not found. The only way I can access the site is to copy the link, but it is not always possible

  When I click on a link in an e-mail, I get the message following 'application not found. The only way I can access the site is to copy the link, but it is not always possible. Can you advise?

  Hello

  Follow these steps to solve the problem.

  
  Step 1
  a. Click Start, default programs
  b. Click set your default programs
  c. Select your browser from the list
  d. Click set this program as default
  e. click OK.

  Then proceed as follows:

  
  Step 2
  a. click settings by default access and computer program Set
  b. click on continue if you see the user account control prompt.
  c. click Customize
  d. Select your browser from the list
  e. click OK.

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• ASDM conc (ASA) VPN access

  I have the script like this:

  an ASA, which is the FW, TR making static NAT from the public to the private IP and private IP address add is add conc (another ASA) VPN. I am accessing these devices via the VPN client and I get the address IP of VPN pool set on VPN conc. VPN conc. is in a DMZ VLAN, but it also has connection to the local network segment. Purposes of mgmt, I connect to this VPN through SSH conc via a switch in the local network segment. To use the http access, I have to be on one of the servers that are in the local network segment. Since then, when I set up the VPN connection, I'm sure VPN conc., what can do to access http directly from my PC?

  This sets up on the conc VPN:

  management-access inside
  
  After that you should be able to use ASDM over the VPN tunnel, by connecting to its inside ip address.
  hth
  
      Herbert
  
      (note, I assume the name of the interface connected to the LAN is named "inside", if not adapt at will )

• 8.3 ASA VPN access rules

  Hi, I recently bought an ASA 5520 to use as a VPN gateway for several tunnells site to site VPN. I've upgraded to version 8.3, and set up a lab environment. I implemented a simple VPN with a rule of intellectual property general permit to stert with and everything works fine. I'm having trouble tightenign access now, if I change the access on the SAA for ICMP I can ping both directions, if I add tcp I can telnet from a computer at the other end of the VPN, but if I change the tcp protocol to telnet, I can't connect. the other end on the VPN is a cisco 2620XM and I match the lists of access for each of the changes. I also do not understand the meaning of the ASA access list, it seems that if I want to allow the remote tcp host behind the ASA access I have the host behind the ASA as the source, it appears backward? Anyone can shed some light on this? very much appreciated.

  Yes, you are supposed to only configure 'IP' to your ACL (ACL applied to your crypto card) crypto and crypto ACL supposed to mirror image on each peer, so when you change to specific TCP/UDP ports, is not mirror image of the other side/peer more.

  I thought that you use ACL applied to "vpn-filter".

  But in the previous post, actually configure you ACL on each interface.

  The above is 3 different ACL you have applied differently (crypto ACL--> apply to the card crypto, vpn ACL--> apply to vpn-filter and your normal ACL interface).

• interrupted vistas system restore and now it does not start at the top. The only way I can access advanced boot options is by pressing F8

  Then I tried to start Windows normally or in Mode safe and it does not work.

  None of these advanced startup options work effectively.

  When I turn on the laptop, the VAIO large appears and then Microsoft corporation and then a quick start of blue, then it tries to restart again again and again until I hit F8.

  I hope this can be repaired.  Thanks in advance for anyones help.

  Hello

  as none of the advanced startup options does work, try this:

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Traffic permitted only one-way for VPN-connected computers

  Hello

  I currently have an ASA 5505.  I put up as a remote SSL VPN access. My computers can connect to the VPN very well.  They just cannot access the internal network (192.168.250.0).  They cannot ping the inside interface of the ASA, nor any of the machines.  It seems that all traffic is blocked for them.  The strange thing is that when someone is connected to the VPN, I can ping this ASA VPN connection machine and other machines inside the LAN.  It seems that the traffic allows only one way.  I messed up with ACL with nothing doesn't.  Any suggestions please?

