PCI-6025E (DAQ) and cards-1409 (Image Interface) PCI

Similar Questions

• Difference between DAQ and DAQmx for acquisition of data PCI 6534

  Hello

  I use the PCI DAQ 6534 card for my digital I/o transfer. I am beginner in the labview.

  I want to store the data coming in memory and the reading of the data at the level of the trigger.

  I have seen the examples in the labview. Some have used DAQmx and DAQmx read write that screws and some have used the confg DIO port and all...

  So I want to know the difference between these two. For my application that I use?

  Hey Bo,

  First of all, I would recommend that you discover the NI 6533/6534 for NOR-DAQmx help. You may be able to find some of your answers in this help document. Now for what you try to do in your application, it looks like you are only buying data. If this is the case, with the 6534, the device acquires data in memory shipped as soon as the DAQmx series start task VI, as long as you don't start hardware triggers have in place. If you have a trigger of starting material, then will make the purchase of the aircraft after the DAQmx start task VI and only after you receive this material trigger. If you call not the DAQmx Read VI, then the data will be stored in the memory board for you, as the driver manages this data in the on-board memory storage, until reading DAQmx VI is called, which at that time, data is transferred to the Board of Directors in the memory of the computer. Once you get it in the computer's memory, you can do whatever you want with these data, as this graph or treat. If you look at the sample programs (which have been mentioned on how to find those in a previous post), you can find an example that little shows you how it works. One of the examples that you can check is called reading Dig Port-Ext Clk.VI. In this example, it sets up to read a finite number of samples and then starts the task. If you set a breakpoint on the line of the error after the VI begin, the data will be acquired in the amount of on-board memory. Then when you cancel the break of the VI, data will be extracted from the amount memory embedded in the memory system with the reading VI DAQmx. Again, the pilot takes care to put the data in the memory board for you once you start the task.

  I hope this helps. Please let us know if you have any questions or concerns about this issue. Also, certainly, discover and try to run all the programs related to the 6534 examples so that you can learn how the equipment works and how to use features to do what you want your program to do. Also, be sure to read through the help on the 6534, as well as the help of VI documentation to learn what makes each function. Thank you and have a nice day.

  Kind regards

  DJ L.

• I just installed menu 24 Firefox and Gmail (Search Images cards Play...) have disappeared. How to restore this menu?

  I just installed menu 24 Firefox and Gmail (Search Images cards Play...) have disappeared. How to restore this menu?

  If it's the black navigation at the top that you bar look, we're sorry, that it has nothing to do with firefox.

  For your information

  The bar is removed by Google, Google updated their menu bars, as last week check out this article for more information http://techcrunch.com/2013/09/19/googles-new-app-launcher-style-navigational-menu-weeks-away-from-launch/

• HOW smart card smart card slots look like? What are the differences between smart card slots and cards express?

  HOW smart card smart card slots look like? What are the differences between smart card slots and cards express?

  Hi Smitty,

  Yes, so ExpressCard is an interface that has a USB port to this topic where I can plug in external devices to be attached to my computer right? I did a search on google but could not find photo Card Slot smart. I need a picture to get an idea of how look like a smart card Slot.

  Next time try BING...

  http://tinyurl.com/95rgwxw
  http://tinyurl.com/9plc7zt

  http://tinyurl.com/8h96qsr

  Scroll to the left view (image 5)

  http://support.Dell.com/support/eDOCS/systems/latd610/en/ug_en/about.htm

• How do we keep Photos when I insert a memory card containing images?

  How can I prevent the Photos when I insert a memory card containing images?

  Mac Pro and OS 10.11.4

  In Preferences > General > import: I unchecked that box, but I can't stop Photos when I insert a memory card.

  Since most of the people would this need, I'm sure I'm missing something obvious.

  After pictures launches uncheck the box to open the Photos whe this devices is connected - it is right of the map in the sidebar of Photos

  LN

• Copy and paste an image vs fill in an email or MMS

  Curious to know if anyone has a preview here. I'm doing an app that will include images to send by email or text (MMS).

