order isakmp crypto problem

Similar Questions

• Deafult isakmp crypto personal - T3 IOS 15.2 (3)

  Hi all

  Wondering if the strategies presented in:

  command 'show the default isakmp crypto policy'

  are in force and can potentially be negotiated, even when I have an explicitly defined isakmp policy on allowing only configuration necessary to security protocols.

  IOS is 15.2 (3) T3

  Thank you!

  I think it will be the key to understanding:

  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/sec_conn_imgmt/configuration/15-Mt/sec-IPSec-usability-enhance.html#GUID-ECDF5542-90E7-42D4-A690-BA7520AF4E90

   If you have neither manually configured IKE policies with thecrypto isakmp policy command nor disabled the default IKE policies with the no crypto isakmp default policy command, the default IKE policies will be used during peer IKE negotiations.
  
  

• Order the crypto isakmp his poster 2 VPN

  Hi all!

  Why my router shows me 2 VPN? Is this normal?

  R1 #show crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  DST CBC conn-State id
  10.10.0.5 10.10.0.2 QM_IDLE 1870 ACTIVE
  10.10.0.2 10.10.0.5 QM_IDLE 1871 ACTIVE

  For clarity, this shows that you have two sessions of IKE.

  The situation can occur when:

  1) both sides start IKE session at the same time.

  (2) when one side initiates a generation of new key IKE SA (every 24 hours by default).

  Most of the time is not a problem.

  Check if your IPsec security associations are upward and do not beat.

  Which allows to "consignment crypto session" is probably a good way to get visibility.

• Customer VPN - client configuration isakmp crypto group missing

  Hello

  I have a 12.2 (7r) version running Cisco 2611XM

  I am trying to get the vpn clients to connect to the router following this link:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801c4246.shtml

  My problem is that when I try to add the group I do not get the group option.

  That's what I get:

  My_Router (config) #crypto isakmp client configuration?

  network address Set for the client address pool

  What I need to change the version of IOS, if yes what IOS should I use?

  Any help is greatly appreciated. This is the show of the current router version

  Cisco Internetwork Operating System software

  (Tm) C2600 software IOS (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)

  Copyright (c) 1986-2003 by cisco Systems, Inc.

  Updated Friday 19 June 03 16:35 by pwade

  Image text-base: 0x8000808C database: 0x81280FF0

  ROM: System Bootstrap, Version 12.2 (7r) [next 7r], RELEASE SOFTWARE (fc1)

  My_Router uptime is 1 minute

  System to regain the power ROM

  System image file is "flash: c2600-ik9s - mz.122 - 17A .bin.

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2611XM (MPC860P) processor (revision 0 x 100) with 60416K / 5120K bytes of memory.

  Card processor ID JAE072602F2 (1616341861)

  M860 processor: Ref. 5, mask 2

  Connection software.

  X.25 software Version 3.0.0.

  2 FastEthernet/IEEE 802.3 interfaces

  2 network interfaces Serial (sync/async)

  32 KB of non-volatile configuration memory.

  32768 K bytes of processor onboard flash system (read/write)

  Configuration register is 0 x 2102

  Thank you

  Randall

  Randall,

  TAC is more an organization of break-fix. The question that you run by being more a features/functionality with the version of the code, TAC will probably able to help.

  Your best option is to upgrade the memory and upgrade the router to 12.3 Mainline or higher.

  Let me know if it helps.

  Kind regards

  Arul

• 881 - isakmp crypto module is not available

  Hello.

  I have a Cisco 881 SRI (CISCO881-SEC-K9) and license advanced installed and enabled/active security and in use (see screenshot).  However, the isakmp encryption module is not available.

  Cisco #crypto?

  GDOI GDOI about orders

  IPSec IPSec

  the key associated with the control.

  PKI public key public

  Here is my result to "see the version.

  Cisco IOS software, software C880 (C880DATA-UNIVERSALK9-M), Version 15.0 (1) M8, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2012 by Cisco Systems, Inc.

