Pavilion 500: Not the Windows partitions?

Similar Questions

• Must regularly restart the DHCP Client - HP Pavilion 500-205 DT - Windows 7

  HP Pavilion 500-205 DT - Windows 7 Home Premium 64 - bit SP1

  Realtek PCIe GBE Family Controller - pilot 7.67.1226.2012

  Bought 3 identical machines for our daycare. Set up the same. All work fine except ONE of them becomes inaccessible periodically (every day more or less) on other computers on our small LAN-to-peer Windows. You can see, but cannot access any shared folder. To access OTHER computers on the local network of it there is NO problem. All 3 machines have the same profile sharing, workgroup, permissions, AV, firewall, all settings. I realized by restarting the computer solved the problem immediately but temporarily. I reduced to restart the DHCP Client service. Do all works well immediately, but temporarily.

  I tried the things:

  Call support HP - not useful at all. It is under warranty.

  IPv6 disabled

  Disabled wireless

  Disabled network card stopcock energy saving

  Definition of recovery CLIENT DHCP on:

  First failure = restarting the Service

  Second failure = restarting the Service

  Subsequent failures = restarting the Service

  Reset Fail Count after = 120

  Restart the Service after = 0

  But again, this is not the case for other machines with the default settings. Nothing works except the Client DHCP service is restarted. Loss of access occurs with or without someone connected or using it. It has happened since its first establishment.

  I don't know if the HP warranty covers the OS loaded at the factory. I don't want to restore the thing and start over. I'm not a Pro, just the guy in the office who did these things, but it seems that the network card may be faulty. I don't know if I can convince a person of first level support phone to have me bring the machine in an approved place.

  Any help greatly appreciated,

  Larry

  HP sends a FedEx box to put the thing in picked it up. I'll mark this resolved thing. Thank you all for your comments!

• Repair of bootcamp after having extended the Windows partition

  Hallo

  I have a Mac with windows on it.

  I expand the partition for windows, first by spreading 10 GB of mac, I don't then open windows and look for the 10 GB he wanted, but could not open windows, the error occurring has been 'missing in operation.

  When I use the following solution:

  sudo fdisk e/dev/disk0s4

  p

  setpid 4

  07

  Pavilion 4

  p

  To write

  There

  After "sudo fdisk e/dev/disk0s4" it says "resource busy".

  When I try to active the disk and partition in the windows repair utility, its says 'ACTIVE kan only be used on disk MBR.

  Sorry for my bad English, I really hope that someone can help you.

  What you are attempting is not supported by Apple - Boot Camp: resize the Windows partition .

  Can you post the output of the following Terminal commands?

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

• Cannot use the Windows Partition

  So, I have seen very similar messages and followed several forums, but I can't yet figure out what to do next.

  I have 8.1 Windows on my Mac.  I wanted to repartition the Windows partition and make bigger it because I was running low on space, and the Windows partition is what I use it mostly for graduate studies.  About a year ago, I took an easy youtube video and used Mini Wizard Partition re-partition space and it worked perfectly.  I have found the same video and tried to repartition the Windows partition again, but apparently I royally screwed up.

  My BootCamp is not yet visible more in disk utility.  Under the partitions, there is an option called "disk0s4" greyed, but I'm not allowed to do something with it.  I can't verify or repair.  If I go to Applications, BootCamp Assistant is there, but he wants me to start the installation of BootCamp.  It was not an option to restart Windows more, and when I turned on with alt + market, Windows was not an option more.

  I followed this tutorial:

  http://nerdr.com/bootcamp-partition-lost-repairing-Mac-partitions/

  and when I restarted my Mac, restart Windows was an option. So I thought that I fixed it! EVIL.  My screen was black and said: 'Missing Operating System '.

  I downloaded EaseUS Data Recovery Wizard for Mac (because it was another suggestion), and I was able to recover and see the files on the NTFS disk0s4, so I'm quite positive, they have not all been completely erased.  Or at least the part of basic Windows is still there.  I can't recover the drive to anything, because it tells me that I will just be fitness on the same drive, and I honestly don't know how to retrieve these files will help with the side of the partition of things.

  I also used TestDisk and it seemed to find my missing partition, but in the middle of analysing it, it says something like "disk too small."  After further research, I went through and took only the most recent score that seemed to be deleted with NTFS, and when you are trying to do, it would allow me to make a 'logic' partition because he said something in red, as 'bad file.'

  My Mac still works perfectly, but I'm terribly need to recover my windows.

  Here are my findings from a similar position:

  Last login: Wed Mar 9 16:30:28 on ttys001

  Anna-Owenss-MacBook-Pro: ~ acowens1$ sudo gdisk/dev/rdisk0; "exit";

  GPT fdisk (gdisk) version 1.0.1

  WARNING: Open with shared lock devices will not have their

  table partition automatically reloaded!

