Pavilion Elite m9200t: Light Orange lighting... No monitor activity

Similar Questions

• My pavilion dv2418nr wireless light stays orange

  My pavilion dv2418nr wireless light stays orange, you don't go to the Blue will not recognize the connections surrounding neighborhood.  ISP says that the router is fine, this is the switch of the laptop not allowing the card read wireless connections. HP tech told me plug Ethernet from the router to the laptop... I got on the internet very well... but it isn't a hard connect.  Anyone had this problem with their switch?  I think that until this little light turns blue, I have better luck.  Thanks for your help

  Hello

  Try a Hard Reset as follows.

  Shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the power button for a minute.  Reinsert the battery, connect the power adapter and start Notepad.

  Kind regards

  DP - K

  

• I have a Pavilion Elite M9150F and it seems that the ignition button does not work. The power light is on

  My Pavilion Elite M9150F P/N KC880AA-ABA running Windows Vista Home Premium 32 bit. The device turns on no switch or remote control. He lite is turned on and power is running through the unit until button (checked through AC voltage detector) are there known issues with these? Are there spare parts? It doesn't hang or move the last time it was turned on. What are my options? Thanks for any help.

  Hello cello6996
  
  You are in warranty? If so, I would suggest contacting HP. If you are out of warranty, follow the steps below.
  
  How does a power button is essentially that it shorts two special pins. This short film is a signal to the power on the power supply and all components. A quick Google search reveals the most common method to do this is to disconnect the wires to the pins on the motherboard power button and then tap a screwdriver against just these two pins. Use gloves as a precaution. or a screwdriver with an insulated handle.
  How to bypass the power on button on pc
  Is there a way to bypass the power switch?
  
  If the computer starts correctly something wrong with the power button. If the problem persists, it is more than likely a problem with one of the hardware components and the problem will have to be isolated further. Let me know what happens.

• Do I have reason to infer that I can't get two monitors running on my HP Pavilion Elite HPE - 410 t?

  I got the Pavilion Elite HPE - 410 t with the included nVidia GeForce 315 graphics card and tried to get two monitors put in place. I have two VGA screens and I run one of them off the coast of DVI using a VGA port to DVI, and it works fine. However, I can not all signals from the built-in VGA port, so I started to look around the site of HP. I came across a page that lists the motherboard Plug and he shouted that the embedded video is not available if a graphics card is installed.

  Thus, it seems that I am out of luck, but I just wanted to see if anyone could tell me if it is maybe something obvious that I'm missing. My nVidia monitors also has an HDMI port, but I understand that I would need a HDMI monitor to be able to use this port.

  Can someone let me know if I'm wrong in my understanding of my options, or if there is an easy solution?

  Thank you.

  Hello

  Yes, you are right to assume that if you have a video card installed, the integrated graphics chip is disabled.  Looking at the specifications of your card (see link below), he suggests that it has a VGA, DVI and HDMI connection.  However, I realize that these specifications vary and may not apply to the card that you have.

  NVIDIA GeForce 315

  If yours doesn't have the VGA adapter, then your also had reason to assume need you a monitor with an entry in order to use 2 monitors HDMI.

  Kind regards

  DP - K

• I have a HP Pavilion Elite m9060n desktop PC and want to have two monitors.

  1. I have a HP Pavilion Elite m9060n desktop PC and I have my monitor connected to my computer using the NVIDIA GeForce 8500 GT DVI - I port chart.  I want to use two monitors and on the back of the computer in dos I/O ports there is a VGA slot but there is a black top, lid that States do not remove.  This means that the port is not available?
  2. I have also a port HDMI as part of The NVIDIA GeForce 8500 GT can I use that and the DVI port on the NVIDIA GeForce 8500 GT to have two monitors?
  3. Can I use a DVI splitter with DVI-d port on the NVIDIA GeForce 8500 GT to have two monitors?

  NVIDIA GeForce 8500 GT

  

  

  1.I have a HP Pavilion Elite m9060n desktop PC and I have my monitor connected to my computer using the NVIDIA GeForce 8500 GT DVI - I port chart.  I want to use two monitors and on the back of the computer in DOS i/o ports, there is a VGA connector, but there is a black top, lid that States do not remove.  This means that the port is not available?

