'PC' is not set up to establish a connection on port "file and printer sharing (SMB)" with this computer - I get this after enabling access to public folders and then trying to access (another pc on the network cannot connect to this pc but see).

Similar Questions

• Error 0 x 80070035 "[name of the PC] is not configured to establish a connection on Port"File and Printer sharing (SMB)"on this computer".

  Original title: "home network".

  0 x 80070035 "[name of the PC] is not configured to establish a connection on Port"File and Printer sharing (SMB)"on this computer".

  That's what I get on my ThinkPad when I try to do the networking. I placed all the parameters correctly: all 3 of my computers are set the same. 2 workstations work perfectly. They can even see the laptop but not to open all files. The laptop can, open same network t itself file. But he can see the whole of the network (including a printer, is told by the way). I, ve gone through all parameters twice. I've even set the C drives to share via the menus of context on each computer. I have visited many forums with none even come close to this problem (they all will tell you how to set the network parameters or they get very technical and over my head).

  I tried with & without a firewall.

  No password.

  I use a wired network.

  Laptop & 1 desktop computer running vista - 1 desktop computer running xp.

  They have all the latest service packs ms & udates.

  Any help will be appreciated.

  These files can be opened by norton or lenovo network setting apps. The settings do not work only in the application of network of vista. Nor can I work norton or lenovo from other computers.

  PS how can I ensure these settings effect may just lan and do not extend to the internet?

  Thank you bb

  I tried new drivers & returned through sharing & permissions, according to Jack, but he was not good. At the level of experience of my computer I can miss something obvious, but I doubt it because I've been very careful in following the instructions. I am experencing other problems with this laptop as well and I'll just get all. I am planing to get back anyway, that's why I needed network. I wanted to Exchange files over the network to avoid having to ' wait & swap "usb drives. Thanks anyway. Thank you BB bb

• I use a dongle for my internet but suddenly I can't connect. "" When I run windows diagnostics I get this message "not set up to establish a connection on the port.

  Internet connection problem

  I use a dongle for my internet but suddenly I can't connect. When I run windows Diagnostics I get this message... "www.microsoft.com"is not configured to establish a connection on port "service world wide web (HTTP)" with this computer. Can anyone help please?

  Hello

  (1) don't you make changes to the computer until the problem occurred?

  I suggest you to follow the steps below and check if it helps:

  Method 1: Try to start your system in safe mode with network and check if the same problem occurs.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Method 2: If the question does not exist in Mode safe mode then try to put your computer in a clean boot state.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

   

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Follow these steps to reset the computer to start as usual:

  (a) click on start toreduce this top that i, type msconfig.exe in the Start Search box and press ENTER.

  If you are prompted for an administrator password or for confirmation, type your password, or click continue.

  (b) under the general tab, click the Normal startup option, and then click OK.

  (c) when you are prompted to restart the computer, click restart.

  Method 3: Of connection problems in Windows wireless and wired network:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check this link for more information:

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Hope this information is useful.

• Help please (localhost is not set up to establish a connection on port 9443)

  Dear professionals

  I used to connect and connect to the Vcenter server via vsphere web customer, but now I can't connect to it more.

  When I clicked on "diagnose the connection problem" I received this message (please see the attached picture)

  
  

  It's strange because I logged in vcenter server several times, but all of a sudden, I can't anymore.

  
  

  Please me advice what to do

  
  

  Thank you

  
  

  naoufl

  Hey naoufl,

  Check if your vCenter web service and the customer service is running, if it still works try to restart it once. and turn off your windows firewall or check to see if something is blocking the port 9443.

  If still problem let us know.

  Thank you

  Avinash

• When upgrading to Windows XP SP3, Windows 7, it loads the temporary files, and then I got an error message saying "the install.wim file does not exist.

  When the upgrade of xpsp3 for win 7 it loads the temporary files and 1 min in step 2? "" departure ": an error message appears that says install.wim file does not exist?

  original title: problem installing win 7

  Hello

  You can't upgrade Windows XP to Windows 7.

  Windows 7 upgrade paths

  This document describes the upgrade paths that are supported and not supported for editions of the Windows® operating system 7.

