PC won't start after setting the default settings in the bios of the a10

Similar Questions

• Windows vista completely crushed hard drive won't start after installing the packs of services and internet explorer 9

  Thought I did my brother a favor so that he was at work and installed service Pack 1 & 2 on its 32-bit vista operating system, and then installed internet explorer 9 and it crashed the entire operating system nothing work, hard drive, monitor, mouse nothing. I hope this isn't a hardware problem which needs the advice of experts, the guilty feeling like I had left him only someone help with this can not start even to the bone g .thanks

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  and if all else fails and you need to reinstall vista are the normal methods for computers preinstalled vista portable

  Contact the computer manufacturer and ask them to send vista recovery discs

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

• "Pavilion dv6000 won't start after inserting the password

  I have a dv6000 Pavilion laptop with Windows 7 Operting System.  After a few recent updates at the beginning of my use of the computer (instead of at the end of my computer use), when I turn on the laptop, it brings up my user name and a password field, which, once I insert the password, it should redirect me to the window of the Application.  But after having inserted the password, the word "Welcome" with a circle of rotation appears on the display screen. This ' circle' rotates to progress to subject one minute and then display will Dim and never produced the home screen of the Application.  I greeted the dark screen to stay on the computer for more than 5 minutes and the House request never appears.  The only way to shut down Windows is to press Ctrl-Alt-Del, which produces a window with the following options: 1) lock this computer 2). Change user 3.)  Close the session 4) Change a password 5). Start the Manager of tasks with a button CANCEL in the center of the display and of the farm to the bottom of the icon in the lower right with the following options: 1) 2 restart.) (Sleep 3). Hibernate 4). Stop.   I used the option of doen stop to turn off the laptop.  What can I do to solve my problem and use the computer that I use for?

  Hello

  You are welcome

  I suggest you download AdwCleaner this link to delete the associated files - Save in your downloads folder.

  https://toolslib.NET/downloads/finish/1/

  A once downloaded, close all programs, open your download folder and double-click the application to run it (click Yes to any uac prompt).

  Click the scan button.

  When the results are displayed, click the Clean button - when you are prompted to restart, click Ok.

  Best regards

  DP - K

• Windows 7 won't start after secuity 12/10/2010 dates

  original title: updates security for 10/12/2010

  Windows 7 won't start after secuity 12/10/2010 dates

  Hello
   
  Follow these steps and check if that helps.
   
  Step 1:
   
  Remove all external devices and then try to start again.
   
  Step 2:
   
  Start your computer in safe mode and check if it starts.
   
  Step 3:
   
  If it starts in safe mode, and then try the system restore , safe mode.
   
  Let us know.
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• After setting the brightness of the screen to the medium level, it change to the lower level after a few minutes.

  Original title: adjustment of the brightness of the display

  I have Lenovo laptop with Windows Home Premium. After setting the brightness of the screen to the medium level, it change to the lower level after a few minutes. Why can't I corrected the brightness of the display to the level I want?

  Hello

  I understand that you are facing problems with the brightness of the display. I understand the inconvenience.

  1. did you of recent changes to the computer before the show?

  2. What is the number of the model of the computer?

  Let us perform the following methods and check if it helps to solve the problem.

  Method 1: Try the Aero Troubleshooter

  Click Start, type Visual and then click on 'Find and Fix problems with transparency and other Visual effects.

  Follow this troubleshooter to see if that fixes the problem.

  Method 2: Uninstall and reinstall video graphics driver

  Update drivers:

  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

  Method 3: Adjust the brightness and contrast of your monitor

  http://Windows.Microsoft.com/en-us/Windows7/adjust-your-monitors-brightness-and-contrast

  Reference:--

  Calibrate your screen

  http://Windows.Microsoft.com/en-us/Windows7/calibrate-your-display

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

  Kind regards!

• iPhone 4S.  Stuck on request to post a link to iTunes.  Has started after installing the recent software update.  Tried to turn but the iTunes link keeps coming.

  iPhone 4S.

  Stuck on request to post a link to iTunes.

  Has started after installing the recent software update.

  Tried to turn but the iTunes link keeps coming.

  You can not connect the phone to iTunes as requested?

• 2011 21 inch iMac won't start after the SSD upgrade

  Recently, I upgraded my hard drive for an SSD via a computer repair business in my neighborhood, I also upgraded the ram, but I don't think it's in the case. On a two weeks after the upgrade, my computer don't turn on more. I took it to the genius bar and they told me that the DSS had "failed." So of course, I took my computer to the computer repair company and they ran some tests, discovered that the hard disk does not (according to them, he only read this way because the apple store has run the test for a normal hard drive and not an SSD). I'm not super computer savvy, so I took their word for it.

