Add PIX VPN to the already established network of MPLS

Similar Questions

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.

• Simple PIX PIX VPN issues

  I'm trying to implement a simple PIX PIX VPN using the simple PIX - PIX VPN documentation for the sample config page. I have a lot of VPN tunnels with other very happy other PIX devices so it's quite annoying. Anyway, on the source PIX config is as follows:-

  access-list 101 permit ip 172.18.138.0 255.255.255.0 172.18.133.0 255.255.255.0

  access-list 101 permit ip 172.18.133.0 255.255.255.0 172.18.138.0 255.255.255.0

  NAT (phoenix_private) 0-access list 101

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac chevelle

  ntlink 1 ipsec-isakmp crypto map

  1 ipsec-isakmp crypto map TransAm

  correspondence address 1 card crypto transam 101

  card crypto transam 1 set peer 172.18.126.233

  card crypto transam 1 transform-set chevelle

  interface inside crypto map transam

  ISAKMP allows inside

  ISAKMP key * address 172.18.126.233 netmask 255.255.255.255

  ISAKMP identity address

  part of pre authentication ISAKMP policy 1

  of ISAKMP policy 1 encryption

  ISAKMP policy 1 md5 hash

  1 1 ISAKMP policy group

  ISAKMP policy 1 lifetime 1000

  and if I generate the traffic logs show this: -.

  9 August 18:40:15 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:17 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:18 10.60.6.247% PIX-3-305005: no group of translation not found for udp src phoenix_private:172.18.138.111/3832 dst inside:172.18.133.51/53

  9 August 18:40:18 10.60.6.247% PIX-3-305005: no translation not found for icmp src phoenix_private:172.18.138.111 dst domestic group: 172.18.133.51 (type 8, code 0)

  9 August 18:40:19 10.60.6.247% PIX-3-305005: no group of translation not found for udp src phoenix_private:172.18.138.111/3832 dst inside:172.18.133.51/53

  No isakmp and ipsec debugging message appears, but you who wait that the PIX does not even link the traffic with the access list or a NAT.

  I do something obviously stupid, can someone tell me what it is, thank you.

  Jon.

  Hello

  1. you create a second access as list:

  outside_cryptomap ip 172.18.138.0 access list allow 255.255.255.0 172.18.133.0 255.255.255.0

  and

  2. instead of

  correspondence address 1 card crypto transam 101

  You must configure

  card crypto transam 1 match address outside_cryptomap

  the problem is that you configure an ACL for nat and crypto - that does not work

  concerning

  Alex

• Add an element to an already defined balance

  Hi dear,
  
  I have a balance set for the total of the payments. Now, I have defined one of the several other elements that should be part of this flow of balance.
  How can I add this element to the already defined balance?
  
  Any help?

  Is based on the legislation that you work.
  Some laws like the Spain have a seeded balance "Total payments".
  UK a - "total compensation."

  If it's a balance seeded, you will not be able to add anything. Everything will be greyed out.

  You can check of seeded dorsal - balances

  Select * from pay_balance_types
  where legislation_code = 'GB'
  

  User-defined all those who have populated business_group_id

  Select * from pay_balance_types
  where business_group_id = 82;
  

  The foregoing also applies with all the tables, i.e. If Legislation_code is filled then planted another if Business_group_id is populated then defined customer.

  A request for the definition of your balance and view the stream. It shows the value to pay for the added element?

  See you soon,.
  Vignesh

• Add a vpn connection in ios 10, method chosen in IKEv2, but I don't have the remote ID. My VPN is created in Sonicwall

  Add a vpn connection in ios 10, method chosen in IKEv2, but I don't have the remote ID. My VPN is created in Sonicwall, waiting for quick reply

  Hi cmscan,

  Thank you for using communities of Apple Support.

  I see that you add a VPN connection using IKEv2, but you do not have the remote ID. I know it's important to be able to set up a virtual private network, you can connect using your iPhone. I'm happy to help you with this.

  You must contact your system administrator to ensure that the settings that you must configure the VPN connection. Please see the iPhone user Guide for more information.

  Have a great day!

• When I try to add a VPN connection, I get an error that the wizard is unable to connect. I am running Windows Vista.

  When I try to add a VPN connection, I get an error that the wizard is unable to connect.  I am running VISTA. I want to simply add a VPN and be able to connect to a non-profit organization where I volunteer.  My VPN working two weeks ago.  Then my shortcut did not work, and this problem started.

  Any help is appreciated.

  original title: VPN Vista issues

  Hello

  Thank you for visiting the Microsoft answers community site. Your question of Windows Vista is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Vista Networking forum.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro

• Adding a printer already installed on the pc for the home group network

  I want to add a printer that is already installed on my computer for the home group network. Because it is already installed, it does not appear when the computer search possible printers to be added. I don't want to uninstall and reinstall - our relationship is much fragile. Help, please.

  Hello

  See if this helps you:

  http://Windows.Microsoft.com/en-us/Windows/install-printer-home-network#1TC=Windows-7

  Setting up a shared printer

  "The most common way to make a printer available to a home network is traditionally to connect to one of the computers and then tell Windows to share it. This is called a shared printer.

  The advantage of sharing a printer is that it works with any USB printer. Side tilted? The host computer must always be fed up, otherwise the rest of the network will not be able to access the shared printer. »

  ________________________________

  Homegroup: recommended links

  http://Windows.Microsoft.com/en-us/Windows7/HomeGroup-recommended-links

  Read this section:

  'Connecting to homegroup printers' under ' access to files and printers on other computers in the homegroup.

  http://Windows.Microsoft.com/en-us/Windows7/access-files-and-printers-on-other-HomeGroup-computers

  See you soon.