  YES, the white cover means that the port / ports are not available. Most HP consumer computers automatically disable the onboard graphics when a x 16 PCIe graphics card is installed

  2.i have also a port HDMI as part of the NVIDIA GeForce 8500 GT can I use that and the port DVI on NVIDIA GeForce 8500 GT to have two monitors?

  Yes, you can use the HDMI and DVI-channels simultaneously to support two monitors. Here are the specifications of your desktop HP Pavilion Elite m9060n. According to the specifications;

  1 - S - video *.
  2 HDMI
  3 - DVI - I (dual link) *.

  Supports two displays at the same time

  According to observers, you may be able to use your current configuration to drive two displays. You can use two HDMI screens with a HDMI and a DVI-HDMI cable. You can use two monitors DVI - D DVI cable with a DVI-HDMI cable. You can also use a monitor VGA and HDMI or DVI - D and VGA monitor with appropriate adapters and/or cable. Please provide the brand and models of two monitors for most accurate response.

  3. can I use a DVI splitter with port DVI on NVIDIA GeForce 8500 GT to have two monitors?

  N °

• HP Pavilion Elite HPE-510 t - two monitors?

  Hello forum!

  For work I'll put up a brand new, out-of-the-box, desktop Pavilion Elite HPE - 510 t series, and I'm supposed to put up with two monitors. The monitors are both monitors HP 21 "(not sure model number, but pretty sure this info is irrelevant.) Both monitors have a DVI and a VGA output each.

  The problem is... I don't know if the computer can get out to two monitors. I mean, I think it can its such a new computer and the plug about it being very respectable. But at the back of the system, the only entries that I see are:

  1 HDMI

  1 DVI

  assortment of 6 audio inputs (speaker, microphone, etc.).

  1 Ethernet

  4 USB PORTS

  and something audio optical

  But there is also what appears to be two locations that are "closed" for lack of another word. One is what appears to be a DVI input but with a screwed in black plastic piece. I guess I should remove the plastic and it would be an another DVI but on the plastic was the words "DO NOT REMOVE" so I left alone. The other location is what seems to be a HDMI slot with a black piece of plastic glued to the front.

  The computer is capable of ouputting to two monitors?

  and

  What are those waterproof slots?

  Good luck with your responses and thanks in advance,

  Rose_Parade

  rose_parade wrote: there is a second DVI input or a VGA at least that I can see.

  There's a HMDI.  Use a HMDI on DVI connector.  Not very expensive.  Make sure you have the right sex on each end or cable/connector.  See the Big Dave det-related article it upward.

• Running 4 monitors 1920 x 1200 on a Pavilion Elite I7 desktop PC (a double graphics - GTS 250 cards)

  Update (November 14, 2011): there is a happy ending at the bottom of this thread. In a Word, I needed to upgrade my 700W power and install a ~ XFX HD 6870 (AMD/ATI) $ 200 video card, connect 2 monitors to 6870's connectors 2 mini DisplayPort and connect the other 2 monitors to 6870's DVI connectors.

  In the original post, I went to get a second GTS 250 but I was able to do it with a single card.

  Original message:

  I have already noticed that my system (HP Pavilion Elite e9180f desktop PC) supports dual Nvidia GTS 250 in the thread next where I'm looking for advice for upgrading my system to 4 monitors:

  http://h30434.www3.HP.com/T5/desktop-monitors-and-video/how-do-I-upgrade-my-Pavilion-to-4-monitors/t...

  I need to buy a second card Nvidia GTS 250, but they are hard to find.

  The 250 GTS that came with the PC has 1 GB or RAM on it. I've only been able to find a 250 GTS with 512 MB of RAM above. Both cards will co-exist on my system if I can run 4 monitors?

  I'm tempted to just bite the bullet and order 2 new cards as the GTS 250 that I find can take up to two weeks to get.

  Can anyone recommend a modern replacement model for the GTS 250 (1 GB RAM) I can buy 2 and then installed in my machine (Elite e9180f) with a minimum of hassle?