  Now, however, it has been nearly a month and my computer refuses to activate once again. Previously, it has worked well, the fans were running at full blast - what I knew would be a problem (although the repairman told me that they 'fixed' this issue too). So the first time, I downloaded a program called SSD fan control and set the fans to run in silent mode. This second time around, I realized that it was probably a bad idea because it could lead to overheating, so I put manually the fan speed so that we could hear still run, but just not as loud.

  I tried the reset SMC, but no result. Right now, I unplugged everything including disconnect it from the power strip.

  Any other experience of power with a new SSD failure? Is there anything else I could try at home before contacting the computer again repair business? I would not be able to reach at least until tomorrow, and I'm really curious to know how they managed to get my computer back on the first time.

  Also, I've been out of my warranty period for about a year, so that's why I thought that I was not risking too much by exchanging the original for one SSD drive.

  First of all, the original in Middle 2011 iMac hard drive had a temperature sensor integrated in the drive.  More new or replacement of those who do not.

  Other World Computing sells an Apple certified temperature sensor that plugs into the SATA cable.

  https://eShop.MacSales.com/item/OWC/DIDIMACHDD11/

  I just put a 2 GB Western Digital Black in mine, with the sensor.

  I suggest all first, reinstall the OEM disc and see if it boots.

  Put the SSD in an external enclosure and see if it runs...

• Compaq Presario S4500UK won't start after disconnecting from the wall outlet. What is a CMOS battery problem?

  Reconstruction of recent software with HARD drive internal extra (March 2011) under Windows XP/Linux dual-boot installation worked fine.  CD/DVD RW drive, started giving errors so replaced cyclic redundancy check drive a week ago.  All still OK.  Change of electricity supplied and increases energy use conciousness off the machine to the outlet of the overnight after normal shut down.  Machine will not re-start not in the morning.  Not load BIOS; all lights came briefly and then die after 3-4 seconds with power still led on.  You can get a similar effect by plugging the keyboard into the PS2 Mouse Jack I did once!

  After 20 minutes or so try all kinds of things managed to boot from the CD of Linux.  Shut down/restarted and everything is fine so I don't switch off at the wall.  Also seems to be OK after brief power off for 5-10 seconds but the problem persists with any long disconnection.  It seems that after 10 to 15 minutes from power-on and 2-3 attempts to restart, BIOS comes up and all is well, but he stopped in the middle of a start of Windows or Linux on a couple of occasions.

  Am I right in thinking the problem might be the result of a dead CMOS battery?  The reason that I ask is that the clock seems to keep time OK and there is no apparent problem with the BIOS once it loads.

  Any help/advice would be much appreciated.  New config info below.

  Dual boot Windows XP Pro SP3 of Compaq Presario Bios v3.03 S4500UK / Linux Ubuntu 10.04 Lucid (2.6.32 - 33)

  Drive HARD 120 GB (original Seagate Barracuda 7200) Master Boot Record, Partition Table, Windows XP, Linux, Swapfile etc.

  500 GB Western Digital Caviar Blue (encrypted)

  CD/DVD-ROM (original JLMS XJ-HD166S)

  Recently installed HL-DT-ST DVD - RAM GH22NP21 replacement NEC ND - 1100

  +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

  I don't have all the answers so I went forward with replacing the CMOS battery, but that did not help.  The problem is also obvious if I turn it off and leave it for an hour or more before trying to restart even if I do not unplug the wall plug.  It seems to take about 15-20 will start again before it fires.  I would be really grateful for any clues as to what is wrong.

  TKS

  JG1

  OK, guys.  I finally solved the problem.

  After you have calculated the power needed for the config curent, I discovered that, using various ways to estimate, he walked between 321W - 383W.  It was pretty weird that the only thing I added was a HARD drive and a memory stick and the wisdom of the other guys on this forum, it's that there is a lot of capacity within the factory installed power of 250W.  Yes and here's the rub: the modern replacement devices usually have upgraded capabilities and use more power.  And so when I replaced the drive CD/DVD RW added a few watts, as the sectoral approach of the floppy drive.  It appears also that the optical USB mouse needs more juice than the good old PS2.

  I just installed a new 450W PSU Powercool and Bingo!  The processor is faster, too.

  Hope that my pain and trauma saves someone else having to suffer the same.

  JG1

• Equium L40 - Vista won't start after installation of product recovery

  Hello

  I had to realize a product uses recovery provided restore disk on an Equium L40 computer laptop (PLS41). The recovery procedure done his job to the end, reformats and copy all the files and then restarts. Now the problem starts...
  The pc gets in front of the BIOS boot screen, then it goes completely black with only a cursor to underscore flashing in the upper corner of the screen. No HARD or CD-rom drive activity.