  -Road 1 - place them in the Clipboard and let the user pasted everywhere where

  To bring them to the Clipboard, it seems that I use Clipboard utility functions and get the image in a QByteArray. It seems not too difficult, but I don't know how I'll test it on the Simulator. It doesn't seem to be all the built-in apps that allows you to paste in an image (such as the MMS on the iPhone or in an email in Mail).

  Any ideas on how to test the collage of image data? I guess I could build an application that the receiver of the dough, if there was a standard user interface control that could receive the pasted image.

  -Route 2 - use the API to create a message in my application

  I see an example for email, but this seems too complex.

  Is it possible to simply call the stock by e-mail or messaging app and pass it a file to use as an attachment to the message?

  Thanks for the help.

  Kurt

  Impossible to copy paste.

  Ivokation framework to use the 'maps' is pretty easy to use. Don't go the route of the Messaging API.

• Dynamic crypto several cards on the interface

  I have an ASA 5540 executes code 8.2. The firewall has tunnels, VPNS, IPSec standard on this remote access VPN and SSL VPN without client.

  I have 1921 Cisco routers with 4 G wireless cards must open dynamic VPN with the ASA 5540, so it seems that I need to implement a solution of EzVPN here.

  My question is, multiple dynamic crypto maps are supported on a single interface?

  For example, the current configuration of lists

  PFS set 20 crypto dynamic-map outside_dyn_map Group 1

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  In addition to cryptographic cards for static L2L tunnels.

  I guess when I add the EzVPN I have to create a new dynamic map. After having done that, simply add something like that?

  card crypto outside_map 65534 ipsec isakmp dynamic outside_new_map

  Basically a different sequence number and card name?

  Hi Colin,

  It is fundamentally correct, that you will encounter some problems on incoming connections, two on the external interface dynamic crypto map entries.

  One possibility would be to include a return address for correspondence for you EZ - VPN, for example, generously describe the Remote LAN as the destination of the encryption access list.

  For example if your remote LAN is all within the range 10.66.0.0/16 set up an access as list:

  outside_new [local area network] ip access list allow [local mask] 10.66.0.0 255.255.0.0

  and include it in you card crypto dynamic outside_new_map

  PFS set 20 crypto dynamic-map outside_new_map Group 1

  Crypto-map dynamic outside_new_map 20 the value transform-set ESP-3DES-SHA

  crypto dynamic-map outside_new_map 20 the value corresponds to the address outside_new

  See also:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/IKE.html#wp1042880

• Card crypto on Interface Ethernet

  Hi all

  I don't have that much experience but with VPN configs, so maybe this question will seem a bit silly. I have a Cisco 831 that I use to connect via VPN to a remote site. Everything works fine.

  Then I wanted to add a second tunnel to another location. I did all the configs needed, applied card encryption on ethernet external and everything was fine, I could connect. But then I noticed that the new encryption card has actually replaced the existing one. Of course, the first VPN was no longer works.

  Is this a limitation of the 831? Or y at - it another way to configure them so I can use the two (or even more than two) at the same time? Do I need another Cisco router if I want more than a tunnel?

  Any help is appreciated.

  Thank you

  Stefan

  This isn't a limitation of the router. But by design,.

  only one crypto map set can be assigned to an interface. If multiple crypto map entries have the same name but a different seq - num map, they are considered as part of the same set, and all apply to the interface.

  So what you need to do is create crypto-map with the same name for slot 2, but give a different sequence number. Apply this encryption card to the interface and it will work. From the seq - num lowest crypto card is considered to be the highest priority, and will be evaluated first.

• doubt Doc ID 1618305.1 how to install and configure the user interface for content with WebCenter content 11.1.1.8.0

  doubt Doc-ID 1618305.1 How to install and configure the user interface with WebCenter content 11.1.1.8.0 content

  The portal_domain field contains;

  AdminServer (admin) and Enterprise Manager, (port 7001)

  IBR_server1, (port 16250)

  UCM_server1, (port 16200)

  WC_Spaces1, (port 8888).

  On the same machine, I have another weblogic, admin and for the ITS.

  The case is that continued to develop for the upgrade to the new skin WebCenter content.

  That's my goal.

