Pavilion dv7-4270us: dv7-4270us bluetooth does not work after driver update

I recently updated my drivers from the HP website.  Now, I know it was a mistake that bluetooth has not been installed correctly.    And there is no option "driver restore.  I tried several times sp50180, according to the HP website and also tried the old version listed (sp49153).   They old version did not install correctly and a new seemed especially, but none of my Bluetooth devices that used to work to do now.   I can 'connect to' some devices but they cannot transfer photos, connect to the audio, etc.  Some devices that are used to work can still be seen when I say "add a bluetooth device".  After installation, in the Device Manager, I find the following:

The radio Bluetooth: Bluetooth Broadcom 2070 and Microsoft Bluetooth Enumerator (both working properly)

Human Interface Device: Bluetooth Remote Control (works)

Modem: Modem Standard via a Bluetooth #2 link (works)

Network cards (all working correctly):

Device Bluetooth (personal area network)

(Heading RFCOMM Protocol TDI) Bluetooth device

(and my other network devices, all functioning properly also)

Other devices: this is the problem area.  After installation and reboot, I always find myself with 10 entries "Bluetooth Peripheral Device", all with a yellow exclaimation mark and all say real estate "Other devices", "unknown" (GSM) and the location is "on Microsft Bluetooth enumerator". "."

I tried right click and uninstall it, but when I reboot they come back to the top, search windows update, but can not find a driver and go straight to the "other devices".  I also tried to uninstall the "Broadcom 2070 Bluetooth 3.0" 'Programs and features' and right-click to delete each listed above bluetooth driver and then run the sp50180 again and it will install without error and find the same above drivers that work and leave the same 10 does not.  And my Bluetooth headphones (two different ones) is more work (or can be seen) and my Bluetooth phone can be 'connected' but any attempt to transfer fails.

I've exhausted all ideas on the web, I could find, and none have helped.  I tried to load a restore point, but after having so many pilot facilities, there is no point of restoration with the appropriate driver.  A full backup of the system on another drive, but much changed the applications and data files so I cannot restore it.  Unless someone knows how to use a full backup of the Windows 7 system to restore only the Bluetooth driver.

Another idea is that the driver update that messed up things maybe changed some other file or a registry setting that is not corrected by sp50180, but that seems unlikely.

Is it possible to manually install each of the 10 'other devices' drivers?  If I right click on a defective device and select "update driver software" no matter if I select the drive C:\ or F:\ (my driver and software download drive) or automatic search (including online) - it does not find the driver files.  I also tried to select properties and 'put to day driver' but the same results.

Any help would be greatly appreciated.

I found a solution. I received a call of support in Mumbai.  HP gave me a free call because they were not able to set a guarantee repair questions, so gave me the free support call.  I took an hour, but ended up the solution was very simple.

There were these problems:

1) 10 'other devices' in device with the exclamation points Manager can be uninstalled, but still were automatically reinstalled with the same exclamation point.  No pilot was available to the public for them.

(2) my phone under Bluetooth devices could connect but would not photos transfer.

(3) neither my helmet Bluetooth would not work.

The solution was simply to go to 'Show Bluetooth devices' and right-click on each and select 'Delete device' (even if dimmed they might still be revoked).  After all have been abducted there were no "other devices" in Device Manager.  I then added each Bluetooth device again.  This was very well all work.  I also noticed my phone was five drivers "Bluetooth Device" was so 5 of the 10 exclamation points himself.

For some reason, deletion of the driver in the Device Manager has not deleted the list "Bluetooth Device".  And by uninstalling and reinstalling the drivers, it does not work.

If the answer is simple.  Before removing the drivers Bluetooth first remove all Bluetooth devices.

Tags: Notebooks

Similar Questions

  • HP Pavilion dv7: RealTek Cardreader does not work after upgrade to Windows 10 10

    After the upgrade to Windows 10 64-bit of Windows 7 64-bit, the Realtek PCIE card reader does not work.  Device Manager showed initially a card reader driver error, but after the reboot, I can not find an error or the device itself.

    Any ideas would be apprieciated.

    Hello:

    See if the driver installation of W10 directly from Realtek card reader solves the problem.

    First driver on the list...

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  • Pavilion 17-e110nr: bluetooth does not work after last update 8.1 Pavilion 17-e110nr

    After I noticed the bluetooth does not after the upgrade - is not seeing the same on Device Manager. I got actually work once - can't remember where the driver came - and then pushed hp a new driver ralink and it is not worked since even though I tried several things, including the direct download of mediatek. I have a Ralink RT3290 802.11bgn Wi - Fi adapter and just need a driver that works. I think I have about 4 separate batteries bluetooth now - can be part of the problem - but the most recent came from hp. help, anyone?

    solved myself. disabled norton antivirus and firewall and reinstalled and it worked. Hooray!

