PAGINATION OF DATA KERNAL ERROR
I am facing this error after it crashes. It appears a blue screen and will eventually return to the page of windows 8.
Tags: Windows
Similar Questions
-
I have dell 1545 laptop inspiton. for last 4 months if I want to install wibdows 7 ther may be an error with kernal data inpage error blue screen. I have run CHKDSK/p & CHKDSK C: /F /Rcommand but after the problem is continuous. Please tell me my hard drive is bd or I have to buy new hard drive?
Hello
Take a look at the answer in the following link:
http://social.technet.Microsoft.com/forums/en-us/w7itprohardware/thread/7b354864-297e-428A-9026-bfd822137ef1Thank you
-
data paging error / kernel stack inpage error
Just starting to get these errors. I have a background of both limited computer posted patches go well above my head. I tried to do a little, but I have to do something wrong. Could someone help guide me through these errors solved? I can boot the computer and restart it. This all started when I was on a game (taptiles) and he hit me, and then I couldn't get back to the game at all. Then I started having problems when on the internet, it would be just me kick out unexpectedly. Now I only can access internet with chrome, can not access a recognizable homepage from internet explorer, the page is all the sentences and invite you. Any help you could provide would be wonderful.
Original title: How can I correct an error in pagination of data from the kernel / kernel stack inpage error on windows 8
Hello
Thank you for visiting Microsoft Communities.
I understand that you get the error message, and as you have problems with Internet Explorer.
Sorry to hear about the inconvenience caused. Do not worry, we are here to help.
Method 1: Microsoft online analysis
http://www.Microsoft.com/security/scanner/en-us/default.aspx
Download this online scanner and perform a full scan on the computer. This will remove any virus infection that is in the computer.
Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
Method 2: Check disk
This stop message indicates that the data page of the kernel of the required paging file cannot be read into memory. This stop message is usually caused by a bad block (sector) in a swap file, a virus, a disk controller or failing RAM error. In rare cases, it is caused when the resources of non-paged pool is exhausted. It is also caused by the defective material.
Right-click on the windows on the lower corner flag on the left
Select prompt (Admin)
This will open the command window and type please Chkdsk /f /r and press ENTER.
It will introduce the drive check and look for errors and try to remedy.
Note: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
For more information about the error, please see the link below:
Error message: KERNEL_DATA_INPAGE_ERROR
http://msdn.Microsoft.com/en-us/library/ms854944.aspx
For Internet Explorer related issue please follow the article below:
http://Windows.Microsoft.com/en-us/Internet-Explorer/IE-crashes-stops-working#IE=IE-10
Note: The feature reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Reset Internet Explorer is not reversible, and all the previous settings are lost after reset.
I hope this helps. And please answer if you still need help.
-
Satellite A300D-135 - BIOS - System Configuration data read error
After starting a Satellite A300D-135 laptop computer, the following error message appears:
3070M extended RAM passed
512 KB of L2 Cache
System BIOS with a shadow
Video BIOS with a shadow
ATAPI CD-ROM: TSSTcorp CDDVDW TS-L632H
Fixed disk 0: TOSHIBA MK2546GSX
Initialized the mouse
ERROR
System Configuration data read errorPress
to resume, installation After pressing F1 the machine starts Windows, very well, but the error message is quite irritating, while it comes with a loud BEEP
I tried the following things so far (in that particular order):
-Load BIOS default
-Flashed the BIOS with the latest version of the BIOS (2.80) for this type of model
-Reinstalled windows with HARD drive formatAll the these did not work.
I saw the same message appearing on several places on the internet (on different laptops with a Phoenix BIOS in common), but so far I have not been able to find a working solution.
It might me a hardware problem, but all devices (vga, soiund, lan, wifi, usb, hdd) seem to work perfectly under Windows, so this does not seem the question). Another solution that is mentioned in some forums, replace the battery. But because the phone keeps time correctly I don't think it's the case either.
Any ideas?
Kind regards
GJHello
The POST (power on self-test) BIOS checks and detects errors on the motherboard.
I think it has something to do with the hardware on the motherboard problem.
I doubt that you can solve this if update of the BIOS and the BIOS default settings didn't change that.What to say; I think that the technician of the ASP should run tests to check what's wrong or what cause this I think it is question of s mobo.
-
Satellte M30: BSOD - KERNEL DATA INPAGE ERROR atapi.sys
Hello
I really hope, really, that someone can help me. I'm no computer Wizard, so if you can help please give me simple instructions. My problem is that often my satellite M30 freezes and blue page happens to give me a warning.
