OptiPlex 7040 Micro screws missing and clips for WiFi card

Similar Questions

• OptiPlex 7040 Micro missing heatsink heat from the chipset - is this normal?

  I bought an OptiPlex 7040 Micro system about two weeks ago. After the opening of the system, I noticed that the heatsink for the chipset (Q 170 Skylake) is missing. You can see in the image below.

  

  Photos of the user, in fact downloaded manual from Dell, you can find the image with a heat sink as usually installed on motherboards.

  

  Because the German Customer Service isn't really a help for me, they always send me different pictures of the other motherboards than mine, sometimes of the previous Micro 9020, my question is this:

  Really missing heatsink (accidentally forgot to install at the factory) or is it planed out of the system for reasons?

  Because I don't want to let change possibly latest main map by an elder of the customer service to the Germany, it would be good if someone relay knowing that the facts could answer.

  There is no heater on this chipset on the 7040 M.

  I checked the internal images of the motherboard, and they show no heatsink during this particular chip.

  Also on your image of the motherboard in your system, you will notice that there are 2 positions on the motherboard where the clip holders would be located (circled in white) and real clips are not soldered to the motherboard showing that the radiator and the following clips are not needed

  

• Please help: registry error 80246008 BITS missing and service for win vista 32-bit

  Hello, I am running Windows Vista Home Premium 32-bit with SP2 and recently met a problem trying to get windows updates. I spent days reading post and the windows support and community application solves nothing doesn't. I receive the error 80246008 so they were trying to get updates. I followed of many positions and patches with a limited degree of success recommended. I have windows update to activate and my COM + service is on and working but my smart information transfer Service does not appear in my register and the list of services. I saw the patches for other versions of windows, but not for Vista, maybe I'm just blind? Any help would be greatly appreciated even if your just pointing me in the right direction. On another note, I can't get MSE update of virus definitions, related question, I guess? Don't know if this helps, but if there is any other information I can provide to assist with a solution let me know and ill update this post with it. A hugh thanks to anyone who can help.

  Hi Thagangrel,

  I see that you get the error 80246008 while trying to install updates. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. you make changes to the computer before the show?

  3. who update fails with this error?

  Method 1.

  Run the utility of automatic troubleshooting of this article.

  Windows Update, error 80246008: http://windows.microsoft.com/en-US/windows-vista/Windows-Update-error-80246008

  Method 2.

  Follow the steps in this article.

  Windows Update, error 80246008: http://windows.microsoft.com/en-US/windows-vista/Windows-Update-error-80246008

  Method 3.

  Start the computer in safe mode with network and perform a virus scan.

  Start your computer in safe mode: http://windows.microsoft.com/en-SG/windows-vista/Start-your-computer-in-safe-mode

  You can run the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 4.

  I suggest that you can exercise SFC scan and check if that helps. The SFC/SCANNOW command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  For more information how to make SFC / scan, please follow this link: http://support.microsoft.com/kb/929833

  Method 5.

  Start the computer in a clean boot state and then try to install the updates. A clean boot to test if any element of service or third party application startup is causing this issue.

  How to troubleshoot a problem by performing a boot in Windows Vista or Windows 7:http://support.microsoft.com/kb/929135

  Note: Once you have finished troubleshooting, follow step 3 in the article to start on normal startup.

  Refer.

  Problems with the installation of the updates: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-problems-with-installing-updates

  Try these steps and let us know the status.

  Thank you.

• Satellite P300 - stuttering with new BIOS and drivers for sound card

  I have Toshiba laptop Satellite P300 (PSPCCE) with Vista and the latest patches installed.
  Everything was working ok until I installed the last set of patches, has been the Tempro alert about them. I installed the new BIOS (3.40) and card drivers his (Conexant 4.83.1.0) and now all the minutes I see spike high CPU spike freezing enemy of system one or two seconds.

  I see in Process Explorer these spikes are caused by the system and that usually means drivers.
  Anyone else noticed something similar since the last update?

