Perfomance and the technical Configuration of the CPSA
HelloWe are running CPSA with a RAC configuration (all on one server), 11.5.10.2.
We have around 300 000 point org assignments (20 inventory orgs). Performance plan has been very slow sometimes (sometimes takes 5 hours to finish).
I noticed a lot of customers have 2 servers running (one for the transactional system) and the other for the planning server.
Can anyone tell if getting another server for the planning server is the recommended approach? Should use us a 64-bit Planner? We run Linux and noted the 64 engine bits of planning only is not supported for Linux (maybe we could get a different server with a different operating system that is supported for 64-bit planning).
What is the best way to get the best out of the centralized approach that we use currently (with CARS)? We have indicated that we can run the planning CAR engine in all cases (it must run separately in another simultaneous Manager unrelated to the RAC).
Any comments on the above would be greatly appreciated.
Thank you!
Hello
WRT to your questions
1. it is only limited by the amount of physical memory on your machine
2 64-bit Planner will give you no performance gain. In fact if you run the plan with the 32 bit job scheduler and planner of 64-bit on the same machine, then you will notice that the 64 bit version is still a bit slower (although hardly noticeable).
The main advantage of using the 64-bit version is:
1. ability to use large amounts of memory and thus execute plans big CPSA
2. the ability to have the plan to calculate a number high (for example, order sizes, usage, etc.)
3. it is difficult to determine what is the cause of your performance problem without looking at the program installation/data. Several factors can influence this. for example, options plan (constraint without constraint, decision, rules, etc), modifiers command combined with strong demand, the profile settings
Also, you mention an autonomy of 5 hours. For the Scheduler itself or that it also includes the phase of snapshot? If your performance problem is in the module itself, a faster processor will help on this side.
My recommendation is that you (as much as you seem to be still in test) is to ensure that you are on the last engine code to avoid any known performance problems. See the notes 252108.1.
If you are on the last code, so my next suggestion would be to log a service request with the support of your data. With your flat files MBP (see note 245974.1, section 4) support can test the performance of your plan on their machines.
Best regards
Geert
Tags: Oracle Applications
Similar Questions
-
ERPI configuration: data server and the physical schema
Hello
I use ERPI11.1.2.1.
I try to configure ERPI following the documentation of erpi_admin.
It is said that to create the database server and the physical schema for ERPI, I must develop 'ERP Integrator' in the tab 'Physical Architecture' in the Manger of the topology of the ODI.
But I have no 'Integrator of the ERPI' node 'Technical' below in physical architecture :-(
Thanks in advance for your help
FannyYou need technology that works on the basis of data of the ERPI. So if your the ERPI on Oracle database, expand the Oracle technology and then right-click and choose Insert database server.
-
After you have opened an email 3 windows appear. Then the email itself - a second window showing technical information to e-mail - code source, sender, etc. and the third window showing the e-mail message. You want to close the second window, with technical information and simply keep the sender information and the message itself. How can I fix this problem?
Thanks for the help.View (Alt - V) - headers - Normal
-
Is it possible with the serial number of an Xserve to read the configuration and the year of production?
This will show you the model and year: https://checkcoverage.apple.com/
If a specific configuration (like the 1 TB disk instead of 500 GB for ex) will not be determined. You can only learn by starting the Xserve (or open and look into it.)
-
I have an Acer PC Windows 7 with an AMD Athlon X II processor, 4 GB of RAM.
I have Photosmart C309g and everything-each 7510, both connected via wi - fi, using different IP addresses that are not in conflict with other devices on my network.
I executed the complete installation for both HPs.
I can print either, but I can scan only using the 7510.
When I open the HP scan diagnostic, it does recognize that the 7510 - the c309g is not yet listed.
I noticed only 7510 application record contains a HP scan application and it also recognizes that the 7510.
There is no application scan c309g folder. I tried Win 7 Windows Fax and Scan application but that also recognizes as the 7510.
1. is there a way to configure the system so that it can print and scan from these two Photosmarts?
2. If the scanning using a 7510 and c309g does not work, could I use a 7510 both a 7520?
Hello Osiris43,
Welcome to the HP forums! I understand that you are unable to scan a document using the Photosmart Premium C309.
