PIX management

Similar Questions

• How Pix manages the rare IP protocol packets

  Does anyone know of a document explaining how the Pix handles, regarding the State, rare IP protocol packages such as ESP, AH, OSPF, GRE, etc. ? I'm concred with traffic flowing through the pix is not intended.

  I understand how TCP, UDP, and ICMP packets are handled, but I can't find anything on all others.

  Thank you.

  In General, the Pix must inspect any protocol passes through it accepts for TCP and UDP. The exception is a protocol which is managed by a '' correction '' like PPTP which has a correction to allow GRE (Protocol 47) traffic that results.

  If you want a different protocol than UDP/TCP to be allowed to get THROUGH, you almost create an ACL entry for her.

  The other exception is the traffic to the Pix itself as host. ACL have absolutely no effect on the traffic to the Pix as the host. For example, the packets OSPF intended for the Pix when running OSPF. Or packages ESP for the Pix for a VPN tunnel, it stops. Or ICMP traffic to the Pix itself (controlled using the command [icmp]). ACL don't apply to transit traffic.

• port forwarding TCP on pix 501

  can you tell me how to port forward or open tcp 21 and 1024-2774 for the end user of a backup system remotely via the pix Manager or regular here is a copy of my config thanks my apologies if this is a little wave building configuration...

  : Saved

  :

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  list of access allow-permit tcp any any eq www

  access list permits allow tcp everything any https eq

  list of access allow-permit udp any any eq isakmp

  list of access allow-permit udp any any eq field

  list of access allow-permit tcp any any eq telnet

  list of access allow-permit tcp any any eq ftp

  access list permit to allow icmp a whole

  access list allow allow an entire esp

  list of access allow-permit tcp any any eq ssh

  list of access allow-permit tcp any any eq - ica citrix

  list of access allow-permit tcp any any eq pop3

  list of access allow-permit tcp any any eq smtp

  list of access allow-permit tcp any any eq aol

  access list, allow-in allow an entire esp

  access list allow component snap permit udp any any eq isakmp

  access list, allow-in allow icmp a whole

  access list allow component snap permit tcp any any eq ssh

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside x.x.x.226 255.255.255.240

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.1.3 255.255.255.255 inside

  location of PDM 192.168.1.5 255.255.255.255 inside

  location of PDM 192.168.1.6 255.255.255.255 inside

  location of PDM 192.168.1.7 255.255.255.255 inside

  location of PDM 192.168.1.8 255.255.255.255 inside

  location of PDM 192.168.1.9 255.255.255.255 inside

  PDM location x.x.x.88 255.255.255.255 outside

  location of PDM 192.168.1.10 255.255.255.255 inside

  location of PDM 192.168.1.11 255.255.255.255 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static x.x.x.227 (Interior, exterior) 192.168.1.9 netmask

  255.255.255.255 0 0

  public static x.x.x.228 (Interior, exterior) 192.168.1.8 netmask

  255.255.255.255 0 0

  public static x.x.x.229 (Interior, exterior) 192.168.1.3 netmask

  255.255.255.255 0 0

  public static x.x.x.230 (Interior, exterior) 192.168.1.5 mask

  255.255.255.255 0 0

  public static x.x.x.231 (Interior, exterior) 192.168.1.7 netmask

  255.255.255.255 0 0

  public static x.x.x.232 (Interior, exterior) 192.168.1.6 netmask

  255.255.255.255 0 0

  Access - allows to group in the interface outside

  allow-out access-group in the interface inside

  Route outside 0.0.0.0 0.0.0.0 216.215.244.225 1

  Timeout xlate 0:05:00

  Timeout conn 0 half-closed 01:00:10: 00 udp 0: CPP 02:00 0:10:00 h323

  0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd dns 64.89.70.2 64.89.74.2

  dhcpd lease 2000000

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  [OK]

  Hello

  Port forwarding is different to allow ports through the firewall. I guess you meant allow tcp/21 and 21 1024-2774, right port?

  You need the following lines

  access list allow component snap permit tcp any any eq ftp

  access list allow component snap allowed tcp everything any 1024 2774 Beach

  You can be more specific and can replace "any" with the actual IP addresses

  Thank you

  Nadeem

• Port 1476 (registered csdmbase port) opened in Interface PIX 515

  Ive scanned my interface internal pix and Ive found this port (TCP 1476)

  Open. Ive not found CISCO documentation on this topic.

  who knows?

