Portege M100 runs at 600 MHz after the BIOS/FRIMWARE upgrade

Similar Questions

• Portege Z930-118 does not start after the BIOS update

  My PORTEGE Z930-118 failover and wont start after I upgrade in the middle of the upgrade I remove power, then press stop down after I see the power and wireless but the screen stays black?

  Any help please

  In this case the EPROM has to be reflashed once more using crisis disk BIOS.
  Usually this must be done by authorized maker Toshiba. But of course this will be possible only if the EPROM module has not been too bad.

  What to say: try procedure (link above) posted by Bob. In which case it will not work, ASP is your next contact point.

  Good luck

• Portege M100 PPM10A-0008GP & PPM10A-09E6M has the same motherboard?

  Portege M100 PPM10A-0008GP & PPM10A-09E6M has the same motherboard?

  Thank you very much!!!

  Portege M100 PPM10A-09E6M seems to confirm this hardware configuration:
  Intel Pentium M 1.3 GHz LV
  Graphics Controller Intel 855GM
  RAM 512 MB (installed) / 2 GB (max) - DDR SDRAM - PC2100 - 266 MHz
  Hard drive 80 GB

  The Portege M100 PPM10A-0008GP seems to support the Intel Pentium M 1.2 GHz, 256 MB and 60 GB HARD drive.

  But it seems that the motherboard must be the same.

• Windows XP Pro on which I run several programs. After the opening of a few applications, I have this message "not enough memory".

  Hello

  I have a PC running Windows XP Pro on which I run several programs. After the opening of a few applications, I have this message "not enough memory".
  When I have this message, I can't open another application, or those in Windows... I have 2 GB of memory and only 700 MB are used.
  If I open the calculator several times (about 65 times), I have the same result.
  Sometimes, I get no error message, but the application does not open.

  Someone knows why?

  Thank you

  Hello

  You did the chnages on computer before this problem?

  I suggest you go through the steps of the following atrticle.

  "Not enough memory" error message appears when you have a large number of programs running.

  http://support.Microsoft.com/kb/126962

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/ )
  How to back up and restore the registry in Windows.

• NB200 does not start after the bios - screen black screen with blinking cursor

  Hello

  I was using the laptop as usual when I think there may have been a virus activity - reason I say that is that my anti-virus closed unexpectedly. I couldn't restart programs files.

  I restarted the laptop.

  After the bios menu will I get a blank screen with a blinking cursor - windows does not start.

  I did the following:
  (1) create a USB bootable with Recovery Console window XP - boot with this i can see three drives C:, D: as SDA? I can see the content of these disks, so it seems that my HD works. I ran a fixmbr and fixboot, but this has not solved the problem.
  (2) create a Kaspersky bootable USB virus scan - ran it without problem - he found a few question (not on the disk boot sector) I've fixed.

  An option was to copy files from the laptop and then start it in recovery mode - so Itried to run the phone into recovery mode hold down the 0 key at startup - the bottom of the screen then displays * HDD Recovery mode * and nothing happens.

  Any help - other options would be greatly appreciated.

  My 1 year of that guarantee has expired a few months back so can't send in for repair.

  Thank you

  Hello

  I doubt that it is a virus.
  Seems the file system is damaged on the HARD drive and this is the reason why the laptop does not start until it could also be a partition of HARD disk malfunction.

  Try this; Turn on the unit, press F8, and then check if you have the laptop repair.
  If this is not possible, then you will need to reinstall new OS.

  Here you can order a recovery disc:
  http://backupmedia.Toshiba.EU/landing.aspx
  Of course you will need an external USB CD/DVD drive

• Satellite A500-138 60 fps instead of 99 fps after the BIOS update.

  Hello!

  Before I have a little problem with my fan, but I do it with the BIOS update. His work!

  Now, I have a little problem of different...
  I am a player of counter-strike and before the BIOS update I have 99.9 FPS now, I have about 60... Who is wrong?

  Its make me crazy...

  Hello

  Seems the CPU and GPU don t run full implementation after the BIOS update.
  Any performance CPU/GPU leads to lower the heat dissipation and this means that the cooling module does not need to execute quickly and very often.

  Check to see if you can change an option is the BIOS.
  You can also try to update a graphics driver and could control Windows 7 power management.
  Power management settings 7 victory could affect CPU and GPU performance to save battery power and reduce the heat dissipation.

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Satellite L300-1 has 3 - after the BIOS update, I get a BSOD

  I have a Satellite L300 1A 3 MODEL PSLB8E. I decided to update the version of the BIOS, thinking that he can resolve my issue of ethernet controller.

  But after the update, my laptop goes on infinite blue screen of death. How can I recover from this injury?

  Can someone please help.

  Hello

  Did you choose the good BIOS update for your model? Was it for Satellite L300 PSLB8E?

  What code you get BSOD?

  After the BIOS update you must always load the default settings. Maybe a bad BIOS setting is causing this BSOD.

• Satellite P200 - after the BIOS update I can't start the machine

  After the BIOS update I can't boot the laptop because the system doesn't recognize the relecommunicarions password.