  Unsupported upgrade scenarios

  • Upgrade to Windows 7 from the following operating systems is not supported:
  • RTM of Windows 95, Windows 98, Windows Me, Windows XP, Windows Vista®, Windows Vista Starter, Windows 7 M3, Windows 7 beta, RC of Windows 7 or Windows 7 IDS
  • Windows NT® Server 4.0, Windows 2000 Server, Windows Server® 2003, Windows Server 2008 or Windows Server 2008 R2
  • Upgrades on place of several architectures (for example, x 86 to x 64) are not supported.
  • Place of cross-language upgrades (for example, en - us en - us) are not supported.
  • Cross-SKU upgrades (for example, Windows 7 N to Windows 7 K) are not supported.
  • Upgrades from Windows Vista to Windows N, Windows K, Windows KN or Windows E are not supported.
  • Upgrades on place of type Cross-compiling (for example, the fre to chk) are not supported.
  • Pre-release in place upgrades across milestones (for example, Windows 7 RC to Windows 7 RTM) are not supported.

  Supported upgrade scenarios

  Company	Professional, company, full
  Enterprise	Enterprise
  Home Basic	Home Basic, Home Premium, Ultimate
  Home Premium	Home Premium, ultimate edition
  Ultimate	Ultimate

  Enterprise	Enterprise
  Home Basic	Home Basic
  Home Premium	Home Premium
  Professional	Professional
  Starter (x 86 only)	Starter (x 86)
  Ultimate	Ultimate

  Home Basic	Home Premium, professional, ultimate edition
  Home Premium	Professional, ultimate edition
  Professional	Ultimate
  Starter	Home Premium, professional, ultimate edition

• Local host is not set up to establish a connection on port nnnn

  I installed VS 2010 Ultimate and Silverlight 4.0 and they seem to run OK on this Vista platform.  I also use Security Essentials.

  However when I run a sample application (using asp) which apparently works OK for Microsoft guru (Karl Shifflett) who wrote it, IE 8 throws the error in the title above.

  While they inspected on the internet, I found a lot of similar problems that generally seems to point to a security problem.  However, I can't find the problem.

  Please help, thanks

  Bob R

  Here is the Vista Forums.

  http://msdn.Microsoft.com/en-us/vstudio/default.aspx

  Try the repost in entrusted VS communities.

  http://social.msdn.Microsoft.com/forums/en-us/category/VisualStudio, vsarch, vsdbg, vstest, vstfs, vsdata, vsappdev, visualbasic, visualcsharp, end

  Visual Studio forums at the link above.

  See you soon.

  Mick Murphy - Microsoft partner

• Getting the error "There is an IP address conflict with another system on the network." on XP computer

  "There is an IP address conflict with another system on the network." I keep getting these messages on my computer. -What it means and how to solve this?

  IP addresses are assigned to a computer in one of two basic methods: the address is assigned automatically by the device "in charge" of the network (in your case, the wifi hotspot router) or the address is set manually on the computer.

  If the address is assigned automatically, the router is "smart" enough to assign a different address for everyone.  However, if your computer has a fixed or 'static' IP address assigned manually, it may conflict with an address assigned by the router to another computer.

  You do not specify, so I'm going to assume that your computer is running WIndows XP...

  1. On your computer, open the network connections (start > run > ncpa.cpl > OK)
  2. Right-click on the icon for your wireless adapter and select Properties
  3. Click on the 'Général' tab, select "Protocol Internet (TCP/IP)" from the list of "this connection uses the following items" and click "Properties".
  4. Select the boxes for two on "Obtain an IP address automatically" and "Obtain DNS server address automatically"
  5. OK your way out.

  This will not adversely affect your computer somehow.

  If the two "automatic" settings were already selected, it is likely that your wireless adapter is managed by a utility provided by the manufacturer of your computer or your adapter wifi rather than Windows.  There should be a wifi icon in the system notification area (near the time display).  Click or right-click on it and see if you can access the menu of configuration settings or to determine at which it is useful.

• Windows XP SP3: There is an IP address conflict with another system on the network.

  As mentioned, I am under Windows XP SP3.  Starting around June 14, 2011, I get this error message: "There is an IP address conflict with another system on the network."  I didn't any problem access the internet, which is weird considering all the forums I've read the user has had problems with this.

