Pavilion will not proceed to the start menu

Similar Questions

• Windows XP on my laptop will not stop from the start menu.

  It goes to the screen that says Windows stops, but he never does.

  Hello

   
  1. do you get an error message/code?
  2. don't you make changes to the computer before the show?
  3. which antivirus program is installed on the computer?
   
  This problem can occur if a third-party program or application prevents the computer to shut down.
   
  I suggest for the link and follow the steps in the article:
   
  You cannot log off, restart or shut down your Windows XP-based computer
  http://support.Microsoft.com/kb/831431#top
  -Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
  -ATTENTION: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  In addition, the link and follow the steps in advanced troubleshooting.
   
  Your computer stops responding when you try to shut down in Windows XP
  http://support.Microsoft.com/kb/313290#top
  -Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
  -Note: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
  -Note: Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.
   
  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• CD rom does not appear in the start menu in lenovo G500 windows 8

  Hello
  I want to format my lenovo G500 windows 8 and install windows 7 but I can't because the CD rom does not appear in the start menu

  Hi obaid, welcome to the forums.

  you will need to change some parameters in the BIOS, these changes are explained below related to the thread.

  http://forums.Lenovo.com/T5/Lenovo-3000-and-essential/downgrading-from-Windows-8-to-Windows-7-on-Len...

• After the installation of Windows Virtual PC on my Windows 7 Ultimate 64 bit system it does not appear in the start menu. How can I fix this so that I can run Windows XP in Windows Virtual PC?

  Windows 7 Ultimate 64 bit running on an Intel i7 2600 system with an ASUS P8P67 motherboard.  Intel virtualualization has been enabled in the bios.  Windows XP mode has been installed on the system and the operating system has been updated with Service Pack 1.  Windows Virtual PC has been downloaded and installed, but does not appear in the start menu in the programs list. Now download for Windows Virtual PC will not allow to install another, nor that the first installation can be uninstalled because it is not on the list of programs. Virtual PC folder of Windows in the Program Files x 86 folder has only a folder with two files integration components; IntegrationCompnents.iso and Precompact.iso.

  It should be in the menu... Virtual PC / XP Mode or something. I don't know, I don't use win7 atm

• Recently opened progams are not displayed on the start menu

  Original title: my most recently opened PROGRAMS are not displayed n the Start Menu-Vista ultimate__

  Hello, Im under Vista Ultimate SP2 [32 bit] and what ever updates etc, there is so much current im.  Suddenly the list on the left side of the Start Menu [under the waiting list] shows all the programs that have been recently opened/used. It allows to view, obviously Ive done something along the way but don't can't seem to retrace my steps back far enough. Clicks to memorize and display properties are all not verified so no problem there.  Can someone please help with this annoying problem. May thanks, has soon.

  Type regedit in the start search. Access
  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer
  and delete
  NoStartMenuMFUprogramsList
   
  --
  ..
  --
  "kenhankanen" wrote in message news: c0fac7b4-ec95-4c3b-8345-eb202323410c...
  > Bindu thanks for your reply, but I had tried these steps much earlier on
  > and are the most obvious that can be made. I was expecting something
  > more technical, if necessary, as perhaps a reg key has been changed and can
  > be reset but I am sure that is it might have been, or if in fact it is
  > the cause. I'm sure its base [other Quen exhibited obvious steps]
  [> above], but can't seem to find it in one of the preferences or
  > configuration in the control panel settings. other than furthere ideas
  > create a new user account?
  >
  > Thanks again for your time and help.
  >
   
   

• Hibernate button does not appear on the start menu

  Hibernate button does not appear on the start menu

  Hibernate button does not appear on the start menu

  Here is the link to MS Help and support about the case.

  http://support.Microsoft.com/kb/929658

  Note : scroll down for more information and find out if your computer supports the hibernation.
  Note: If the computer does not support the hibernation feature, you cannot enable the feature.

  t-4-2

• Windows XP Mode does not appear in the start menu after installing it successfully

  Original title: xp mode w7pro

  try to install xp mode/virtual pc on 7pro. down loaded and ran but does not appear in the start menu.  Active virt.tech. in the bios on a thinkpad x201i.