  I did the cover about ten times now. All with the same result. I tried the repair procedure using a Vista boot CD and I also tried using another disk supplied with the computer, anytime upgrade from Vista. Here they are without defects, see the hard drive and shows that the vista files are on it, also sees the winRE partition.

  I tired even fresh install from the disc at any time. It also reformats the disk, copies and decompresses all files needed, begins to install the updates on the disk and then said: he needs to restart. It restarts and goes to black screen with flashing underscore cursor. What happens if I press the 'coup of any key to boot from CD' or leave it to boot from the HARD drive.

  I tried to fix this for two days now, including endless hours of forum to research, the computer belongs to my friend gets very angry I am. I need help. No one knows how to fix?

  Hello

  According to your message, I think that the HARD drive is faulty.
  I think there's a defective recording of MBR (MBR) of the drive and therefore the laptop refuses to boot.

  One question; have you tried to set the BIOS default settings? If this is not the case, try this.

  If it doesn t help and the laptop still does not start upward, then you should ask ASP for verification.
  I think it s a problem of HARD disk and, possibly, the HARD drive must be replaced!

  Greetings

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• Black screen, high regular of underscore on the left does not start after reflashing the BIOS F.38 on HP2000-363NR

  HP2000 363NR, recently tried flashing the BIOS F.38 (here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116227-1&cc=us&dlc=&lc=en&o... ) to solve a problem of overheating.

  Well, it was a mistake.

  Now it does not start at all.

  Fans spinning upwards. Hard disk rotates.

  By pressing ESC, F1, F2, F9, F10 and F11 at startup to give appropriate (fast!) messages but then go to the same place:

  Black screen with flashing underscore in the top left. Leave it to this screen has no effect.

  Never see no text except the quick messages in the lower left (or "Press the ESC key for the system menu" down left based on nothing).

  Out and the relocation of memory does not work. Boot with a DIMM module does not work. Now hold power for one minute while the battery and plug on does not work.

  Battery is fully charged.

  OS is Windows 7 64 bit Home Premium, came with the laptop.

  Is it possible to return this BIOS?

  -Me

  Thanks to Xraytim in the post below, short-circuit the battery CMOS me returned to the previous BIOS. Need to remove card system as a whole to achieve this * beep * connector, but 34 screws later (34 = some # between 15 and 50), BIOS is back, problem solved.

  Thanks for the forum!

  -Tim

  http://h30434.www3.HP.com/T5/notebook-lockups-freezes-hangs/DV9858ca-won-t-boot-after-BIOS-update-won-t-power-with-AC/TD-p/555547

• HP Photo smart 7520: how to switch color after setting the black HP7520 only

  How to switch color after setting printer black HP7520 only

  Hi junosa,

  I'm glad to hear that you finally found the color prints you need.

  When you change the printer setting with the method, you suggested that he change the parameters by default for the printer all of a work are printed with these settings unless you make changes just before printing. If you what to adjust the setting before each print job uses the method that I provided in my first post answer. That's all what you find easiest.

  With regard to the button apply grayed, apply the button becomes clickable when there was only a modified setting that needs to be saved.

  Please click the "accept as Solution" and the "thumbs up" button up on top of my first response above and other similar issues may find the easiest solution.

• Problem, radio won't start after update to Mozilla Firefox 12

  I have problem with a radio to a Web site after the update of Mozilla Firefox 12 when I connect to the webste radio starts, when I use Internet explore the radio starts. Check the image

  http://img859.imageshack.us/img859/3150/egweggwe.PNG

  Your list of plugins shows two WMP plugins.
  
  The classic WMP plugin (Npdsplay dll) and the new WMP plugin (np - mswmp.dll).

  Try disabling the WMP classic (Npdsplay dll) plugin in tools > Modules > Plugins

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Laptop computer DV6174ea not start after upgrading the bios!

  HP dv6174ea lapop - Win XP media center edition with sp3 - processor intel core duo - 2 GB ram - 120 GB hd

  Ive just used the upgrade of bios of HP downloads flash to upgrade the Phoenix bios on my dv6174ea to version 2.9 1.06.Flashed successfully but on reboot it reaches windows XP start screen (black with logo) fails then a blue screen and restarts quickly. Same cycle occurs again and again. Ive tried to boot from the XP cd, but it gives the message "no hard drive not detected" and fails. detect the drives in the BIOS there is no options to the automobile.

  Curiously, a USB bbot containing paragon hard disk manager won't start and sees my drive (two partitions) and the system partition is active.

  I wonder if the flashing the BIOS changed settings or drive letters so that windows does not see properly. I wish there was just a simple option in the bios for detection of discs.

  Can someone pls help.

  If you want to start your computer from the xp cd, then enter the bios and it try to disable the sata mode and activate the ide mode and then try to format your drive... it should work... !!!