  BTW. There are 2 audio drivers to download site, 4.36.10.0 the 25.05.2009. but the file is named 20081201122001 sounds. ZIP and 4.83.1.0 as of the 07.05.2009. named sound - 20090507143928.zip but with a date more recent AI apparently from 2008.

  > btw. There are 2 audio drivers to download site, 4.36.10.0 the 25.05.2009. but the file is named 20081201122001 sounds. ZIP and 4.83.1.0 as of the 07.05.2009. named sound - 20090507143928.zip but with a date more recent AI apparently from 2008.
  I think that you should use the most recent version and it s a v4.83.1.0. It seems that the v4.36.10.0 was published also, but in this case, it s always recommended to take a newer version.

  With regard to the system of freezing for a second or two:
  I think that this might be related to some background processes. Perhaps a process that runs in the context of the Vista operating system causes this tiny interruptions.

  Of my knowledge tool Tempro runs in the background and scans the system and HARD drive.
  You can check the processes in MSCONFIG and if necessary may disable some of the trials.

• Satellite P100-437: cannot find modem and drivers for sound card for XP

  I can not find modem and audio drivers for windows XP. Help, please.
  Thanx

  Hello

  Satellite P100 - 437 (PSPAGE) shipped with Vista. Am I wrong?
  I think this is a reason why this series is not listed on the page of the Toshiba driver at the moment.

  Have you tested the drivers from another P100 series? Some devices come with the same material specifications and possibly other drivers will run.

  Maybe an additional info about the card and the modem will help you;
  It s a good Conexant chip and modem Conexant. Therefore you must find the Conexant audio drivers and driver Conexant modem software in the net.

• After my last update to Vista, my usb and slot for cf card readers were not mapped. I need to access. Difficulty?

  I updated Vista Friday, 11/09/2011 with KB2533523, KB2468871 and KB2310138.  After the update, I lost my backup drive Seagate mapping and my maxtor drive and card slots on the front of the desktop computer.  Tried running the fixit Center and it crashed.  I can still get to my CF card of the Canon camera via USB connection software - is not acceptable.

  Hello

  I would say you can place the computer in a clean boot state and then try to install the updates that to and check if it helps.

  Note: after the installation of each update to restart the computer, so that we can confirm which updates is causing the problem.

  How to solve the problem by running the clean boot in Windows 7:
  http://support.Microsoft.com/kb/929135 Note: once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual

  Hope the information is useful.

• OptiPlex 7040 MT: Caddy to drive 2.5 "(emplacement 2.5") "

  The Dell Optiplex 7040 has MT of 2 slots for adding new hard drives 2.5 ".

  However. instead of the standard width 2.75 "(pour un nouveau supplémentaires 2.5" disque SSD), housing seems to be approximately 3.25 "wide.

  Any suggestions as to what part number is required to mount the disk 2.5 "in the designated location 2.5" are appreciated. Thank you.

  Hi Currin,

  Please write to us.

  There are two brackets for size

  X9FV3: for 2.5 "caddy

  0CW33: for 3.5 "caddy

  We provide system tag #, e-mail address and your name via private message, by clicking on my name in blue and then select send a private message

  Concerning

• HP Pavilion dv6 6c51ea: upgrade of the dv6 6c51ea ssd and ram wifi card

  Hello
  As of late I thought the upgrade or replace my laptop, but I have a few questions to help me decide.
  First ram cited the speed of the processor is listed as 1066/1333 hz, however I can not check it on the site of hp and the crucial site recommend ddr3 at 1600 hz, the site hp also says is that 8 GB however apparently due to the fact that it was released on Windows 7 However the processor can support 16 GB max memory support and since upgrading to win 10 my system would be doing, is this correct?
  
  What kind of improvements I see by installing an ssd (Samsung evo 850) 500 GB?
  
  And finally the wifi card could be readily available and upgraded to the new ac wifi to use the router to HQ and speeds mon is provides and I pay!
  