  Updated Friday, February 16, 12 02:58 by prod_rel_team

  ROM: System Bootstrap, Version 12.4 (22r) YB5, RELEASE SOFTWARE (fc1)

  the availability of Cisco is 11 minutes

  System returned to ROM by reload at 13:47:55 PCTime Wednesday, August 22, 2012

  System restarted at 13:48:27 PCTime Wednesday, August 22, 2012

  System image file is "flash: c880data-universalk9 - mz.150 - 1.M8.bin.

  Last reload type: normal charging

  Reload last reason: reload command

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 881 (MPC8300) processor (revision 1.0) with 236544K / 25600K bytes of memory.

  Card processor ID FTX1624812T

  5 FastEthernet interfaces

  1 module of virtual private network (VPN)

  256K bytes of non-volatile configuration memory.

  125440K bytes of ATA CompactFlash (read/write)

  License info:

  License IDU:

  -------------------------------------------------

  Device SN # PID

  -------------------------------------------------

  * 0 FTX1624812T CISCO881-SEC-K9

  License information for "c880 - data".

  License level: advsecurity Type: Permanent

  Next reboot license level: advsecurity

  Configuration register is 0 x 2102

  What kind of module you are missing? Or you are missing the "crypto isakmp" command that is not available in your impression?

  If it is just the command, then go to conf-mode where you can configure isakmp and search commands «crypto isakmp...» ».

  Sent by Cisco Support technique iPad App

• order of crypto ikev2

  Hello

  I am trying to configure an IPSEC VPN on a 2821 router, but it does not accept the command "ikev2 crypto.

  I tried a few images of different software - 15.0 and 15.1 T & M train advsecurity and 15.0 advipservices. (Only have 64 MB flash so cannot load 15.1 advipservices.)

  Is there something with the 2821 that does not support ikev2? I don't remember see whatever it is in the release notes, saying: it is only supported on specific models.

  In the end, I am configuring a VPN for Windows Azure. They provide the sample configuration, (I'm working on some routers of the 880 series with 15.1 without any problem) has the following configuration:

  Azure-proposal of crypto ikev2
  encryption aes-cbc-256 aes-cbc-128 3des
  the sha1 integrity
  Group 2
  output

  Crypto ikev2 azure policy
  proposal of Azur-proposal
  output

  From: https://msdn.microsoft.com/en-us/library/azure/dn133800.aspx?f=255&MSPPE...

  Can I use this router?

  What is different between 15.1 on the 880 series at the 2800?

  Thank you

  Jon

  Hello

  I looked at browser functionality of Cisco and what I see here is that no image of 2821 does support IKEv2, and it's the end of sale now images so no new testament be released.

• Hello. I just know that the muse and I need an organization of customers in alphabetical order. The problem is that you will always get new clients. I need to know how to insert a new customer (square), and it is already in alphabetical order on the page.

  Hello.

  I just know that the muse and I need guests alphabetical organization. The problem is that you will always get new clients. I need to know how to insert a new customer (square), and it is already in alphabetical order on the page. The site will be as in the link below, and each customer will have a window of these: http://www.connary.com/. I look back.

  A hug, Murilo.

  I believe you are referring to the rectangles of tile as visitors on the page? not exactly customer database?

  You can add rectangle with different effects with rollover State of mouse and about adding new, you must do this manually in design mode.

  Thank you

  Sanjit

• Order sorting photos problem

  In the Photos, I want my photos appear in order of date/time taken, regardless of whether they have been taken on my camera or iPhone, but they are grouped (by order) depending on what device, they were taken.  Can anyone help please?

  10.11.5 Macbook pro OSX.

  In the view of Photos, they are sorted by date taken and grouped by the date.  In view of all the Photos, they are sorted by date added to the library with more recent photos at the bottom.

  However for a simple view of only the photos you want to create a smart album with the following criteria:

  

  Select a date that will precede all your photos. This includes automatically all in the library and all-new photos added.