  I ordered (and received) a new PSU POWER 750 watt and 3 additional monitors to 24 "(et un stand)."

  Thank you

  Because I'm a spread for the penalty, I went ahead and ordered the XFX HD 6870 and returned the XFX HD 6850.

  Only after you have installed the 6870 I realized this video card requires 2 PCI express power connectors. Of course, my stock PSU only has a PCI express slot so I went down to Staples and bought a power supply 700W (a RetailPlus PS700W). I installed myself (without the help of a technician that I had seen what the technician had to do when I hired one to try to replace the stock power supply with a Corsair 750W) and it worked. It was last Thursday and the machine works since then.

  The 3 HP ZR24w monitors I ordered came with a regular DisplayPort cable but I needed 2 Mini DisplayPort to DisplayPort cable. I have ordered them to my place of local parts (OEM Express) and they came today.

  I plugged praying them, and then they played.

  So to get 4 monitors running a single card, I had to put my diet to 700 watts, install a XFX HD 6870 (it's a Radeon ATI/AMD with 2 x connectors DVI, an HDMI connector and mini 2 DisplayPort connectors) and order 3 HP ZR24w monitors. 2 monitors should be connected via the adapter mini DisplayPort to DisplayPort Cables and the other 2 are connected via DVI.

  From what I can tell, HD 68 x series video cards can drive only 2 DVI monitors at a time and if you need at least 2 aswell able DisplayPort monitors.

• Pavilion Elite e9150t and monitor Dell

  Hello world!

  I'm new to this forum. Two months ago I bought the Dell S2209W 22 "full HD panoramic monitor. Now, I fell in love with Pavilion Elite e9150t and want to buy it but I don't know if the monitor plugs match e9150t. Any suggestion would be appreciated.

  Oldxxjohn, the monitor should work fine with the elite.  Monitor connectors are standardized to work with any brand of computer.  Here is a link to the "Product information" pages for the elite:

  http://h10025.www1.HP.com/ewfrf/wc/prodinfoCategory?LC=en&DLC=en&cc=us&product=4003103&lang=en

  Message edited by old_geekster on 07/01/2009 12:18

• HP Pavilion Elite HPE-400Y no video output.

  Hello

  I have a HP Pavilion Elite HPE-400Y computer that I had stored (unplugged) in a bedroom closet bedroom for almost a year.  It was working fine when I put it in storage.

  This past weekend, I wanted to use, so I plugged in and connected to an analog VGA monitor well known on the integrated motherboard video VGA analogue connector.  When I turned on, there is no video on the monitor.  I searched the HP support site and found a statement that said "built into the graphics card or the card PCI Express x 16 slot are usable at once; they are not usable at the same time. "This computer came with a 5450 PCI express X 16 video card installed.

  However, the 5450 PCI express X 16 video card only has a digital DVI and I wanted to use a loose analog VGA monitor.  So I powered it turned off and physically removed the 5450 PCI express X 16 video card.  Then I unplugged the power cord and removed the CMOS battery for a few minutes.  Then I replaced the battery and applied again to power.

  I still do not get all analog VGA video out of the motherboard, not even the BIOS messages it is first energized.

  I also tried to integrated edge connector with a DVI equipped, monitor.  Still, there is no video output.

  So I removed the power and re-installed the 5450 PCI express X 16 video card that has only a DVI connector.  I connected to a monitor DVI equipped and applied again to power.  There is still no video output was two well-known instructors.

  When I turn on the computer, the fan power works, processor and fans of casing run, the blue led on the switch is lit and not blinking.  The Green LED on the motherboard is on.  The Green orange and activity led Ethernet link light are on.  There are no beeps.  I can hear the hard drive starts to work.  I have no video output.

  I use a HP USB keyboard and a USB mouse.  The red LED at the bottom of the mouse is not on.  The shift lock and lock lights number do not light when you press the corresponding key.

  This computer has spent more time of storage that it has been used.  It worked even when stored in a bedroom closet in bedroom.  I checked all the wire connections on the motherboard, with no improvement.