Top of the page is KERNEL-DATA-INPAGE-ERROR, then goes on to say disable Options memory BIOS such as cache or shading, atapi.sys says below.
So can someone please help.
Thank you
Hello
Because you are not a computer expert ;) I'll try to write as simply.
It looks more like a hardware problem as a problem of software!But to be 100% sure, you should recover the laptop with the Toshiba Recovery CD supplied.
This CD will be programmed the laptop back to the factory setting and usually the laptop should work properly after the recovery of the new!If you the BSOD will appear again the chances are high that memory, HARD drives and the motherboard is malfunctioning.
But because you are a beginner, I would not recommend trying to solve this problem yourself.
In this case, you must contact the ASP in your country!Good luck
-
Equium A300D - 13 X - Configration system data read error
Hello
I have a problem with my Equium A300D - 13 X laptop, everytime I turn on my laptop it starts and loads the initial startup screen as usual, Toshiba once asked that loud "BEEP" comes from my laptop, and lists the following information:
Phoenix TrustredCore (tm) NB
Copyright 1985-2006 Phoenix Technologies Ltd.
All rights reservedHerring of the ITA (DDR2 + T/RS690M/SB600)
CPU speed = 2000 MHz639K system spent RAM
1918M extended RAM passed
1024 KB of L2 Cache
Occult system BIOS
Video BIOS with a shadow
ATAPI CD-ROM: MAST * ADVD-RAM UJ-850 S
Fixed disk 0: WDC W2500BEVT-00SCSTO
Fixed disk 1: Hitachi HTS542520K9SA00
Initialized the mouse
ERROR
System Configuration data read errorPress
to resume, installation I replaced the hard drive and flashed the BIOS settings as advised by Toshiba Helpline but the problem persists.
Help, please! because the "BEEP" is now getting on my nerves!
See you soon
Hi andrew_net82,
It seems that the BIOS has detected an error with a certain part of material...
Before doing something I recommend you load the default settings in the BIOS. If you are in the BIOS Setup, press the F9 key.
If it doesn t work you need for professional assistance from an authorized service I think. Guys need to check which part of the material is defective and must be replaced.
List of the ASP, you can find on the official website of Toshiba. -
Data length error! Helps the release of Keyence micrometer
I am connected to a micrometer of LS7600 Keyence, and I am able to send commands to the micrometer, as well as receive structred outputes. For example:
Command: M0, 1
Return: ER, M0, 20
Soul ER error, M0 is my exit command, and 20 means DATA LENGTH ERROR.
I use a very basic VISA program that connects to the Keyence via my Serial Port.
So when the micrometer Keyence attempts to send the data I requested, it apparently can't do because it encounters a data length error. I know it's a problem with my labview software because I can output these values successfully using a Hyperterminal connection.
The data SHOULD go back which looks like this: M0 + 25.2531
It's just 12 bits? Can anyone think why labview does not accept this string?
Check the display format of the indicator, that you look at the number. It by default 6 significant digits, is exactly what you say.
The integer is in the orange wire, just your indicator is not set to show them all to you.
-
Blue screen and CORE-DATA-INPAGE-ERROR Message
The blue screen and the CORE-DATA-INPAGE-ERROR Message appeared during extract some files, 2 consecuentlly. It has happened too, but not that often and during other processes. What should I do? The OS is Vista Home Premium.
Indeed, I am here!
Thank you for fixing links.
The attached file of the DMP is to bug checking KMODE_EXCEPTION_NOT_HANDLED (1e) .
This indicates that a kernel-mode program generated an exception which did not catch the error handler.
8th error checking, {c0000005, 9eaa4efc, e551bae0, 0}
0: kd > 9eaa4efc ln
(9eaa4eb2) win32k! PFEOBJ::vFreepfdg + 0x4a | (9eaa4f65) win32k! MultiUserGreTrackRemoveEngResourceThe exception is produced in win32k! PFEOBJ::vFreepfdg + 0x4a.
