Phone Droid of Pix for the PPTP VPN

Similar Questions

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• Is it still possible? Customer VPN traffic through a PIX for an another VPN?

  Hi, I just want to know if the following is actually technically possible? I'm starting to think I'm trying to implement a solution that is simply not possible.

  I have the following:

  VPN<->CiscoPix506e<->Cisco3000 Clients

  VPN clients running an IPSEC VPN for the 506th Cisco PIX and can access its "internal network" very well.

  The Cisco pix is running a VPN to another company where all network traffic is nat'ed to a single address IP RFC1918 before coming out of the tunnel (requirement of the other company to avoid the problems of overlap)

  and everyone on the "internal network" can access this great VPN.

  I want that people who use the VPN client to be able to access the other site-to-site VPN. I think that NAT forced to the external company VPN is a problem.

  All of the examples for VPN VPN cross-I see specify NAT should be disabled on the entire path. I can't do it in this situation. Is it possible to make this work?

  I guess with a good statement of ACL that all my problems will be solved.

  If you just get the users connect to the cisco 3000 rather than transversing my network. I don't have for the following reasons. I have no access to the cisco 3000 vpn concentrator and a very limited amount of the tunnels that they can open for my business. I was instructed to implement a solution to facilitate the life of employees (so that they only run a VPN tunnel at a time to do their work). For the moment, they need access to the systems within our corporate network and external society through the site to site VPN (it's actually a web application). They can do this at the office but obviously not home if they attempt to use remote access.

  I have attached a diagram of the network example PDF explaining the situation.

  Networks of each address is the following (change of the actual address of the innocents :))):

  CLIENTS_VPN

  192.168.10.0/24

  Internal network

  192.168.1.0/24

  External VPN end point

  192.168.20.0/24

  Address used for NAT on the VPN

  172.16.1.1/32

  the IOS config

  local IP pool - 192.168.10.1 VPN CLIENTS - 192.168.10.254

  inside ip access list allow a whole

  access-list allowed SHEEP ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0

  access list permits EXTERNAL-ACL-VPN ip 172.16.1.1 host 192.168.20.0 255.255.255.0

  EXTERNAL-ACL-NAT of the list of permitted access ip 192.168.1.0 255.255.255.0 192.168.20.0 255.255.255.0

  IP address outside a.b.c.d 255.255.255.0

  IP address inside 192.168.10.1 255.255.255.0

  Global interface 2 (external)

  Global (outside) 1 172.16.1.1

  NAT (inside) 0 access-list SHEEP

  NAT (inside) - EXTERNAL-ACL-1 NAT access list 0 0

  NAT (inside) 2 0.0.0.0 0.0.0.0 0 0

  outside access-group in external interface

  Route outside 0.0.0.0 0.0.0.0 a.b.c.d 1

  Thank you

  Jason.

  I understand from your description of the scenario, you try to route traffic on the same interface on which it was received on the PIX. This is called pinning hair in traffic and is not currently supported in PIX (6.3).

• Function of automatic update for the IPsec VPN Client

  Hello.

  Do you have anyone ever tried the PIX / ASA ' feature IPsec VPN Client Auto-Update?

  (see also Document ID: 105606).

  He wants to make sure that I understand this right.

  The user will receive a popup of information telling him to download the latest version of the client? And then there start the update itself?

  If so, this would mean that the user must have the rights of full adminsitative using a laptop.

  From my point of view, full administrator rights on a laptop are prohibited - 100% and therefore the functionality would be totally useless.

  Anyone who can tell me whether I am good or bad?

  Best

  Frank

  Frank,

  You are right, if the computer desktop or labtop is completely locked regarding the installation of the software the customer won't be able to install it, they may be able to download from the link that you configured in ASA, once they connect to your server ASA RA but with regard to the installation user's machine needs rights profile appropriate to be able to install it.

  HTH

  -Jorge

• which product is right for the ssl vpn: asa 5505 cisco 1841 or

  Hello

  I want to install an outside link management related so that we can ssh to our cisco devices and microsoft RDP toour servers. It's my configuration (based on what I know):

  Internet > DSL modem > ASA 5505 > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

  or

  Internet > 1841 with DSL HWIC > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

  My questions are:

  Should I go for ASA or 1841 router?

  What options is better? and ASA will do the job?

  Are there any technical support prior to purchase of products in Australia? I need technical advice on the choice of the right products, not justs eiling me products.

