PIX VPN accounts

Similar Questions

• Simple PIX PIX VPN issues

  I'm trying to implement a simple PIX PIX VPN using the simple PIX - PIX VPN documentation for the sample config page. I have a lot of VPN tunnels with other very happy other PIX devices so it's quite annoying. Anyway, on the source PIX config is as follows:-

  access-list 101 permit ip 172.18.138.0 255.255.255.0 172.18.133.0 255.255.255.0

  access-list 101 permit ip 172.18.133.0 255.255.255.0 172.18.138.0 255.255.255.0

  NAT (phoenix_private) 0-access list 101

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac chevelle

  ntlink 1 ipsec-isakmp crypto map

  1 ipsec-isakmp crypto map TransAm

  correspondence address 1 card crypto transam 101

  card crypto transam 1 set peer 172.18.126.233

  card crypto transam 1 transform-set chevelle

  interface inside crypto map transam

  ISAKMP allows inside

  ISAKMP key * address 172.18.126.233 netmask 255.255.255.255

  ISAKMP identity address

  part of pre authentication ISAKMP policy 1

  of ISAKMP policy 1 encryption

  ISAKMP policy 1 md5 hash

  1 1 ISAKMP policy group

  ISAKMP policy 1 lifetime 1000

  and if I generate the traffic logs show this: -.

  9 August 18:40:15 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:17 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:18 10.60.6.247% PIX-3-305005: no group of translation not found for udp src phoenix_private:172.18.138.111/3832 dst inside:172.18.133.51/53

  9 August 18:40:18 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:19 10.60.6.247% PIX-3-305005: no group of translation not found for udp src phoenix_private:172.18.138.111/3832 dst inside:172.18.133.51/53

  No isakmp and ipsec debugging message appears, but you who wait that the PIX does not even link the traffic with the access list or a NAT.

  I do something obviously stupid, can someone tell me what it is, thank you.

  Jon.

  Hello

  1. you create a second access as list:

  outside_cryptomap ip 172.18.138.0 access list allow 255.255.255.0 172.18.133.0 255.255.255.0

  and

  2. instead of

  correspondence address 1 card crypto transam 101

  You must configure

  card crypto transam 1 match address outside_cryptomap

  the problem is that you configure an ACL for nat and crypto - that does not work

  concerning

  Alex

• With PAT on Cisco PIX VPN client

  Dear all,

  I have a PIX 515 to the main site with the IPSec security is enabled. Homepage user using 3.x VPN client connects to the PIX for VPN access. When user Home use real IP, I can ping to the local network of the main site. However, when the Home user using a router with PAT, the VPN can be established.

  Is there a setting I should put on PIX, VPN client or router?

  Thank you.

  Doug

  And if you still have problems, upgrade your pix, 6.3 and usage:

  ISAKMP nat-traversal

  But the first thing would be to check the IPSEC passthrough as Ade suggested. If the device is a linksys check the version of the firmware as well.

  Kind regards

• On Pix VPN tunnel to the same subnet

  I have a customer who want to set up a the PIX VPN tunnel located on each site. For some reason, each side has the same subnet number, for example. 10.10.10.x/32. I'm sure we must run NAT, but is it possible.

  This can help

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800949f1.shtml

• Client pix VPN how to authenticate with Active Directory

  Hi all, I've just set up my first Client VPN on a Cisco PIX. Everything works very well so that hitting the correct subnet and logon. However, I would like to see how I can get my connection of remote users with there active directory accounts. Right now I use the local connection for the pix for testing purposes. Sounds easy, but I'm missing something

  We use:

  Cisco Pix 515E version 6.3 (3)

  Thank you

  Dan

  Unfortunately the PIX 6.3.3 version does not support Active Directory authentication. V6.3.3 PIX only supports authentication to the server database, radius, and Ganymede local PIX.

  If you want to authenticate to active directory, it is support for PIX v7.x go.