  Before updating the password is 0000.
  After when I try to set the password incorrect password start apeeras

  The BIOS password can only be removed from an authorized service provider. So I think that there is no other way.

  On the Toshiba site, you can search the nearest:
  http://EU.computers.Toshiba-Europe.com

• Satellite U400 - after the BIOS update I can't start Windows

  I have laptop Toshiba Satellite U400, PSU44E and Win XP. After you have installed the new BIOS v. 3, 80-WIN32, it is not possible to start Windows, it always ends in restart. It is also not possible to reinstall Winsdows, as it always ends with the blue screen.

  Any help or suggestion?
  How can I install back my backup BIOS BACK?

  Hello

  Did you really choose the good BIOS for your laptop? Because on the Toshiba site Web are different models U400 has so you choose for PSU44E BIOS on Toshiba page?

  After the BIOS, you should load the default settings in the BIOS.
  Did you check that?

  A downgrade from the BIOS is not possible. This is possible only from an authorized service provider. So, you should contact them and ask a technician for help. I m sure they will help you. ;)

  Good bye

• Satellite A300 - after the BIOS update I can not install two OS

  Hello everyone:

  I bought a laptop Toshiba Satellite A300-247 with Windows Vista Home Premium.

  Then I formatted it and divided the hard (320 GB) into 6 partitions and installed Windows Vista and Windows XP on drive C to drive D after having changed the SATA controller mode in the BIOS for compatibility. The computer worked well with 2 operating systems. However, when I updated the BIOS to version 1.9, two operating systems stop working and one of them can be installed: XP can be installed when SATA controller mode is placed on compatibility and Vista can be installed only when the SATA is changed to AHCI.

  Is there is no explanation of what past? And can I install operating systems 2 together again?

  Thank you

  Hello

  First of all, I doubt that this has something to do with the BIOS update. I think that after the BIOS update HARD drive mode has been changed from AHCI to compatibility and therefore the OS didn't start.

  Anyway, in compatibility mode you can install Vista and XP without the SATA drivers. This should t be a problem.

  But do you know the difference between compatibility and AHCI? AHCI mode is faster and therefore I would recommend this mode.
  Like you said Vista you can already install in AHCI mode and for XP, you need Intel Storage Manager. This package includes the SATA drivers you need and here is a step by step guide to use these drivers:
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

  Last but not least, you can install 2 OS. You can do what you want! ;)

• My Tecra A2 only runs at 600 MHz

  After that I got my tecra A2 in service and change CPU and motherboard. I can't run faster than 600 MHz.
  I reinstalled and downloaded all avaleble upgrades.
  What should I do?

  Post edited by: chrismoh

  Hello

  Check this http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=1513

  Good bye

• Portege 7140 exist with 600 mhz?

  Hello
  I have a portege with P3 500 mhz, but my question is, 7140 exists with a P3 600 mhz speedstep? I can't find anything on the net...

  Hi zoddan

  I have the same information as you, and I'm sure that it has protected 7140 series with Pentium III processor and speed of 500 MHz.

• Solaris VM is not running on ESX4.0 after the conversion of VMware workstation 6.5

  I have created Solaris VM on VMware workstation 6.5, but now I want to run it on ESX 4.0. After the conversion of Solaris VM from VMware workstation in format by converter 4.0.This VMware ESX VM restarts again and again on the boot of power.

  VMware workstation is running on Intel (R) Xeon (R) CPU E5420 and ESX 4 running on the Unisys ES3220L system

  Help, please...

  How was the original virtual controller?

  If it's IDE, you will need to also change SCSI to IDE on ESX 4.0.

  André

• Tecra 8000 does not start after the BIOS update

  From one day to the other does not start my Tecra 8000 (400 MHz/256 MB BIOS 9.30 for years). After start-up, the disc starts to turn, but the screen including the backlight remains completely black, without red logo TOSHIBA BIOS is not accessible.

  I got a new mainboard on stock, so I replaced it, and it worked. Unfortunately now my WLAN card now did not work properly. I tried several settings of the BIOS with no results, so I decided to do an update of the BIOS from 7.50 to 9: 30. After the upgrade, I get the message "ROM WRITE successful, utility completed. LEADER BIOS: Tecra8000 v 9,30 ". Because what either kept silent, I pressed the power button to restart and heard a long and many short beeps (endless). I could interrupt what pressing the powerbutton for 5s.

  After turning on again I have the same problem as described in the first line :-( I can't get into the BIOS, but I can again update (with pressed F12). Once again these beeps.

  What to do with these beeps after average BIOS update? I replaced the MoBo connector LED with pension. Processor, memory, keyboard and HD has remained the same. So, before I start disassembling the machine, please notify, your help is very appreciated.

  Hello Joachim

  I'm not a technician and don t know what the beeps but I am afraid that the BIOS chip is damaged. Because of this, the unit is completely dead. Sorry, but I really don t believe you can do anything. Maybe the new motherboard again :(