  Hello

  Its strongly suggested to go with ASA 5505 in the first place, it is supposed to feature for the main functionality of ssl vpn server from 1841 which has this feature to be a vpn server.

  ASDM also gives you the freedom to config box on your own based on your condition.

  regds

• Help with customer 501 pix for the configuration of a site...

  Hello everyone, I am trying to set up a customer vpn site and after a few days

  I'm at the end of the roll.

  I'd appreciate ANY help or trick here.

  I tried to set up the config via CLI and PDM, all to nothing does not.

  Although the VPN client log shows the invalid password, I am convinced that the groupname password is correct.

  I use the Cisco VPN Client 5.0.07.0290 v.

  -----------------------------------------------------------------

  Here is HS worm of the PIX:

  Cisco PIX Firewall Version 6.3 (5)
  Cisco PIX Device Manager Version 3.0 (4)

  -----------------------------------------------------------------

  Here's my sh run w / passwords removed:

  pixfirewall # sh run
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 10baset
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password to something
  that something encrypted passwd
  pixfirewall hostname
  domain ciscopix.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list ping_acl allow icmp a whole
  permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168
  . 50.48 255.255.255.248
  outside_cryptomap_dyn_20 ip access list allow any 192.168.50.48 255.255.255.248

  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside pppoe setroute
  IP address inside 192.168.1.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool vpnpool 192.168.50.50 - 192.168.50.55
  history of PDM activate
  ARP timeout 14400
  Global interface 10 (external)
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
  Access-group ping_acl in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value
  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
  outside_map interface card crypto outside
  ISAKMP allows outside
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  vpngroup address vpnpool pool vpnaccessgroup
  vpngroup dns 192.168.1.1 Server vpnaccessgroup 192.168.1.11
  vpngroup wins 192.168.1.1 vpnaccessgroup-Server
  vpngroup vpnaccessgroup by default-field local.com
  vpngroup idle 1800 vpnaccessgroup-time
  something vpnaccessgroup vpngroup password
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 60
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  VPDN group pppoe_group request dialout pppoe
  VPDN group pppoe_group localname someone
  VPDN group ppp authentication pap pppoe_group
  VPDN username someone something
  dhcpd address 192.168.1.100 - 192.168.1.110 inside
  dhcpd dns 206.248.154.22 206.248.154.170
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:307fab2d0e3c5a82cebf9c76b9d7952a
  : end

  -----------------------------------------------------------------------------------------------

  Here is the log of pix in trying to connect with the client vpn cisco w / real IPs removed:

  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco PIX IP here] spt:64897 TPD:
  500
  Exchange OAK_AG
  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 2 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 3 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 4 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 5 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 6
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 7
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 8 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 9 against priority policy 20
  ISAKMP: 3DES-CBC encryption
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP (0): atts are not acceptable.
  crypto_isakmp_process_block:src:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  pixfirewall #.

  ---------------------------------------------------------------------------------------------------------------

  Here is the log of the vpn client:

  363 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100002
  Start the login process

  364 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100004
  Establish a secure connection

  365 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100024
  Attempt to connect with the server '[cisco pix IP here]. "

  366 16:07:58.953 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  From IKE Phase 1 negotiation

  367 16:07:58.969 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) [cisco pix IP here]

  368 16:07:59.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700008
  IPSec driver started successfully

  369 07/01/10 Sev 16:07:59.078 = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  370 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000014
  RECEIVING< isakmp="" oak="" ag="" (sa,="" vid(xauth),="" vid(dpd),="" vid(unity),="" vid(?),="" ke,="" id,="" non,="" hash)="" from="" [cisco="" pix="" ip="">

  371 16:08:00.110 01/07/10 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified

  372 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.

  373 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 915)

  374 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) [cisco pix IP here]

  375 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: AUTH_FAILED) [cisco pix IP here]

  376 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE30000A7
  SW unexpected error during the processing of negotiator aggressive Mode:(Navigator:2263)

  377 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000017
  Marking of IKE SA delete (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  378 16:08:01.078 01/07/10 Sev = Info/4 IKE/0x6300004B
  IKE negotiation to throw HIS (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  379 16:08:01.078 01/07/10 Sev = Info/4 CM / 0 x 63100014
  Could not establish the Phase 1 SA with the server "[cisco pix IP here]" due to the "DEL_REASON_IKE_NEG_FAILED".