You should have two printers scanning capabilities, because they have a different software. The Photosmart printer using the Solution Center and the Photosmart 7510 uses the Printer Wizard.
I suggest you uninstall/reinstall the software Photosmart Premium C309. Please follow these steps:
Please follow this HP document uninstalling the software of the printer.
Then, perform a clean boot on your computer. I'll give you a Microsoft document on this step here.
Now, install the full features on the site of HP software here. Choose your operating system that is appropriate; 32-bit or 64-bit.
Once installation is complete, please click on the document to Microsoft, and "how to reset the computer to start normally after a clean boot."
Please send me your troubleshooting steps.
-
Time capsule 'unexpected error' despite the reset and the IPv6 local link configuration
Hello
I try to use a time capsule that I have not used for a long time to backup my mac.
I have adware on chrome and safari that I cannot get rid of (trovi) despite several attempts (extensions, resets etc.)
I decided to upgrade to el capitan, so that I could use software removal that does not work on Lion, but now I can't save because time capsule gives me "error unexpecetd".
I have reset the TC and I configured link-local IPv6, but am still having the same problem.
Anyone know if it is a question can be resolved?
Thank you!
It is possible that software that you download to help get rid of the adware etc... blocking the work TM... affects a lot of bad a antivirus software on Mac OS. McAfee is one of the worst.
What operating system are you currently using?
There is no need to upgrade... but it is necessary to clean install.
Download and use Carbon Copy Cloner. You can use it for free for a month... I highly recommend you do the backup on a USB key connected to the Mac, so it can be made bootable... and then can be tested immediately.
You can use the TC and the backup to that... but you can't boot from network drives.
I can recommend you to do a clean install... just wipe the mac and start again... It's extremely better than any software removal tools.
-
Update Windows 7 updated the guard and does not configure updates
Original title: 2 Windows updates daily for the last 10 days
I get 2 updates every time that I stopped for the night. The updates take anything between 3 and 5 minutes to install and the pc is turned off automatically. When I restart the pc it starts immediately configure updates and it can take anything up to ten minutes. I don't know how to access the updates of teas to see if they are fresh updates or if they the same two updates recurring constantly! This 'problem' started ten days ago.
Click Start, type: Windows Update
Press enter on your keyboard
Click on the link to check updates
A list of all the updates is downloaded
You will be able to view the updates that must be installed, along with a description and the number of KB.
You can then choose to go to http://www.microsoft.com/downloads and download these updates manually and install them.
You can also click on change settings in Windows Update and click the option to download updates, but choose when to install them.
Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP
-
Configuration of the Windows stuck at 67% updates then restarts and the entire process loop
Original title: configuration of updates
My computer starts to try to configure Windows updates immediately I turn it on and gets to 67% and no further. Finally, it restarts and start the process again without success. All this takes 11/4 hours before I can connect on the Internet. This happens only in the last 3 days.
Hi didi45,
1. the updates Windows tried to install?
2. don't you make changes to the computer before this problem?
You can read the following article and try the steps.
The update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista and Windows 7
http://support.Microsoft.com/kb/949358
Hope this information is useful.
Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Hello! Recently, I installed Wubiand appreciates well. However, a few days ago, when I tried to boot XP on my netbook (EEE PC 1005hab), it restarts just constantly return to the selection screen of the BONES. I tried Safe Mode and last good Configuration known with anything will do. What should I do now? Ubuntu has not stopped working suddenly, so I can't access my data.
I don't have to have a Windows XP CD, there is something weird Asus recovery instead. In addition, it is a netbook so I don't have an optical drive to run the recovery CD. I'm doing a Livecd of Linux USB so I can back up my data... but I can do but reinstall at this point?
Thank you.
The afflicted system has a working CD/DVD drive (even an external).
You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?
If there is a problem starting, XP is configured to automatically try to start again and you can stuck in a loop not being able to go beyond the screen boot options, or none of these startup options you choose will work only.
Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again. You have tried them all!
The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.
If this is the case, you must call Options menu advanced boot yourself until you do not see the option:
Disable the automatic restart in the event of system failure
When you get the XP Advanced Options correct start menu, it has options on it like these:
Safe mode
Safe mode with networking
Safe mode with command promptEnable Boot logging
Enable VGA mode
Last good Configuration known (your most recent settings that worked)
Directory Services Restore Mode (Windows domain controllers only)
Debug mode
Disable the automatic restart in the event of system failureStart Windows normally
Reset
Return to OS Choices MenuYou need to choose in this menu is the option:
Disable the automatic restart in the event of system failure
Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.