  I would like any suggestions to get this working of the computer.  I wonder if the motherboard has somehow that went wrong.

  Thank you for your help.

  Hello Big Dave,

  Thank you for answering my question / problem.

  I am aware that I can not use an analog VGA connection on the motherboard for a digital DVI input on my LCD monitor and vice versa.  I tried two different montors both analog and digital connections on the motherboard.  I tried to communicate clearly, but I guess that I don't have.

  It is unimportant, now that I've found that HP recognizes that my computer model had a drawing or a manufacturing defect that causes the exact symptoms I am having.  There is here a link to HPs extended warranty program that describes the patterns and symptoms:

  http://support.HP.com/us-en/document/c03199423

• Request help second addition, internal hard drive [HP Pavilion Elite e9290f]

  Hello

  Quick question here. I am a music producer and you can always use a ton of extra space as some of my projects are 17 to 20 GB in size. My HP e9290f comes with a stock of 1 TB Seagate (I think) internal hard drive. I intend to add this DeckStar HGST hard 4 TB (7200 RPM)

  However, I am not sure, if this drive is compatible with my computer. I talked about the upgrade & maintenance manual but inside, he tells me only how to replace the current internal hard drive. The addition of this amount of space external hard drive is not an option since all my ports are used by external hard drive! Can anyone shed light on what tools I need exactly to connect this HD extra 4TB? I would appreciate your answers, because time is of the essence

  HP Pavilion Elite e9290f | Intel Core i7 920 2.67 GHz | Windows 7 Ultimate 64 - bit Edition. 20 GB OF DDR3 SDRAM MEMORY | 1 TB of HDD at 7200 RPM. HARD drive external 2 TB | HARD drive 1 external to | HARD drive 640 GB external | HDD external 500 GB | NVIDIA GeForce GTX 260 1.8 GB | Audio interface Edirol FA-101 | Samsung 2493 HM 24 inches. Wide screen monitor |

  Hello

  I have not tested a HDD 4 TB on the motherboard of truckee. In theory, it should work as a data reader set shaped like a GPT disk.

  Another option if you don't want to take the risk is to install two hard drives of 2 TB. The one in the location empty in the cage from the hard drive and another in the optical drive Bay (if open) second.  You will need one 3.5 "to 5.25" adapter if you use the optical Bay.

  Check on the return policy for the 4 TB harddrive and see if your can return/exchange it if it doesn't work.  Kit retail for Hitachi 4TB has an optional driver if the motherboard of your PC will not format the drive completely outside up to 4 TB.

  

• HP Pavilion Elite HPE - 400z CTO: H - RS880 - Μatx Motherboard BIOS Update caused crash, to see a black screen now?

  I have a desktop HP Pavilion Elite HPE-400z running Windows 7 (64), my computer was working fine, however I thought that I needed to update the drivers and things from the HP website.

  The first thing I installed was the following: H - RS880 - Μatx Motherboard BIOS Update

  That restarted immediately frozen mouse on a black screen. When I turn on the computer the lights and the fan turns on but the screen remains black. Their is nothing wrong with the monitor, it's light is on, but when turn light it just says: "monitor going to sleep".

  I went through these troubleshooting pages: http://support.hp.com/us-en/product/HP-Pavilion-Elite-HPE-Desktop-PC-series/4269972/model/4300925/do...

  http://support.HP.com/us-en/product/HP-Pavilion-elite-HPE-400-desktop-PC-series/4269972/document/BPH...

  without success.

  Any other suggestions of what I could do to fix this?

  Hello

  Disconnect the PC and press and hold power for 30 seconds. Remove and replace the battery CMOS. It's a $4 item. Now let's see what happens. If no joy, then try the steps above once again.

  If your PC support has been changed or modified then put it back in its original state.

• Pavilion Elite M9040N turns on or turns off continues

  I have a Pavilion Elite M9040N media center desktop computer and it began to turn and turns off constantly.  The fans, the DVD player and the power that all light turns on for about 3-4 seconds then it turns off for 3-4 seconds, then starts the cycle again.  Does not get the bios start and nothing appears on the monitor.  I changed the power supply hoping that was the problem but no luck.