  Here are the different types of authentication support for PIX v7.x leave for your reference:

  http://www.Cisco.com/en/us/docs/security/ASA/asa70/configuration/guide/AAA.html

  Hope that answers your question.

• Cisco PIX VPN pass through (sorry, tricky!)

  Hello

  I'm having some problems with allowing IPSEC through a Cisco PIX 501. The configuration is the following:

  Host (mail Client) (192.168.1.111)

  |

  PIX (NAT)

  |

  INTERNET

  |

  (Checkpoint) VPN server

  The problem is, the PIX guard dropping my outgoing isakmp packets on its * internal * inetrface!

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  Does anyone know why it does this? Anyting to my in-house (security level 100) should go directly to my giving and external interface on the net. For some reason, is to treat the isakmp packets differently...

  I have included my config as an attachment, can we see what I missed or have any ideas why it loses the isakmp packets?

  Thanks for any help.

  Nick Chettle

  Check users. C and edit it with your favorite editor. Check if you have a private or public IP address!

  I tried to find in the really safe base article I've seen a couple of months ago but I can't find any more.

  https://SecureKnowledge.checkpoint.com/SK/public/intro.jsp

  See also this FAQ:

  http://www.phoneboy.com/bin/view.pl/FAQs/SecureClientFAQs

  See CheckPoint VPN-1 Guide that is on the installation CD or go to the web site of checkpoints, BUT you need a valid account Center user to read and download the documentation. Start looking at page 119 and 211.

  As usual, nothing is free at the checkpoint.

  http://www.checkpoint.com/support/technical/documents/docs_r55.html

  sincerely

  Patrick

• PIX PIX VPN - error log

  I created a VPN between our PIX and PIX customers but receives the following error message when I try to activate tunnnel. I checked the ACL on both ends. Any ideas?

  ISADB: Reaper checking HIS 0x80da9618, id_conn = 0IPSEC (sa_initiate): ACL = deny;

  No its created

  IPSec (sa_initiate): ACL = deny; No its created

  IPSec (sa_initiate): ACL = deny; No its created

  IPSec (sa_initiate): ACL = deny; No its created

  I've seen a few times. Usually remove the interface of the card encryption and re - apply solves it, sometimes it is necessary to remove the card encryption and the "enable isakmp outside" and put them both back in.

  This message is also sometimes to do with something wrong in the configuration, in order to double-check your ACL and your transformation games, etc.

• Add PIX VPN to the already established network of MPLS

  I have a client who operates the site three on a MPLS cloud. Now they want to add more security between these different places. A place internet offers to the United Nations. However, all sites can communicate securely with each other.

  Each location has its own 10... subnet.

  They believe as a PIX at every place on every 10. / subnet and VPN tunnels between each PIX, it's what it takes.

  Is there a third party place connections between these PIX on their MPLS VPN cloud?

  Thanks cowtan. Please mark as resolved post, which might be useful for others. response rate (s) If you found useful responses...

• ping for the pix vpn problem

  Hello

  I got a pix 501 (6.3 - 4) on a local network and try to use Cisco VPN Client (4.0.2-D) on a remote pc.

  I can open a vpn session.

  I can't ping from the remote pc to the LAN

  I can ping from any station on the LAN to the remote pc

  After that I did a ping of a station on the LAN to the remote pc, I ping the remote computer to the local network.

  I am so newb, trying for 2 days changing ACLs, no way.

  I must say that I am in dynamic ip wan on the local network and the remote pc.

  Any idea about this problem?

  Any help is welcome.

