Pavilion series P6000 (model #: p6605f) office computer (W7 64 bit)

Similar Questions

• recover hp pavilion dv4-1504tu model: VV020PA #UUF for the 32 bit Windows 7

  Help me to recover hp pavilion dv4-1504tu model: VV020PA #UUF for the 32-bit Windows 7.

  Thank you

  Hello

  The 3 main methods to restore your laptop to "Factory Condition" can be found on the following link.

  http://support.HP.com/us-en/document/c01867418

  Kind regards

  DP - K

• Pavilion series P6000: Configure the new HARD drive.

  I install a new Seagate 1 TB HARD drive in a Pavilion P6620F.  What I need to clone new HARD drive or just run the recovery discs?

  It all depends of what your intentions are.

  You are replacing the original disk or adding storage space?

  The simplest method would be to clone the current to the new hard drive, when you replace the original hard drive. Install the drive cloned in the same place where the Moose an and with the same connectors.  Start the PC and everything should be STATED as it was before, except that it will be on a new hard drive.

  If you add a drive for extra storage of storage, it is simply a matter of conecting a sata conector between unused hard drive and a sata header and connect a power connector from the hard drive.

  Once it is done, turn on the PC and log in to Windows.

  Use Windows Explorer to create up to four partitions and then format the partitions.  I am unware of how space exists in the case ATX mid for additional disks.

• HP PAVILION series P6000: could not get on the internet

  This lasts for 3-4 months. (have been using my laptop to the internet) Everytime I open internet, all I get is a page that says - can not display the page. When running the diagnostics, I get error 651, cannot detect networks, can not detect the proxy settings and a little more. I spent hours. on the phone with Comcast and they their test modem/router and anything else they could think and quite checks very well. In the Device Manager, all drivers are good to go. A Comcast tech thought there could be something in the computer that will be put into market (radio switch). I also tried to replace the ethernet cord, computer is wired. Frustrated, Mjs58

  Hello @mjs58,

  I understand that you are not able to connect to your wired network, and I'd love to help you!

  To re - establish a coherent link between your computer and the network, I recommend later in this document on the Troubleshooting Wired Home networks (Windows 7). This should help to run a diagnostic on your system using the network and Internet troubleshooting, as well as measures to maintain your system on the cable network.

  In addition, I suggest also follows the steps below to ensure that your power management settings do not interfere with your network connection:

  1. open DEVICE MANAGER
  2. open the NETWORK CARDS
  3. right click on the WiFi adapter for the pc and left click on PROPERTIES
  4. click on POWER up.
  5. remove the check mark beside : ALLOW the COMPUTER TO TURN THIS DEVICE SAVE START STOP
  6. click on OK
  7. close DEVICE MANAGER and test.

• HP Pavilion series p6000, mode: will not open a session

  When you try to open a session after having start the computer. He says that the password is not valid. And it is typed correctly, we have tried several times. We tried to restore the computer, but it is not yet let us go beyond the login screen. Help, please

   Hello

  If the message above is the problem, proceed with caution...

  IT OF A REGISTRY TWEAK AND IS ADVANCED IF YOUR NOT COMFORTABLE PLEASE DO NOT TRY...

  Boot into safe mode (tap F8 at startup) once your safe mode desktop computer has loaded click on the start button, type regedit hit search bar enter.  Double left click HKEY_LOCAL_MACHINE next double left click scroll down to MICROSOFT SOFTWARE double left click MICROSOFT scroll down to WINDOWS NT double left click WINDOWS NT, scroll the LIST of PROFILES double click PROFILE, LIST within profile, you will see two files of script long as S-1-5-21-32778... will be a script. BAK at the end of the script. Make a right click the file that does not. BAK at the end and click Rename. Then, at the end of script .BA type highlight the. BAK file, and right click on it and click Rename. Delete the. Then, the part of the file BAK, highlight the click again right the file .BA and rename and add K to the .BA while she reads. BAK.   The long without script. BAK in the end will have to be highlighted again on the right pane, you'll see REF COUNTY double-click REF COUNT and you will see a number in a box to make sure that the number is 0 (ZERO) if not change it to ZERO 0, click OK. Then and then double click on STATE and change again once the number 0 (ZERO)... Reboot and close regedit your machine and you will now be able to boot and load the administrator account once more.   Hope this helps

  You can also follow a tutorial step by step at this link
  

  https://www.YouTube.com/watch?v=vEyxD6ZG-JI

  Checkurtech

  Click the White Star Kudos to say thank you *.
  Please check accept as Solution if it solves your problem *.