  Then I did some research and came to the following notes in support.

  1 - how to install and configure the UI content with WebCenter content 11.1.1.8.0 and 11.1.1.9.0 (Doc ID 1618305.1()

  https://support.Oracle.com/epmos/faces/DocContentDisplay?_afrLoop=290841671406625 & ID = 1618305.1 & _afrWindowMode = 0 & _adf. CTRL-State = c7eq7vwdt_216

  and

  2 - update of the 11.1.1.8.0 UI content after you apply the Patch of Bundle WebCenter content 3 (MLR 3) or higher (Doc ID 1617477.1()

  https://support.Oracle.com/epmos/faces/DocContentDisplay?_afrLoop=291485823387355 & ID = 1617477.1 & _afrWindowMode = 0 & _adf. CTRL-State = c7eq7vwdt_245

  The UCM_server1 has the following House / app / oracle / Middleware / Oracle_ECM1 /.

  And the list of patches;

  ===================================================================================================

  Installed products of higher level (1):

  Oracle WebCenter content management install 11.1.1.8.0

  There are 1 products in this House of Oracle.

  Installed products (40):

  Cloning of the 11g Application Server 11.1.1.8.0 component

  Enterprise Manager Application Server Integrator Plugin - Management Service Support11.1.1.7.0

  FMW Control Plugin for Oracle inbound refinery 11.1.1.8.0

  FMW Control Plugin for Oracle WebCenter Capture 11.1.1.8.0

  Component install SDK 11.1.0.9.0

  Oracle Application Server Configuration 11.1.1.7.0

  Part of Oracle 11.1.1.7.0 Bali

  Oracle 11.1.1.8.0 capture

  Common files Oracle WebCenter content management 11.1.1.8.0

  Oracle Content Server 11.1.1.8.0

  Content of Oracle 11.1.1.8.0 Server component

  Content access Content Server Oracle 11.1.1.8.0

  Access to the contents of the Oracle Content Server 11.1.1.8.0 files

  Oracle Content Server Core 11.1.1.8.0

  Oracle 11.1.1.8.0 server content distribution

  Oracle extended Windowing Toolkit 11.1.1.7.0

  Oracle Fusion Middleware Admin Config 11.1.1.6.0

  Oracle Help for Java 11.1.1.7.0

  Oracle Help for the Web - UIX 11.1.1.7.0

  Oracle Help for the Web Shared Library 11.1.1.7.0

  Oracle Help share library 11.1.1.7.0

  Ice browser Oracle 11.1.1.7.0

  Oracle IRM                                                           11.1.1.6.0

  Oracle extended JFC Windowing Toolkit 11.1.1.7.0

  One-time correction of Oracle 11.1.0.9.9 installer

  Oracle outside in technology 8.4.0.0.0

  Oracle Remote Client of Intradoc 11.1.1.8.0

  Component of Oracle 11.1.1.7.0 rules

  Oracle SOA 11.1.1.7.0 workflow

  Universal Oracle install 11.1.0.9.0

  Oracle Upgrade Wizard 11.1.1.8.0

  Oracle Upgrade Wizard 11.1.1.8.0

  Upgrade Oracle WebCenter content management 11.1.1.8.0 Assistant

  Oracle WebCenter Capture 11.1.1.8.0

  Oracle Webcenter content - rights 11.1.1.7.0 documentalist

  Oracle WebCenter content - Universal Content Manager 11.1.1.8.0

  Oracle WebCenter content management install 11.1.1.8.0

  Oracle WebCenter content 11.1.1.8.0 management product suite

  Oracle WebCenter content: Imaging 11.1.1.8.0

  OracleAS Documentation 11.1.1.8.0

  There are 40 products installed in this House of Oracle.