  Here is the configuration of my pix:

  6.3 (4) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password * encrypted

  passwd * encrypted

  pixfirewall hostname

  domain ciscopix.com

  clock timezone THATS 1

  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  correction... /...

  fixup protocol tftp 69

  names of

  name 192.168.42.0 Dmi

  inside_access_in ip access list allow a whole

  inside_outbound_nat0_acl ip access list allow any 192.168.229.0 255.255.255.0

  outside_cryptomap_dyn_20 ip access list Dmi 255.255.255.0 allow 192.168.229.32 255.255.255.224

  access-list outside_cryptomap_dyn_20 allow icmp a whole

  pager lines 24

  opening of session

  logging trap information

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside the 209.x.x.x.255.255.224

  IP address inside 192.168.42.40 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool dmivpndhcp 192.168.229.1 - 192.168.229.254

  location of PDM 192.168.229.1 255.255.255.255 outside

  209.165.x.x.x.255.255 PDM location inside

  209.x.x.x.255.255.255 PDM location outdoors

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 209.165.200.225 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  Dmi 255.255.255.0 inside http

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  TFTP server inside the 192.168.42.100.

  enable floodguard

  Permitted connection ipsec sysopt

  AUTH-prompt quick pass

  AUTH-guest accept good

  AUTH-prompt bad rejection

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  Dynamic crypto map dynmap 20 match address outside_cryptomap_dyn_20

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  vpngroup address dmivpndhcp pool dmivpn

  vpngroup dns 192.168.42.20 Server dmivpn

  vpngroup dmivpn wins server - 192.168.42.20

  vpngroup dmivpn by default-field defi.local

  vpngroup idle 1800 dmivpn-time

  vpngroup password dmivpn *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN username vpnuser password *.

  VPDN allow outside

  VPDN allow inside

  dhcpd address 192.168.42.41 - 192.168.42.72 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  Terminal width 80

  Cryptochecksum: *.

  Noelle,

  Add the command: (in config mode): isakmp nat-traversal

  Let me know if it helps.

  Jay

• PIX vpn public dmz

  Hello

  I d wishes to establish a vpn to a pix firewall 515 and pos version

  7.0 (5) with a public dmz and nat translation.

  inside: 10.5.10.0/24

  outdoors: 1.1.1.1/27 (Beach)

  DMZ: 2.2.2.2/27 (Beach)

  distance inside the network:192.168.20.0/24

  My area of encryption should be: 2.2.2.3/32--192.168.20.0/24

  announcement I have a nat rule, which is:

  NAT (inside the dmz) 2.2.2.3 10.5.10.28 netmask 255.255.255.255

  So basically I want to translate the connections coming from 2.2.2.3 to

  10.5.10.28

  the vpn is configured correctly and set up both sides, but the nat rule

  with the vpn doesn't work.

  Built of incoming TCP connections to outside:192.168.20.82/34237 4619

  (192.168.20.82/34237) at dmz:2.2.2.3/22 (2.2.2.3/22)

  but I can t see any traffic on the 10.5.10.28 Server, I see instead:

  Built of incoming TCP connections to outside:192.168.20.82/34237 4619

  ((192.168.20.82/34237) at dmz:10.5.10.28/22(10.5.10.28/22)

  any help would be great!

  Kind regards

  dural

  Dural salvation

  Could you specify just the line

  NAT (inside the dmz) 2.2.2.3 10.5.10.28 netmask 255.255.255.255

  should we read

  2.2.2.3 static (inside the dmz) 10.5.10.28 netmask 255.255.255.255

  Also are you terminating the VPN on the external interface of your firewall is to say what is the IP address of the peer to your end.

  You might not try

  static (inside, outside) 2.2.2.2 10.5.10.28 netmask 255.255.255.255

  * Edit - I meant

  static (inside, outside) 2.2.2.3 10.5.10.28 netmask 255.255.255.255 *.

  You need not actually traffic to DMZ, you?

  If not do you have IP addresses available in the public system on your external interface?

  HTH

  Jon

• Replication failover PIX VPN (CEP) certificate

  Hello

  Had a pair of PIX 525 on 6.3 (4) version running in active/failover mode, I recently configured VPN authenticated by certificates, which involved the use of PRACTICE in order to get the certificate to the PIX. Certificates have been imported for the PIX from a snap-in with the software component CEP Protocol Windows CA server by following the instructions described here: http://www.ciscosystems.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html#wp1007263 .

