PIX is the VPN address

Similar Questions

• Tunnel VPN IPSEC Gre of the router in the branch office by Pix to the router HQ

  Hi all

  I tried to get this scenario to work before I put implement but am getting the error on router B.

  

  01:05:38: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 83.1.16.1

  Here are the following details for networks

  Router B

  Address series 82.12.45.1/30

  fast ethernet 192.168.20.1/24 address

  PIX

  outside the 83.1.16.1/30 interface eth0

  inside 192.168.50.1/30 eth1 interface

  Router

  Fast ethernet (with Pix) 192.168.50.2/30 address

  Loopback (A network) 192.168.100.1/24 address

  Loopback (Network B) 192.168.200.1/24 address

  Loopback (Network C) 192.168.300.1/24 address

  Is could someone please tell me where im going wrong as I read the explanation of the error and it points to political unmaching. This has confused me like the two counterparts seem to have the same settings.

  Config router B

  ======================

  name of host B
  !
  Select the 5 secret goat.
  !
  username 7 privilege 15 password badger badger
  iomem 15 memory size
  IP subnet zero
  !
  !
  no ip domain-lookup
  IP - test.local domain name
  !
  property intellectual ssh delay 30
  property intellectual ssh authentication-2 retries
  !
  crypto ISAKMP policy 5
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key VPN2VPN address 83.1.16.1
  !
  86400 seconds, duration of life crypto ipsec security association
  !
  Crypto ipsec transform-set esp - esp-md5-hmac VPN
  !
  crypto map 5 VPN ipsec-isakmp
  defined by peer 83.1.16.1
  PFS group2 Set
  match address VPN
  !
  call the rsvp-sync
  !
  interface Loopback10
  20.0.2.2 the IP 255.255.255.255
  !
  interface Tunnel0
  bandwidth 1544000
  20.0.0.1 IP address 255.255.255.0
  source of Loopback10 tunnel
  tunnel destination 20.0.2.1
  !
  interface FastEthernet0/0
  Description * inside the LAN CONNECTION *.
  address 192.168.20.1 255.255.255.0
  IP nat inside
  automatic duplex
  automatic speed
  !
  interface Serial0/0
  Description * INTERNET ACCESS *.
  IP 88.12.45.1 255.255.255.252
  NAT outside IP
  VPN crypto card
  !
  interface FastEthernet0/1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  Router eigrp 1
  network 20.0.0.0
  No Auto-resume
  !
  overload of IP nat inside source list NAT interface Serial0/0
  IP classless
  IP route 0.0.0.0 0.0.0.0 Serial0/0
  no ip address of the http server
  !
  !
  NAT extended IP access list
  deny ip 192.168.20.0 0.0.0.255 192.168.200.0 0.0.0.255
  deny ip 192.168.20.0 0.0.0.255 192.168.300.0 0.0.0.255
  deny ip 192.168.20.0 0.0.0.255 192.168.100.0 0.0.0.255
  ip licensing 192.168.20.0 0.0.0.255 any
  list of IP - VPN access scope
  permit ip host 20.0.2.2 20.0.2.1
  !

