Photosmart C7250 is incompatibility with windows 8.1 Overview operating system.

Similar Questions

• Incompatibility of printer Epson LQ-680 with Windows 7, 64-bit operating system

  Incompatibility of the printer Epson LQ-680

  I got a new machine (with Windows 7, 64-bit operating system).

  Earlier I had been using an Epson LQ-680 with a serial cable.

  The new machine has a USB port, so I have to use a USB to PS/2 port.

  I installed the Energon USB but still cannot print.

  Incompatibility of the printer Epson LQ-680

  I got a new machine (with Windows 7, 64-bit operating system).

  Earlier I had been using an Epson LQ-680 with a serial cable.

  The new machine has a USB port, so I have to use a USB to PS/2 port.

  I installed the Energon USB but still cannot print.

  I read your post with a lot of attention. There seems to be some confusion on your part. I want to arrempt in order to clarify the information so that a good solution might be found for your needs.

  The Epson LQ-680 is a matrix printer with a print head 24 pins. It is designed to use a parallel port. This means that its computer interface conforms to the IEEE 1284 specification. This is often referred to as a Centronics parallel port. Series No.

  http://www.Epson.com/cgi-bin/store/support/supDetail.jsp?BV_UseBVCookie=Yes&OID=14331&infoType=overview

  Thus, because your computer does not have a port for a direct connection, you must use a parallel to USB device.

  Not all of these devices are supported printers. Please check the specifications of the device that you use to connect your USB printer and confirm that it supports the printers. It is preferable that it supports bidirectional printing through the device. If it is not the case, getting the arrangements put in place for this printer could be a problem.

  Driver for printer:

  http://www.Epson.com/cgi-bin/store/support/supDetail.jsp?BV_UseBVCookie=Yes&OID=14331&prodoid=61441&infoType=downloads&detected=Yes&platform=OSF_W_7-64

  =================

  You did not mention whether your machine is a laptop or computer desk/workstration. If the latter, and if she will allow to install PCI cards or PCI-E, install a parallel port card would work more simply.

  If you want other help, please let us know the make and model of the parallel to USB device.

• I have a Photosmart B109a with Windows Vista as the operating system. I can't print any documents.

  When I go to print a document, the appropriate box comes up to a selected number of copies etc., the printer connects correctly and then sounds like it is printing. Nothing is printed in fact when the paper comes through.

  Just in case it was a fault of the printer, I reconnected it a Deskjet HP's 803C and it is the same thing. The additional mystery is that the images print perfectly. I use Microsoft Office 2010 for documents. All ideas

  Thank you for your reply and my apologies for not recognizing sooner. However, problems went much deeper when my computer crashed. Hard drive kept saying that it was full and therefore would not accept certain instructions. All now corrected with a new hard drive which has solved printing problems. Thanks again.

• I want to upgrade Windows XP Professional to Windows 7. However, I have an old Windows Picture It Photo of 2001 (not 2002) I want to lose. I'll be able to install this program with Windows 7 as my operating system?

  I would like to be sure I can install my Microsoft Picture It Photo (copyright 1997-2001 version) on a new computer running Windows 7.

  Run the Windows 7 Upgrade Advisor and check this program in the Windows 7 Compatibility Center .

• I just bought a new computer.it has windows 7 64 bit operating system, it is good with the exception of my call of duty games running, they used to run very well on my windows vista 32 bit system, what is the problem?

  There are video games that are compatible with windows 7 64 bit operating systems?

  Hello Peter.

  Yes almost all games in 10 years works perfectly on 64-bit Windows.  What Call of Duty games are you having problems with?  If the first two, you might have to enter the video drivers for your graphics card/computer manufacturer as the first two required OpenGL which is not included with the drivers that Windows uses by default (this has been the case since at least Windows XP).

  Paul Smith - MVP for Windows desktop experience... I crawled off NNTP - for now. Detachment Aldershot, United Kingdom. On the internet at windowsresource.net and dasmirnov.net. Please post back to let us know what works and what does not. :-)

• My canon EOS 20 d is not detected by my computer lenovo, OS Windows 7, 64-bit and my computer Gateway Laptop windows vista 32 bit operating system

  My canon EOS 20 d is not detected by my computer lenovo, OS Windows 7, 64-bit and Gateway laptop with Windows Vista 32 bit operating system.  This means plug-and-play is not available or does not so I have to use for my compact flash card reader to transfer pictures.  I've already updated the firmware by downloading the upgrade of the Canon website.  I tried to turned touble this problem following what is suggested in the Canon Website, and still the problem is not corrected.  Thank you.

  Hello

  Follow the steps mentioned below and check if the problem persists.

  Method 1: Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: You can also try to connect the camera to a different port and check if it helps.

  Method 3:  You can also try changing the normal mode to print/ptp in camera mode where you can print directly from camera by connecting printer directly using the usb cable.
   
  Hope this information helps.

• HP Photosmart E317 is compatible with Windows 7?