  It all works very well, the configuration has been saved, certificates registered cases using "ca save all", everything works well except the certificates that have been imported have not been replicated for the PIX failover - the command 'Show the ca certificate', shows not all certs.

  Private keys show 'sh ca mypubkey rsa' are the same on both devices.

  I'm not able to find any documentation about how certificates must be replicated on the PIX failover, and it is not possible to write certificates again on the PIX failover using the commands they were initially imported by:

  PIX - fw # conf t
  WARNING *.
  Configuration of replication is NOT performed the unit from standby to Active unit.
  Configurations are no longer synchronized.

  PIX - FW (config) auth ca ca
  WARNING *.
  Configuration of replication is NOT performed the unit from standby to Active unit.
  Configurations are no longer synchronized.

  Everyone knows a similar issue or how to get the PIX failover with the new ca certificates?

  Kind regards

  Sarunas

  Hello Sarunas

  PIX 6 indeed do not synchronize keys and certificates automatically.

  However, you should be able to do this first, forcing a failover (i.e. secondary image make it active), then register (now active) high school with the certification authority.

  HTH

  Herbert

• Site to Site PIX VPN problems

  Hi, I currently have a site to site vpn upward and running and it works fine. I try to put the other two online and just cannot make them work. I used the same configuration of one operation but I cannot get the next tunnel. I saw several errors when debugging isakmp and ipsec and they are at the end of my configs. Anyone have any ideas? Thank you

  Main site - a vpn clients connecting too it and pt to pt vpn to 3 endpoints

  Cisco PIX Firewall Version 6.3 (3)

  * Main Site Config *.

  client_vpn 10.10.0.0 ip access list allow 255.255.0.0 192.168.0.0 255.255.255.0

  VPN_to_Site2 10.10.0.0 ip access list allow 255.255.0.0 192.168.0.0 255.255.255.0

  NAT (inside) 0-list of access client_vpn

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-3des esp-md5-hmac fws_encry_set

  outside_map 60 ipsec-isakmp crypto map

  address for correspondence card crypto outside_map 60 VPN_to_Site2

  crypto outside_map 60 peer 64.X.X.19 card game

  card crypto outside_map 60 transform-set fws_encry_set

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 64.X.X.19 netmask 255.255.255.255 No.-xauth-no-config-mode

  ISAKMP identity address

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  Site 2 config

  * only because the pt to pt does not work I have it set up to allow vpn clients to cross to connect to the main site.

  Cisco PIX Firewall Version 6.3 (5) *.

  permit access ip 192.168.0.0 list VPN_to_Main 255.255.255.0 10.10.0.0 255.255.0.0

  NAT (inside) 0-list of access VPN_to_Main

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-3des esp-md5-hmac fws_encry_set

  outside_map 10 ipsec-isakmp crypto map

  outside_map card crypto 10 corresponds to the address VPN_to_Main

  crypto outside_map 10 peer 207.X.X.13 card game

  card crypto outside_map 10 transform-set fws_encry_set

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 207.X.X.13 netmask 255.255.255.255 No.-xauth-no-config-mode

  ISAKMP identity address

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  Errors

  PIX (config) # IPSEC (sa_initiate): ACL = deny; No its created

  authenticator is HMAC-MD5IPSEC (validate_proposal): invalid local address

  I have a link that works very well. I have copied the config from there, changed the ip info and it does not work. The only differences in the configs are no sysopt route dnat and it's on Version 6.2 (2)

  IPSec (sa_initiate): ACL = deny; No its created

  I think that you have configured a VPN tunnel without removing the cryptographic card of the external interface. The message above is the error we get in such situation.

  I suggest the following solution:

  -remove the external interface (the two pix) cryptographic card

  -Cree claire isa his and trendy clear ipsec his (the two pix)

  -Reapply the card encryption on external interfaces.

  If this doesn't solve the problem, restart the equipment.

  Kind regards

  Ajit

• (Maybe stupid) Question about ASDM configured PIX PIX VPN

  I have two PIX515 running v7.2 (1) and ASDM 5.2 (1).