  So basically will be the ssd, 2 x 8 GB 1600 mhz sodimm ram, and a wifi amd card equipped for the £300 it cost would he give me the jump in performance for his money as the cpu and gpu are rather dated now (i5 2450 m and radeon 7470 m) when a new system with an i5 4th gen with 1 GB graphics , 500 GB and 16 GB of ram, ssd would cost about £900 what would be the main benefits
  
  Thank you very much
  
  Shott

  I stand well partially corrected. The 8 gig RAM max was on the technical page of HP and the maintenance manual says maximum 16 concerts. As you note, it will run at 1333 mhz, but yes you can install 16 gigs and upgrade to Windows 10 made no difference there. You may installed 16 concerts with all 64-bit operating systems.

  Here is the Manual:

  Your repair manuals

  Page 28 - 29 a the list of supported wireless adapters EXCEPT the

  Module Intel Centrino Advanced-N 6230 WLAN 631956-001

  a mistake is well-documented. The part number is actually a single band card Ralink and other versions of HP of the 6230 Advanced-N used in some business models will not work in your laptop. We beat this horse dead on many posts here.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP Pavilion g7-1260us: I need a new WiFi card! What works for me

  I really need a new WiFi card that came with my computer is terrible, I need one with the support of dual band, and I would also support bluetooth as well. But Ive been told that a white list in the bios allows me to.

  Ive been resembling different wifi cards and I have the Intel 7260.HMWG network. R

  Wil this work for me if I install it?

  If not can you tell me another powerful Dual Band (and bluetooth possible) Wifi card?

  my computer is HP Pavilion g7-1260us

  BIOS: Insyde F.66

  You have been informed correctly. There is a white list of BIOS. You can use the wifi cards on page 26 and 27 of the manual here:

  Manual

• Series/PS2 for Optiplex 3020 Micro card

  I need a 'real' serial port on a number of Optiplex 3020 Micro systems and cannot find the Dell Reference number for the card series/PS2 option.

  I have studied the possibility of using a USB-to-Serial adapter, but was deterred by the seller of software and accessory equipment which should be connected via a serial port.

  Several articles seem to indicate that there is a series/PS2 expansion card:

  Support the map article does not work: ' OptiPlex 3020 M / 9020M serial port does not work.
  www.dell.com/.../EN

  OptiPlex 3020 manual (page 30): "Installation of PS2 and series connector Board.
  www.manualowl.com/.../430454

  All I can offer is the Dell USA = part number
  WN80W - Council of Wistron IO with support, cable, screws

  You will need to contact Dell for your country and see if the part number is the same or different.

• Missing notification icon for wireless keyboard and mouse in the systray area.

  Missing notification icon for wireless keyboard and mouse in the systray area. Was working before the hard disk crash. Had to reload Windows Vista 64 bit OS. Have computer model gateway GT5678.

  Chances are good the software to include these icons in notification tray cam pre-installed on the bridge.  If you still all original gateway software, try to see if something in the menu start / all programs of the gateway seems as it can contain controls for these settings and run the program to check and see if it does.  If none of the gateway software help (assuming that all this is still installed) and re-installing the drivers did not work and there is no controls at the keyboard or the mouse, so I know what else to think.  These icons are not available with Vista - they were installed by a third-party device or software driver.

  I'm sorry that gateway could not help you.  They are those that you need to do to solve this problem, because it is something that they installed with the original computer which is not re-installled after you change hard drives.  They should know what software for it and power point yoo to a download site, or you send a disk with this software.  We can't really do anything else to help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Request for block of power SUPPLY Dell optiplex 7040 Mini-Tower

  I intend to buy optiplex 7040 MT at end of game. So I would like to know:

  1. the motherboard has the processor power connectors and standard motherboard or owners?

  2. is it possible to replace the stock power supply with a cooler master extreme power 600W more? If not, what more than size of power supply fits there?