  First Install Virtual PC and following the XPMode.

  http://www.Microsoft.com/Windows/Virtual-PC/Download.aspx

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Windows Fax and Scan does not appear in the start menu

  : I'm using Windows Vista Home Premium and you want to (a) send faxes via a modem local fax and b scan docs from a local scanner. I mean, there should be a program Windows fax and scan shown in the start menu. I clicked all programs on the start menu, and it doesn't always show. Suggestions?

  From: Hal

  Fax and scan is available in Windows Vista Business and Ultimate editions, it is not available in any of the Windows Vista Home editions.  Since you have a version of Windows Vista Edition family, the only option of fax is a third-party product.  These products work under Windows Vista:

  Snappy Fax

  http://www.snappysoftware.com/

  RKSFax

  http://www.rkssoftware.com/rksfax/overview.html

  VentaFax

  http://www.VentaFax.com/

  FaxTalk FaxCenter Pro 7.5

  http://www.FaxTalk.com/products/ftfcp/index.htm

  I have seen reports that the free version of BVRP also works with Windows Vista:

  http://www.usr.com/BVRP/bvrp.asp

  BVRP PhoneTools

  Given the above comes with the new USR modem, I don't know if it will work with no - USR modems.  Alternatively, you can send faxes via your Internet connection provided you are willing to pay for an Internet E - Fax service:

  http://www.slipstick.com/AddIns/services/fax.htm#internetfax

  Personal Fax Services - Internet Fax

  http://www.Savetz.com/fax/

  Another response of the community of Windows Vista discussion groups

• my laptop with 7, the other with vista does not, windows message told to go update that does not exist on the start menu. I'm locked out using my computers

  my laptop, 1 vote against and 7, the other with vista will not work.  I use norton 360.  message at startup said to go to microsoft update on the start menu.  There is no windows update in the start menu.  I'm locked out using my laptop.  Help, please

  For Vista, see http://windows.microsoft.com/en-us/windows-vista/How-can-I-tell-if-my-computer-is-up-to-date and http://windows.microsoft.com/en-us/windows-vista/Updating-your-computer

  For Win7, see http://windows.microsoft.com/en-us/windows7/How-can-I-tell-if-my-computer-is-up-to-date and http://windows.microsoft.com/en-us/windows7/Updating-your-computer

• Satellite A300 will not get before the start screen

  Hi all

  had a problem with a laptop A300 about 2 to 2.5 years old. I just installed windows 7 prof and it worked fine for about 3 days and then all of a sudden it blocked start.

  He gets to the toshiba start screen and then reboots. He doesn't even try to start windows. You can go into the bios and make changes, etc., you can not press f8 to load in safe mode, only it does not even come to that.
  You can press f12 and raise the start menu and try to boot from the CD but this new fact not work and it just restarts again

  I don't know how else to troubleshoot it. I don't think it's a motherboard problem can you enter the bios.
  It could be a HARD drive problem, but then I thought it would have gave you a warning message of any (no available boot device) and you can see the HARD drive in the bios and would have thought that it would have started at least on a CD.

  The only things I can think about are drive problem HARD for the problem RAM or motherboard problem.
  I think install win 7 to 3 days there is just a huge coincidence?

  Any help would be great. Thank you

  Hi hitenkacha,

  Hmm... Which is really strange, if the laptop restarts after the Toshiba start screen but it doesn t happen if you go into the BIOS or boot menu...
  So, if you go into the BIOS and wait a few minutes, he doesn t restart?

  Yet one thing would be interesting to know: what happens if you try to boot from the recovery disk Toshiba? Generally, it should still possible to boot from this drive if it s ok.

  Check this box!

• Helpctr.exe does not load in the Start Menu. System Restore does not work.

  Help and Support not be loading not on the Start Menu. I get a msg of error helpctr.exe is not found. I run for the file with no result. Also the system restore does not work even in safe mode. I use XP Home SP3. Any suggestions? Thank you.

  No problemo!

• recently programs do not appear on the start menu?

  I checked in properties in the start menu, but do not see anything wrong with it and I need to know how to put the 'programs' recently back to the list in the menu start? At the moment it is all areas even after opening certain programs and check again, yet show blanks. The pinned programs above are correct.

  I think it was caused by the update of Advanced SystemCare version, but I don't know, I have tried to use the system restore to go back before I installed this update, he told me that it can not be restored to the point. I have attempted to coupls of days prior to the date of update installed no success at all.