  380 16:08:01.078 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  Signal received IKE to complete the VPN connection

  381 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  382 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  383 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  384 16:08:01.078 01/07/10 Sev = Info/4 IPSEC/0x6370000A
  IPSec driver successfully stopped

  Mmmm... What version of vpn client do you use?

  If you use the last being, it looks like you might have it downgrade to a version older than the version of your PIX is old enough.

• IPSec sequence numbers not working not for the multi VPN

  a site at a single site VPN works no problem, but when I add the second peer in the concentrator, router it does not connect. There is no routing in place that all routers are connected to the same switch, and with no crypto card they can all two ping 192.168.2.1. With crypto card only 192.168.2.2 can ping 192.168.2.1. I'm at a loss as to what I'm doing wrong, it seems simple I just add the Test input with a different number, but it won't work.

  Ask any other question you can think of. I followed the same controls on both spoke routers so that it seems that it would be in the hub, router, but he beat me as to why.

  Thanks for the help.

  Concentrator, router:

  ----------------------------------------------------------------------------------------------------------------------------------------------

  R1 #sh card crypto

  1 test card crypto ipsec-isakmp

  Peer = 192.168.2.2

  Expand the IP 110 access list

  access ip-list 110 permit a whole

  Current counterpart: 192.168.2.2

  Life safety association: 4608000 kilobytes / 86400 seconds

  PFS (Y/N): N

  Transform sets = {}

  Test,

  }

  Interfaces using crypto sheet test:

  FastEthernet0/0

  2 ipsec-isakmp crypto map test

  Peer = 192.168.2.3

  Expand the IP 110 access list

  access ip-list 110 permit a whole

  Current counterpart: 192.168.2.3

  Life safety association: 4608000 kilobytes / 86400 seconds

  PFS (Y/N): N

  Transform sets = {}

  Test,

  }

  Interfaces using crypto sheet test:

  FastEthernet0/0

  ---------------------------------------------------------------------------------------------------------------------------------------------

  R2 #sh card crypto

  1 test card crypto ipsec-isakmp

  Peer = 192.168.2.1

  Expand the IP 110 access list

  access ip-list 110 permit a whole

  Current counterpart: 192.168.2.1

  Life safety association: 4608000 kilobytes / 86400 seconds

  PFS (Y/N): N

  Transform sets = {}

  Test,

  }

  Interfaces using crypto sheet test:

  FastEthernet0/0

  ----------------------------------------------------------------------------------------------------------------------------------------------

  R3 #sh card crypto

  1 test card crypto ipsec-isakmp

  Peer = 192.168.2.1

  Expand the IP 110 access list

  access ip-list 110 permit a whole

  Current counterpart: 192.168.2.1

  Life safety association: 4608000 kilobytes / 86400 seconds

  PFS (Y/N): N

  Transform sets = {}

  Test,

  }

  Interfaces using crypto sheet test:

  FastEthernet0/0

  There is a typing error in the IP for the PSK on R3.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Control the access of the user for the SSL VPN profile.

  I have two ssl vpn profile, can I restricted the user to access only ssl vpn profile, when they get to the page of the ssl vpn service. Each profile to create different types of access, and they will have different client IP address.

  Hello

  Yes, using different ways; one of them is using group-lock, which is a simple check to validate if the Tunnel group or the connection profile as you called it with that sign corresponds to what you have defined under group policy. If the value of Tunnel-Group-Lock (condition true), the VPN remote access session is allowed to install;  otherwise the session is not allowed to be implemented.

  The tunnel-group-lock featurecan be defined as follows:

  • via the group-policy setting locally on ASA
  • via the LDAP attribute
  • via the Radius attribute

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa82/configuration/guide/vpngrp.html#wp1134870

  Step 4

  Kind regards

• Need phone support from microsoft for the Greece

  Original title: hotline

  Hello I need phone support from microsoft for greece.can anyone help me?

  Phone numbers for global customer support

• Router configuration Cisco for the IPSec VPN with VPN in Windows 7 builtin client

  Where can I find an example config for IPSec VPN where Windows 7 native client to connect to the Cisco routers. I use the cisco 881w, in this case.

  Thomas McLeod

  Native Client Windows supports only L2TP over IPSec. Example at the end of this doc may be enough for you:

  http://www.Cisco.com/en/us/docs/security/vpn_modules/6342/configuration/guide/6342vpn4.html#wp1036111

  I've not personally configured L2TP/IPSec on IOS, only on ASA, so cannot be 100% sure that the config in the link works, but the general idea should be ok.