  If you are looking for ORC for: pix port 1476

  you will find that it is used for secure telnet pix. It is the service that is used for CSPM (pix management software) to communicate securely with the pix.

  HTH

  The f

• Best approach and Apps to manage Pix taken on the iPhone and sync.

  Can someone direct me to articles or the spirit to give me a quick post re: a great way to manage my pix that I take on my iPhone 6 then organize into folders easily and have the synchronization of files to my other mobile devices and Apple computers? My iPad and iPhone are both on the same iOS but my computers are a little different: I always use Lion (10.7.5) on my Mac Pro and Yosemite (10.10.5) on my Macbook Pro. My equipment is:

  1. iPhone 6 (iOS 9.3.2)
  2. Air iPad (iOS 9.3.2)
  3. MacBook Pro (OSX Yosemite 10.10.5)
  4. Mac Pro (OSX Lion 10.7.5)

  Basically, I want to be able to create a folder of say on my iPhone and put relevant pix in it and have the folder synchronization and pix of my devices above. And if I were to edit or delete a photo on another device synchronization of changes to the other 3 devices. Key word is easily. The best analogy I just with that is IMAP for email, and whose changes are instantaneous and fluid to all other connected devices assuming that you use the same AppleID devices of course.

  Maybe it's me, but I find a bit intuitive Photo Apple application so thinking maybe someone has created a more robust application and intuitive that works on all the other computers and mobile devices Apple.

  I read reviews on App Store and Googling but thought maybe I'd get a stronger recommendation here among the Digerati Apple

  Thank you

  Steven

  the built solution just for this is iCLoud library except for the Lion system - there is no transparent and automatic solution for Lion do what you want

  iCloud Photo library FAQ - Apple Support

  LN

• CAN´t manage the pix of the my next remote site

  Hello

  What should I do or better how can I configure a pix 501 to manage the pix remotely via telnet or pdm?

  can someone give me advice or an example of configuration '

  What I found on the web, has not helped me to.

  Concerning

  Kai

  PIX outside interface does not support telnet. the option is to configure ssh.

  for example

  hostname yourcompanypix

  yourcompany.com.au domain name

  CA generates the key rsa 1024

  CA save all

  SSH outdoors

  to establish an ssh session to the pix outside interface, a ssh client is required as sealant.

  PuTTY is a freeware and can be downloaded from:

  http://www.PuTTY.nl/download.html

• Pix & Editor Photo Manager of LR etc.?

  I spent all my time to test recent editors of different photos - Raw processing, Lightroom, darktable, Capture One, Lightzone, Photoshop Elements, affinity, ACDC Mac Pro, DXO Optics 11 - on and on. Most of them is best editors (IMO) than pictures, but I prefer the ease of use and search for photo management. And since we now have two "extensions" and in particular the extension "External editors", I wonder why I should not simply use pictures for management and my 'catalogue' and some minor/quickie changes and exit to all others, I prefer to do more complex work.

  I mean, what's wrong with this picture? Photos is pretty quick and easy, good import, has a few basic changes, and fantasy guys are always more or less available, either by extensions (or some of them) and by export and re - import (even if it work you on duplicates, I suppose).

  Anyway, would love to hear from someone who has tried this or he tries now, how it worked, and what are the limits, what to watch out for, etc.

  Thank you very much.

  And since we now have two "extensions" and in particular the extension "External editors", I wonder why I should not simply use pictures for management and my 'catalogue' and some minor/quickie changes and exit to all others, I prefer to do more complex work.

  That's what I've done since publishing extensions became available.

  My main reason to stick with Photos is iCloud photo library.  There is no other easy way to sync my library of Photos between multiple Macs.

  I found that I must not fall back on the Photo editing spotted too often. I'm careful to take my pictures so they don't need much editingbeyond straighten the horizon lsightly, cropping, perhaps to correct the white balance and adjust the highlights and shadows. Everything that can be done in pictures.

  I mainly use extensions or external for a correction of perspective editors, if it was not possible to take the picture with the correct perspective, for the smoothing of the skin and for touch-ups. I try to avoid extensions if mounting can be done in Photos, for two reasons:

  • Extensions create a new master file almost, like Aperture. Then they break up which edition.
  • And they are not yet as stable as I could wish. For example, extensions of affinity cannot edit some panoramic shots, they can reframe the edited section. And I often get an error message when I try to save the modified version - for affinity extensions and extensions site, for the most part, if I try to apply multiple extensions to the same photo.