  Scanning partition table:

  MBR: hybrid

  BSD: absent

  APM: absent

  TPG: present

  Found a valid GPT with hybrid MBR; using GPT.

  Command (? for help): p

  Disk/dev/rdisk0: 625142448 sectors, GiB 298,1

  Logical sector size: 512 bytes

  Identifier (GUID) of disc: 0000429B-368F-0000-CB2D-000003440000

  Partition table contains up to 128 entries

  First usable sector is 34, last usable area is 625142414

  The partitions will be aligned with the boundaries of sector 8

  Space free total is 277435021 areas (132,3 GiB)

  Starting number (sector) end (sector), Code name of size

  409639 40 1 200.0 MiB EF00 EFI system partition

  2 409640 268314855 127.7 giB customer AF00

  3 268314856 269584391 619.9 MiB AB00 Recovery HD

  4 547018752 625141759 37.3 giB 0700 BOOTCAMP

  Command (? for help): r

  Recovery/processing command (? for help): o

  Size of the disk is 625142448 areas (298,1 GiB)

  MBR disk identifier: 0x0000711C

  MBR partitions:

  Code of State sector Boot start end sector number

  1 1 547018751 primary 0xEE

  2 * 547018752 625141759 0 x 07 elementary school

  Recovery/processing command (? for help): h

  CAVEAT! Hybrid MBRs are flaky and dangerous! If you decide to not use one,

  Simply press enter at the prompt below and your partition table MBR will be

  be intact.

  Type one to three GPT partition numbers, separated by spaces, to be

  added to the hybrid MBR, in order: 2 3 4

  Partition of EFI GPT (0xEE) place first in the MBR (good for GRUB)? (Y/N): y

  Create entry for the #2 GPT partition (partition MBR #2)

  Enter a hex code MBR (default AF): n

  Set the bootable flag? (Y/N): n

  Create entry for the #3 GPT partition (partition MBR #3)

  Enter a hex code MBR (default AB):

  Set the bootable flag? (Y/N): n

  Create entry for the #4 GPT partition (partition MBR #4)

  Enter a hex code MBR (default 07):

  Set the bootable flag? (Y/N): y

  Recovery/processing command (? for help): o

  Size of the disk is 625142448 areas (298,1 GiB)

  MBR disk identifier: 0x0000711C

  MBR partitions:

  Code of State sector Boot start end sector number

  1 1 409639 primary 0xEE

  2 409640 268314855 primary 0 x 01

  3 268314856 269584391 primary 0xAB

  4 * 547018752 625141759 0 x 07 elementary school

  Recovery/processing command (? for help):

  Now, my major dilemma is that in the original post, he said to the partition of the hybrids with the numbers of 3-4-5, but I was unable to do so.  When I tried 5, he said "partition does exist or is too large."  So I used the 2 3 4 numbers.  Now, I'm at the point where I use the w command (to write), but I don't want to do it if I didn't the other steps correctly.

  1 mini Partition tool is very dangerous and should never be used on a Mac, in particular, more than once.

  2. article NERDR is the most irresponsible article about these issues and causes and exacerbates still more data loss.

  3. Please do not rewrite the MBR/GPT with Gdisk.

  4. you must return to Testdisk. TestDisk is used only for scanning, not for the updates. All updates using Gdisk, not binding Testdisk, once the right partition headers have been found.

  5 Please after the release of

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

• Can I shrink a logical drive and not the extended partition to a bare metal restore to a smaller drive?

  The current configuration is a Dell T310 with a S300 controller, with all locations 4 hot filled with SAS drives.  The operating system is SBS 2008 (2008 Server/Vista), I intend to change the controller of S300 (software) controller, a controller (hardware) H700.  My concern is that the H700 brings readers a little smaller in size.

  The typical arrangement of Dell's diagnosis, followed by a recovery partition partition (E :), followed by the system partition (C :), followed by a partition with a logical volume (d).  If I use Diskpart to shrink the D: 'partition', he let me with free space, not allocated.  Thus, it effectively reduces the logical drive, and the extended partition stays the same size as it was, with no way to reduce it.

  The question is, if I shrink the logical D: drive and not the extended partition and then get backups of the system, I'll be able to a bare metal restore on the smallest virtual disk of the H700?

  That's what I did:
  -Released the S300 controller and 4, 450 GB, 15 000 rpm Cheetah RAID-5
  -Replace the controller H700 and 2, 2 TB 7200 RPM in RAID-1 Constellations

  Results:
  -Eliminates the possibility of falling on a disk space issue when restoring
  -Increased the amount of available disk space.
  M ' left with 2 free hard drive for future expansion bays.