  Anyone encountered this before?

  Anyone know what is happening?

  Thank you

  John

  Final update

  Thus, the slot and off tension of the issue was due to a fault on the motherboard.  In order to get what they functional system once again I have had to replace the motherboard and video card (I don't know why, but this card is not as well).  I also replaced both of the hard drives, upgrade to the C: 1.5 TB drive and a D: 2 TB drive and power.  I bought a new copy of windows 7 64 bit and did a new install and updated all the drivers.  I was able to transfer all of our data, photos, music, etc. among the old readers on the nine with an external SATA cable.

  I'm happy to be up and running again but in hindsight, I have pretty much rebuilt all of the computer.  I hope that this will last a few years.

  Thanks for all your help and suggestings

• HP Pavilion Elite HPE-575 has: the graphics card upgrade

  Hi I want to know if a GTX 950 oc 2gbddr5 graphic card is compatible with my HP Pavilion Elite HPE - 575 a pc, if someone can shed some light on this would be very appreciated

  @W1976, welcome to the forum.

  W1976 wrote:
  

  Hi I want to know if a GTX 950 oc 2gbddr5 graphic card is compatible with my HP Pavilion Elite HPE - 575 a pc, if someone can shed some light on this would be very appreciated

  No, the GTX 950 requires UEFI in the motherboard instead of a standard BIOS.  HP didn't start using UEFI until mid-October 2012.  There is no way to update the motherboard in the UEFI.  Latest video cards do not for UEFI were the GTX 660/670.  I suggest that you choose a manufacturer and contact their Technical Support to help them choose the best card for your system.

  You will also need to upgrade the power supply (PSU).  It is only 300W.  Most newer cards require at least 400W to work properly.  Although status map specifications at least 300 w, members reported that they had at least to 400W.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Strange to sleep with HP Pavilion Elite e9270f problem

  I have a HP Pavilion Elite e9270f running Windows 7.  I have a strange problem sleep/hibernation began about two months ago, which makes me a little nuts.  I usually select sleep in the Windows menu when I want to put the computer in mode 'sleep'.  It takes about a minute of attentive of disk, and then light on this case turns from blue to yellow.  A few months ago, I would either press the yellow button, or press a key on the computer, and I'd hear the fans turns on, light would change from yellow to blue and the computer wakes and be ready to use.

  Now (in the last two months), when I press the yellow button, the fan turns on, the light goes off completely, and nothing is happening right here.

  To recover, press and hold the power button for about 5 seconds, then the computer turns off.  I turn it back on with the power button and then wait so he could get out of sleep of hibernation.  It takes about 4-5 minutes to make it usable.

  Any ideas on what could happen?

  Thank you

  Jonathan

  I tried the steps and processes in the article that you referenced.  Nothing seemed to work.  I had given up and finally thought that maybe the power supply was a problem, since it provided the day before.  To my surprise, a new power supply solved my problems of sleep.  Seems that the original must have had a problem keeping the tension during sleep.

  Thanks for your help.

  Jonathan

• Pavilion Elite e9105z Disc error (BIOHD-8) motherboard is also bad.

  I have an e9105z Pavilion Elite 3 years with windows 7. About 6 months ago, I began to have freezing problems. Finally, I ran diagnostics on this issue and found that the hard drive was bad. (BI0HD-8 error code)  I ran the disk check, and it seemed to fix the defective sector. In a few days after that the whole computer just died. I tested the PSU and it was good. By pressing the button start has no effect. When I plug the thing that happens, is that the green light on the power supply turns on. It is now a paperweight.

  I understand that HP has been using lower Seagate hard drives and motherboards and shipping them knowing that they were wrong and now I'm stuck with a $600 paperweight. I would like some satisfaction of HP but I can't yet talk to them without charge.

  Anyone has had problems similar to mine, and if so have you been able to solve it with HP? I'm little about as upset as anyone can get. I bought several HP products. How to get to someone?  If nothing else, I want to say thank you shipping shit they knew was bad. Any help would be appreciated.

  Please hold me.