  Config PIX

  ====================

  PIX Version 7.2 (4)
  !
  pixfirewall hostname
  names of
  name 20.0.2.2 B_LOOP
  name 88.12.45.1 B_WANIP
  !
  interface Ethernet0
  Description * LINK to ISP *.
  nameif outside
  security-level 0
  IP 83.1.16.1 255.255.255.252
  !
  interface Ethernet1
  Description * LINK TO LAN *.
  nameif inside
  security-level 100
  IP 192.168.50.1 255.255.255.252
  !
  passive FTP mode
  the ROUTER_LOOPS object-group network
  network-object 20.0.2.0 255.255.255.252
  access allowed extended VPN ip host 20.0.2.1 B_LOOP list
  access-list extended SHEEP permit ip host 20.0.2.1 ROUTER_LOOPS object-group
  Access ip allowed any one extended list ACL_OUT
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global (1 interface external)
  NAT (inside) 0 access-list SHEEP
  NAT (inside) 1 192.168.50.0 255.255.255.252
  NAT (inside) 1 192.168.50.0 255.255.255.0
  Access to the interface inside group ACL_OUT
  Route outside 0.0.0.0 0.0.0.0 83.1.16.2 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp - esp-md5-hmac VPN
  86400 seconds, duration of life crypto ipsec security association
  VPN 5 crypto card matches the VPN address
  card crypto VPN 5 set pfs
  card crypto VPN 5 set peer B_WANIP
  VPN 5 value transform-set VPN crypto card
  card crypto VPN 5 defined security-association life seconds 28800
  card crypto VPN outside interface
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 5
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  tunnel-group 88.12.45.1 type ipsec-l2l
  IPSec-attributes tunnel-group 88.12.45.1
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !

  When you create a GRE tunnel between two routers, there should be a routing decision to reach the Remote LAN through local (rather than exit directly the physical interface) tunnel interface.

  This could be accomplished by EIGRP, but you can check if the adjacency is built.

  As a test, what happens if you add a static route saying (reach remote LAN, sending traffic to the tunnel interface).

  Check if the GRE tunnel comes up with sh interface tunnel

  Federico.

• PIX 501 and VPN Linksys router (WRV200)

  I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other

  sites. Asked me to connect these routers Linksys firewall PIX via the VPN.

  According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.

  Key exchange method: Auto (IKE)

  Encryption: Auto, 3DES, AES128, AES192, AES256

  Authentication: MD5

  Pre Shared Key: xxx

  PFS: Enabled

  Life ISAKMP key: 28800

  Life of key IPSec: 3600

  The pix, I installed MDP and I tried to use the VPN wizard without result.

  I chose the following settings when you make the VPN Wizard:

  Type of VPN: remote VPN access

  Interface: outside

  Type of Client VPN device used: Cisco VPN Client

  (can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)

  VPN clients group

  Name of Group: RabyEstates

  Pre Shared Key: rabytest

  Scope of the Client authentication: disabled

  Address pool

  Name of the cluster: VPN - LAN

  Starter course: 192.168.2.200

  End of row: 192.168.2.250

  Domain DNS/WINS/by default: no

  IKE policy

  Encryption: 3DES

  Authentication: MD5

  Diffie-Hellman group: Group 2 (1024 bits)

  Transform set

  Encryption: 3DES

  Authentication: MD5

  I have attached the log of the VPN Linksys router VPN.

  This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.

  Thanks for your help!

  Hello

  Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.

  Let me know.

  See you soon,.

  Daniel

• The VPN client VPN connection behind other PIX PIX

  I have the following problem:

  I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

  So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

  I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

  Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

  If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

  305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

  194.x.x.x is our customer s address IP PIX

  I understand that somewhere access list is missing, but I can not understand.

  Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

  Can you please help me?

  Thank you in advan

  The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

  I've cut and pasted here for you to read, I think that the problem mentioned below:

  Question:

  Hi Glenn,.

  Following is possible?

  I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

  The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

  My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

  Thank you very much for any help provided in advance.

  Response from Glenn:

  First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

  fixup protocol esp-ike

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

  If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

  ISAKMP nat-traversal

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

  NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

  ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

  A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

  NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

  Hope that helps.

• VPN does not work with the ip address of overlap?

  When I plugged my adsl router and I have ip address is 10.1.1.1/8 can I use remote access vpn closing on firewall and authentication works very well and I put the ip address of the pool is 10.7.0.1/16 but I can not access this local lan if I made up of my pc and got 2x2.102.x.y ip address then I connected I can't access no problem local network and vpn remote access authentication.

  It is question of routing on pc with overlapping ip or not?

  Please clarify or provide useful link

  Thank you

  Hello

  It seems that it is a problem of nat - t.