0: kd > k
ChildEBP RetAddr
e551b6a0 84071908 nt! KeBugCheckEx + 0x1e
e551ba70 8409584 has nt! KiDispatchException + 0x1a9
e551bad8 840957fe nt! CommonDispatchException + 0x4a
e551bafc 8401e70c nt! KiExceptionExit + 0 x 186
e551bb64 9eb38a95 hal! KfLowerIrql + 0 x 64
e551bb84 9eafac21 win32k! RFONTOBJ::vDeleteRFONT + 0 x 130
e551bbbc 9eafada2 win32k! vRestartKillRFONTList + 0x7b
e551bbf0 9eaafcd7 win32k! PFTOBJ::bUnloadWorkhorse + 0 x 115
e551bc1c 9eaaf8d9 win32k! vCleanupPrivateFonts + 0x4d
e551bc34 9eaac06e win32k! NtGdiCloseProcess + 0x16c
e551bc54 9eaabbad win32k! GdiProcessCallout + 0 x 145
e551bc70 84262 has 48 win32k! W32pProcessCallout + 0x5d
e551bcdc 8423f47f nt! PspExitThread + 0x4a0
e551bcf4 840fde8e nt! PsExitSpecialApc + 0 x 22
e551bd4c 84094d 42 nt! KiDeliverApc + 0x1dc
e551bd4c 77a95d14 nt! KiServiceExit + 0 x 56
WARNING: Frame IP not in any known module. Sequence of images may be wrong.
04adf6dc 0x77a95d14 00000000Associated police crashes, likely a buffer overrun.
---------------------------------------------
1. remove the font cache and then restart > C:\Windows\System32\FNTCACHE. DAT
* I recommend that you create a system restore point before that just to be sure: Vista - START | type rstrui - create a restore point.
2 you have avast! + Security installed Aladdin, is at the origin of the conflict.
Remove and replace avast! and Aladdin with temporary Microsoft Security Essentials for troubleshooting purposes:
avast! removal - http://www.avast.com/uninstall-utility
MSE - http://Windows.Microsoft.com/en-us/Windows/Security-Essentials-download
3 uninstall Smart Defrag as soon as possible.
4 uninstall RealNetworks as soon as POSSIBLE, the drivers are too old - 2003.
Kind regards
Patrick
-
OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:9D.03 BIOS version
632K RAM passed system
3966M extended RAM passed
1024 KB of L2 Cache
System BIOS with a shadow
Video BIOS with a shadow
ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
Fixed disk 0: WDC WD2500BEVS-26VATO
Initialized the mouse
Updated System Configuration data
ERROR
System Configuration data read error.I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).
If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.
At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.
http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!
-
Kernel data Inpage Error... Memory dump... Please help me
Hi my name is shoaib.
I am facing a problem of blue screen approximately every 20-40 minutes. I run the memory test and you indicates no error. I check the RAM via the command "mdsched.exe" and she also don't say no found error. But when the blue screen appears it is said on the top of the page "kernel data Inpage Error".
Please tell me what to do?
Here is my file link "msinfo32".
http://1drv.Ms/1Lu9SpH
I have not found any "directory Minidump" in C:/windows. Please suggest me what to do. I really need your help. Thank you
If you stopped crashing run a trace of windows performance when you encounter the problem
In order to diagnose your problem, we need run Windows performance toolkit, the instructions that are in this wiki
If you have any questions do not hesitate to ask
Please run the trace when you encounter the problem -
0X0000007A (KERNEL DATA INPAGE ERROR)
Hello, I got a screen blue error during the game or just overall being on my pc, but it seems to happen more when I have the game. The code is '0x0000007a (KERNEL DATA INPAGE ERROR)' I did 3 bugs so far.
1. CHKDSK C: /F /R (http://goo.gl/cQCQj2)
2 memory diagnostic tool (https://neosmart.net/wiki/0x0000007a-kernel-data-inpage-error/)
3. fix (when I tried fix it says update applicable to your computer)
These accidents are called BCC116 and are associated with your video subsystem. Please follow the instructions of this wiki -
Dat2.data version error
I get the dat2.data Version error when I try to print, or even to open Microsoft Word 2007. It started when I loaded the new epson drivers on my computer. I tried to uninstall the epson SW but it won't let me, it times out.
Hi Tom Callaghan,.
Welcome to the Microsoft Answers community.
Do you have which version of the driver installed?
You can install the old driver version and check.
I suggest to start your computer in clean boot mode, and then uninstall the printer driver and restart your computer. Reinstall the printer drivers.
Method 1: Steps to uninstall and reinstall the printer driver.
1. click on the Start button and select Control Panel.
2. click on programs.
3. click on programs and features.
4. now uninstall the printer drivers.
5 restart your computer. This will automatically install the appropriate drivers for it.You can also download the driver for it from the manufacturer's Web site.
http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?OID=-10222&infoType=overview
Method 2: Steps to start in clean boot mode:1. click on start, type msconfig in the search box and press ENTER.
If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
2. in the general tab, click Selective startup.