  • Epson v500 Scanner does not work after driver update!

    I recently bought a V500 photo and scanned my first 35mm using Epson Scan v3.7.4 negatives. The colors seemed off so I download and installed the latest v3.7.7 of support to Epson.ca hoping that it might help.

    Following the upgrade of the driver, the scanner has stopped working! Loads of Epson Scan, but after 5-10 seconds, I get the message: "no response from the scanner. Make sure the scanner is turned on and connected properly. If you use the transparency feature, remove the reflective document mat. »

    Then I restored the latest install w / restoring Windows but still could not get the job to scan. I drove back to the pre - Epson scan install date and tried to reinstall the earlier version but still no luck to get scanner work.

    I then followed the steps of uninstall on the Epson.ca support site removed all the drivers and the software with the scanner turned off and unplugged. Then I reinstalled the old version of Epson Scan of the CD because he had worked at the start. I reconnected it the scanner it plug it in and turn it on. But it still does not work! Ditto for uninstall and reinstall with the latest drivers.

    Notebook P7350 using Windows 7 32 bit SP1. Scanner is connected directly on the laptop, not through a hub. I tried all 3 ports USB in the hope one would work, but no luck. All connections between the pc and the scanner seem robust.

    Any suggestions to get scanner work?

    Thanks for the reply of adeline. In the meantime, Epson come back to me when I contacted them again but only after I have disabled cookie blockers in Firefox when visiting their support site. The first time I've done this, and the support form has not sent correctly.

    It turns out that the scanner must be completely turned off and unplugged then reconnected after that driver installed. I discovered one of the records was not too tight that it should have been :-0 if I was sure I had checked it earlier.

    Thanks again.

  • Satellite L750 - Bluetooth does not work after BIOS update

    I am preparing some L750 notebooks for use and accept updates from the Toshiba, which included an upgrade of BIOS v1.70 for v2.00. He appears after this update occurs that Bluetooth no longer works, i.e. try to install Bluetooth Toshiba stack will fail as it is said that the Bluetooth radio is disabled and must be turned on for continue.

    As the L750 (model PSK1WA-0C300R) is not a hardware switch to enable or disable the Bluetooth/Wi-Fi, the only option available (Fn + F8) is unsuccessful. I ran a recovery of factory default installation and Bluetooth still does not - resumption of classes does not restore the BIOS to the previous version. I have 5 of the model and confirmed the update of the BIOS is the cause. Two laptops now have v2.00 and Bluetooth has been tested in the work before the update of the BIOS.

    If Bluetooth is not critical for the environment which I deploy these notebooks, it's an annoyance I want to solve. My questions are: has anyone encounter the same problem and managed to resolve it? Is there a BIOS v1.70 available for download to restore the functionality? Y at - it an update of the BIOS > V2.00 for solve the problem I have? Thank you.

    Hi JasonL750,

    Load default settings after updating the BIOS? Go into the BIOS, press the F9 key to load the default settings of the installation. Also, make sure that Bluetooth is enabled in the BIOS if there is such an option.

    In addition, it would be interesting to know what happens if you use the FN + F8 key combination. Don't you see that he has an option to turn on Bluetooth and if so what happens if you do this?

  • Pavilion x 2 N005TU: ELAN touchpad does not work after windows update 10

    Hi, I've just updated my Pavilionx2 N005TU for windows 10 yesterday. After update, tochpad is not working and keep turn off every time, even I allow him - he'll be disenabled after closing. And I have to activate whenever I turn on my laptop. You have a permanent solution for this? Thank you.

    PS. I already checked for the new update of device - but no update to touchpad so far.

    Hi Amm_S04, as you know windows 10 has just come out, so it will take time for all drivers (including touchpad drivers) to get the new updated version supporting this new windows. For now you can also check here http://support.hp.com/us-en drivers

    Although I would advice you to wait and update the driver through windows update as soon as it is available.

  • P0R94EA #ABU: brightness and HDMI does not work after driver update

    Hello

    I get a notification to update my drivers for HP Support Assistant that I took and I installed all the drivers involved and since that I can't not change the brightness of my screen or use the HDMI for display on my TV. I don't have the updates has been "Intel high definition (HD) Graphics Driver.

    Can someone help me with this please have tried different things from other sites, but nothing has worked.

