My Tecra A2 only runs at 600 MHz

Similar Questions

• M200: Processor only works with 600 MHz - why?

  I noticed that when you change a pcb for a laptop regardless of the speed of processors it works to the slower which is 595/598 MHz.
  Have you noticed this? What is the reason behind?
  What is the solution?

  If the processor is to have 256MB / 512MB RAM this custom of things affect a large but for 1 GB & 2 GB the machine's performance becomes very problematic.
  I tried the update of DMI, it has not helped.
  Re-install os also did not help.
  The upgrade of BIO also did not help.
  Also I'm not very sure about this problem with a report any with pcbset change.
  With the right machine, I found the way that is switching dynamically from bios processor capabilities.
  In some machines that give problems I have not observed this option in the BIOS.

  The machines are PortA200 & Port M200 (tablet).
  someone can help me. I need to justify this to the customer.
  Thank you & best regards
  ChaitanyaN

  Hello

  This problem occurs after the change of motherboard. Usually after mainboard change it is very important to bring tests and diagnostic procedures. Without this procedure, the CPU works with fixed 600 MHZ.
  You should contact Toshiba service to resolve this problem of CPU.

  PS: This theme has been discussed here in the forum. Please check this:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=8492&MessageID=29400#29400
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=4351&MessageID=14808#14808

• Portege M100 runs at 600 MHz after the BIOS/FRIMWARE upgrade

  Hello

  I received a Portege M100, this week, installed Debian GNU/Linux (Sid) on it and almost everything was fine.
  Then I upgraded to the latest BIOS/FIRMWARE (from V1.10 to V1.50) and now my Pentium M 1200 MHz running at half speed.
  I can not load also cpufreq, which controls the speed of the cpu.

  I see this problem is already known, then:
  It will come a new BIOS/FIRMWARE fix for this?

  What do you mean by "I saw that this problem is already knowna? ¦ »
  Where do you find the description for a same problem?

  Usually the BIOS update should not have any influence 'wrong' on the speed of the CPU!

  Have you checked the BIOS option called "dynamic CPU frequency mode".

  This option is also in the Toshiba HWSetup. You can also switch between 'high' and 'always low '.

  concerning

• Re: Portege M200 - CPU runs only at 600 MHz

  Hello

  I bought a Dothan M755 2 GHZ processor for my M200. I installed the CPU with no problems, but now I have a: this CPU only runs at 600 MHZ. It seems to me that it works on the power saving mode, but I have the tablet on power supply.

  I tried an option in the bios to health, but there is nothing. My version is (seen in the top right corner in the bios): "ACPI BIOS Version 1.80"

  My OS is Windows 7 Prof

  Y at - it a possibility (update of the BIOS? etc.) to fix?

  Thanks for your support!

  Hey,.

  That s the speed step function and the kicks in the multiplier 5 x to save energy.

  Check the BIOS if you can find the setting on the speed step and turn it off. If you do not have such an option in the BIOS choose another plan and the value 100% minimum processor state. It will always run at 2.0 GHz.

  Check this box!

• Satellite L30-134 CPU upgrade question - running at 800 Mhz & 1300 Mhz

  Hi guys,.

  I recently updated my 1.4 for the Core Duo T5500 processor to give it more omff.
  I've updated the aswell of RAM with a 1 GB. It's worked well. Its now to 1.5 GB of RAM.

  The laptop goes off well and works well, the processor only runs at 800 mhz on each core occasionally he jumps up to 1300 mhz.
  I know what I downloaded CPUZ. I also tried to use old clockgen and the new version and it does not work.
  I also tried to use the NHC and no luck.

  I can't the voltage to run right or shift gears using clockgen. Also when I go into the Bios I can not change anything here either.
  I'm new to computer talk so the answers will have to be dumbed down for me in laymens terms.

  I'm shaw I read a post on the net saying they have this processor running at L30 - 134 here and it works great but can't seem to find him.
  I'm I shoot me in the foot, or can I get it to work?