• HP Pavilion series p6000: Windows 7 system repair disc

  is it possible to get a repair disc without having windows 7? mine broke and I don't have an ERD. the boot sector crashed on me, so I kinda need a. im using right now it works on xp. not bad, but this computer is slow

  If you have a friend with Windows 7, a repair disc can be done.  There used to be a download for the system repair disc, but it was taken down, so you need a working Windows 7 PC group to make.  A Windows 7 installation disc can also be used - boot the disk and choose repair instead of the installation of the screen after the first screen.

• HP Pavilion series: Message Office says "insertWindows installation disc.

  "Unable to start Windows.  1. Insert the windows installation disc, and then restart 2.  Choose the language setting, click Next. Click on repair.

  I don't have an installation disc.  Where can I get one? I can't do anything on the phone (I know because I can't access the computer to type stuff in)

  The people at Best Buy told to call HP.  Telephone support HP could not help me and directions of site must be of this office.  I think I need to get a drive of fixation.

  Help, please!

  Beth

  You're in luck.  I looked at the model published and found this:

  http://www.computersurgeons.com/p-22368-recovery-kit-a7e40av-for-HP-Pavilion-Desktop-PC-model-number-P7-1170t.aspx

• Computer laptop dv2419us (2000series): is there a graphics card that will be compatible with my HP Pavilion dv2000 laptop (model dv2419us)?

  ? Is there a graphics card that will be compatible to my HP Pavilion dv2000 laptop (model dv2419us)?

  -This laptop has Windows 7 Home Premium.
  -I wanted to take the free update for WIndows 10 - I asked the reservation.
  -First reaction has been waiting for downloads would be available.
  -Just got the message that it is not compatible with Windows 10 because there a GB Nvidia GeForce 6150 graphics card.
  -J' contacted Nvidia on a card that would be comaptible with WIndows 10.
  -Response has been that could not recomment a replacement and contact HP.
  -Does anyone know if there is a replacement of a graphics card for the HP Pavilion laptop dv2000 which would make it compatible with Windows 10?
  ... Or is my only option to not upgrade to Windows 10 or buy a new laptop?

  Hi there @murray62east,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you are curious about a replacement of a graphics card.

  Unfortunately the graphics cards are not replaceable on laptop HP Pavilion dv2000. They are directly attached to the motherboard. The only way to replace a graphics card would be to replace the entire motherboard.

  Hope that I have answered your question.

  Have a great day!

• Pavilion series 17z - F2: how to install memory in laptops series 17z - F2 flag?

  How do we install the memory in laptops 17z - F series (17z-F200, product L2H13AV) Pavilion?

  HP seems to have no guide available for this series of model maintenance. What is happening with this?

  Please, do not offer the generic (and obsolete) Pavilion 17 Notebook PC Maintenance and Service of Guide. It seems not to apply to 17z - F series. This guide indicates to remove the low service panel which I could have understood that mine. However, 17z - F series does not appear to have removable panels at all. I took a shot near the Pavilion 17z-F100. And it is not any removable panels on the underside, with the exception of the battery. So, I guess that 17z-F200 are the same.

  I am a computer technician. And this is the first laptop I've seen without signs of service. I'll probably have to remove the outer shell together to install the memory (or replace the hard drive when the time comes). But, any laptop I've worked on in the past had its own special table hidden screws or special tricks for disassembly. So having an interview guide is a necessity to prevent the pests from plastic, clips, guides, mounts etc..

  What about this one:

  Pavilion manual 17z

  Don't get started me on that. It is one of my hobbies, too. HP is not the only one to do that. Acer and Toshiba, etc. also sell 'closed' systems now. I hate it. I will absolutely never knowingly buy one, but I spend a lot of time here answering questions like this. Good luck and let us know how you do. Looks like you'll be fine.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP P6000 - model: P6624y

  Hello

  My HP Pavilion P6000 - model: 6624y

  I lost my recovery disc.  If someone would direct to download me an if it is available.

  Thank you

  WND

  I seems that HP has defined recovery media.  GO to THIS PAGEand scroll down to "the order recovery media.

  The cost is usually not much $25 - $30

• my laptop keyboard is not working. His pavilion G6 2228TU model please help me.

  my laptop keyboard is not working. His pavilion G6 2228TU model please help me.

  Hello

  This could be a hardware problem, but it is always worth trying the following.

  Open windows control panel, open Device Manager, expand keyboards, "Standard PS/2 Keyboard" right click and select uninstall.

  When you are finished, stop the laptop - if you're running Windows 8 or 8.1, do it by holding down the button SHIFT left click Shutdown to temporarily prevent a hybrid boot.