  Pool DHCP-192.168.250.20 - 50--> for LAN

  Pool VPN: 192.168.250.100 and 192.168.250.101

  Outside interface to get the modem DHCP

  The inside interface: 192.168.1.1

  Courses Running Config:

  : Saved

  :

  ASA Version 8.2 (5)

  !

  hostname HardmanASA

  activate the password # encrypted

  passwd # encrypted

  names of

  !

  interface Ethernet0/0

  switchport access vlan 20

  !

  interface Ethernet0/1

  switchport access vlan 10

  !

  interface Ethernet0/2

  switchport access vlan 10

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  switchport access vlan 10

  !

  interface Vlan1

  No nameif

  no level of security

  no ip address

  !

  interface Vlan10

  nameif inside

  security-level 100

  IP 192.168.250.1 255.255.255.0

  !

  interface Vlan20

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  mask 192.168.250.100 - 192.168.250.101 255.255.255.0 IP local pool VPN_Pool

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 10 192.168.250.0 255.255.255.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.250.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet timeout 5

  SSH 192.168.250.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  Console timeout 0

  dhcpd dns 8.8.8.8

  !

  dhcpd address 192.168.250.20 - 192.168.250.50 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image

  Picture disk0:/anyconnect-linux-2.5.2014-k9.pkg 3 SVC

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  value of server DNS 8.8.8.8

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address pool VPN_Pool

  tunnel-group AnyConnect webvpn-attributes

  enable AnyConnect group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:30fadff4b400e42e73e17167828e046f

  : end

  Hello

  No worries

  As we change the config I would do as well as possible.

  First, it is strongly recommended to use a different range of IP addresses for VPN clients and the internal network

  No VPN_Pool 192.168.250.100 - 192.168.250.101 255.255.255.0 ip local pool mask

  mask 192.168.251.100 - 192.168.251.101 255.255.255.0 IP local pool VPN_Pool

  NAT_0 ip 192.168.250.0 access list allow 255.255.255.0 192.168.251.0 255.255.255.0

  NAT (inside) 0-list of access NAT_0

  Then give it a try and it work note this post hehe

• Unable to connect to other remote access (ASA) VPN clients

  Hello

  I have a cisco ASA 5510 appliance configured with remote VPN access

  I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

  For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

  Any help is welcome.

  Thanks in advance.

  Hello

  I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

  It seems to me that you currently have dynamic PAT configured for the VPN users you have this

  NAT (outside) 1 10.40.170.0 255.255.255.0

  If your traffic is probably corresponding to it.

  The only thing I can think of at the moment would be to configure

  Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

  list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

  NAT (outside) 0-list of access VPN-CLIENT-NAT0

  I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

  -Jouni

• Remote access ASA, VPN and NAT

  Hello

  I try to get access to remote VPN work using a Cisco VPN client and ASA with no split tunneling. The VPN works a little, I can access devices inside when I connect, but I can't access the Internet. I don't see any errors in the log ASA except these:

  1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/137 dst outside:192.168.47.255/137
  1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/54918 dst outsidexx.xxx.xxx.xxx/53

  There is only one address public IP that is assigned to the external interface of DHCP. The Interior is 192.168.1.0/24 network which is PAT'ed to the external interface and the VPN network is 192.168.47.X.

  I think my problem is that the net.47 is not NAT'ed out properly and I don't know how to put in place exactly. I can't understand how this is supposed to work since the net VPN technically provenance from the outside already.

  Here are all the relevant config:

  list of vpn access extended permits all ip 192.168.47.0 255.255.255.0
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool vpnpool 192.168.47.200 - 192.168.47.220 mask 255.255.255.0
  IP verify reverse path to the outside interface
  IP audit info alarm drop action
  IP audit attack alarm drop action
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow all outside
  Global interface (2 inside)
  Global 1 interface (outside)
  NAT (inside) 0-list of access vpn
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 2 192.168.47.0 255.255.255.0 outside
  static (inside, outside) tcp 3074 XBOX360 3074 netmask 255.255.255.255 interface
  static (inside, outside) udp 3074 XBOX360 3074 netmask 255.255.255.255 interface
  public static (inside, outside) udp interface 88 88 XBOX360 netmask 255.255.255.255
  public static tcp (indoor, outdoor) https someids netmask 255.255.255.255 https interface

  I can post more of the configuration if necessary.