  Hey Buddy

  I think that there is nothing wrong with your laptop or with the central unit.
  Is the processor Intel Core 2 Duo Mobile T5500 supports Enhanced Intel Speedstep _ technology and this is the reason why the speed of the CPU is not constantly running at 1.66 GHz.

  Please check this document on Enhanced Intel SpeedStep Technology Intel
  http://www.Intel.com/CD/channel/reseller/ASMO-na/Eng/203838.htm

  _It said: _ + Enhanced Intel SpeedStep technology allows the system to dynamically adjust the frequency of voltage and core processor, which can translate into a reduction in average energy consumption and decreases the average heat production.

  I think this should clarify everything!

  Good bye

• Portege M100 just run half the speed - 600 Mhz

  Hello
  I have a Portege M100 that I found very slow until I discovered it was running half speed (IE 600 mhz). I tried everything in the Bios and in Toshiba utility, but nothing to do: always clocked at 600 Mhz.

  Is there something I missed? y at - it 'special' something to do to allow him to run at full speed?

  I thank the of in advance to anyone who helps!

  Hello

  As already suggested that the firmware must be updated! This portable strange behavior happens especially if the technician forgot to update this laptop runs only at 600 MHz.

  Similar questions have been described a lot of time here in the forum.
  For example:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=1513
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=10244&MessageID=36320

  I always recommend the use of the forum advanced search before posting on similar problems!

• Qosmio F10-105 only works with the 600 MHz

  Hello

  My f10-105 run only @600 Mhz! in the bios and in power options I have select provincy.
  the verse of the bios. East of 1.20
  someone at - it an idea?

  THX

  Hello

  Usually after the replacement of the motherboard, it may happen that laptop runs just at 600 MHz. In this case you should contact the Service partner. The firmware must be written again. If the partner doesn't to do this, the machine runs at a speed fixed Service 600 MHz.

• Standby power problems M30-344 (CPU uses only 600 MHz)

  Hello!
  In my m30 344 motherboard and display are changed.
  Now I can't use the full 1.5 ghz cpu!
  In the power saver profile I can choose only the cpu rate of 1-3! I've now uninstalled this tool and reinstalled the version by the net. But I can use only 600 mhz!
  What can I do?

  [Edited by: admin 7 May 05 08:18]

  Hello

  As far as I know if the motherboard is changed the speed of the CPU will be around 600 MHz and in this case the service partner needs to update the CPU microcode. After that, the speed of the processor will be as before.

  I hope that you have already solved your problem with the speed of the processor.

• Portege 3480CT shows only 500 MHz instead of 600 MHz

  The manual mentions it as 600 Mhz machine, but mine never runs greater than 500 Mhz since I installed XP

  The 500 Mhz processor never leaves. I didn't know this until I installed a small utility to monitor the speed of the processor. The most I ever get is 500 Mhz. I don't know why it won't speedstep upward.

  I installed the software to save energy, but it was just a futile attempt

  Hello

  You can also check the hardware configuration tool. On the CPU tab you can set the CPU frequency mode. Try to set it to high. I believe that in this case the CPU will run with maximum speed constantly.

  Good bye

• Tecra 8100 running in 51 MHz FSB

  I use a Tecra 8100, PIII 600 MHz, 256 MB with Windows 2000. It seems to be too slow. So I used CrystalCPUID for more information about the system. It shows a cuurent Speed 301 MHz CPU and a 51 MHz instead of 100 MHz (FSB) system clock. How can I set the system up to 100 MHz (FSB) clock?

  I think that the current settings in the BIOS for CPU LOW speed and optimized battery. Check this.

• Satellite M30-801: CPU only works with a 600 MhZ

  Hi people, I have a strange problem since my PC back to toshiba support (lcd problem, on assistance report i red that the pcb has been replaced): my CPU goes up to 600 MhZ. I tried to update the version of the bios from 1.20 to 1.70 successfully and I have restored the default value believing it could be a related problem of bios , but nothing changes.

  The problem is present in a new installation of Windows XP (from recovery CD), so I think I could exclude a software problem.

  Any ideas?