  Make sure that the head of VPN network has "isakmp nat - t" (if that's a PIX). If a hub, make sure that "IPsec NAt - T" is enabled.

  Additionally, make sure that on the client, "Enable Transparent tunneling" is checked, with IPSec over UDP NAT/PAT selected.

  HTH,

  -Kanishka

• The local PIX ip access to hosts on the VPN site

  I have a vpn connection from site to site with ASA 5510 PIX 515 which works very well. There is no problem for hosts on any side of the tunnel access to a cross. However the IP local (192.168.20.1) on the interface client of my PIX is not allowed access to guests across the tunnel.

  Packet-trace entry client tcp 192.168.20.1 12345 192.168.13.13 80 detailed

  Phase: 3

  Type: ACCESS-LIST

  Subtype:

  Result: DECLINE

  Config:

  Implicit rule

  Additional information:

  Direct flow from returns search rule:

  ID = 0x3ec5bc8, priority = 500, area = allowed, deny = true

  hits = 8, user_data = 0 x 6, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 192.168.20.1, mask is 255.255.255.255, port = 0

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  There must be a setting that I missed. All otherip on 192.168.20.0 don't get the same error with packet - trace. Can someone help me please?

  interface Ethernet0

  nameif outside

  security-level 0

  IP address dhcp setroute

  interface Ethernet1

  customer nameif

  security-level 90

  address 192.168.20.1 255.255.255.0

  interface Ethernet1.21

  VLAN 21

  nameif Server

  security-level 100

  IP 192.168.21.1 255.255.255.0

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.10.0 255.255.255.0

  object-network 192.168.11.0 255.255.255.0

  object-network 192.168.13.0 255.255.255.0

  access-list extended 100 permit customer ip 255.255.255.0 DM_INLINE_NETWORK_1 object-group

  Global 1 interface (outside)

  (Client) NAT 0-list of access 100

  NAT (client) 1 0.0.0.0 0.0.0.0

  NAT (server) 0-access list 100

  NAT (server) 1 0.0.0.0 0.0.0.0

  static (client, server) Server server netmask 255.255.255.0

  static (client, server) client client netmask 255.255.255.0

  client_access_in access to the customer of the interface group

  Route outside 0.0.0.0 0.0.0.0 95.129.13.1 1

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set sveden-aes256 esp-aes-256 esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  correspondence address card crypto myvpnmap 10 100

  card crypto myvpnmap pfs set 10 group5

  peer set card crypto myvpnmap 10 12.218.14.129

  card crypto myvpnmap 10 transform-set sveden-aes256

  life safety association set card crypto myvpnmap 10 28800 seconds

  card crypto myvpnmap 10 set security-association life kilobytes 4608000

  myvpnmap crypto 10 card value reverse-road

  myvpnmap interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  aes-256 encryption

  sha hash

  Group 5

  life 86400

  IPSec-attributes tunnel-group DefaultRAGroup

  ISAKMP retry threshold 10 keepalive 2

  tunnel-group 12.218.14.129 type ipsec-l2l

  tunnel-group 12.218.14.129 General-attributes

  IPSec-attributes tunnel-group 12.218.14.129

  pre-shared-key *.

  Cordially Mikael

  Hello

  You plan to connect to the firewall with address 192.168.20.1 for management purposes or why the IP should be able to generate connections to connect VPN L2L?

  By default, the 'packet - trace' will fail if you are using a firewall interface IP address as the source address of the command. This result is always the same. (Although I have not tried the packet - trace with the below mentioned command enabled)

  If you want to access the IP 192.168.20.1 interface via the L2L VPN on the other side, then you will have to configure

  customer management-access

  Here is more information on the above command

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/m.html#wp2027985

  -Jouni

• PIX 515E (7.0.1) - problem with the VPN connection between inside and outside

  Hello

  I ve creates a VLAN on the pix.

  In this VLAN, users are allowed to connect only to the Internet. Everything is fine, but when trying to connect with his VPN Client to their company, it has problems... (Outside traffic flow, but no traffic came back.)