  Change ' nat (outside) 2 192.168.47.0 255.255.255.0 apart ' "NAT (2-list of vpn access outdoors outside)" gives these:

  1 Jul 06:18:35 % gatekeeper ASA-3-305005: no group of translation not found for udp src outside:192.168.47.200/56003 dst outside:66.174.95.44/53

  So, how I do right NAT VPN traffic so it can access the Internet?

  A few things that needs to be changed:

  (1) NAT exemption what ACL must be modified to be more specific while the traffic between the internal subnets and subnet pool vpn is not coordinated. NAT exemption takes precedence over all other statements of NAT, so your internet traffic from the vpn does not work.

  This ACL:

  list of vpn access extended permits all ip 192.168.47.0 255.255.255.0

  Should be changed to:

  extensive list of access vpn ip 192.168.47.0 255.255.255.0 allow

  (2) you don't need statement "overall (inside) 2. Here's what to be configured:

  no nat (outside) 2 192.168.47.0 255.255.255.0 outside

  no global interface (2 inside)

  NAT (outside) 1 192.168.47.0 255.255.255.0

  (3) and finally, you must activate the following allow traffic back on the external interface:

  permit same-security-traffic intra-interface

  And don't forget to clear xlate after the changes described above and connect to your VPN.

  Hope that helps.

• Remote RDP client VPN access on ASA 5510

  Hello.

  We have configured the VPN tunnel from site of offshore to the location of the customer using ASA5510 and access to RDP to the location of the customer. Also been configured remote VPN access in offshore location. But using the remote VPN client, we are able to get the RDP of officeshore location but not able to access to the location of the RDP client. Are there any additional changes required?

  Thank you

  Hi Salsrinivas,

  so to summarize:

  the VPN client connects to the ASA offshore

  the VPN client can successfully RDP on a server at the offshore location

  the VPN client cannot NOT RDP on a server at the location of the customer

  offshore and the location of the customer are connected by a tunnel L2L

  (and between the 2 sites RDP works very well)

  is that correct?

  Things to check:

  -the vpn in the ACL crypto pool?

  -you're exemption nat for traffic between the vpn pool and 'customer' LAN? is the exemption outside (vpn clients are coming from the outside)?

  -you have "same-security-traffic permitted intra-interface" enabled (traffic will appear outside and go back outside)?

  If you need help more could you put a config (sterilized) Please?

  HTH
  Herbert

• ASA 5505: VPN access to different subnets

  Hi All-

  I'm trying to understand how to configure our ASA so that remote users can have VPN access to two different subnets (Office LAN and LAN phone).  Currently I have 3 VLAN configuration - VLAN 1 (inside), VLAN 2 (outside), VLAN 13 (phone LAN).  Essentially, remote users must be able to access their PC (192.168.1.0/24) and also have access to the office phone system (192.168.254.0/24).  Is it still possible?  Here are the configurations on our ASA,

  Thanks in advance:

  ASA Version 8.2 (5)

  !

  names of

  name 10.0.1.0 Net-10

  name 20.0.1.0 Net-20

  name phone 192.168.254.0

  name 192.168.254.250 PBX

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  switchport access vlan 3

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 13

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.1.98 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP X.X.139.79 255.255.255.224

  !

  interface Vlan3

  No nameif

  security-level 50

  192.168.5.1 IP address 255.255.255.0

  !

  interface Vlan13

  nameif phones

  security-level 100

  192.168.254.200 IP address 255.255.255.0

  !

  passive FTP mode

  object-group service RDP - tcp

  EQ port 3389 object

  object-group service DM_INLINE_SERVICE_1

  the purpose of the ip service

  EQ-ssh tcp service object

  vpn_nat_inside of access list extensive ip Net-10 255.255.255.224 allow 192.168.1.0 255.255.255.0

  access-list extended vpn_nat_inside allowed ip Net-10 255.255.255.224 phones 255.255.255.0

  inside_nat0_outbound list extended access permits all ip Net-10 255.255.255.224

  inside_access_in of access allowed any ip an extended list

  Split_Tunnel_List list standard access allowed Net-10 255.255.255.224

  phones_nat0_outbound list extended access permits all ip Net-10 255.255.255.224

  outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 Mac host everything

  pager lines 24

  Enable logging

  timestamp of the record

  record monitor errors

  record of the mistakes of history

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 phones

  mask IP local pool SSLClientPool-10 10.0.1.1 - 10.0.1.20 255.255.255.128

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global interface (10 Interior)