• is not the window Defender sufficient virus protection?

  Windows 7 repeat myself that I should get antivirus protection... is not the window Defender sufficient virus protection?

  No, Defender (on W7) by itself is not enough. Get an AV package as well. There are a lot of those who are free to choose to include MSE.

  Note that if you install MSE, it replaces the defender and defender will be disabled.

  PS - Defender on W8 is not the same as the Defender on W7

  
  

  
  

  More info - https://en.wikipedia.org/wiki/Windows_Defender
  

• HP Pavilion 500-164: the printer error HP Pavilion 500:511 - CPU fan not detected

  I have a HP Pavilion 500-164. Every time I start it, I get a 511 - CPU fan not detected error message.

  At the bottom of the screen, it says F1: Boot

  Then he begins to run smoothly. It becomes annoying.

  Examination of the aircraft, but when I find the two fans running?

  What is the problem and what I take in repairs?

  Hello

  Use a can of compressed air to clean any dust from the fans in the PC.  With the side panel, power on the PC and still observe the rotation speed of the fan.  What do you see? slow, medium, or high speed?

  Open the windows to RUN and enter: MSINFO32

  What level of your PC BIOS runs?

  Install the latest diagnostics for your PC. Start your PC and press ESC then F2 to run a diagnostic.  Run a complete set.

• Pavilion 500-307nd: create additional partitions without endangering the recovery option

  I just bought a new HP pavilion 500-307nd, it has a 2 TB hard drive. Currently, it contains the recovery partition (10 GB), the rest is used as one and only one primary partition. I would like to divide this (close to 2 TB) a partition into three partitions: a primer containing the system and software, two for the storage of data only. The recovery partition will remain intact. That would be a problem? I'll always be able to use the if necessary recovery partition?

  Bart, welcome to the forum.

  Here's a guide that should help you.  Before you begin you must make a backup of all your personal data.  If you have not done so, you should do the System Recovery discs for the computer, too.  This will allow you to recover the computer if you have problems creating the partitions.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion 500-002ec: the HP Pavilion 500-002ec gpu upgrade

  Hello.

  I have a HP Pavilion 500-002ec pc and I want to replace the pre-installed gpu (Radeon HD 8570). I was looking at GTX950 and I have a few questions. I need more power for her? If so, how much more? And it is even compatible with current pc? Thanks for your replies.

  Hello

  If do the 950 GTX specific and model does not require a 6-pin auxiliary power connector then it should work. However, most of the GTX 950 require an auxiliary power connector 6-pin and the HP 300 watt standard power supply in your PC doesn't have that connector.  You would be obliged to replace the power supply or try the NVIDIA GTX 750.

  If you decide to stay with the GTX950 then I suggest you one of the following blocks that will give you a bit of room to develop and/or use a graphics card more large: Corsair CX500, CX600 or CX650m

  Be sure to measure to ensure that the graphics card fits will fit inside.

• Desktop HP Pavilion 500-342nem: can I upgrade my desktop computer hp pavilion 500 with the graphics card AMD RX 480 replacing edge R7

  I plan to upgrade my hp pavilion 500-342nem, who was already A7 graphical 240 with the new 480 RX.

  Is it possible to upgrade both the power supply and graphics card?

  There will be no problem of compatibility (PSU Corsair CX 500 questioned?.)

  I heard a lot of chatter on hp restricting the upgrade of their pc.

  The new card will work?

  Any help will be apppreciated.

  @Jeffrin98, welcome to the forum.

  I cannot find the specs of the product to the computer.  So, here's what you need to do.  Press Start + R from the view of the office.  This will open a run dialog box.  In the box labeled type msinfo32 opened.  In the page that opens, check the option titled Mode BIOS.  If he says UEFI motherboard is supported by the video card.  If this isn't the case, you will not be able to move forward.

  The next step is to measure the space where the card will be installed to ensure that it fits.  Measure from the back i/o port to the front of the case.  This will allow you to see if other ingredients will limit the installation.

  The CX500 Corsair power supply (PSU) should work.  However, check how much power requires the video card.  It may be better to buy a PSU with 600W.  High power will be used during peak power needs.  In addition, the card may require additional power connectors.  Also, I recommend a modular power supply.  It allows you to use only the cables that are absolutely necessary, create better air circulation.  It is very important with more powerful graphics cards.  The heat can be much larger.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP pavilion 500-023w (installing windows 7 questions)

  I just bouth HP pavilion 500-023w desktop PC recently.  It was pre installed windows 8. I tried to install windows 7. Finally, I installed windows 7 but I need the software drivers for my "HP pavilion 500-023w.