If you miss the window of opportunity F8, you must try again and start pressing the F8 key with more urgency (earlier and more frequently) until you see disable automatic restarts on system failure, and then select it.
You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.
Answering queries and results report of the disable automatic restart on system failure screen and you can decide what to do next.
Do, or do not. There is no test.
I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!
-
After uninstalling my XPSp3 o.e., I started getting the following error message: "the address book failed to load. Outlook Express is incorrectly configured, please re-install. "at the start of XP and the machine.
Uninstalling included 7 entries registry to remove all the * files dbx and files *.wab addressbook, except himself. After uninstalling and receipt of the error message above, I tried to use my CD of XP OS to re - install O.E. as a component of Microsoft without success.
I upgraded to Outlook 2007 and imported to the address book of O.E. successfully before uninstalling.
Please advise me how to get rid of the error message always appearing at startup.
Thank you
You can't really uninstall and reinstall OE without having to reinstall XP as OE is a part of it. I hope your foray into the registry does not require a reinstall of XP.You now have the DBX files? WAB files?If Outlook has been on your machine before this event, see the reference by PA Bear in this thread
http://social.answers.Microsoft.com/forums/en-us/xpnetwork/thread/a8c8cf17-d792-481e-BCCA-13b03852a995If Outlook has not been installed, see these.All of you who have the same cause. Something is screwed up with your address book.It could be several specific problems, which include:
-corrupted WAB file
-damaged or incompatible DLL files for the addressbook
-have OE set to use the Outlook98 / 2000 + contacts instead of the WAB
folder and there is something wrong at the end of OutlookFor more details, take a look at:Error message: the Message could not be sent. Some invalid recipients
(Outlook Express: there was an error opening this message)
(The address book failed to load. OE is configured incorrectly)
(Corrupted or incompatible WAB32. DLL file)
http://support.Microsoft.com/?kbid=239135
OLEXP: Error Message: failed to load address book
(There was an error opening this message)
http://support.Microsoft.com/?kbid=269777
http://support.Microsoft.com/?kbid=310873
OLEXP: MSIMN has caused an IPF in Module Wab32.dll
http://support.Microsoft.com/?kbid=247706
Error message: failed to load address book, Outlook Express is...
http://support.Microsoft.com/?kbid=191946
Error message: could not open address book, a component is missing
http://support.Microsoft.com/?kbid=192321The address book Windows (WAB)
http://www.insideoe.com/files/WAB.htmTo share Contacts between Outlook and Outlook Express
http://www.slipstick.com/contacts/oeshare.htm -
original title: my windows vista will not except the automatic updates and the system starts it will only configure the process which can be done to solve this problem
my windows vista computer will not except the automatic updates and when the system starts it will only configure the process which can be done to solve this problem
Hi Glennisidore,
Try running the fixit http://support.microsoft.com/kb/971058 in aggressive mode and see if, after the reboot, you are able to perform your edits again.
-
After using no not my laptop for some time, I turned on and 53 updates to Windows Vista. Went through the whole process, then got to the updates configuration screen and the laptop keeps restarting and it won't do anything else.
Hello
1st thing to try is a restoration of the system in safe mode
http://www.windowsvistauserguide.com/system_restore.htm
Windows Vista
Using the F8 method:
- Restart your computer.
- When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
- Select the Safe Mode option with the arrow keys.
- Then press enter on your keyboard to start mode without failure of Vista.
- To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
- Do whatever tasks you need and when you are done, reboot to return to normal mode.
If that does not read this information
the link below is how to download and get a vista disk startup repair, which you can start from the
http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/
Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below
http://www.bleepingcomputer.com/tutorials/tutorial148.html
to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start
It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu
Change boot order it do dvd drive 1st in the boot order
http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/
___________________________________________________________________
or please repost your question in the correct windows update forum
http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all
-
SanDisk Extreme SDSSDX 120g Corsair mid-tour COOLER MASTER Hyper 212 Plus CPU CORSAIR 750W MW7 G.SKILL Ares series 8GB (2) ASUS P8Z77-V PRO LGA CPU Intel Core i7-3770 LG DVD writer black SAPPHIRE HD 6850 WD Caviar Black (2) RAID 1 I had this problem.