    Hello

    Is there an improvement if you install the earlier version at the following link?

    http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72107.exe

    Kind regards

    DP - K

  • S3-391 Acer wireless network adapter does not work after driver update

    Hi, I have an Acer Aspire S3-391 running Windows 7 64 bit and I have recently updated my card (Atheros AR5BMD222) wireless network to the latest version of such 10.0.0.274 as recommended by the Acer site.  After updating the driver, I can no longer connect to my wifi at home.  When I try to connect, I get the message that no wireless connection is available (even if all my other devices can see the wifi network) and when I diagnose the problem, it is said that there might be a problem with the wireless network card and that windows could not automatically bind the ip stack Protocol.  I tried to uninstall the new driver and reinstall one old and running a system restore before installing the new driver, both with no luck.  When I try to manually configure a wireless connection, I get message "an unexpected error has occurred."  I have an automatic DNS and IP address, and when I look at my ipconfig, IP, DNS, DHCP, etc all have addresses.  Any help would be greatly appreciated, thank you.

    And while playing, I managed to fall on a solution.  When I looked at the properties of my wireless network card, I have disabled NetBIOS over TCP/IP and now everything works fine.

  • my phone does not work after last update itunes on my phone connection with my pc, it shows only i tunes icon and the application of itune on my pc does not work

    my phone does not work after last update itunes on my phone connection with my pc, it shows only i tunes icon and the application of itune on my pc does not work

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    Once iTunes to work properly, you should be able to fix your device.

    TT2

  • AutoFill does not work after last update 3-6-3

    AutoFill does not work after last update 3-6-3

    is after update

    See control if Firefox automatically fills in forms

    Start Firefox in Firefox to solve the issues in Safe Mode to check if one of your modules is causing your problem (switch to the DEFAULT theme: Tools > Modules > themes).
    See the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems and troubleshooting questions with plugins like Flash or Java to solve common Firefox problems

  • my super USB does not work after last update OS EL Capitan

    my super USB does not work after last update os el capitan

    Hi viral_02,

    The resources below provides a few for the SuperDrive USB troubleshooting steps.  Click on the link to see all the possible symptoms and solutions, including resetting the system management controller.

    Get help with the SuperDrive slot on your Mac computer loading

    If the problem persists, Contact Apple or an provider of services authorized Apple, or make an appointment with an Apple Retail Store additional diagnosis, evaluation, or service.

    Take care

  • RDP does not work after the update of the virtual machine tool

    There are many machines these RDP does not work after last update VM tool.

    Hello

    Please replace RDP linked DLL file from any server to work from the same version of the OS...

  • Bitmoji keyboard does not work after last update iOS 10

    My Bitmoji keyboard does not work after that I updated to iOS 10 update. I have no idea why, my friends Bitmoji keyboard works fine after that she has updated her phone and mine does not work so I was wondering why. It worked perfectly fine before I upgraded my phone. I was wondering what to do.

    the same problem. He repeats to me go to keyboard settings and make sure that it says allows full access to Bitmoji and it does. Should not have upgraded to iOS.

  • Satellite Pro C850 does not work after Bios Update

    My satellite pro c850 cd does not work after updating the bios of toshiba.

    What should I do?

    Saying: don t work do you mean it does not fuel upward or what do you mean exactly?
    Flash the BIOS correctly?

    Maybe something went wrong during the upgrade, which means that l ROM flashed module isn't properly

    In most cases a special disc of crisis of the BIOS would be required to operate
    Not sure if you can get it repaired by your own
    Check this thread. Maybe this helps:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59637

    Otherwise you need help of the authorized service provider available in your country.

  • Satellite C50D-A-12 x - touchpad does not work after Windows Update

    the touchpad does not work after the windows updare

    I always recommend you read other threads / messages and spikes before considering opening new thread in the forum
    https://Forum.Toshiba.EU/showthread.php?82878

Maybe you are looking for

  • Restore the menu in the menu bar drop down Bookmarks

    I have reactivated the menu bar, but the bookmarks entry is absent, could someone tell me how to get it back? I am aware of the icon drop-down bookmarks menu and do not want to use it.

  • Replacing the drive HARD on Equium M50-216

    Hello I'm looking into upgrading the hard drive in my M50-216, which currently has a MK4026GAX. The player that I am most interested is the MK8032GAX. Is this a suitable replacement, that is going to work? A few questions: 1. I guess it's just a case

  • BlueScreen (Windows 7)-Satellite L650

    Bluscreen of death has occurred once every day for a week. I have a new (1 month) Toshiba Satellite L650 with the following details; Intel Core i5 2.5 GhzWIndows 7 Home Premium 64-bit4.0 GB RAM1.8 BIOS versionA lot of available memory Software - Offi

  • I forgot my password to icloud how can I change the password please help

    Hello team Please help me I use apple 4S and I forgot the passward of my cloud i How can I reset it. I read your conversation on this subject but in my phone does not show sing option so how can I remove the password and id

  • printing from Mac to HP Laserjet 5100 dtn without internet

    Hello I have a Mac Book Pro using OS X 10.5.8 and a HP Laserjet 5100 dtn. There is no Internet in my room. Is it possible to send files using an ethernet straight cable on my printer? How can I print? Thank you for your help. Christian