  Interim plates (2):

  Patch 18188143: applied the sea Mar 19 17:37:32 BRT 2014

  Patch ID: 17263162

  Created February 5, 2014, 12:56:41 pm

  Bugs fixed:

  15872313, 17184457, 17515691, 16633496, 14317920, 15991141, 16892410

  14071471, 17929776, 13414481, 16042293, 17018964, 17627211, 16768600

  16037162, 14521663, 17768056, 14738077, 16460053, 17567819, 17806416

  15905591, 16080297, 17569908, 17043756, 18139768, 17211093, 17805499

  16418434, 16828356, 16671687, 17039391, 16698130, 17943394, 17632731

  17560900, 14246603, 15941347, 16045712

  Location of patch in the inventory:

  / app/Oracle/middleware/Oracle_ECM1/Inventory/oneoffs/18188143

  Patch location in the storage area:

  /app/Oracle/middleware/Oracle_ECM1/.patch_storage/18188143_Feb_5_2014_12_56_41

  Patch 18088049: applied the sea Mar 19 17:35:58 BRT 2014

  Patch ID: 17182855

  Created February 16, 2014 20:35:48 hrs PST8PDT

  Bugs fixed:

  17919101, 17894065, 17884570, 17883868, 17883112, 17854549, 17835742

  17832305, 17819213, 17812338, 17789722, 17783376, 17778867, 17761746

  17740542, 17733871, 17698852, 17658821, 17642431, 17636186, 17622384

  17616664, 17616611, 17616489, 17613656, 17608703, 17589960, 17581458

  17574153, 17567413, 17565564, 17558210, 17558068, 17546505, 17545841

  17540480, 17528590, 17514070, 17511368, 17511271, 17511089, 17501678

  17500375, 17475733, 17449617, 17421368, 17417817, 17416821, 17416807

  17416771, 17416377, 17416343, 17402732, 17401071, 17401052, 17397875

  17393920, 17393892, 17369286, 17368525, 17368096, 17362858, 17362130

  17354877, 17353764, 17352746, 17335303, 17335290, 17330493, 17324707

  17323595, 17323038, 17317268, 17314494, 17313064, 17313052, 17313000

  17312990, 17312933, 17312863, 17312366, 17298386, 17295962, 17290804

  17285105, 17270986, 17261952, 17255019, 17219134, 17216119, 17206903

  17201035, 17200854, 17199763, 17187804, 17185539, 17171852, 17171818

  17164502, 17160600, 17153780, 17074852, 17050451, 17049175, 17026301

  17008220, 17007746, 17007534, 17006378, 16999307, 16999291, 16991380

  16980256, 16980207, 16980196, 16979042, 16961904, 16958142, 16954858

  16941623, 16936055, 16936048, 16936036, 16936020, 16936006, 16935987

  16935976, 16921682, 16908287, 16858148, 16815976, 16796213, 13931337

  17424037, 17006115, 17171834

  OPatch succeeded.

  ==============================================================================================

  And contains the following configurations in config.cfg

  ==============================================================================================

  SocketAddressHostSecurityFilter = 127.0.0.1 | 0:0:0:0:0:0:0:1 | 192.168.1. * | 10.62.1.79

  xPortalSecurityPropagate = true

  Web server = javaAppServer

  AllowUpdateForGenwww = 1

  SearchIndexerEngineName = OracleTextSearch

  IndexerDatabaseProviderName = SystemDatabase

  AdditionalEscapeChars = -: #.

  FileEncoding = UTF8

  MaxQueryRows = 2000

  DisableAuthorizationTokenCheck = true

  IntradocServerPort = 4444

  SchemaPublishInterval = 604800

  SSAllowDelayedProjectWrites = true

  IdcServerThreadQueryTimeout = 120

  DisableQueryTimeoutSupport = false

  MaxSearchConnections = 20

  #Cache

  UseSearchCache = false

  #

  #AdditionalEscapeChars = _: #, -: {-}, has: A, GOLD: GOLD, CAN: CAN, AND: AND at the END:

  # Accesing a content item on a mapped Web URL (WebUrlMap) fails with the error: "unable to retrieve the content. Security access denied» (Doc ID 1639028.1()

  MaxAccountsInSecurityClause = 300

  # end (Doc ID 1639028.1()

  #Search fails for external users in WCC after upgrade to 11.1.1.8.0 (Doc ID 1676468.1()

  DoCaseInsensitiveAcctSearch = false

  # end (Doc ID 1676468.1()

  #MigrationFormatForfApplicationGUID = dCollectionName:dCollectionGUID

  ==============================================================================================

  To my UCM_Server1 content WebCenter.