  I followed the steps to solving this problem.  I checked the IP addresses on all devices connected to my network. none match the computer, I get this message.  I tried refreshing and renew my address this computer's IP, but that has not solved the problem.  I've updated my modem drivers; who has not solved.  I checked the settings on my router but nothing.  I have turned off all devices in the House connected to the network, unplugged both the modem and the router, plugged the modem back in (anticipated for a constant signal), then plugged the router and gives him the time, but I got the message again.  I ran scans anti-virus and anti-malware, but neither picked up something.

  I am out of resources in this regard.  I guess that something might be wrong with the router, but that doesn't seem right.  I had no problems with the router as I bought it a year ago, and as I mentioned there are no connectivity issues (always as fast as I'm willing to pay my provider).  Two things have popped up in my mind that could possibly impact this: all about 14, there was a Windows update that has pushed down and the message began not to burst, until, after downloading (but I have not had this same problem on other computers that have received these updates) , and there was a very, very brief power surge (second meaning) in the House around the 16th which caused no (to my knowledge) do anything stop but not a hand a few clocks.  Thank for any help with this!

  No. except if you must move the computer to another network or if you are not actually that responsible for the network.

  As long as you are in charge of your network, you can configure your router to reserve an IP for your machine OR set up so that the DHCP range is, for example, all the IP addresses above to x.x.x.100 and you you give an IP address below that (say x.x.x.99).

  In the first case, you let your computer configured as DHCP - your router just recognize it and gives this machine (and only this machine) reserved IP address.  For the latter, need to change the settings in Windows after changing your router so the DHCP range does not interfere with the static IP address range.  I would say that the latter is more likely to be a problem than the first, especially if there is a chance that this machine moves from one network to the other.

  Personally, I use the booking method on my home network.  In this way my laptop, iPad, etc. all get a given IP address every time (an I know) and I have to set up the real device special somehow.

• That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  A

  Most likely, the computer becomes a network address of a router. The assignment of an address ("lease") expires and must be renewed after a certain period of time, which could be an hour or a day. The lease expired without being renewed because the device has been disconnected at the time. Meanwhile, the address has been leased to another device on the network, or maybe the router has not updated its list of addresses the leases. When the device offline comes back online, a conflict results. Depending on the type of router you have, the conflict can resolve itself automatically. If not, then in the menu bar, select please

  ▹ System Preferences network ▹ 

  If the preferences window is locked, click the lock icon in the lower left corner and enter your password to unlock it. Click the Advanced button, and then select the TCP/IP tab in the sheet that drops down. Look at the menu option

  Configure IPv4

  If the selection in this menu is

  Using DHCP

  Click on the button

  Renew the DHCP lease

  Test.

  Make sure that you have more than one DHCP server on the network. That could happen if you have more than one access point Wi - Fi, or if you have a router and broadband a wide device distinct in connection mode sharing.

  B

  Less likely, you have a network address that you assigned yourself and another device is itself by assigning the same address. In this case, the selection to configure IPv4 menu will be either manually or using DHCP with manual address. This kind of conflict will not be resolved automatically. You have the following options to solve:

  1. Change the selection in menu using DHCP.
  2. Change the address assigned manually to one that is not used by another device.
  3. Change the address of the other device.

  Which of these options you choose depends on the details of why you use a static IP address. Any changes you make to the network settings is necessary before taking effect. To do this, click OK, and then click apply.

  If the router is also your device at wide band, then he may be operating in bridged mode. In this case, only one customer at a time will be able to connect to the Internet. Consult the manufacturer or ISP documentation for how to reconfigure the device in the connection mode sharing.

  C

  According to a report a "DirectTV" receiver can cause the problem. If necessary, disconnect the device from the network, or power off and test. Consult the support services provider.

• IP address conflict with another system on the network.

  Our operating system is Microsoft Windows XP Professional Version 2002.  WE have set up on a small network of 6 computers.  On three computers, we get a window that opens by telling us that "the system has detected an IP address conflict with another system on the network."     Any ideas as to how we might resolve this problem?

  Hello Jackie,.

  Also, try the following.

  Method 1: Check the settings for dynamic host, Host Configuration Protocol (DHCP) on the router. Contact the manufacturer of the router or the access to the same provider.

  Method 2: Release and renew the IP configuration.