  I tried to download HP Web sites, but these drives only work for windows 8.

  So he will be busy if someone can give me the software drivers links that works perfectly on windows 7 for my "HP Pavilion 500-023w".

  Faisal

  Hello

  No, now, try this:

  http://ftp.HP.com/pub/SoftPaq/sp56501-57000/sp56998.exe

  Kind regards.

• Windows 7 - Aero Peek window previews flicker when displayed not allowing not the window selection.

  When I move my mouse over one of the icons in the taskbar much of the time it will not display the Aero peek for windows previews. When he does it usually blinks for a few seconds then does not appear. The odd time, keep it visible it will allow me to get an overview of the windows by bringing to the forefront through one of miniature windows flying over my mouse but when I click to select a window it goes back to what I was on earlier. In the case of multiple windows of the same type, for example to say Firefox and download manager in firefox by clicking on the firefox icon in the taskbar is nothing, until I navigate to and close one of the two windows manually. It became a major problem with my daily use of my computer so much so, in fact, that I returned to the use of Linux Mint during the bulk of my computer daily as it does not take me an excessive amount of time to navigate between windows. If anyone has suggestions as to how this can be fixed it would be much apreciated and would allow me to start using Windows 7 even more.

  I tried to run the troubleshooter several times with no results yet. The driver is up to date and working properly, I tried unintsalling, restart and reinstall the driver 64-bit Windows 7, with no change in the problem. I can try a reinstall of Windows 7 because it won't cause a lot of data loss with separate OS and partitions of data.

• AlienRespawn detects is not the recovery Partition

  I'm going to be upgrading to an SSD and was to check what are my dining options on my M17X r3 laptop.

  When I open AlienRespawn but, I see an error that AlienRespawn was not able to detect the recovery Partition.  It's may be missing or damaged.

  He said so to recover your computer to the original factory condition and restore the recovery Partition.  Use your system recovery discs.

  I have a backup of the laptop, but I don't know whether or not they are recovery disks.

  I checked, and Windows does not detect the RECOVERY volume.  The State is healthy (System, active, primary Partition).  Capacity free 19.53 13,16 GB space.

  That seem correct?

  I can do to help the AlienRespawn find the partition, or I have to use a different process when it's time for a reinstall?

  Thank you!

  I did everything above, and he always had the same error. I then notice in the free version, it will not creat a new backup so I bought the premium and it works now.

• HP Pavilion 500-311no: the hp Pavilion 500-311no upgrade

  Hp Pavilion 500-311no desktop PC, I bought a few years ago and now I feel like I would get some more power out of it then is it possible to upgrade this computer. I use mostly this pc for a game so what I'm looking to upgrade is the gpu. It seems that the motherboard supports the latest grphics cards and I think they should also fit the case. Incase of replacement parts, the power supply needs to be replaced probably as well. Also overclocking motherboard support and how the overclocking and replacement parts affect warranty?

  Greetings,

  You have some positives on your side:

  PCIe available x 16 slot 3.0.

  UEFI BIOS.

  Your chassis will limit the duration of the update of the graphics card.

  You have only a 300 Watt power supply.

  Most of the HP motherboards cannot be overclocked. I have a processor Intel 4820 K. HP offers limited overclocking abilities with this processor.

  Check the measurements on the existing power supply.  A diet of 600 runs most new graphics cards high-end. NVIDIA cards tend to require less energy than equivalent AMD cards.

  Check the height of the rear panel input/output where the x 16 slot is to determine the maximum length of a new card.

  Shop for a new card graphics and power supply when you know your limits. The high-end cards are usually double slot. Make sure you have room to install a card double slot. You need to be able to burst a second plate of input/output rear panel to install a dual slot graphics card.

  Modular power supplies reduce tangles of cables in the chassis.

  See you soon!

• HP Pavilion 500-550nv: the upgrade of power

  Hello. I have HP Pavilion 500-550nv (in which case is microtour format) and want to upgrade my HP power which is only 180 W!

  I want to know what brand of food is supported for my pc model (hp pavilion 500-550nv) and how much wattage recommended (up to 600? up to 650?). Which is the recommended limit of power supply of power for my HP?

  I'm waiting for your answers. Thank you

  Hello @jeandoumpier,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I read your post on food and wanted to help you!  I understand that you are concerned about upgrade options.

  You should be able to improve the power you want.  The Office should take but a lot of power, it must, food that is installed.  Just check that the power supply to use, firmly enters the tower.  Based on the Specifications of the product, you can find the dimensions tour here:

  • Height: 36.7 cm (14,48 in.) unpacked

  • Width: 17.5 cm (6.91 inches) unpacked

  • Length: 38.9 cm (15.35 inches) unpacked

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!