  As I already have a WebCenter content I have to follow the second part of the note

  How to install and configure the UI content with WebCenter content 11.1.1.8.0 and 11.1.1.9.0 (Doc ID 1618305.1).

  Install and configure content WebCenter ADF WebUI against WebCenter Content Server

  Step 1) install the MDS schema

  (Step 2), install the Weblogic Server

  11 GR 1 material step 3) DOWNLOAD and install Oracle Application Development Framework (11.1.1.6.0) in the new WebUI WLS Middleware House, found here

  Step 4) Download and apply Patch 16, 546 129.

  Step 5) Download and apply Patch 16, 546 157.

  Step 6) download and apply the Patch and then 19,469,801, 18,102,108 Patch

  Step 7) copy the wccadf files in the field of user interface

  Step 8) Oracle on demand services (MDS) metadata registry

  Step 9) Place the WebCenter content domain user interface model

  Step 10) run the Setup Wizard on the new home of Middleware WebUI to create the new domain

  Step 11) updated the Oracle ADF of shared libraries

  Step 12) start the domain WebUI administration server

  Step 13) Save target Managed Server with the MDS repository and create the metadata partition

  Step 14) start the server managed WebUI.

  Step 15) associate UI WebCenter content to Content Server.

  Step 16) reboot the WebUI ADF server managed.

  Step 17 access the WebUI

  Step 18) complete the Configuration of the workflow

  Step 19) apply the latest Patch Bundle content UI of WebCenter

  MY DOUBT IS:

  To read the steps that I understood, to 19, with success, in the end, I will have an another WebLogic with a domain name and its respective EM.

  I have two servers weblogic?

  portal_domain (explained above) and a new wccui_domain wls and domain.

  This fix it?

  Two WLS to keep WebCenter portal and content, and other elements.

  Because I'm not able to do with the WLS even where I UCM_server1 today?

  Thanks for all suggestions and criticism.

  To read the steps that I understood, to 19, with success, in the end, I will have an another WebLogic with a domain name and its respective EM.

  I have two servers weblogic?

  portal_domain (explained above) and a new wccui_domain wls and domain.

  This fix it?

  Two WLS to keep WebCenter portal and content, and other elements.

  Because I could not do with the WLS even where I UCM_server1 today?

  Yes, up to 11.1.1.9.0, you will need to install a new wls House (new wls server admin) and then configure WCC ui there. User interface and COE will not work in the same field. You can have the portal and content under the same House of wls and install a new one for the user interface.

  This is due to a problem with ADF and WCC libraries.

  With 12 c, this dependence is not there, and you can install / configure all 3 (Portal, content and adf ui) applications on the same domain.

• Images imported into my Stadium go up as white and make each image before the image of thugs imported as red squares that fill the perimeters of the image which then renders the publication and test scene has useless Flash, what can I do

  I worked on the animation of a scene in flash for a few weeks and recently I met a problem with the import of my images to the stage where images I have import increase, however, the keyframe I tried to import the image to watch that it is occupied by an image and each image before the image key that just imported a picture that doesn't show shows up as a red square that fills the perimeters original of the image , there is no solution to this problem all where on the forum and the personal adobe technical support does not help me find a solution to this problem, what can I do to get Flash working normally again and fix this?

  After the first time that I publish a preview after I start using the flash, flash makes the publication and the test scene features as useless and claims he has not found an HTML template, or if the images if I import all the images on the stage who empties and display each image before the image as a red square and then try to publish a flash preview renders also the publication and the scene features test as useless and claims he has found none of HTML template. What can I do to fix this? There is no solution on the web anywhere to this problem either.

  I discovered the problem, I just need to get a Z820 with a Nvidia Quadro K6000 graphics card and a new Flash Professional subscription, I'm lucky, I did what I did. Thank you!