  Then use the discover ➙ sort menu to sort by Date taken with the oldest or most recent at the top:

  

  

• ISAKMP crypto key command

  How to hide the encryption key? When I do see isakmp encryption key the I see the key in plain text.

  Kelly

  You are probably talking about IOS?

  Take a look at this link-

  http://www.Cisco.com/en/us/docs/iOS/security/configuration/guide/sec_encrypt_preshare_ps6350_TSD_Products_Configuration_Guide_Chapter.html

  Jon

• Column in line to order by items problem

  Hello
  Version 10204.
  
  I use function xmlagg in passes convert order lines.
  

  SELECT *
  from DBA_LOG_GROUP_COLUMNS
   WHERE table_name IN  ('NAP_CUST_USERS')
  order by table_name   ,position ;
  
  OWNER                          LOG_GROUP_NAME                 TABLE_NAME                     COLUMN_NAME                      POSITION LOGGING_PROPERTY
  ------------------------------ ------------------------------ ------------------------------ ------------------------------ ---------- ------------------
  PSSYS                          GGS_14831759                   NAP_CUST_USERS                 SETID                                   1 LOG
  PSSYS                          GGS_14831759                   NAP_CUST_USERS                 COMPANYID                               2 LOG
  PSSYS                          GGS_14831759                   NAP_CUST_USERS                 USERNAME                                3 LOG
  PSSYS                          GGS_14831759                   NAP_CUST_USERS                 NAP_CLOSE_DATE                          4 LOG
  PSSYS                          GGS_14831759                   NAP_CUST_USERS                 PERSON_ID                               5 LOG

  Here is how I use this:

  SELECT table_name ,
  rtrim (xmlagg (xmlelement (e, column_name || ',')).extract ('//text()'), ',') enames
  from DBA_LOG_GROUP_COLUMNS e
   WHERE table_name IN  ('NAP_CUST_USERS')
  group by table_name
  order by table_name;
  
  NAP_CUST_USERS     SETID,COMPANYID,NAP_CLOSE_DATE,USERNAME,PERSON_ID

  As you can see the order of the column in the second statement is different than in the first.
  I like to keep the position of the column, because they are in the first statement.
  Please note that there are several tables in the where clause.
  Just to keep the example simple as possible, I have mentioned only one table
  
  Thank you

  How about using the clause ORDER BY of XMLAGG?
  http://docs.Oracle.com/CD/E11882_01/AppDev.112/e23094/xdb13gen.htm#ADXDB5084

  SELECT table_name ,
  RTRIM (XMLAGG (
    XMLELEMENT (E, COLUMN_NAME || ',')
    order by column_id
  ).EXTRACT ('//text()'), ',') ENAMES
  FROM USER_TAB_COLS E
  where table_name in ('EMP')
  group by table_name
  
  TABLE_NAME  ENAMES
  ----------- --------------------------------------------
  EMP         EMPNO,ENAME,JOB,MGR,HIREDATE,SAL,COMM,DEPTNO
  

  Published by: stew Ashton on February 10, 2013 21:18

• Just ordered the download for Adobe Premier order [deleted] the problem elements is I can not download the file

  can not download the program. The program is expected to be Prime Minister 14 elements

  [NEVER SEND A SERIAL NUMBER TO AN OPEN FORUM!]

  [personal information... [Mod - https://forums.adobe.com/docs/DOC-3731]

  [This is an open forum, not the Adobe support, please do not post personal information]

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• invalid-spi-recovery crypto isakmp command worked well in the case of DMVPN

  Hello

  I did the Setup for Hub/spoke in th DMVPN case and it worked fine. But after reloading Hub and I saw an output of error below, well I added the command invalid-spi-recovery isakmp crypto in the Hub & spokes:

  * 7 Oct 03:10:03.175: CRYPTO-4-RECVD_PKT_INV_SPI %: decaps: rec would be package IPSEC a bad spi to destaddr = 150.1.1.1, prot = 50, spi = 0 x 72662541 (1919296833), port = 150.3.1.3