  HP Photosmart E317 is compatible with Windows 7? How to download pictures from the camera?

  Hello

  Using the memory card on your camera or only the internal memory?

  (a) memory card: out the card and put the computer card reader, he'll end up as a drive and you can copy photos nearby.

  (b) for memory internal: you can use the USB cable provided with the camera, but it can not be found in Windows 7. One option is to buy a memory card, move pictures from the memory on the card to it and again to (a) above.

  http://h10032.www1.HP.com/CTG/manual/c00492399.PDF

  Kind regards.

• Microsoft Picture It incompatibility with Windows 7 and the alternatives for the .mix files.

  I have been using Microsoft Picture It for years to design a ton of graphics for my business and now I bought a new pc with Windows 7 and find that my true love Picture It! is not compatible.  I never dreamed that this would be the case for a software that is not even a decade or just spent thousands on the new pc would sit immediately to the store that it came.  I really feel that Microsoft has cheated me on something that I paid for and invested so much work making it unusable, and it brought my small business to a standstill.  What other program is available that is compatible with Windows 7 that will allow me to edit and view existing and another .mix Picture It! file format and contain all the features of Picture It?  I'd be willing to buy other Microsoft software to Picture It compatible with Windows 7 if necessary.

  Hi all

  I know you are all disappointed that Microsoft Picture It is not compatible with Windows 7.

  Your comments would be better heard if you send to the site Windows 7 comments.
  http://mymfe.Microsoft.com/Windows%207/feedback.aspx?formid=195

  Here are your options when the software is not compatible:

  If the program is not compatible, then you try to install and run the program in compatibility mode.

  Use the following steps:
  (1) right click on the program
  2) click Properties
  3) click on the Compatibility tab
  (4) select run this program in compatibility mode and select Windows XP, Windows Vista or other operating system, the program has been run successfully.

  Check out the link here: make sure to run older programs in this version of Windows
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  If you are running Windows 7 Professional or Ultimate version, install Windows Virtual PC and Windows XP mode (http://www.microsoft.com/windows/virtual-pc/default.aspx) and run your software in Windows XP.

  If you run Windows 7 Home Premium, try VirtualBox (www.virtualbox.org) or VMware Player
  (www.vmware.com) or any other virtualization 3party software and install a separate copy of Windows XP (family or professional edition) for this purpose. You can find the virtualization software free that will run on Windows 7 Home Premium.

  Sincerely,

  Marilyn

• With the help of an operating system older Compaq is professional Windows. Internet Explorer connected very slowly. .

  With the help of an operating system older Compaq is professional Windows. Internet Explorer connected very slowly. SO I've reworded in safe mode with network and IE has worked very well. I installed Mozilla Firefox and then restarted in normal mode. Then Internet explorer would not connect. How to diagnose in safe mode. What does safe mode or safe mode with network do to help diagnose? Can someone help me solve this problem? Any help would be appreciated thanks in advance.

  Hi, Raymond J,.

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         What type of internet connection do you use?

  ·         What security software do you use?

  Follow these methods.

  Method 1: As the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

  Method 2: Follow the steps in the article.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  How to reset the Protocol Internet (TCP/IP)

• SQLite3-wal-point control cannot be in SQlite3.dll library message appears at startup with windows 7 starter 32-bit system.

  SQLite3-wal-point control cannot be in SQlite3.dll library message appears at startup with windows 7 starter 32-bit system.

  Don't worry about this - I fixed it by following the steps below...

  Thanks anyway! :-)

  1. Temporarily close the anti-virus software and firewall
  2. Open the control panel configuration, programs and features or Add (and remove programs) and go to the section uninstalling
  3. Remove all Apple products in this order - iTunes, Quicktime, Apple Software Update, Apple Mobile Device Support, Hello, Apple Application Support.  You don't need to remove Safari
  4. Restart the computer
  5. Go to Apple.com and download the latest version of iTunes
  6. Re-install

• Hello. I'm having trouble installing my Photoshop CS3 software. I use a PC. My computer recently had a virus and the it consultant all deleted and reinstalled Windows Start program with all updates. My operating system

  Hello.

  I'm having trouble installing my Photoshop CS3 software.

  I use a PC. My computer recently had a virus and the it consultant all deleted and reinstalled Windows Start program with all updates. My operating system is "Microsoft Windows 7 Home premium 2007 - with updates added.

  The version of photoshop that I have is 'Adobe Photoshop CS3, 2007. I installed Photoshop CS3 which seemed to install properly. I activated the dics and inserted the serial number. Activation complete. I had a problem with the registration with the following message through "a problem has been experienced so he was trying to send information on the internet".  I had a problem with look at a. CR2 file but I got a converter of Microsoft 'CameraCode '. I can use Photoshop software. I can't use a software link with Photoshop CS3 I was using before. It's "NIK software - Silver Efex Pro". This means that on the section "filter Photoshow. Can I use the software, but it does not save the changes I made. When I turn off the computer Photoshop CS3 is deleted from my computer. I got LIGHTROOM but software that works very well.