  Is the only solution for this problem to create a Pool of Nat with public ip addresses, one to one mapping, or is there another solution with a public IP address (NAT on PAT) possible for this problem?

  Thanks for your replies.

  D.

  The problem is that the esp is an IP Protocol, so PAT will not work in this scenario. When the return traffic returns to pix he doesn't know how to get to the inside host. The only way to do this is by adding a static nat (1 to 1 mapping) and create a rule to allow esp. Is what type of vpn client? Microsoft vpn? Cisco vpn? If cisco VPN, perhaps, they can use NAT - T on the vpn that overcomes the question PAT by encapsulating ipsec within UDP packets. You need to talk to the admin VPN and itself it allow.

  -kevin

• Convert the VPN Site-to-Site of PIX to ASA 8.2

  I worked on the conversion of a config above a PIX an ASA 8.2 but I am running into trouble with the site to site vpn. The PIX has a VPN client and site to site. Given that some of the configs for the cross from site to site on the VPN client I'm confuse. Any help would be apperciated.

  Below are excerpts from just the PIX VPN related orders.

  permit access ip 192.168.0.0 list Remote_splitTunnelAcl 255.255.0.0 any

  inside_outbound_nat0_acl ip access list allow any 192.168.0.160 255.255.255.240

  inside_outbound_nat0_acl Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl SilverBack NOC 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl allowed host NOC 255.255.255.0 enoss_Hardware ip access-list

  outside_cryptomap_dyn_20 ip access list allow any 192.168.0.160 255.255.255.240

  outside_cryptomap_20 Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 SilverBack NOC 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 Zenoss_Hardware CNP 255.255.255.0 ip host allowed access list

  IP pool local DHCP_Pool 192.168.0.161 - 192.168.0.174

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  Sysopt connection permit VPN

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set 205.x.29.41

  outside_map crypto 20 card value transform-set ESP-DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  client authentication card crypto outside_map LOCAL

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key address 205.x.29.41 netmask 255.255.255.255 No.-xauth-config-mode no.

  ISAKMP nat-traversal 180

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  part of pre authentication ISAKMP policy 40

  encryption of ISAKMP policy 40

  ISAKMP policy 40 sha hash

  40 2 ISAKMP policy group

  ISAKMP duration strategy of life 40 86400

  vpngroup address pool DHCP_Pool GHA_Remote

  vpngroup dns 192.168.0.11 server GHA_Remote

  vpngroup wins 192.168.0.11 GHA_Remote-Server

  vpngroup GHA_Remote by default-field x.org

  vpngroup split tunnel Remote_splitTunnelAcl GHA_Remote

  vpngroup idle 1800 GHA_Remote-time

  vpngroup password KEY GHA_Remote

  I guess what I really wonder is if someone can convert the version of site to site of this VPN ASA 8.2 config so I can compare it to what I have. I need to have this, so I can just fall into place and work.

  Also, it does appear that political isakmp 40 are used, correct?

  On your ASA in Setup mode, simply type vpnsetup steps for remote access ipsec or vpnsetup site - not and it lists what it takes or you can download the PIX of the ASA migration tool.

• Phone Droid of Pix for the PPTP VPN

  I tried to set up a PPTP VPN between a Droid phone and a performer 6.3.5 Pix code.  As much as I can say the configuration is correct and I can open the vpn pptp fine from my laptop however the Droid refuses to connect.  Here is the relevant configuration.

  VPDN droid group accept dialin pptp

  VPDN group droid ppp authentication pap

  VPDN group droid ppp authentication chap

  VPDN group droid ppp mschap authentication

  VPDN droid Group client configuration address local vpnpool2

  VPDN group droid pptp echo 60

  VPDN group of local authentication client droid

  VPDN group droid username * password *.