• PPTP VPN or IPSEC for Android and iPAD

  Being new on the RV180 (and routers VPN besides) I had trouble getting a VPN's, supporting my iPad and Android devices. However, I understand that an IPSEC connection would be a safer sollution. Unfortunately I can't find a clear statement anywhere to do it.

  I found descriptions/parameters in the different RV180 of the setting of the (few) in mobile platforms. So far not managed to get the installation program.

  Little help to start would be great!

  Thank you very much.

  Ronald

  Hello Robert.

  My name is Chris and I work at the Cisco Small Business Support Center.

  The PPTP option will be much easier to install, and most devices have a built-in capability of PPTP.

  The RV180 supports the IPSEC tunnels, but only for links from site to site or a remote user with the client software.  Some of the other features of our support SSL VPN connections, which would allow you to use the Cisco Anyconnect client available for android, but SSL VPN is not a characteristic of the RV180.

  On my Android (Droid X running Android 2.3.4) phone he built in VPN, IPSEC and PPTP client.  Yours is probably as well, but if not there should be a few apps available.

  If you decide to go with PPTP you can configure it like this on the RV180:

  1. go to the router admin page and click on VPN > IPsec > VPN users.

  2. check the box to enable the PPTP server.

  3. complete the range of internal addresses for your customers to use PPTP (192.168.1.200 - 192.168.1.210 for example)

  4. click on save.

  5. Once you click on save, you should be able to edit the table of parameters of VPN client.

  6. click on add, check enabled, enter a user name and password for the PPTP user to use and for the protocol type, select PPTP.

  7. click Save to add the user.

  Once this is done, you should be able to go into the settings on your Android device and add a VPN for PPTP connection.   Fill in the same information you setup of the RV180 and you should be able to connect.

  The server address will be the WAN IP of your RV180.

  As far as IPSEC goes, the process is similar but a little more complicated.

  1. on the router admin page go to VPN > IPsec > Basic VPN configuration.

  2. choose the VPN client for peer type.

  3. name connection (it is used on the router)

  4. choose a pre-shared key to be used with this connection.

  5. for remote WAN IP address, you can leave the default remote.com

  6. for the Local gateway Type, you'll want to choose IP

  7. to Local WAN IP select IP and enter the IP address of the RV180 (WAN IP)

  8. for LAN Local, enter the local network for the RV180 ID (default is 192.168.1.0)

  9. to the Local LAN subnet mask enter 255.255.255.0

  10. click on save.

  The steps above create a VPN IPSec tunnel using the default values of the router, which you can view by clicking on default settings under VPN > IPSEC.

  Now you just set your phone.  On my phone, I have an option for Advanced IPSEC VPN, but yours may be different, or you may need to use an application like a customer, if your phone does not have built-in IPSEC VPN.

  On my Droid X, I want to go wireless and networks, VPN settings, Advanced IPSEC VPN, add a new virtual private network.

  My phone uses models of connection, so be sure to choose one that fits your tunnel on the RV180 parameters.

  Enter the RV180 WAN IP address as the VPN server, as well as the pre-shared key, install you on the RV180.

  Make sure that all connection settings that you have configured on the RV180.

  You will also be asked for an internal subnet IP address, and for this, you must enter the Local LAN and subnet mask, that you configured on the RV180 in steps 8 and 9 above.

  I wish I could be more specific, but it seems that there are several different menus and options depending on what Android phone using your.

  I hope that this helps, but if not feel free to respond and I'll try to explain.