  If I use the VPN Wizard of the ASDM to configure a site to site VPN, this process takes care of the need to create split tunnel parameters, so that the outgoing traffic non - VPN inside each PIX is managed properly?

  Hello

  By default, all client VPN traffic is encrypted and sent to the VPN server, Split tunneling is used for client vpn remote to exempt a particular traffic to be encrypted and tunnel to the VPN server so that the traffic will be sent in parallel to the internet or local.

  During the configuration of site to site intuitively that when the configuration of the remote networks on both sides that communicate together by the IPSec tunnel and all other traffic is routed to their destinations without encryption.

• PIX-to-PIX VPN does not

  Here is my configuration:

  local-pix 501 connected to the DSL line.

  506th pix remote control connected to the dsl line

  unique IP address routable on each PIX (so using PAT, no NAT).

  try to create a site to site vpn. Tried of PDM, CLI via documentation cisco CLI via the book of Richard Deal. I can apparently make the connections, but no traffic flows. I have no idea what I'm doing wrong. Here are the relevant configs:

  PIX of premises:

  6.3 (3) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password

  passwd

  hostname encima

  domain name gold - eagle.org

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list outside_access_in allow accord 64.144.92.0 255.255.255.128 no matter what newspaper

  outside_access_in list of access permitted tcp 64.144.92.0 255.255.255.128 eq pptp pptp log any eq

  outside_access_in list access permit icmp any any echo response

  access-list outside_access_in allow icmp all once exceed

  outside_access_in list access permit icmp any any source-quench

  outside_access_in list all permitted access all unreachable icmp

  outside_access_in list of permitted access esp 66.159.222.109 host 67.100.95.114

  outside_access_in list of permitted access esp 67.100.95.114 host 66.159.222.109

  access-list 90 allow ip 172.17.0.0 255.255.255.0 172.24.1.0 255.255.255.0

  pager lines 24

  opening of session

  registration of information monitor

  logging buffered information

  ICMP permitted host 67.100.95.114 outside

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside x.x.x.109 255.255.255.0

  IP address inside 172.17.0.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 172.24.1.0 255.255.255.0 outside

  location of PDM 172.17.0.0 255.255.255.0 outside

  location of PDM 64.144.92.0 255.255.255.128 outside

  location of PDM 172.17.0.0 255.255.0.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0-90 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 66.159.222.1 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  Enable http server

  x.x.x.x 255.255.255.255 out http

  x.x.x.x 255.255.255.128 out http

  http 172.17.0.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set strong esp-3des esp-sha-hmac

  toEssex 20 ipsec-isakmp crypto map

  correspondence address card crypto 20 90 toEssex

  peer set card crypto toEssex 20 67.100.95.114

  toEssex 20 set transformation-strong crypto card

  toEssex interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 67.100.95.114 netmask 255.255.255.255

  part of pre authentication ISAKMP policy 9

  ISAKMP policy 9 3des encryption

  ISAKMP policy 9 sha hash

  9 1 ISAKMP policy group

  ISAKMP policy 9 life 86400

  Telnet 172.17.0.0 255.255.255.0 inside

  Telnet timeout 60

  SSH x.x.x.x 255.255.255.128 outside

  SSH timeout 60

  Console timeout 0

  dhcpd address 172.17.0.2 - 172.17.0.32 inside

  dhcpd dns x.x.x.100 66.218.44.5

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  username ckaiser password * encrypted privilege 15

  Terminal width 80

  Cryptochecksum:xxxxxx

  : end

  PIX remotely:

  6.3 (1) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password

  passwd

  EVL-PIX-DSL host name

  domain essexcredit.com

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  access-list outside_access_in allow accord any any newspaper

  outside_access_in list access permit tcp any any eq pptp newspaper

  outside_access_in list access permit icmp any any echo response

  access-list outside_access_in allow icmp all once exceed

  outside_access_in list access permit icmp any any source-quench

  outside_access_in list all permitted access all unreachable icmp

  outside_access_in esp x.x.x.114 host 66.159.222.109 host allowed access list

  outside_access_in list of permitted access esp 66.159.222.109 host 67.100.95.114

  access-list 80 allow ip 172.24.1.0 255.255.255.0 172.17.0.0 255.255.255.0

  pager lines 24

  opening of session

  timestamp of the record

  monitor debug logging

  logging buffered information

  recording of debug trap

  history of logging warnings

  logging feature 22

  ICMP permitted host x.x.222.109 outdoor

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside x.x.x.114 255.255.255.248

  IP address inside 172.24.1.240 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM location x.x.x.x 255.255.255.255 outside

  location of PDM 172.24.1.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 80 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 67.100.95.113 1

  Route outside x.x.x.0 255.255.0.0 66.159.222.109 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  Enable http server

  x.x.x.x 255.255.255.255 out http

  http 172.24.1.0 255.255.255.0 inside

  SNMP-server host within the 172.24.1.11

  Server SNMP Emeryville, CA location

  Server SNMP contact Charlie Kaiser

  snmp4esx SNMP-Server community!

  SNMP-Server enable traps

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set strong esp-3des esp-sha-hmac

  toEncima 10 ipsec-isakmp crypto map

  correspondence address card crypto 10 80 toEncima

  peer set card crypto toEncima 10 66.159.222.109

  toEncima card 10 game of transformation-strong crypto

  toEncima interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 66.159.222.109 netmask 255.255.255.255

  part of pre authentication ISAKMP policy 8

  ISAKMP strategy 8 3des encryption

  ISAKMP strategy 8 sha hash

  8 1 ISAKMP policy group

  ISAKMP life duration strategy 8 the 86400

  Telnet 172.24.1.0 255.255.255.0 inside

  Telnet timeout 60

  SSH x.x.x.x 255.255.255.255 outside

  SSH timeout 60

  Console timeout 0

  username ckaiser password * encrypted privilege 15

  Terminal width 80

  Cryptochecksumxxxxxx

  : end

  When I try to ping an address on the net since the first pix of 172.24, I get no response. When I try to ping an address on the net since the second pix 172,17, I get no response. Connectivity Internet is fine. I can ping the addresses outside each pix OK.

  My debug output for isakmp shows the State of return is IKMP_NO_ERROR and the SAs look OK; everything matches. Several configs / debugs available upon request.

  No idea why I can't get from one network to the other?

  Thank you!

  Charlie Kaiser

  "When I try to ping an address on the net since the first pix of 172.24, I get no response. When I try to ping an address on the net since the second pix 172,17, I get no response. »

  It could be as simple as because you try to ping from the PIX (because you can't) and your tunnel could in fact be working properly

  Try to ping from a device on 172,17 to one in 172.24.

  (Make sure that your access point to the opposing LAN for these host devices are set to be the PIX)

  HTH

• block access to the local asa firewall vpn accounts

  I'm looking for the local accounts on the firewall and would like to make sure that users who have local accounts for vpn do not have for the firewall itself through asdm, telnet, ssh to the management.

  Is the only aaa on the firewall command

  the ssh LOCAL console AAA authentication

  With this command, if I change the local account setting to 'NO ASDM, SSH, Telnet or access Console' (see attached screenshot) will that still allow users to vpn in and access the network because they have to take off but any what potential access to the firewall?

  Thank you

  Hello

  Yes, if you select the option "No., ASDM, SSH, TELNET or Console access" allows to block only the admin access to the firewall. Here's the equivalent CLI for this option:

  myASA(config-username) # type of service?

  the user mode options/controls:
  Admin user is authorized to access the configuration prompt.
  NAS-prompt user is allowed access to the exec prompt.
  remote user has access to the network.

  If you use this option you will be on the third option in the above list that is remote access. Users will have the option of VPN in but no admin (asdm, ssh, telnet or console)

  Thank you

  Waris Hussain.