  Global 1 interface (outside)

  global interface (phones) 20

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (10 vpn_nat_inside list of outdoor outdoor access)

  NAT (phones) 0-list of access phones_nat0_outbound

  NAT (phones) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 X.X.139.65 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication enable LOCAL console

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = not - asa .null

  pasvpnkey key pair

  Configure CRL

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  lifetime 28800

  VPN-sessiondb max-session-limit 10

  Telnet timeout 5

  SSH 192.168.1.100 255.255.255.255 inside

  SSH 192.168.1.0 255.255.255.0 inside

  SSH Mac 255.255.255.255 outside

  SSH timeout 60

  Console timeout 0

  dhcpd auto_config inside

  !

  dhcpd address 192.168.1.222 - 192.168.1.223 inside

  dhcpd dns 64.238.96.12 66.180.96.12 interface inside

  !

  a basic threat threat detection

  host of statistical threat detection

  Statistics-list of access threat detection

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image

  enable SVC

  tunnel-group-list activate

  internal SSLClientPolicy group strategy

  attributes of Group Policy SSLClientPolicy

  WINS server no

  value of 64.238.96.12 DNS server 66.180.96.12

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout no

  VPN-session-timeout no

  IPv6-vpn-filter no

  VPN-tunnel-Protocol svc

  group-lock value NO-SSL-VPN

  by default no

  VLAN no

  NAC settings no

  WebVPN

  SVC mtu 1200

  SVC keepalive 60

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  SVC compression no

  attributes of Group Policy DfltGrpPolicy

  value of 64.238.96.12 DNS server 66.180.96.12

  Protocol-tunnel-VPN IPSec svc webvpn

  attributes global-tunnel-group DefaultRAGroup

  address-pool SSLClientPool-10

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared key *.

  NO-SSL-VPN Tunnel-group type remote access

  General-attributes of the NO-SSL-VPN Tunnel-group

  address-pool SSLClientPool-10

  Group Policy - by default-SSLClientPolicy

  NO-SSL-VPN Tunnel - webvpn-attributes group

  enable PAS_VPN group-alias

  allow group-url https://X.X.139.79/PAS_VPN

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Hello

  Loss of connectivity to the LAN is not really supposed all remove this command UNLESS your network is using another device as their gateway to the Internet. In this case configuration dynamic PAT or political dynamics PAT (as you) would make sense because the LAN hosts would see your VPN connection from the same directly connected network users and would be know to traffic before the ASA rather than their default gateway.

  So is this just for VPN usage and NOT the gateway on the LAN?

  If it is just the VPN device I'd adding this

  global interface (phones) 10

  He would do the same translation for 'phones' as he does on 'inside' (of course with different PAT IP)

  -Jouni

• Wacky VPN access problem of ASA

  Hi people,

  I am currenty a situation, and I am in real need of advice...

  The situation is that, if ASA helps my remote branches to access my home network and its allowing people to visit Internet inside, its not allowing the remote VPN client VPN access... R V to aid VPN client version of Cisco 4.6...

  See a presentation of basic network that illustrates our network and configuration of the ASA...

  Advice to solve this problem will be greatly appreciated...

  Kind regards

  Noman Bari

  I see what rou are... Please see my attchement...

  Please rate if it helps!

• Client VPN access to VLAN native only

  I have a router 2811 (config below) with VPN set up.  I can connect through the VPN devices and access on the VLAN native but I can't access the 10.77.5.0 (VLAN 5) network (I do not access the 10.77.10.0 - network VLAN 10).  This question has been plagueing me for quite a while.  I think it's a NAT device or ACL problem, but if someone could help me I would be grateful.  Client VPN IP pool is 192.168.77.1 - 192.168.77.10.  Thanks for the research!

  Current configuration: 5490 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  2811-Edge host name

  !

  boot-start-marker

  boot-end-marker

  !

  enable secret 5 XXXX

  !

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  AAA - the id of the joint session

  !