  The summaries. I can load Photoshop and use and save the changes, but when I turn off my computer the software is removed from the hard drive. But I can't get the link software - Nik software - Silver Efex Pro. Please can you advise me what I should do to get my software working properly again.

  Thank you.

  Keith Fernandez

  Once the software is installed, it will not be removed under normal circumstances.

  I do not know if your computer is still infected and it is removed or the problem is that you can't 'see' photoshop' but it is always installed.

  to verify this, check the installation directory and check its size on your hard drive.

• Hello. I'm having trouble installing my Photoshop CS2 software. I use a PC. My computer recently had a virus and the it consultant all deleted and reinstalled Windows Start program with all updates. My operating system

  Hello.

  I'm having trouble installing my Photoshop CS2 software.

  I use a PC. My computer recently had a virus and the it consultant all deleted and reinstalled Windows Start program with all updates. My operating system is "Microsoft Windows 7 Home premium 2007 - with updates added.

  The version of photoshop that I have is 'Adobe Photoshop CS3, 2007. I installed Photoshop CS3 which seemed to install properly. I activated the dics and inserted the serial number. Activation complete. I had a problem with the registration with the following message through "a problem has been experienced so he was trying to send information on the internet".  I had a problem with look at a. CR2 file but I got a converter of Microsoft 'CameraCode '. I can use Photoshop software. I can't use a software link with Photoshop CS3 I was using before. It's "NIK software - Silver Efex Pro". This means that on the section "filter Photoshow. Can I use the software, but it does not save the changes I made. When I turn off the computer Photoshop CS3 is deleted from my computer. I got LIGHTROOM but software that works very well.

  The summaries. I can load Photoshop and use and save the changes, but when I turn off my computer the software is removed from the hard drive. But I can't get the link software - Nik software - Silver Efex Pro. Please can you advise me what I should do to get my software working properly again.

  Thank you.

  Keith Fernandez

  Hi Keith,

  You won't be able to re - install using the discs and the number of series that you used initially, but we have a solution.

  The activation for more server CS2 is no longer in service. For this reason, we did a version of these titles of software available that doesn't require activation. This is for users who already buy the software.  For more details and specific links for the software, please see the following link:

  Activation server stops for Creative Suite 2 and Acrobat 7 product Macromedia

  Instead of your old serial number, use the one shown next to the download link: download Acrobat 7 and CS2 products

  Guinot

• excelreportdemo project link error with CVI2010 on windows 7, 64-bit operating system

  I try to run the project for excelreportdemo in CVI2010 on windows 7, 64-bit operating system. I have the Excel2013 installed as well. I chose the build configuration release or debug for 32 bits of the system in order to be compatible to the test for the production platform.

  However, I get errors in link project 12 as follows:

  Undefined symbol '_ExcelRpt_RangeBorder@24' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_WriteDataFromTableControl@16' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_SetCellValue' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_SetCellRangeAttribute' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_ChartAddtoWorksheet@40' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_ChartWizard@52' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_SetChartAttribute' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_WorkbookNew@8' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_ApplicationNew@8' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_ApplicationQuit@4' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_WorkbookClose@8' referenced in "excelreportdemo.c".
  Undefined symbol '_ExcelRpt_WorksheetNew@12' referenced in "excelreportdemo.c".

  I found a previous discussion in 2007. Unfortunately, it did not help for the same problem on my new machine and CVI2010. Could someone give me help on that.

  Thank you!

  Yuwei

  I get it worked after that I removed the excelreport.fp in the Menu library customize. The excelreport.fp has been added to the Menu library customize to my other work on the project, which, but had similar problems. It seems CVI is getting better and better, so that you don't need extras like it was before. Do not add reduntant libs.

  

• Where can I get a driver bluetooth on HP Pavilion g6-2260us windows 8(64 bit) operating system

  Where I can get a bluetooth on HP Pavilion g6-2260us windows 8(64 bit) operating system driver. It doesn´t appears in the settings.

  Hello:

  Your model does not come with built-in bluetooth technology.

  Here is the link to the product for your model specifications page.

  If it came with bluetooth, which would have been listed next to the section of wireless connectivity, as well as the wireless card.

  http://support.HP.com/us-en/document/c03595184

• HP Pavilion DV6-C80EL HD 7690 M XT graphics card. Windows 7 64-bit operating system

  I have a PC HP Pavilion DV6-C80EL, with HD 7690 M XT graphics card. Windows 7 64-bit operating system

  B0B34EA TYPE S/N {removed privacy}
  I have try the card READER was updated to use windows 8
  HP told me to turn to AMD.
  AMD housewrap me to turn to HP.
  What should I do?
  THE PC was purchased in June 2012.
  Thank you

  HP has released a disc for the PC in question, associated with 64-bit Windows 8
  Greetings

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4132 & LC = IT & CC = IT & DLC = IT & sw_lang = & Product = 5212723