• How to cut and paste the image of the body of the received email

  I'm trying to cut and paste an image included in the bottom of an email and insert it into a Word document so that you can size and print. I can highlight, cut it with Ctrl C, paste it into the document Word with Ctrl V, but the image doesn't show, although the picture frame appears when I click on the place where the photo was pasted. Framework, but empty, no image. Any thoughts?

  Thanks to everyone for their help.

  The problem has been resolved - to try and finally understand everything.

  If you encounter this problem, it is perhaps because, unless you know the file format of the inserted picture, programs can not figure it out for you. Place your cursor on the image, right click and save the image under a .jpeg instead of simply copying. Then work with the file .jpeg in any photo management program you use normally - or even insert it in Word.

• Copy and paste the Images NOT working.

  When I click with the right button on an image and choose 'copy image' and then try to paste in my editor, all I get is a string of text that represents the location of the image, as if I had chosen 'copy image location' instead. What gives?

  
  

• Qosmio G20 and Acronis True Image

  Hello

  I have a G20 with the media library and twin 100 GB hard disks that are configured to act as two separate discs (set up of RAID options when I reinstalled the system). I have programs on a disk (C) and the operating system and my data on the other (D).

  On a previous thread I asked to retrieve the C drive only from the recovery disks without wipe data on the D drive, and it seems that this is not possible, to remedy this, I decided to follow the suggested advice and create an image of the C drive for later retrieval if necessary. However, I have had a problem of creating an image or a clone of my system using Acronis True Image disk and wonder if anyone can help. I replaced the D drive with a new disk of 120 GB and uses the old drive in a USB enclosure sata to store the clone or image recovered.

  First of all, all devices, readers ext usb, wireless keyboard, cable network & second screen are connected through a hub to a USB docking station, and when I try to clone with this joint, it fails to restart. Undeterred, I took off the hub and the clone for the external drive seems to work very well. However, when I remove the drive from the existing system and replace it with the clone to test, it does not work. The system appears to start but then get the screen where it says windows windows had a problem and I want to start in safe mode, last known working system, or start as usual in any case. If I select it just reboots and gets back to this screen.

  Also, I tried to create an image rather than a clone and recover the image on the hot spare. Once again, it seems to go ok but when I put the disc and satrt to the top of the same thing happens.

  I don't know if there is anything that you must close before imaging or cloning as the instructions don't say, so don't know if theres nothing running that may affect it. The instructions are pretty basic but seem pretty simple, so I do not see where I am going wrong.

  Does anyone have experience of this type of problem and how to fix it.

  Thank you very much

  A few months ago I acquired a regular copy of Acronis True image for my G20.

  After that many negative attempts to use the program, who do not recognize the disks
  I asked for help using Acronis
  which solves the problem brilliantly, sending me a special version on purpose
  for the difficult features of the Qosmio system.

  If you an e-mail to the Acronis media, they probably have in the Archives of the version
  for the Qosmio G20.

• Tecra S1 - USB ports (all) and card reader does not

  Hello

  Just got a 2nd user Tecra S1. I was told that the drive SD card and USB ports do not work. Card reader (and card PCMCIA USB ports) works as well as the ps/2 port.

  Any ideas anyone? USB ports turn on power on indicators key USB etc but nothing is recognized under XP.

  See you soon

  Hello

  Maybe the USB ports listed in the devices with exclamation points Manager yellow. Did you check that?
  In addition, I would recommend updating the chipset driver. Visit the Toshiba site for an update:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  If you also received a Toshiba Recovery disk you may have to use it. The HARD disk will be wiped and XP will be installed all the drivers and tools.

  Good bye

• retrieve and record continuous images in labview

  Hello

  I use the NI 1744 smart camera to capture and record continuous images of a moving object. My smart camera is detected in MAX and made the seizure of an image. But when I use the attached file of VI in labview, the smart camera is not detected, only the webcam is detected and a video can be generated using the webcam. Please help me detect the NI 1744 smart camera. I will be grateful.

  Hello

  Your smartcam is not directly accessible from your PC because it is a remote device.

  Create a project in real time to access your camera.

  Have a look here: http://forums.ni.com/t5/Machine-Vision/Error-1074397145/m-p/535230/page/2?view=by_date_ascending

  Concerning