  I turned on him debugs following:

  Debug ppp negotiation

  Debug ppp io

  Debug ppp PAPU

  Debug ppp chap

  Debug ppp error

  Debug ppp uauth

  Debug vpdn event

  Debug vpdn error

  VPDN debug package

  I've narrowed the problem down to the following message is displayed, but I'm not sure what this means:

  PPP xmit, ifc = 0, len: 22 data: ff03c021040100120104057802060000000007020802

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: sending xGRE pak to 97.145.147.41, len 38, 18 seq, ack 8, data: 3081880b00169c450000001200000008ff03c021040100120104057802060000000007020802

  Xmit Link Control Protocol pkt, action code is: Config request, len is: 11

  PKT dump: 0305c2238005062affcd96

  LCP option: AUTHENTICATION_TYPES, len: 5, data: c22380

  LCP option: MAGIC_NUMBER, len: 6, data: 2affcd96

  PPP xmit, ifc = 0, len: 19 data: ff03c0210102000f0305c2238005062affcd96

  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: sending xGRE pak to 97.145.147.41, len 35, 19 seq, ack 8, data: 3081880b00139c450000001300000008ff03c0210102000f0305c2238005062affcd96

  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 52799, ack 805406731

  PPP rcvd, ifc = 0, pppdev: 1, len: 28, data: ff03c02101010018010405780206000000000506990009f607020802

  Pkt RCVD Link Control Protocol, action code is: Config request, len is: 20

  PKT dump: 010405780206000000000506990009f607020802

  LCP option: Max_Rcv_Units, len: 4, data: 0578

  LCP option: ASYNC_MAP, len: 6, data: 00000000

  LCP option: MAGIC_NUMBER, len: 6, data: 990009f6

  LCP option: PROTOCOL_HDR_COMPRESSION, len: 2, data:

  LCP option: ADDRESS_CONTROL_COMPRESSION, len: 2, data:

  Xmit Link Control Protocol pkt, action code is: Config Reject, len is: 14

  PKT dump: 0104057802060000000007020802

  LCP option: Max_Rcv_Units, len: 4, data: 0578

  LCP option: ASYNC_MAP, len: 6, data: 00000000

  LCP option: PROTOCOL_HDR_COMPRESSION, len: 2, data:

  LCP option: ADDRESS_CONTROL_COMPRESSION, len: 2, data:

  PPP xmit, ifc = 0, len: 22 data: ff03c021040100120104057802060000000007020802

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 97.145.147.41, len 38, seq 20, sending ack 9, data: 3081880b00169c450000001400000009ff03c021040100120104057802060000000007020802

  PPTP: soc select returns mask rd = 0 x 8

  PPTP: cc rcvdata, socket fd = 3, new_conn: 0

  PPTP: socket closed, fd = 3

  PPTP LNP/Cl/11/11: Session destroy

  Narrow, peripheral PPP going = 1

  PPTP: cc awaiting entry, max soc fd = 2

  If I read that correctly, this is the Pix rejecting the configuration proposed for the Droid phone?

  Any suggestion or help would be greatly appreciated.

  I'm having exactly the same problem.  We receive this reply with debugs on PIX 6.3

  Any help would be appreciated.

  PPTP: socket select return 0 fd

  PPTP: cc awaiting entry, max soc fd = 3

  PPTP: soc select returns mask rd = 0 x 1
  PPTP: new peer fd is 4
  PPTP: created tunnel, id = 23

  PPTP: cc rcvdata, socket fd = 4, new_conn: 1
  PPTP: cc RRs 156 bytes of data

  LNP 23 PPTP: CC I have 009c00011a2b3c4d0001000001000000000000030000000300010000616e6f6e796d6f757300000000000000000000000000000000000000000000000000...
  LNP 23 PPTP: CC I have SCCRQ
  LNP 23 PPTP: version of the Protocol 0 x 100
  LNP 23 PPTP: framing caps 0 x 3
  LNP 23 PPTP: carrier caps 0 x 3
  LNP 23 PPTP: max channels 1
  LNP 23 PPTP: firmware rev 0 x 0
  LNP 23 PPTP: hostname "anonymous."
  LNP 23 PPTP: vendor «»
  LNP 23 PPTP: CC O SCCRP
  PPTP: cc snddata, socket fd = 4, len = 156, data: 009c00011a2b3c4d000200000100010000000003000000030000120057462d50495800000000000000000000000000000000000000000000000000000000...