3. under Selective startup, clear the check box load startup items.
4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
5. click on OK.
6. When you are prompted, click on restart.http://support.microsoft.com/kb/331796 . In addition, see the section on how to restore your computer to a Normal startup mode.
If the methods above does not solve your problem, and then run system restore.Method 3: System Restore will take your computer state permeable when it did not face such a problem, this can be done by selecting the correct restore point.
To restore the operating system to an earlier point in time, follow these steps:
1. Click Start, type system restore in the search box, and then click System Restore in the list programs.
If you are prompted for an administrator password or a confirmation, type your password or click on continue.
2. in the System Restore dialog box, click on choose a different restore point and then click Next.
3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.
4. click on finish.For more information, visit the links below:
http://support.Microsoft.com/kb/936212/
http://support.Microsoft.com/kb/826862Hope this information is useful.
Let me know if it worked.
Thank you, and in what concerns:
Umesh P - Microsoft Support -
CanoScan 4200F gives error - "Twain data transfer error".
I have a new Windows 7 PC and unable to use CanoScan 4200F, he returns with "Twain data transfer error". Worked fine with Windows XP. What should I do
to make it work?
Check the manufacturers technical support for latest drivers site, they have Windows 7 drivers that you can download and install. Download little correct level for your computer - 32 or 64 bit - and then install them.
CanoScan 4200F drivers:
http://www.USA.Canon.com/Cusa/support/consumer/scanners/canoscan_series/canoscan_4200f?selectedName=DriversAndSoftwareTo see if you have Windows 7 32-bit or 64-bit:
- Open system by clicking the Start button, right-click computer, and then clicking Properties.
- Under system, you can view the type of system, it will say 32 or 64 bits.
How to install a Scanner:
http://Windows.Microsoft.com/en-us/Windows7/install-a-scannerWorking with the scanner and Camera Installation Wizard:
http://Windows.Microsoft.com/en-us/Windows7/working-with-the-scanner-and-Camera-Installation-Wizard -
Kernel data inpage error foolowed by 0xc0000185
If this started a few weeks ago about every day or if I get this error called kernel data inpage error http.sys
I decoded to ignore it because it would just restart it self but since yesterday it happens whenever I start my laptop if his sleep or stop and when it restarts it says my laptop needs to be repaired error code: 0xc0000185 what should I do? I tried check disk but he asked me to make a volume of check on the next reboot and im a little scared to restart im using sfc/scannow and I also checked all my hard drives for errors in the Properties section there were no errors.
any ideas? IM using a lenovo G510
2: kd > .bugcheck
0000007 a Bugcheck code
Arguments fffff6fb '400c9ce8 ffffffff' c000000e 00000000' 42e19880 fffff680'1939 d 0002nd arg NTSTATUS 0xc000000e says a device randomly lost its existence and attempted to be referenced (usually the hard drive).
2: kd > knL
# Child - SP RetAddr call Site
00 ffffd000 ' 22378478 fffff801' 00d869db nt! KeBugCheckEx
01 ffffd000 ' 22378480 fffff801' 00c739e0 nt! : FNODOBFM: 'string' + 0x1881b
02 ffffd000 ' 22378570 fffff801' 00c6068a nt! MiIssueHardFault + 0 x 184
03 ffffd000 ' 22378630 fffff801' 00c55e31 nt! MmAccessFault + 0x5ba
04 ffffd000 '223787f0 fffff801' 01208f65 nt! MiCommitExistingVad + 0 x 901
05 ffffd000 ' 22378920 fffff801' 00d694b3 nt! NtAllocateVirtualMemory + 0xfbd
06 ffffd000'22378 b 20 fffff801'00 d 61900 nt! KiSystemServiceCopyEnd + 0x13
"ffffd000 07 ' 22378 d 28 fffff801 ' 010983bd nt! KiServiceLinkage
' ffffd000 08 ' 22378 30 fffff801 d ' 0102903d nt! RtlCreateUserStack + 0x19d
09 ffffd000 '22378e20 fffff801' 0101f685 nt! PspAllocateThread + 0 x 385
0a ffffd000 ' 22379080 fffff801' 0101f327 nt! 0x1f1 + PspCreateThread
0 b ffffd000 ' 22379340 fffff801' 00d694b3 nt! NtCreateThreadEx + 0x21f
0 c ffffd000 '22379a 90 00007ffe' c1691cda nt! KiSystemServiceCopyEnd + 0x13
0d 00000032' 00000000 00000000 '0x00007ffe' c1691cda of 739aee08Looking at the stack, we have created a thread that was used to allocate virtual memory and we went off the rails on chassis #04, committing existing an existing virtual address.