  • Click Start. Click Run, type cmd, press ENTER.
  • Type the first command enough ipconfig and press ENTER.
  • Then type the second command ipconfig / renew and press ENTER.

  See if help above.

• Users on the network cannot use the files after upgrade to Windows 10

  When I switch to win 10 people on the network cannot use the files on my computer

  Hello

  Thanks for posting your query on the Microsoft Community.

  With the description, I understand that you have problems with network connectivity and access files on network on your Windows 7 machine. I will certainly help you to the query.

  I would be grateful if you could help me with more information to better understand the problem and a solution:

  1 is this computer connected to a network domain or home?

  2. what exactly happens when users on the network try to use/access files on this computer? Do they get an error message/code?

  In the meantime, I suggest you refer to the below mentioned thread and check if this is useful:

  http://answers.Microsoft.com/en-us/Insider/Forum/insider_wintp-insider_web/Windows-10-network-file-sharing/18fba63e-7b6c-46FE-BA23-575a634fcee8

  Hope this information is useful. Please write us back with the required information for assistance, we will be happy to help you.

• NAS hard drive not accessible more: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  Dear,

  I am desperately looking for a solution for my specific problem how access my NAS.

  I have a hard drive from Western Digital NAS (Book Live) which worked fine until now. Yet, I just changed my internet provider and I now have a new Fritzbox 6360. Now, I can not access the hard disk of the commune of programs in Windows. I contacted two suppliers already, but without success. I think I have some incorrect settings in my Windows 7, 64 bit. This is the situation:

  -NAS is still working with my old Fritzbox, for testing that I went back-> ok

  -I can access the NAS via the dashboard or a TwonkyServer-> ok

  -When I access it via Windows Explorer, I wonder is to give my credentials (which don't work) or I get the error message: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  -J' changed my IP address (dynamic even static) and connections, password-> without success.

  -J' tried SFC with the result that found no violation of integrity. -> ok.

  Any idea?

  Can you please turn off the NAS, unplug the cable and Ethernet cable? Wait about 2 minutes then plug all the cables back in. Any security program or firewall to this computer? Try disabling it for now.

  You have another PC or laptop which has Windows 7/8 and try to access the NAS?

  You have a smartphone or a Tablet and download an application for the WD NAS and then try to access files.

• "Another device on the network use my ip address".

  I tried to check my mail and could not and got this message "another device on the network use the IP address of your computer." I have never seen it before. He also said that I could change the IP address, if I continued to have problems. I bought this iMac and used Migration to transfer all the stuff from my old iMac that is still used. That was months ago, but I never had this message up to now. So should I change one of the IP addresses? And if so, how is that done?

  http://osxdaily.com/2010/09/19/another-device-on-the-network-is-using-your-Compu ters-ip-address.

• After uninstalling the grid Infrastructure: virtual host name [INS-40912] assigned to another system on the network

  Hello

  I deleted successfully installed grid Infrastructure software. Now, I installed again it but the installer complains about '[INS-40912] virtual host name assigned to another system on the network", which he complains not in the first installation process. :/

  EDIT: I checked and both nodes of the cluster are interpingable through their virtual IP address.

  I see that the previous installation has created a clean interface for this virtual IP address:

  eth0:2	Link encap HWaddr 00:50:56:B9:0E:AA
  	INET addr:10.200.11.159 Bcast:10.200.11.255 mask: 255.255.252.0
  	RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
  	Basis of interruption: 19 address: 0x2000

  OK solved: I just do:

  ifconfig eth0:2 down

• How to access multiple VMs on the network with nic 1 host?

  Greetings,

  I have a server vmware running windows XP with 3 virtual machines in suse. I would like to access the 3 virtual machines from the network at the same time. The vm 3 has their own static ip address. I use the bridge network mode. There is only 1 NETWORK card on the XP computer. With this configuration, I can access only 1 vm the network at a time. When I added an another NIC and jumpered it on a second computer, virtual, then I can access 2 at the same time.  Any ideas on how I can access all the vm 3 at the same time on the network with just 1 NETWORK card?

  Even if you only have a physical NETWORK adapter, you should be able to access all the guests at the same time when they use bridged networking and have a correct IP configuration. Can you put your host IP configuration and your guests so we can check it out. Make sure the guests are really "bridged" and disable all firewall during the test.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!