• Do not open the PIX device manager

  After changing the default configuration of the internal ip address can no longer be 3.0 (1) PDM to open in IE 6. I ping the internal IP 192.168.0.1 and pdm does not work with https://192.168.0.1

  Running PIX 501 version 6.3 (3)

  Thank you

  You should do a "show http" and see if you allow hosts on the network 192.168.0.0/24 to PDM in the Pix.

  There is a good chance that this could not been changed from the previous subnet that you were using.

  Hope this helps,

  Peter

• XIA Pixie-4: can I use it with MXI link?

  Dear colleagues!

  Please advice me can use digital Pixie-4 (from manufacturer of XIA) spectrometer with MXI link if I know that there is a special software for LabVIEW 8.5 kit?      This kit has been tested only on 8174 embedded plc and without having tested with MXI link.

  I heard somewhere, if the software package supports LabVIEW 8.5 then MXI link will also work.

  Current 93,

  How works MXI is that he essentially developed bus PCI/PCIe to your PC to allow additional devices working on it. Since it is an instrument of third parties, we cannot make any guarantees about the reliability of their products in some systems. There are some third-party products that can not handle operating systems 64-bit, as well as some computer manufacturers who are unable to manage bridge PCI expansion and this should take into consideration when you decide to use a MXI card in a PXI chassis. However, I believe that as long as your device Pixie-4 of XIA is compatible with the version of Windows and any software on this computer, then it should not cause problems with start-up and operation. Devices may also not appear in measurement and Automation Explorer because they are third-party devices, however, if you have software installed on the PXI-8184 controller, then the same software should work on the desktop PC that uses the MXI map as the same data to which are connected the 8174, is accessible by the MXI Board.

• Win2K NAT would be from 1650 to a PIX 515 - does not

  Hello

  :

  I have a working VPN config on my 515 (6.2.2) and can tunnel from one host with a valid external IP without any problem. But, with a NAT would be customer, nothing seems to work.

  I use RADIUS to authenticate after using a password for the group. Here is the sequence of events.

  (1) client machine as a 10.0.0.1 address, NAT had a public address to come into the port of 'outside '.

  (2) the client connects, the user enters GANYMEDE password and is connected.

  (3) the user tries to browse any service and can not.

  (4) if the user switches DNS to an external server, the portion of the split tunnel internet works fine but inside is still broken.

  (5) clients with static IP addresses that are publicly routable connect and can perform all internal and external activities of split tunnel.

  Excerpts from config. I'm doing something wrong?

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac noaset

  Crypto dynnoamap dynamic-map 10 transform-set noaset

  noamap 10 card crypto ipsec-isakmp dynamic dynnoamap

  Harpy of authentication card crypto client noamap

  noamap interface card crypto outside

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address noapool pool noagroup

  vpngroup dns 66.119.192.1 Server noagroup

  vpngroup noagroup wins server - 66.119.192.4

  vpngroup noagroup by default-field noanet.net

  vpngroup split-tunnel vpn - IP noagroup

  vpngroup idle 3600 noagroup-time

  vpngroup password noagroup *.

  Help and thanks in advance.

  Mike

  You do not have something wrong. The problem is that NAT (NAT actually PAT, port) and IPSec is not working very well, and many features PAT can PAT IPSec traffic to all (PIX included until version 6.3).

  The problem is that PAT depends on using the port number TCP or UDP source as a way to differentiate between sessions, because they are all PAT would be from the same source IP address. However IPSec (ESP at least), tracks right on top of IP, in other words, it is NOT a TCP or UDP protocol, and therefore has no associated port number. It breaks most of the PAT devices.

  The reason for which you can build your tunnel initially, it is that it is all done by ISAKMP, which is a UDP protocol, which can be PAT would be fine. Once the tunnel is built however, all encrypted data are sent by packs of ESP, which as I said, is not a TCP or UDP protocol.

  Trnalsations NAT static work cause they do not rely on the use of the port number, they just change the address of the source that works very well with ESP.

  There is not much you can do about it. If you were closing the VPN into a VPN3000 concentrator, it has a feature called IPSec through NAT, which encapsulates all ESP packets in a UDP packet, which can then be PAT would be properly. The PIX, unfortunately, doesn't have this feature. The only solution is to get a NAT device that manages properly the IPSEc. Surprisingly, some of the less expensive devices on the market handle it, but you should check with each manufacturer to be sure.