  * 7 Oct 03:10:03.175: CRYPTO-4-RECVD_PKT_INV_SPI %: decaps: rec would be package IPSEC a bad spi to destaddr = 150.1.1.1, prot = 50, spi = 0 x 72662541 (1919296833), port = 150.2.1.2

  Note: spoke1 IP address: 150.2.1.2/spoke2's IP address:150.3.1.3/Hub's IP address: 150.1.1.1

  My temporary solution for the same problem, I need to erase SPI by manually and it worked fine again.

  Everyone has the same problem, please let me know

  Kind regards

  TRAN

  Hello

  There is a common misconception of what the invalid-spi-recovery crypto isakmp command does. Even without this command IOS already performs a kind of recovery invalid SPI feature by sending a DELETION notify for the SA has received send peer If she already has an IKE SA with this peer. Still once, this happens regardless of whether the order invalid-spi-recovery crypto isakmp is enabled or not.

  With the order of isakmp crypto invalid-spi-recovery , he tries to regulate the condition where a router receives the IPSec traffic with invalid SPI and

  It doesn't have an IKE SA with this peer. In this case, it will try to put in place a new IKE session with the peer and then send a DELETION notification on the newly created HIS IKE. However, this command does not work in all configurations of crypto. Are the only configurations that this command works cryptographic instantiated, for example, Asit, and peer static maps from static cryptographic cards where the peer is defined explicitly. Here is a summary of commonly used configurations of crypto and know if invalid spi recovery works with this configuration or not:

  Crypto config	Not valid-spi-recovery?
  Static crypto map	YES
  Dynamic crypto map	NO.
  P2P GRE with TP	YES
  using love TP w / static PNDH mapping	YES
  using love TP w / dynamic PNDH mapping	NO.
  ASIT	YES
  EzVPN client	N/A

  For help with your scenario, you can enable DPD (isakmp crypto keepalive) on the shelf to help the recovery tunnel.

  Thank you

  Wen

• "no nat-traversal crypto isakmp" after restart

  Hello

  With the version of the Software ASA 8.0, we noticed that whenever restart us tha device, the configuration line:

  No encryption isakmp nat-traversal

  appears in the configuration.

  It is very annoying, because this NAT - T obviously does not work.

  Any of you noticed that too?

  Ideas?

  Thank you very much.

  Marco Pizzi.

  Hi Marco,.

  This is a bug in the version of the ASA 8.x software and there are workarounds:

  CSCsj52581 Details of bug

  No inconsistent configuration of nat-traversal isakmp crypto after reboot

  Symptom:

  After a restart of the ASA at the global order "no isakmp encryption".

  NAT-traversal.

  appears in the running-config even it is not available in the

  startup-config.

  Conditions:

  None

  Steps to reproduce:

  BSNs-ASA5505-1 (config) # nat-traversal crypto isakmp

  BSNs-ASA5505-1 (config) # copy run start

  BSNs-ASA5505-1 (config) # sh run all | NAT Inc

  Crypto isakmp nat-traversal 20

  BSNs-ASA5505-1 (config) # sh start | NAT Inc

  BSNs-ASA5505-1 (config) #.

  After reloading of the ASA:

  BSNs-asa5505-1 # sh run all | NAT Inc

  No encryption isakmp nat-traversal

  BSNs-asa5505-1 # sh start | NAT Inc

  asa5505-BSNs-1 #.

  Workaround solution:

  (1) use a default value, for example, "crypto isakmp nat-traversal 21.

  (2) to activate the "crypto isakmp nat-traversal" after the restart of the ASA if you

  You can use the default value. The default value is: crypto isakmp

  NAT-traversal 20

  Radim

• No crypto isakmp ccm

  Can someone tell me or point me to the right direction to find out, what is / was the subject of the order "crypto isakmp ccm. ?