  IP cef

  No dhcp use connected vrf ip

  DHCP excluded-address IP 10.77.5.1 10.77.5.49

  DHCP excluded-address IP 10.77.10.1 10.77.10.49

  !

  dhcp Lab-network IP pool

  import all

  Network 10.77.5.0 255.255.255.0

  router by default - 10.77.5.1

  !

  pool IP dhcp comments

  import all

  Network 10.77.10.0 255.255.255.0

  router by default - 10.77.10.1

  !

  domain IP HoogyNet.net

  inspect the IP router-traffic tcp name FW

  inspect the IP router traffic udp name FW

  inspect the IP router traffic icmp name FW

  inspect the IP dns name FW

  inspect the name FW ftp IP

  inspect the name FW tftp IP

  !

  Authenticated MultiLink bundle-name Panel

  !

  voice-card 0

  No dspfarm

  !

  session of crypto consignment

  !

  crypto ISAKMP policy 1

  BA aes 256

  preshared authentication

  Group 2

  life 7200

  !

  Configuration group customer isakmp crypto HomeVPN

  key XXXX

  HoogyNet.net field

  pool VPN_Pool

  ACL vpn

  Save-password

  Max-users 2

  Max-Connections 2

  Crypto isakmp HomeVPN profile

  match of group identity HomeVPN

  client authentication list userauthen

  ISAKMP authorization list groupauthor

  client configuration address respond

  !

  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpn

  !

  Crypto-map dynamic vpnclient 10

  Set transform-set vpn

  HomeVPN Set isakmp-profile

  market arriere-route

  !

  dynamic vpn 65535 vpnclient ipsec-isakmp crypto map

  !

  username secret privilege 15 5 XXXX XXXX

  username secret privilege 15 5 XXXX XXXX

  Archives

  The config log

  hidekeys

  !

  IP port ssh XXXX 1 rotary

  !

  interface Loopback0

  IP 172.17.1.10 255.255.255.248

  !

  interface FastEthernet0/0

  DHCP IP address

  IP access-group ENTERING

  NAT outside IP

  inspect the FW on IP

  no ip virtual-reassembly

  automatic duplex

  automatic speed

  No cdp enable

  vpn crypto card

  !

  interface FastEthernet0/1

  no ip address

  automatic duplex

  automatic speed

  No cdp enable

  !

  interface FastEthernet0/1.1

  encapsulation dot1Q 1 native

  IP 10.77.1.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  interface FastEthernet0/1.5

  encapsulation dot1Q 5

  IP 10.77.5.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  interface FastEthernet0/1.10

  encapsulation dot1Q 10

  IP 10.77.10.1 255.255.255.0

  IP access-group 100 to

  IP nat inside

  IP virtual-reassembly

  !

  interface FastEthernet0/0/0

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1/0

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  router RIP

  version 2

  10.0.0.0 network

  network 172.17.0.0

  network 192.168.77.0

  No Auto-resume

  !

  IP pool local VPN_Pool 192.168.77.1 192.168.77.10

  no ip forward-Protocol nd

  !

  IP http server

  no ip http secure server

  overload of IP nat inside source list NAT interface FastEthernet0/0

  !

  IP extended INBOUND access list

  permit tcp any any eq 2277 newspaper

  permit any any icmp echo response

  allow all all unreachable icmp

  allow icmp all once exceed

  allow tcp any a Workbench

  allow udp any any eq isakmp

  permit any any eq non500-isakmp udp

  allow an esp

  allowed UDP any eq field all

  allow udp any eq bootps any eq bootpc

  NAT extended IP access list

  IP 10.77.5.0 allow 0.0.0.255 any

  IP 10.77.10.0 allow 0.0.0.255 any

  IP 192.168.77.0 allow 0.0.0.255 any

  list of IP - vpn access scope

  IP 10.77.1.0 allow 0.0.0.255 192.168.77.0 0.0.0.255

  IP 10.77.5.0 allow 0.0.0.255 192.168.77.0 0.0.0.255

  !

  access-list 100 permit udp any eq bootpc host 255.255.255.255 eq bootps

  access-list 100 permit udp host 0.0.0.0 eq bootpc host 10.77.5.1 eq bootps

  access-list 100 permit udp 10.77.10.0 0.0.0.255 eq bootpc host 10.77.5.1 eq bootps

  access-list 100 deny tcp 10.77.10.0 0.0.0.255 any eq telnet

  access-list 100 deny ip 10.77.10.0 0.0.0.255 10.77.5.0 0.0.0.255

  access-list 100 deny ip 10.77.10.0 0.0.0.255 10.77.1.0 0.0.0.255

  access ip-list 100 permit a whole

  !

  control plan

  !