• Remote administration of a PIX running as a VPN client

  Hello

  I have a setup where a PIX501 works as a VPN client upward against my central VPN3000 concentrator (LAN-2-LAN with NAT - T mode).

  External interface of the pix is behind a firewall managed by ISP to the remote end, and get it via DHCP IP address.

  So far so good. This configuration works hotel.

  The problem is that I can't ssh/telnet to the external interface of the PIX due to this configuration.

  Would it not possible to ssh/telnet to the remote pix _inside_ interface?

  I guess stuff NAT Bennett, but I can't make it work.

  Any ideas?

  (: O) Mikkle

  This is possible by commands:

  management-access inside

  It works very well as I have used both inside interface is included in all the crypto config

  Sam

• How to configure the PPPoE on PIX 501?

  Mailto: [email protected] / * /

  MSN: [email protected] / * /

  According to the below URL Cisco TAC:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00801055dd.shtml

  but I always failed. And my PIX 501 Configuration noted below:

  pixfirewall # write terminal

  Building configuration...

  : Saved

  :

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxx

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside pppoe setroute

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1

  Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoex request dialout pppoe

  Cisco localname VPDN group pppoex

  VPDN group ppp authentication pap pppoex

  VPDN username xxxx password *.

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  [OK]

  See the pixfirewall version #.

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Thursday 19 March 03 11:49 by Manu

  pixfirewall until 58 mins 6 dry

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 000b.fd58.886b, irq 9

  1: ethernet1: the address is 000b.fd58.886c, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: 50

  Throughput: unlimited

  you have all the debugging logs?

• PIX 515 to Linksys BEFSX41 VPN

  Hello.

  I searched the forums and the best info I could come up with on this topic, this was one person saying "Eureka, I did it!" and then several hundred "Please send me your config" responses.

  I managed to establish a tunnel between the pix and the Linksys router, and I can ping through the tunnel.

  But nothing else ping seems to go through the tunnel. The access-lists on the pix are not limited on the port, and (for testing), I have the great open linksys firewall. So I don't know where I went wrong.

  I was hoping that this could be a common situation and someone could point me in the right direction to find the solution.

  Thank you!

  In addition,

  Check the order of your ACL. A firewall and a router do not ACL in the same order. Should not discourage you, but I have yet to see a router Linksys do very well a PIX. For some reason the Linksys routers seem to drop packets for unexplained reasons...

• Access PIX using SSH when connected remotely with VPN client

  Hello

  I think that this should be a fairly simple for someone to sort for me - I'm new to PIX configuration If Yes please excuse my stupidity!

  I changed the config on our PIX to allow only access via SSH (rather than via telnet as it was previously configured)

  Now, everything works fine when I'm in the office - I can connect to the PIX using SSH without any problem.

  However, if I work from home and connect to the office using my VPN client (IPSEC tunnel ends on the PIX firewall itself) I find that I can not connect to the PIX.

  I have configured the PIX to access ssh on the office LAN subnet and the client pool of IP addresses used for VPN connections by using the following commands:

  SSH 172.64.10.0 255.255.255.0 inside

  SSH 192.28.161.0 255.255.255.0 inside

  where the 1st line is reference to the office's LAN, which works very well, and the 2nd line denotes the IP address pool configured on the PIX for VPN access.

  Can someone tell me how to fix this? I have the feeling that its something pressing!

  Thank you

  Neil

  Try the command "management-access to the Interior.

• Several connections of client XAuth of PIX 506th

  Hi, we have Cisco PIX 506th, fully updated:

  Cisco PIX Firewall Version 6.3 (5)

  Cisco PIX Device Manager Version 3.0 (4)

  We have two customers with Cisco (routers with VPN and PIX firewall IOS). I can't make two IPSec connections for them using XAuth (they allowed Xauth). I see that we have only one VPN connection with extended authentication (XAuth) called "Easy VPN. When I am trying to set up a new one it replaces just my old connection. If I shouldn't use this firewall PIX Easy VPN Client, how can I use extended authentication (XAuth) I found no option for this? Is this supported? At 25 connections how to only IPSec connections without XAuth authentication data sheet?

  as far as I know, you may need an additional device. as mentioned, the reason being a single unit can act as a client for two ezvpn ezvpn different servers.

  Otherwise, you must return to the type of vpn. that is, to set up lan - lan.