  I need to explain to a customer, and I can't find any information on this subject. I checked every reference command 12.x and I didn't find a thing.

  I've seen many examples of configs with "no crypto isakmp ccm", but nowhere can I find an explanation on this subject,

  Concerning

  Ariel,

  CCM stands for Protocol of CCM (CCMP).

  The message 'no ccm isakmp crypto' is not

  of all fear, because it's just letting you know that you have not implemented the Optional Protocol of the CCM (CCMP).

  CCMP is a data security protocol that handles authentication and encryption package. Privacy, CCMP uses AES in counter mode. For authentication and integrity, the CCMP uses Cipher Block Chaining Message Authentication Code (CBC - MAC). In the IEEE 802.11i standard, CCMP uses a 128-bit key. The block size is 128 bits. The size of the CBC - MAC is

  8 bytes and the size of Nuncio is 48 bits. There are two bytes of overhead IEEE 802.11. CBC - MAC, the Nuncio and the overload of IEEE 802.11 enlarge the CCMP 16 bytes only one unencrypted IEEE 802.11 packet

  package. Although somewhat slow, the biggest package is not a bad exchange for increased security.

  CCMP protects some of the fields that are not encrypted. Additional parts of the IEEE 802.11 frame get protected are known as additional authentication (AAD) data. AAD includes source and destination packages and protects against attacks from re-reading of the packages to different destinations.

  Let me know if it helps.

  Kind regards

  Arul

• Debug Crypto ISAKMP

  Hello

  I've been trying to set up a virtual private network and when I ran this command earlier I received a lot of output and everything seemed ok.

  I could see also dest, src, etc... When I ran isakmp crypto his.

  All of a sudden I have nothing now, even when I debug above. His crypto isakmp command is now empty, too, see below.

  crypto ISAKMP his

  IPv4 Crypto ISAKMP Security Association

  status of DST CBC State conn-id slot

  Suggests that the problem is with the remote end? I'd always get the display using debug crypto isakmp if the remote end is down to debug?

  Just puzzled as to why the power has disappeared 'quiet '.

  Thank you

  Hello

  There could be several reasons for the same thing:

  --> Interesting traffic or other remote or local end has been interrupted for any reason any.

  --> That the ASA has been showing some debugs earlier, it is unlikely that the package can't the ASA now which in turn will hit the crypto ACL (interesting traffic) triggering therefore Cryptography tunnels and debugs him.

  --> There could be changes in configuration to the remote end ASA because of which the tunnel is not triggered.

  The best way to solve this problem is to follow the VPN traffic or the package for tunnel VPN from its source to its destination.

  I recommend the following:

  • Take screenshots on the SAA hence traffic is running and see if it's the ACL crypto. Check the ACL has hit counts for the same.

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a0080a9edd6.shtml

  • Select "debug crypto isakmp 127' & see if the tunnel is triggered and debugging is generated.
  • If not, then run the packet tracer and see if the VPN traffic passes all the checks, and that he is authorized by the VPN.
  • If traffic is allowed under the VPN to tracers of package Phase, and you still do not see the traffic being passed through the VPN, then it might a possibility that is happening in a different tunnel and pressing a crypto ACL overlap (as appropriate) on the same source ASA.
  • If the package is not seen hitting the firewall of the above capture, then the package can't certainly ASA and you will need to check the internal routing.
  • You can also see that the syslogs on the ASA local drops because of any function of firewall for VPN traffic destined for.

  To respond to your request, if the remote end has been down you wouldn't see debugs it unless the host is launch of traffic to the VPN to the local line. If the VPN traffic has been initiated by behind the ASA remote, and it is down then you would see not all debugs on the ASA local.

  I would like to know once you have reduced it more so that we can move forward and I'll be in a better position to provide my next course of action on this.

  Hope this has been informative.

  Kind regards

  Nick

  P.S. Please mark this post as solved if the information above has helped you identify the problem or at least you move forward to resolve the issue so that other users are benifited too