  PPTP: cc awaiting entry, max soc fd = 4

  PPTP: soc select returns mask rd = 0 x 10

  PPTP: cc rcvdata, socket fd = 4, new_conn: 0
  PPTP: cc RRs 168 bytes of data

  LNP 23 PPTP: CC I have 00a800011a2b3c4d00070000c111175f000003e805f5e1000000000300000003200000000000000000000000000000000000000000000000000000000000...
  LNP 23 PPTP: CC I have OCRQ
  LNP 23 PPTP: call id 0xc111
  LNP 23 PPTP: series num 5983
  LNP 23 PPTP: min bps 1000:0x3e8
  LNP 23 PPTP: max bps 100000000:0x5f5e100
  LNP 23 PPTP: carrier type 3
  LNP 23 PPTP: framing type 3
  LNP 23 PPTP: recv victory size 8192
  LNP 23 PPTP: ppd 0
  LNP 23 PPTP: phone len num 0
  LNP 23 PPTP: phone num «»
  LNP/Cl 23/21 PPTP: CC O OCRP
  PPTP: cc snddata, socket fd = 4, len = 32, data: 002000011a2b3c4d000800000015c1110100000000fa00001000000000000000

  PPTP: cc awaiting entry, max soc fd = 4

  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: sending xGRE pak to 70.199.49.15, len 35, seq 1, ack 0, data: 3081880b0013c1110000000100000000ff03c0210101000f0305c2238005065366bd1e
  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, sending seq 2, ack 0, data: 3081880b0016c1110000000200000000ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, sending seq 3, ack 0, data: 3081880b0013c1110000000300000000ff03c0210101000f0305c2238005065366bd1e
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, sending seq 4, ack 1, data: 3081880b0016c1110000000400000001ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, sending seq 5, ack 1, data: 3081880b0013c1110000000500000001ff03c0210101000f0305c2238005065366bd1e
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, sending seq 6, ack 2, data: 3081880b0016c1110000000600000002ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, sending seq 7, ack 2, data: 3081880b0013c1110000000700000002ff03c0210101000f0305c2238005065366bd1e
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, sending seq 8, ack 3, data: 3081880b0016c1110000000800000003ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, sending seq 9, ack 3, data: 3081880b0013c1110000000900000003ff03c0210101000f0305c2238005065366bd1e
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: sending xGRE pak to 70.199.49.15, len 38, seq 10, ack 4, data: 3081880b0016c1110000000a00000004ff03c021040100120104057802060000000007020802
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: sending xGRE pak to 70.199.49.15, len 35, 11 seq, ack 5, data: 3081880b0013c1110000000b00000005ff03c0210102000f0305c2238005063391d9ff
  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, seq 12, sending ack 5, data: 3081880b0016c1110000000c00000005ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, seq 13, sending ack 5, data: 3081880b0013c1110000000d00000005ff03c0210102000f0305c2238005063391d9ff
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: pak to 70.199.49.15, len 38, seq 14 xGRE sending ack 6, data: 3081880b0016c1110000000e00000006ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, seq 15, sending ack 6, data: 3081880b0013c1110000000f00000006ff03c0210102000f0305c2238005063391d9ff
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: sending xGRE pak to 70.199.49.15, len 38, 16 seq, ack 7, data: 3081880b0016c1110000001000000007ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: xGRE pak to 70.199.49.15, len 35, seq 17, sending ack 7, data: 3081880b0013c1110000001100000007ff03c0210102000f0305c2238005063391d9ff
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: sending xGRE pak to 70.199.49.15, len 38, 18 seq, ack 8, data: 3081880b0016c1110000001200000008ff03c021040100120104057802060000000007020802
  Outdoors - PPTP xGRE interface: Out paket, len PPP 19

  outside PPTP: sending xGRE pak to 70.199.49.15, len 35, 19 seq, ack 8, data: 3081880b0013c1110000001300000008ff03c0210102000f0305c2238005063391d9ff
  outside PPTP: pak xGRE 69.0.0.60 Recvd, len 16366, ack 805406731