While problem dialog box was displayed on the screen, I did a Ctrl-Alt-Del and brought up in the Task Manager.
I went in the process, found tab the configuration process ASUS and my mouse right click.
I chose "Open file location" and a display of the tree indicates that the associated file is at C:\Windows\Install.
I opened Windows Explorer and went to C:\Windows\Install.
I found 3 files at the root of this folder that began with asus/ASUS.
I deleted the files of 3 three who started with asus/ASUS.
I disconnected and when I came back to my office that the pop-up did not reappear.
I stopped and restarted and the pop-up did not reappear.
-
Need a Clarification on the installed component and run Simulator Configuration
Help!
I need clarification on what the plugin Eclipse is telling me. There are two parameters that are confusing me. For components installed (found under preferences/Window/BlackBerry JDE/Installed Components), I have a choice of 5.0.0 4.7.0,4.6.1, 4.6.0 4.5.0 and 4.3.0.
Depending on which component I select when I go in the tab Configurations.../Simulator/course walk, I see a different mix of devices. In all cases, there is a default Simulator.
Initially, I assumed that each JDE component supports a mixture of different devices, and that is it compiled correctly, I would be assured that the app would work for all devices on the tab run Simulator Configuration. In my tests, I found theopposite. I also assume that, for each component of the JDE, there is a 'default' Simulator that was representative of all devices in the drop-down list run Configuration Simulator. In my tests, am not sure what actually represents the Simulator 'by default'.
Can someone clarify how to JDE and Configuration simulators run installed interact and a developer show how to ensure that their application is running on a mix of devices?
When I finally get to the point where I am ready to deliver, what are the points of decision of installation? Is it enough to simply require a specific version of an operating system (for example 4.7?) or do I have to create a grid and check the two model number and version of the operating system?
Thanks for your help.
"currentT shipping Curve 8330 come with OS 4.5" - they must be, as far as the carrier released a version 4.5.
"Your statement that most consumers do not upgrade surprised me too" - only I support! You might get a different opinion of someone else. But the question is why would? And our world app downloads indicate that he is did not upgraded phones out there.
"I guess you are right in this assumption of statementI you are right in this statement"
What is - an appropriate version of the BlackBerry JDE
Article number: DB-00537
http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800738/800901/What_Is..."If there is some Curve 8330 there running 4.5 OS, it's a configuration supported." - correct
"Construction of the 4.3 OS will be one where the menu appears in the upper right and the built 4.5 OS will be one where the menu is out." Sounds good
-
I'm trying to get the HelloWorld application to work, but I can't find the IP address and the option of setting the password for the simulator of tablet in the run/debug configuration. It should be in run/debug configurations, but it's not.
I already have the Simulator works and correctly installed the Playbook SDK (link to version 2.5 SDK and Flash Builder). I have no error in compilation (QNX namespaces are used), I think that the installation has been correctly executed.
Please let us know if anyone has the idea to solve this problem.
Please see below the screenshot associated to above posted the question:
Sometimes last discussions stressed that some dialog size is bad, and if you resize, you will see where the password field is. Is that what you face here?
Maybe you are looking for
-
I have a laptop HP G56-114SA.
There is a fault coming up to replace the main battery! Where this battery. Thank you.
-
I lost my printer drivers for Photosmart C7280 and download of HP website below seems to be corrupted. Help? Action: Your software print driver is missing or a better version available. HP recommends the following software. Click on the link below t
-
Is there a way to put my ITunes in a music file so that I can upload in a non-Apple device?
I want to download music on a phone that is not an Apple product. Is it possible that I can do some kind of music file that I can then load on my phone?
-
iOS 5 will not refresh :(
Hello I tried several times to update to iOS 5 on iPhone, but it takes 10 minutes (even with BT infinerty!) and then it bloody says: 'connection time out, check network connection' Grrr! Checking as much as my limited intelligence doesn't let me, dia
-
Im trying to set up remote access for a babyphone Foscam (Fl8918W). I worked on it all day. No matter what I do, I can't get the camera to get on my computer (or iPhone). Here's some of what I've done so far... -Camera configuration and find the IP