  Then disconnect the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Kind regards

  DP - K

• How we touch the power LED cable (model SR5702F Office)?

  How we touch the power cable LED on HP 517069-001 (model SR5702F Office)? All but one connector are color coded. Who is that a problem is this is a single line with an end connector have covered the (black). Thank you

  The pinout is a follows:

  

• computer laptop Sony vaio S - series VPCS133GN, operating system windows 7 Professional (64 bit) genune, these days, my pen drives are not installation and opening

  I use a computer laptop sony vaio S - series VPCS133GN operating system windows 7 Professional (64 bit) genune, last few days my pen drives are not installation and opening. Kindly help me.

  Best regards

  A.C. Dutta

  Hi Johanna,.

  Thanks for posting your query in Microsoft Community.

  I understand that you can not use the USB in Windows 7.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this

  1. you get any error message?

  2 have you tried using different USB ports?

  3. any other USB key works on the computer in question?

  4. do the USB works on any other computer?

  5 have had any changes made to the computer before the show?

  Please follow the methods.

  Method 1:

  Run the Microsoft fixit for the link.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2:

  As all devices have same also have USB device associated drivers. Appropriate sometimes drivers not detected after initial installation so reinstalling the drivers can fix the problems.

  You can check after uninstalling and reinstalling USB drivers if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  (a) click Startand then click Control Panel.

  (b) click system and Maintenance, click System, and then click Device Manager.

  (c) Note if the control panel is in Classic view, double-click Systemand then click on Device Manager.

  (d) If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (e) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".
  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (f) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  We would be more than happy to help you if the steps above did not solve the problem.

• blocked password on hp pavilion series g what to do?

  blocked password on hp pavilion series g what to do?

  Hello

  Try the following.

  Using another PC, download the app from the following link and save it in your downloads folder.

  PC login now

  Once the download is complete, open your download folder and double-click on the installer - this will result in another file, which is the disk image (.) ISO) you need to burn to a blank CD.

  Now, you will need to use an application like ImgBurn ( Note: you can deselect additional software offerings when you install ImgBurn) to burn this ISO properly on a blank CD - a guide on the use of ImgBurn to write an ISO on a disc is here.

  When the disk has been created, shut down the PC you can not log on, press the ESC key as soon as you press the power button to access the Start Menu, insert the CD, select Boot Options (usually f9), use the arrow keys to select the CD/DVD drive and press enter - peut also have you to "Press any key" to boot from the CD if asked to.

  Follow the instructions on the guide here to remove the current password.

  Kind regards

  DP - K

• Update for microsoft office 2010 (KB2883019) 32 - Bit edition broke free of charge upgrade to window 7 Home premium in window 10 gives error 80070643

  While the free upgrade my window 7 home premium to window 10, update for microsoft office 2010 (KB2883019) 32 - Bit edition could not give code error 80070643.

  Unable to upgrade Windows 7 to 10 window, error code - C1900101-4000 D - 1update failed.

  Contact microsoft online help-Mr. JACOB - Aff-[delete by MS MODs for privacy] dt 21/09/2015, unresolved problem.

  Hello

  Thanks for posting your question on the Microsoft Forums.

  I understand that the problem with the upgrade of your Windows 7 computer to Windows 10 due to the failed updates for Microsoft Office 2010. I would certainly like to help you with this.

  I would be grateful if you can provide us with the following information to help us better understand the issue.

  1. What is the current status of your computer, you are able to check updates and install?
  2. How do you try to upgrade to Windows 10? Through Windows Update or the media creation tool?

  The most common cause of this error is a problem with the .NET Framework is installed on the computer. You can also encounter this error when installing updates for Microsoft Office. If you were installing Microsoft Office updates when you received the error, follow the instructions in the "Microsoft Office" section below. Otherwise, follow the instructions in the section "Windows.NET Framework".

  To resolve this problem, you may need to restart the Office Source Engine (OSE) service and try again to install the latest updates for Office products.

  Follow the steps in the "to restart the service Office Source Engine (OSE)" section in the link below and check if that helps.

  Windows Update error 80070643

  http://Windows.Microsoft.com/en-us/Windows/Windows-Update-error-80070643#1TC=Windows-7

  If the problem persists, we can try to install the update manually

  You can download and install the update manually from the link below.

  December 9, 2014 update for Office 2010 (KB2883019)

  https://support.Microsoft.com/en-AU/KB/2883019

  After you install the update successfully, check updates and install all pending updates. After a successful of all updates installation proceed with the opening of Windows 10 upgrade once more.

  I hope this helps. Please let us know the results. Do not hesitate to write back for any further assistance with Windows, we will be happy to help you.