  Outdoors - PPTP xGRE interface: Out paket, PPP len 22

  outside PPTP: xGRE pak to 70.199.49.15, len 38, seq 20, sending ack 9, data: 3081880b0016c1110000001400000009ff03c021040100120104057802060000000007020802
  PPTP: soc select returns mask rd = 0 x 10

  PPTP: cc rcvdata, socket fd = 4, new_conn: 0
  PPTP: socket closed, fd = 4

  PPTP: cc awaiting entry, max soc fd = 3

• Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access

  Hello

  I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.

  So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).

  The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)

  I added some ACE for this in the ACL of VPN tunnel to divide.

  NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54

  And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.

  The network INTERIOR, I can connect to the server.

  

  Thanks in advance.

  Hello

  This is most likely a problem with NAT hair/U-turn hairpin.

  Will need to see the configurations or you would need to check yourself

  I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.

  So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.

  Then, you will need to check the output of this command

  See the race same-security-traffic

  You should see the command in the output below

  permit same-security-traffic intra-interface

  If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.

  Then, should ensure that dynamic PAT is configured for the VPN Clients.

  8.2 software (and below)

  You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add

  NAT (outside) 1

  This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server

  Software 8.3 (and above)

  Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a

  network of the VPN-PAT object

  subnet

  dynamic NAT interface (outdoors, outdoor)

  Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.

  Hope this helps

  Let me know how it goes

  -Jouni

• The VPN Clients cannot access any internal address

  Without a doubt need help from an expert on this one...

  Attempting to define a client access on an ASA 5520 VPN that was used only as a

  Firewall so far. The ASA has been recently updated to Version 7.2 (4).

  Problem: Once connected, VPN client cannot access anything whatsoever. Client VPN cannot

  ping any address on internal networks, or even the inside interface of the ASA.

  (I hope) Relevant details:

  (1) the tunnel seems to be upward. Customers are the authenticated by the SAA and

  are able to connect.

  (2) by many other related posts, I ran a ' sh crypto ipsec her "to see the output: it

  appears that the packets are décapsulés and decrypted, but NOT encapsulated or

  encrypted (see the output of "sh crypto ipsec his ' home).

  (3) by the other related posts, we've added commands associated with inversion of NAT (crypto

  ISAKMP nat-traversal 20

  crypto ISAKMP ipsec-over-port tcp 10000). These were in fact absent from our

  Configuration.

  (4) we tried encapsulation TCP and UDP encapsulation with experimental client

  profiles: same result in both cases.

  (5) if I (attempt) ping to an internal IP address of the connected customer, the

  real-time log entries ASA show the installation and dismantling of the ICMP requests to the

  the inner target customer.

  (6) the capture of packets to the internal address (one that we try to do a ping of the)

  VPN client) shows that the ICMP request has been received and answered. (See attachment

  shooting).

  (7) our goal is to create about 10 VPN client of different profiles, each with

  different combinations of access to the internal VLAN or DMZ VLAN. We do not have

  preferences for the type of encryption or method, as long as it is safe and it works: that

  said, do not hesitate to recommend a different approach altogether.

  We have tried everything we can think of, so any help or advice would be greatly

  Sanitized the ASA configuration is also attached.

  appreciated!

  Thank you!

  It should be the last step :)

  on 6509

  IP route 172.16.100.0 255.255.255.0 172.16.20.2

  and ASA

  no road inside 172.16.40.0 255.255.255.0 172.16.20.2

• SSL VPN IP address other than the IP address of the interface?