  Thanks in advance
  Roberto

  Hello

  The update of BIOS does ' t solve this problem.
  It seems that the Toshiba service partner forgot to start several compatibility tests. This is necessary after some repair procedures. Without this additional test, the CPU does not work with maximum efficiency. Well, there is nothing to see. You must contact the service again and it should solve this problem.

• Portege M100 - blocked processor at 600 Mhz, have tried all BIOS versions

  Just my BIOS was about 1.20 when I went to site Web from Toshiba to get the drivers to install and to found the update the BIOS so I followed instructions burn it to a disk, the last one I have and I went, but after the update, I noticed that xp says he was clocked at 600 MHz not 1 2 GHz.

  So I used the cpuid to see if it is xp, but it shows as running 598,6 MHz processor and can flow to 600,4 MHz max so I went in the BIOS tried off sleep CPU max CPU and so restarted then I thought it was the xp so I reinstalled but still the same I used Suse Linux always the same.

  I've reflashed the BIOS with 1.50 through the same restarted windows. I get on where and it becomes ridiculous, even, I went and found all BIOS versions on the US site of Toshiba, which dates back to version 1.10 to 1.50, so I tried all the. Nothing!

  I am really puzzled that anyone can sort this is really boring and slow.
  Thank you in advance

  Hello

  Just a question; the motherboard has been replaced by the past?

  I know, after the replacement of the motherboard, the test & diagnosis must be performed in order to update the CPU microcode on the circuit board.
  If the firmware is not updated your CPU would be stuck at 600 Mhz.

  In order to update the firmware, the ASP must be contacted.

  The other reason why the CPU runs only at 600 Mhz is the setting low processing CPU Toshiba power saver.
  Check if the Toshiba power saver is installed on your laptop and set the options at a higher level.

  Check it out

• Can I use the latest version of Firefox. I have Win XP Pro PIII 600 Mhz. 3.6.25 excellent works, but I still get the message to be updated?

  I am so happy with Firefox 3.6.25 (thank you), but I'm worried update the program because the requirements of system does not respond to my PC or does it? I have Win XP Pro SP2, PIII 600 MHz I still get messages on your part on updating the program but do not know if it is possible.

  Stick with the version you have now. The versions of Firefox 4 + need a processor with SSE2 instruction set, as in the Intel P4 processors.

  http://www.Mozilla.org/en-us/Firefox/9.0/system-requirements/
  
  Recommended hardware

     * Pentium 4 or newer processor that supports SSE2
     * 512MB of RAM
     * 200MB of hard drive space
  

• 6730 b DEATH - only runs connected with no battery

  6730 b DEATH - only runs connected with no battery

  If I insert the battery while it is running connected, the PC will immediately dead.

  Any help on disgnosing what is the problem would be appreciated.

  Logic for me.  Thank you.  I'll post the results once I have buy and install a new battery.

• Satellite M30-951 - processor clocked at 600 MHz (it must be at 1500) - high energy saving

  Hello

  earlier this year, a company has changed the case of my laptop. Since that time on the laptop was very slow. I thought it has something to do with the software, but after a new installation, the problem was not solved.

  Now, I used severel programs to check the speed of the CPU. Programms all tell me that my CPU Speed is 600 MHz (it must be at 1500 MHz).

  The laptop is connectet to current alternative and energy-saving is high. I did a bios update and spent setting the CPU in the Bios of dynamics to high. But no sollution.

  Then I saw that my fan does not (at the beginning, or when I use Notepad). I thought that his damaged, but I tested it on another laptop and the fan works perfectly with 5V.

  Moreover no program shows me the temprature, so I think the sensor of temprature or anything else is failure, so that the fan does not work and the CPU is at each time at 600 MHz.

  Does anyone have an idea how I can fix this problem or I have to change?

  Thank you very much

  Concerning

  Nassim

  Seems you have tried almost everything that can be done now.
  And I agree with you that there could be something wrong with temperature sensor and this is why I advise you to go to an authorized service provider to verify if this is really the problem.

  Before you do, you could try if the programmable notebook hardware control (NHC) can display the temperature because it is a very good tool. But as you say, no other tool could do this job, I doubt that it can control it. But worth a try.