  3. is it possible to mount a gtx 1080 in there?

  Hi iamprateekprakash,

  We do not recommend that it works because it has not been tested but according to your discretion, you can try, but as you rightly noted that it might void the warranty with Dell.

• MS Server 2008 R2 on Optiplex 7040 (USB 3.0 ONLY) can make it work, even with all the dism and patch stuff...

  Trying to install Win Server 2008 R2 on an Optiplex witch is so all USB 3.0 by using the legacy startup it will launch the installer and does NOT freeze to the main screen.  But when it comes to screen readers it says it needs a driver, but nothing does not recognize because he needs a driver to recognize the HD and needs a driver to recognize that anything that is connected to the USB 3.0 ports.

  I spent 2 solid days watching and trying different things, including the patcher software dell (who uses powershell).  It works very well.  Broadcasts usb 3.0 drivers in the build of the server, but when I boot it ti freezes at the home page because he removed the pilots using the mouse and keyboard.

  Is there anything else I can try to get this to work?  I use the wrong driver?  I tried the drivers that came with the driver update utility.  I tried the drivers from the website of intel.  Cause the main screen to be locked up with no mouse/keyboard.

  I tried inserting manual usb 3.0 (same result).

  Another way I can get it work?

  I can use 2012 R2 server (who has 3.0 drivers and hard disk drivers and see the HARD disc immediately, but I prefer to use the Server 2008)

  Thank you

  I've found a workaround. (mine)...

  If I install the 2012R2 server, it gives me a platform of USB 3.0.  from 2012, I installed 2008R2, and it worked.

  I had to use 2012 once more in repair/back window because I forgot to shoot all the drivers in 2008.

  I did once I was able to delete windows.old and now I have a fully functional 2008R2 on an Optiplex 7040.

  Of course, has been easier than all this stuff of dism.

• Hello, I had a problem with my band. It does not really suppose he numbered scenes everything in order and he has so far in until I missed an and changed for the good order. But now when I go back to where I left and I have create a new scene

  Hello, I had a problem with my band. It does not really suppose he numbered scenes everything in order and he has so far in until I missed an and changed for the good order. But now when I go back to where I left and I have create a new scene number come up as * it and I need to change personally. is their any way I can change it to order normally?

  Hello

  You can manage this through the "Manage scene numbers" option in the menu 'Production '.

  There is a setting in this dialog box to assign scene numbers automatically to the new scenes.

• Script - missing and hotfixes installed for ESX and ESXi

  Can I have the script i.e. missing and hotfixes installed for ESX and ESXi using the CLI power only? out put should be csv format

  You reset the content of the table $Results on each iteration of the baseline.

  Try like this

  $Results = @()
  foreach($esx in Get-VMHost) {
    foreach($baseline in (Get-Compliance -Entity $esx -Detailed | where {$_.Status -eq "NotCompliant"})){
      $Results += $baseline.CompliantPatches |    Select @{N="Host";E={$esx.Name}},    @{N="Status";E={"Compliant"}},    @{N="Baseline";E={$baseline.Baseline.Name}},Name,ReleaseDate,IdByVendor,    @{N="KB";E={(Select-String "(?http://[\w|\.|/]*\w{1})" -InputObject $_.Description).Matches[0].Groups['url'].Value}}
  
      $Results += $baseline.NotCompliantPatches |    Select @{N="Host";E={$esx.Name}},    @{N="Status";E={"NotCompliant"}},    @{N="Baseline";E={$baseline.Baseline.Name}},Name,ReleaseDate,IdByVendor,    @{N="KB";E={(Select-String "(?http://[\w|\.|/]*\w{1})" -InputObject $_.Description).Matches[0].Groups['url'].Value}}
    }
  }
  $Results
  

  It will give the installed and lack of patches which are defined in the non-compliant baslines related to the ESXi host.

  If you want to see all the lines, also the most consistent, omit the Where clause on the base line (foreach) loop.