  Hi,
  
  Is it possibe to use a differnt IP Address from the same Subnet of OUTSIDE
  
  INTERFACE? Instead of Interface IP Address itself. The Idea behind is,
  
  Clients should not use OUTSIDE Interface IP Address for SSL VPN, but whereas they can
  
  use from the IP Address Pool of OUTSIDE Interface.
  Regards

  Brassart Abbas

  If SSL is completed on an ASA firewall, you can finish it on all other ip addresses but the external interface.

  If it is completed on a router IOS, Yes, you can use a different ip address to put an end to the SSL VPN connection.

  Hope that answers your question.

• 2 VPN tunnels on ASA common; A PRI a BKP at the same address-end peer

  Hi all

  I have an ASA 5505 branch that has 2 circuits ISP.  I have a data center ASA who has 1 ISP circuit. I have a VPN tunnel between the primary circuit ASA branch and the ASA circuit data center.  I would like to implement the ASA branch for the redundancy of the SLA so I can use primary and backup circuits, but two configs tunnel going to the same address-end peer, since the data center has only 1 ASA. I read that an ASA cannot have several tunnels to the same peer address because the ASA may have 1 SA by peer address.

  However, if I have my branch ASA configured for redundancy of the SLA, then only 1 tunnel would at once, which I think would affect the requirement of SA above.

  Can someone tell me if this is possible?

  Thank you.

  Hi Dean,

  You're right about things als because only link will be active at a time.

  On the ASA branch, you can apply the same encryption card to two primary and secondary circuit. You use just ALS to determine how this ASA branch will reach the address of peer card crypto (IP addr of ASA Data Center).

  I wrote an article about a similar scenario here: http://resources.intenseschool.com/using-vpn-tunnels-as-backup-links-primary-and-backup-vpn-tunnels-on-cisco-asa/

• Journal entries of false IP addresses in the VPN session

  I noticed a very strange problem on ASA5520 running version 9.1 (1). Whenever a VPN user disconnects (or expires or gets disconnected with force), a journal entry refers to the IP address that is not the user's IP address. It is one of the examples where the 196.95.116.118 IP address is logged:

  -SNIP-

  March 28, 2014 13:37:45: % ASA-4-113019: group = , username = , IP = 196.95.116.118, disconnected Session. Session type: IKEv1, duration: 0: 00: 05:00, xmt bytes: 59216, RRs bytes: 123329, reason: the user has requested

  -SNIP-

  So far, I have captured about 7 of these IP addresses and they all model x.x.116.118. This is the list:

  24.80.116.118
  60.57.116.118
  84.104.116.118
  164.78.116.118
  180.18.116.118
  196.95.116.118
  202.89.116.118

  None of them are related to any of my clients or the company itself. In addition, they do not belong to my ISP. In all of the features VPN and ASA are not affected. Anyone who would have knowledge or idea where these addresses are known to and why they have this strange pattern?

  Hello

  This related to a bug https://tools.cisco.com/bugsearch/bug/CSCub72545/?reffering_site=dumpcr

  It will be useful.

  Kind regards

  Shetty

• How to check if the address pool is used by the vpn client

  Hello world

  I need config anyconnect VPN on ASA existing who also owns the remote VPN client running.

  Under the ASDM when I click the address pools

  I see two address pools

  Pooldefault that I can see is used by vpn distance courses.

  PoolX - this subnet is not assigned to the user now.

  Is there a way I can check if PoolX subnet is configured to assign the IP address to the remote VPN?

  Concerning

  MAhesh

  Hello

  On the CLI, you could check the output of

  See establishing group policy enforcement

  and

  See the tunnel-group race

  to see if the PoolX is used nowhere in the VPN configurations.

  Of course, you can also just simply look for the configuration and see if there is anything else than the current configuration of the PoolX on the SAA.

  See the race | PoolX Inc.

  This should probably display only the command "ip local pool ' if the address pool has just been created but is not used anywhere.

  -Jouni