  I enjoyed everyone show me how do

  Hi Dave xp,.

  I would suggest trying the following steps and check if it helps:

  Step 1:

  a. Click Start.

  b. right click on an empty area of the start menu, and then click Properties.

  c. click Customize.

  d. ensure that in programs 'Number of programs on the start menu' is not set to 0 (zero).

  Reference link: Description of the Start Menu in Windows XP

  Step 2:

  Create a new user account and test the question. If the problem does not occur in the new user account and then, you can fix the corrupted user.

  How to create and configure user accounts in Windows XP

  How to copy data from a corrupted to a new profile in Windows XP user profile

  I hope this helps.

• New hard drisk does not appear in the start menu

  Original title: how to install windows vista again portable hard drive

  Hai I bye a hard disk for my computer laptop is 550 HP Seriers notebook, because my previous hard disk have complaints, but when I corrected this hard drive in the laptop the start menu does not display of hardisk why?

  Hello

  1. you have a single hard drive connected to the computer?

  The issue could be related to the physical connection of the hard disk, I would suggest that you check the physical connection of the hard drive and check if that helps. You can also get in touch with the manufacturer for details on the connection.

  The issue could also be tied to the BIOS settings. You can get in touch with the computer manufacturer for help with the BIOS settings.

  Note:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• APPLICATION will not appear on the main menu of the Simulator... Help, please

  Hello everyone,

  I came across this example code and tried to run on the Simulator 9900 and for some reason, the Simulator does not pick up the code. ..

  as the application does not appear on the main menu screen options... so I can not fire at all.

  someone knows why... ID really appriciate the help

  (Note: the simple code opens a new window when clicking on a button)

  Kind regards

  gezzy

  package mypackage;
  
  import net.rim.device.api.ui.Field;
  import net.rim.device.api.ui.FieldChangeListener;
  import net.rim.device.api.ui.UiApplication;
  import net.rim.device.api.ui.component.ButtonField;
  import net.rim.device.api.ui.component.LabelField;
  import net.rim.device.api.ui.container.MainScreen;
  
  public class FirstScreen extends MainScreen implements FieldChangeListener {
      ButtonField theButton;
  
      public FirstScreen() {
          add(new LabelField("First Screen"));
  
          theButton = new ButtonField("New Screen", ButtonField.CONSUME_CLICK);
  
          theButton.setChangeListener(this);
  
          add(theButton);
      }
  
      public void fieldChanged(Field field, int context) {
  
          if (field == theButton) {
          UiApplication.getUiApplication().pushScreen(new SecondScreen());
          }
  
      }
  
      public class SecondScreen extends MainScreen {
  
          public SecondScreen() {
              add(new LabelField("Second Screen"));
          }
      }
  }
  

  I think you are saying that the application icon will not be displayed on the Simulator? If so, this can help (I had the same problem and what I did):

  1 assuming you are using Eclipse, just run the program (it will be forfeit and display an icon to load for a few seconds on the Simulator).

  2. then go to file-> load BlackBerry Application or theme on the Simulator.

  3 navigate to your compiled COD of the file, then open it.

  4 after a loading icon, the application should appear in the menu.

  If this does not work, try to close the Simulator and do step 1.

  I hope this will help!

• Why google chrome will not remain on the start screen

  Well let's go.  When I down load google chrome and place it under windows 8 Start menu and open my email account, it works very well at this point. then when I close my google mail chrome disappears off the coast of my Start menu.   It remains in the Quick Start menu and multiply, here, whenever I chaque fois que j' ouvre open google chrome and open the e-mail.   It just won't stay on the start menu.   Even a bestbuy geekquad tech could not understand it. outside.

  Hi Dale,

  I suggest you to uninstall and reinstall Google Chrome. Then pin Google chrome for the splash screen.

  Follow these steps to uninstall the game.

  a. press the Windows key + X , and then select Control Panel.

  b. Select uninstall a program

  c. Select Google Chrome in the list, and then select Uninstall.

  Now, go back and go through the article to know how to pin to the start screen.

  Has Joust applications, Web sites and more at the beginning

  http://Windows.Microsoft.com/en-us/Windows-8/adding-apps-websites-to-start

  Let us know the results.