In fact, I think that this may be a side effect of an AVG bug, rather than a bad hard drive. I would recommend remove AVG first and see what happens.
-AVG removal http://www.Avg.com/us-en/utilities
Windows Defender (how to activate after removal)
A.Navigate ofControl Panel (with icons). You can do this by typingStart > Search > Panel. Once in the Control Panel change the drop-down menu of thecategory to large or small icons.
B.Among list icons, and then click Action Center.
C.Assuming that the deletion of your previous anti-virus software has gone well, you will notice for unexpected and spyware software (important) protection and Virus protection (important), it will have a button that says turn on now. Click on this button (no matter that, as Windows Defender is as well used in Windows 8/8.1).
-
kernel data inpage error spaceport sys
Hey
I just got a new pc, and whenever I stopped and it starts up again, I get an error: kernel data inpage error spaceport sys
and the computer just start windows normally.
What to do / how to fix it?
Good morning Martine.
For more information, see the error below:
-+------------------------------------------------------------------------------------------------------------------
7 has error checking, {fffff6fc40009b08, ffffffffc0000185, 1 c 2042860, fffff880013617ec}
GetPointerFromAddress: unable to read from fffff80151b76170
WARNING: Unable to verify timestamp for win32k.sys
ERROR: Module load completed but symbols can be loaded for win32k.sys
Probably caused by: memory_corruptionFollow-up: memory_corruption
---------0: kd >! analyze - v
*******************************************************************************
* *
* Bugcheck analysis *.
* *
*******************************************************************************KERNEL_DATA_INPAGE_ERROR (7A)
The requested page of kernel data could not be read in. Usually caused by
a bad block in the disk controller or paging file error. See also
KERNEL_STACK_INPAGE_ERROR.
If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
This means that the disk subsystem has suffered a failure.
If the status of the error is 0xC000009A, it means the query failed because
a file system has failed to move forward.
Arguments:
Arg1: fffff6fc40009b08, type of lock which took place (1,2,3 or PTE address value)
Arg2: ffffffffc0000185, error state (state code of e/s normally)
Arg3: 00000001c 2042860, the current process (virtual address for the lock type 3 or PTE)
Arg4: fffff880013617ec, virtual address that could not be paged in (or PTE contents if arg1 is a PTE address)Debugging information:
------------------Error_code: (NTSTATUS) 0xc0000185 - peripheral of e/s reported an IO error.
-+------------------------------------------------------------------------------------------------------------------
It seems that you have a bad hard drive or RAM module in your new system (ran 6 hollow landfill WinDBG), since it is a new system, I would bring her to the store you bought and let replace it.
Read this guide on how to test your RAM Modules: http://www.pcadvisor.co.uk/how-to/pc-upgrades/3432631/how-check-for-bad-ram-modules-in-your-pc/
Read this guide on how to test your hard drive: http://pcsupport.about.com/od/toolsofthetrade/tp/tophddiag.htm
Personally, I'd suggest to return the computer to the store and allow them to correct the problem, apparently not driver related to me (especially if you updated all..), it seems that you have a malfunction of the equipment.
You can try and run CHKDISK (http://windows8themes.org/how-to-run-chkdsk-in-windows-8.html), but I suggest you RMA your system and let check the RAM and hard drive.
If however, you want to ensure that it is not Windows, then reinstall Windows and see if the problems come back, but I bet they will be.
I know this answer might not be what you want... but...
Yuri
Maybe you are looking for
-
Qosmio PQG31A motherboard graphics controller
Hello I have a Qosmio G30 PQG31A and the graphics controller / GPU is dead! can someone tell me if there is a Toshiba repair center in East Sus *.
-
Re: Account Satellite S70-B-10Z 2 HDD bays?
Hello, can someone tell me if the Satellite S70-B-10Z has 2 bays for hard drives? Thank you!
-
Axis changes after a set interval
I have change my X axis range programmatically in various circumstances in my program. After the range changes, the method, and then calls another method to plot data. However, when I get the new method, the new range now has what I set the minimum o
-
I have a Dell Inspiron 531, I can't Panda titanium to download when I put in the disk drive. Why the habit of this work? I don't have an error message, but my computer says that there is a threat in my computer.
-
The written warning "Once completed, you must activate your device wireless to continue to send and receive e-mail messages and use other services of blackberry. If you do not want to continue, click Cancel. What does this mean and maybe why I do not