• divide the tunnel pptp vpn router 7200

  I have cisco 7200 running Cisco IOS Software, software 7200 (C7200-ADVENTERPRISEK9-M), Version 12.4 (24) T2, VERSION of the SOFTWARE (fc2). I want that connects to the pptp VPN in order to access the internet at the same time. I think that this can be achieved by implementing split VPN tunnel. However I can't understand how to implement this on my 7200. All the documentation I found only tell how to do it on a cisco ASA. I've been watching this article to help me to http://www.cisco.com/en/US/tech/tk59/technologies_configuration_example09186a00800a393b.shtml#con4VPN clients will assign an ip address in the range of 172.16.10.0/24 to access the network remote fo 17.16.0.0/24Looking to the article posted above, I created the list 102 permit ip 172.16.0.0 ACLaccess 0.0.0.255 172.16.10.0 is 0.0.0.255What I can not understand how to apply this to my activation of VPDN PPTP groupvpdn
  !
  VPDN-Group 1
  !  PPTP by default VPDN group
  accept-dialin
  Pptp Protocol
  virtual-model 1
  ! interface virtual-Template1
  IP unnumbered GigabitEthernet0/2
  peer default ip address pool-pptp pool
  PPP encryption mppe auto
  PPP ms-chap for authentication ms-chap-v2
  ! access-list 102 permit ip 172.16.0.0 0.0.0.255 172.16.10.0 0.0.0.255
  Local IP pool pptp 172.16.10.1 172.16.10.254Any help is appreciatedThanks

  Split PPTP tunnel must be configured on the client. Unlike the IPSec tunnel split which is performed on the head end, split PPTP tunnel is configured on the client itself.

  Here is the configuration guide for document Q & A (last question):

  http://www.Cisco.com/en/us/Partner/Tech/tk827/tk369/technologies_q_and_a_item09186a00800946ef.shtml

  Here is an article from Microsoft that takes in charge who:

  http://TechNet.Microsoft.com/en-us/library/cc779919%28WS.10%29.aspx#w2k3tr_vpn_how_dkma

  Hope that helps.

• Using configuration for the 2nd link of lan to lan vpn

  Hello

  Successfully, I configured a connection of lan to lan vpn between two offices. I try to add another link to a 3rd office to my office at home, but have some difficulty. I have attached my setup and hope someone can help me solve my problem. Right now I have a working vpn to the 172.16.0.0/24 network and putting in place the link to 172.16.3.0/24 so. For the new vpn connection, I can ping the external interfaces, but can't ping anything in-house.

  Thanks for your time and help,

  Jason

  Jason

  There is a major mistake that's easy to fix. You have successfully created a second instance of the encryption card to create a VPN tunnel for the second site. But as currently configured two instances of the encryption card use the same access list:

  1 ipsec-isakmp crypto map clientmap

  match address 100

  5 ipsec-isakmp crypto map clientmap

  match address 100

  But each session/tunnel VPN needs its own access list. So, I suggest that you make the following changes:

  5 ipsec-isakmp crypto map clientmap

  match address 101

  no access list 100

  access-list 100 permit ip 192.168.0.0 0.0.0.255 172.16.0.0 0.0.0.255

  access-list 101 permit ip 192.168.0.0 0.0.0.255 172.16.3.0 0.0.0.255

  This provides a list of separate for each session/tunnel access and should solve this problem. Try it and tell us the result.

  HTH

  Rick

• R7000 PPTP VPN works not

  I have a windows VPN (PPTP) Server behimd my Nighthawk R7000 router but the router does not allow for VPN passthrough? Any ideas?

  I have port 47 GRE TCP/UDP and TCP 1723/UDP sent to my IP address of the VPN server. Am I missing something? It be a checkbox to enable VPN passthrough but I don't see on the R7000 nighthawk? Its not me to VPN in my network. Help, please. Once again it is for Windows VPN not the customer to Open VPN (that I don't want to use)

  Yes, I have forwarded manually and yes I have chosen pptp vpn in the drop down menu. I managed to solve the problem though! I just removed the pptp vpn service from the drop down and added service pptp again and now everything works fine.

• Downloadable ACLs for users of VPN

  Hello

  I replaced the old pix with ASA (7.2). There were groups configured for the remote VPN users authenticated through the ACS and ACS download a specific ACL for each group to the PIX. After the replacement, users cannot establish the VPN connection. After troubleshooting, I discovered that the downloadable ACLs were not working very well. When I disabled this option the established tunnel. When I get back to the old pix with the same configuration, it works very well with downloadable ACL option. I opened a TAC case and he said the v3.0 ACS (I) are not compatible with the ASA. He did not really convince me and he asked to try to use the option to pair AV. I tried option pair AV with ASA and it did not work also. can you please advice.

  Hello

  Check out this point,

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCef21184

  In addition, 3.0 is very old, and I guess that in this version, we have "Downloadable PIX ACL" and not "downloadable IP ACL", on ASA download able ACL will work but with "Downloadable IP ACL" but not with "Downloadable PIX ACL".

  Kind regards

  Prem