• PIX from site to site VPN at the Juniper

  Hello world

  have a problem with the vpn site to site configuration beetween cisco pix and juniper firewall.

  When I entered the command "show isakmp crypto its" Cisco Pix console displays the following status:

  State

  OAK_CONF_ADDR

  But I don't know what it means that State

  or what is the problem?.

  l think my setup is corret.

  I also have VPN clients configured on the network, and they run correctly.

  can someone help me! Plase...

  Thanks a lot. = D

  If phase 1 is completed successfully, you will see QM_IDLE in "isakmp crypto to show his". Therefore, this suggests a problem of phase 1 - orders «isakmp...» ».

  Check the policy, check the pre-shared key.

  "CONF_ADDR" gives to think that one end looking for mode config (address IP etc) with the other.

  See line «isakmp key...» « a »... No.-xauth No.-config-mode"at the end.

• Multiple connections to the PIX VPN

  Is it possible to put an end to a simple VPN for the PIX to provide remote access, but at the same time set up an another tunel VPN between the PIX and another firewall to provide access from the internal network to the external?

  Thanks in advance!

  Yes, you can have client and L2L tunnels configured on the pix together. If you talk to redirect traffic so that the customer can speak through the L2L at the remote network as well, here's a link: http://www.cisco.com/warp/public/110/client-pixhub.html

  Here is a link to just the client for the pix configuration:

  http://www.Cisco.com/warp/public/110/pix3000.html

  or here's a link on the conduct of pix pix and customer:

  http://www.Cisco.com/warp/public/110/pixpixvpn.html

  Kurtis Durrett

• Unable to add the virtual machine network services

  Hello:

  I already read that warning Virtual PC 2007 is not compatible with win 7-64.
  However, I read that it is "unofficially" possible launch.
  OK, I installed it and it worked except networking.
  Basically, I need to install the Virtual Machine Network Services.
  I right click on my network card-> properties-> install-> services-> virtual machine network services (VPC2007 folder: where I can see VMNetSrv.inf)
  Then says Windows: it is impossible to add the requested feature. The specified service has been marked for deletion.

  The problem is that I get this error even on WinXP SP3, so I think that there is something else wrong.

  And of course, Virtual PC 2007 available networks are only: no connection, Local, NAT.  (Missing my physical adapter)

  Thank you!!!

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads

  Hope this information is useful.

• Aks whenever Firefox be the standard browser - although it is already established

  Since the last update for windows firefox 8.1 ask every time to be the standard browser. In the windows settings (standard programs), it is already established as such. But in the Firefox settings (General provisions), it is shown constantly to be non-standard.

  You can disable the application by going to menu > Preferences > general, then uncheck the box that says always check to see if firefox is the default browser. I would also try that in fact the default browser from here, see if that helps.

• No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Original title: no local network connection

  No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Hi H.mustafaakyurek,

  ·         What operating system is installed on your computer?

  You can view the following items on the creation of a network connection:

  Setting up a network home

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

   

  Start here to set up a home network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

   

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Also see the following articles on the connection of an Internet connection:

  What do I need to connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/what-do-I-need-to-connect-to-the-Internet

   

  Allows to connect to the Internet mobile broadband

  http://Windows.Microsoft.com/en-us/Windows7/use-mobile-broadband-to-connect-to-the-Internet

  Hope this information helps.

• I can't access my email works through outlook over a VPN. The signin VPN works ok, I can see my network co., but can not use outlook. 'Microsoft Exchange Server' reported an error (0 x 80040115)

  prospects for bt infinity

  I recently changed my home to infinity of BT broadband.  Now I can't access my email works through outlook over a VPN.  The signin VPN works ok, I can see my network co., but can not use outlook.   I get the following error at startup of outlook.

  Task 'Microsoft Exchange Server' reported an error (0 x 80040115): ' the connection to the Microsoft Exchange Server is unavailable.  Outlook must be online or connected to complete this action. »

  Anyone have any ideas?

  Allan M

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  Kind regards

  Ramata Thakur

• How can I add my laptop to the network and connect to the internet as well

  I have internet access on my computer at home, the ipod, the ipad and iphone.  How can I add my laptop to the network and connect to the internet as well?

  Hello

  I suggest you to refer to the following Microsoft article and check if it helps.

  Add a device or computer to a network:

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-a-device-or-computer-to-a-network

  For more information, see the following Microsoft article.

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-you-need-to-set-up-a-home-network

  http://Windows.Microsoft.com/en-us/Windows/explore/home-networking

  Hope the information is useful.

• Unable to connect to the internet and VPN in the network.

  I have an ADSL account and when I vpn in our network using cisco VPN 3015 vpn client can't access the internet more locally. I have to use our internal proxy server on the network. Is it possible to make the vpn tunnel but also use the local internet DSL for browsing connection?

  You must set up split tunnelling tunnel, while only some packets are sent through the tunnel, the rest get out in clear packages just as usual.

  In 3015, create a list of network under Config - Mgmt policy - traffic Mgmt - list networks, this list includes your internal networks (you want to be dug traffic). Then go under the group to which the client connects to, on the Client configuration tab, select only the network of tunnels in the list, and then select your list from the drop-down list box. Reconnect and're you good to go.

  Keep in the spirit of split-mining is considered a bit of a security risk because your PC is now accessible from the Internet AND you have a VPN directly in your internal network. If someone can take possession of your PC, then they have access to everything. You can also watch in allowing both client firewall stuff.