  Line con 0

  session-timeout 30

  password 7 XXXX

  line to 0

  line vty 0 4

  Rotary 1

  transport input telnet ssh

  line vty 5 15

  Rotary 1

  transport input telnet ssh

  !

  Scheduler allocate 20000 1000

  !

  WebVPN cef

  !

  end

  If you want to say, that after the way nat rules which I have proposed, you lost the connection to the VLAN native, so yes, it's because the subnet VLANs native has not been included in this acl with Deny statement. So that the ACL should look like this:

  NAT extended IP access list

  deny ip 10.77.5.0 0.0.0.255 192.168.77.0 0.0.0.255

  deny ip 10.77.1.0 0.0.0.255 192.168.77.0 0.0.0.255 //This is not respected

  allow an ip

  In addition, if you want to go throug the other tunnel inside the subnet not listed above, then you should include that subnet to the NAT exemption rule with Deny statement.

• asa himself through site to site vpn access server

  Hello

  I have problem with access to the servers through site to site vpn to ASA that makes this vpn site-to-site and Clientless VPN enablerd.

  Reason why I need it / what I do:

  ASA 5510 enabled Clientless VPN and on this Portal allows users to access internal servers through bookmars URL. We use it when someone wouldn't access IPSec VPN or in an internet café. If this user connects to clientless vpn and click on the bookmark to access for example mail server. But there is problem, asa cannot access this server through VPN site-to-site.

  Network:

  Here's a quick design of my network.

  

  I don't have server access to the problem in the VLAN 159 of VLAN 10, or 100. But I need to be able to access the server in Vlan 159 of ASA 5510, who owns the IP 192.168.1.4.

  I have this subnet ASA owned by FRONT-NAT object in the same place that VLAN 10 to 100 are and vpn Site-to-Site profile.

  What I makeover or how can I solve it?

  Thank you

  Clientless VPN when accessing internal servers, it will use the closest to the source of the connection interface and if you connect to via clientless SSL VPN ASA5510 and need access ASA5505 LAN via the site to site VPN, the interface closest to the ASA5510 to ASA5505 LAN is ASA5510 outside interface, therefore, the vpn of site-to-site crypto ACL must match on ASA5510 outside the ip address of the interface.

  Here's what you need on each ASA:

  ASA5510:

  permit same-security-traffic intra-interface

  ip 192.168.159.0 external interface allowed access list 255.255.255.0

  ASA5505:

  ip 192.168.159.0 access list allow 255.255.255.0 host

  In addition, also need to add the same ACL for access-list of exemptions on ASA5505 NAT:

  ip 192.168.159.0 access list allow 255.255.255.0 host

  Hope that helps.

• ASA VPN on physical IP address only?

  Hello

  Is it possible to set up a virtual IP address dedicated to endpoint on ASA VPN version 8.3 and later?

  I don't want to use the physical IP address on my external interface.

  Thank you

  No problem. Mark pls kindly responded to this post like so that others may learn from your post. Thank you.

• Data capture ASA VPN

  Hello

  We have an asa 5585 on the network and it is configured for remote access VPN with RSA.

  When a VPN user connects to their VPN, he is invited for a PIN followed their secure ID token code.

  We want to simplify our VPN configuration if we starting from a perspective of support and management, users use a hard chips. Currently, many lose their chips or have a connection problem, so I would like to know what simple VPN solution, we have in place.

  Then is it possible on the ASA when I check my VPN traffic to determine what users are using the VPN for, since the purpose is if they only use it for email, so we can advise them to use webmail rather and can disable VPN access.

  With respect to the VPN, I see only two options; you either empty tokens to make life easier or you keep them and put up with it.