Portege M800 CssSvr.exe error on the output of the mode standby

Similar Questions

• Explorer.EXE error after the restoration of the ERD Commander

  Dell Inspiron B130

  Windows XP Service Pack 2

  Recently performed a HD format and new installation of XP SP2. After I installed all the drivers and others, I checked that the system was operating normally. After a few days of use, Windows Update downloaded Service Pack 3 and asked me to install. I started to install SP3, but at about 50%, the laptop battery is dead at Midway through the installation. I plugged the laptop on the power source and power. I restarted the laptop and XP started only a completely black screen and the white slider. No ALT + CTRL + DEL, desktop icons, etc.

  I rebooted the laptop of ERD Commander, ran the restore system and selected the first available Restore Point. Point of restoration chosen was recorded a few days before, and was the first recorded point after the clean installed XP. I rebooted the XP system. Wallpaper loaded with white cursor, but NO start menu or desktop icon. A message appears saying "Explorer.EXE Application error, press OK to exit the application" or something very similar. Did not write the error code, but can get if necessary. If I press the OK button (which is my only option), there is still no icons on the desktop or the start menu. Only the cursor. No access ALT + CTRL + DELETE or something like that.

  Thinking about completely wipe the system and reinstalls the operating system. Any suggestions before I jump in this solution?

  Explorer.EXE error after the Restore Point of ERD Commander. Dell Inspiron B130. Recently clean installed XP SP2 on laptop. Installation of SP3, to 50%, battery dies the laptop right in the middle of the installation of the SP3 update. Restarted, XP starts with black screen with cursor only. ERD restart order and restore XP to the last known good config (I choose point immediately after XP clean install). Reboot to XP. Now the wallpaper shows as well as the error message saying "Explorer.exe Application error, click OK to exit Explorer" dialog and then I can't access anything. Any ideas?

  Hello

  What is the full and exact error message?

  Step 1: Check if you are able to boot into safe mode without any problem. If you are able to boot into safe mode without any problems then try to perform the clean boot to safe mode. Also disconnect any external devices connected to the computer.

  Reference:
  To start the computer in safe mode
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  Step 2: If you are still having the same problem, then you can the steps at the bottom of the article.
  How do I recover from a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

• ESXi 5 managing network not automatically start after reboot, or when the output of the mode standby

  vSphere 5.

  ESXi5.

  HI all 5 ESXi installed on HP BL460c G7. HP C7000 Enclouser system connected to the NAC (switch HP series A5800) via the Module HP FlexFabric 10 Gbs. The server has 6 vmcins:

  (1) management network - 2 NIC (1 GB per nic)

  (2) vMotion Network - 2 NIC (1 GB per nic)

  (3) Vitual Machine networks - 2 NIC (2 GB per nic)

  (4) zFCP - 2 network cards (6 GB per nic)

  After you restart or when the output of the mode standby, the management network starts does not automatically, you need to restart manually from the console directly. Hypervisor ISO downloaded directly from the vmware Download Center and all the recommended HP drivers downloaded and installed from HP Download Center.

  OK, another thing you could try is this change that HP recommended for my situation. The CLI performs: esxcfg-module - s "heap_max = 20971520" be2net

  and reboot. The memory default chunk size is not large enough and will change to this size in the next version of the driver.

  Also, have you tried yet 5.0 U1? There are a lot of bugs in U1.

• Portege M800 - stop if I hold the grille left

  If keep my Toshiba Portege M800 by the section of the front left lower side, he sometimes stops...

  The power led (top left) is always on, as it is in mode 'sleep' but does not. The only way to start again is to hold the power button for several seconds, then restart

  Does anyone else have this problem? Is my laptop defective?

  Thank you

  Hello

  A friend of mine had the same problem with another laptop. If it holds the laptop or door to another place it completely freezes. :(
  He did send the laptop to an authorized service provider and they replaced the motherboard. A few days later he did return the laptop and everything was working fine again! :)

  So I think you should send it to an ASP too. If you n t know one, on the Toshiba site, you can search for the nearest:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good bye

• Portege M800: How to turn off the LED light of the multimedia and the touchpad?

  Hello

  I have Toshiba Portege M800.
  I want to know, how can I turn off the light of multimedia and the touchpad
  Thanks in advance

  Hello

  I m not M800 owner but I ve got an another Toshiba laptop and these LED lights I can turn market in the BIOS and in Toshiba HWSetup.
  The HWSetup is placed in Toshiba help optimize them and the settings are in the tab 'enlightenment '.

  See you soon

• AccelerometerSt.exe error on the computer Windows 10 brand new

  I have the same problem that many others have with the Application AccelerometerSt.exe error.   BUT, I have a brand new - 1 week old computer and it came with 10 windows already on it.  I have the HP Envy x 360.   How do you intend that to solve the problem.   If you uninstall and reinstall Windows 10, I'll need much more detailed information.   I don't know how to do this - which was the reason why I only watched computers with her already preinstalled.

  Hello

  Try the following.

  Open windows control panel, open programs and features, make a right click the entry for HP 3D DriveGuard and select uninstall.

  When this has completed, restart the laptop.

  When windows has reloaded, download and install the version of DriveGuard on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67280.exe

  Kind regards

  DP - K

• Windows Vista starts with white screen - dwm.exe and dllhost.exe errors on the hard drive.

  original title: freezing after login! ... disk hard dwm.exe and dllhost.exe errors. As usual load screen and then nothing can be used/open to all. Occasionally start opens and closes and nothing else beyond.

  Cannot use the laptop mode safe mode with networking. Have you tried to repair registry free of bugs and using Vista install with view to repair OS repair disk, but there are a lot of people having this problem different from this problem with dwm.exe dwm.exe or versions/varieties. This is is produced immediately after the download and installation of Microsoft Updates I might add.  Please can someone help?  Thank you very much... LiZ :)

  Never use Registry Repair programs.

  They can cause more harm than good.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Understand the Extras in Windows Vista and Windows Update info is at the link above.

   

  Remove the Vista updates; two ways to do this:

  1. a System Restore to before the updates:

  Click Start > programs > Accessories > system tools > System Restore > restore time/choose your own date > next

  If you use Norton, disable it before using the system restore.

  If it is impossible to enter the Normal Mode, do a Safe Mode system restore:

  Press F8 at the startup/power and the list of startup options, use THE ARROW key to select Safe mode > and then press ENTER.

  System restore steps according to the info above.

  Also:

  2. click on start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

  > then click the one that you don't want > uninstall will appear at the top > uninstall it.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

  > Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

  When you take a look at pending updates, you can either download/install them one at the time, namely the update causing you problems.

  > or if you do not need an individual > right-click on > UAC prompt > hide it

  See you soon.

  Mick Murphy - Microsoft partner

• Tablet Wacom nonfunctional after the awakening of the mode standby

  I have Windows 8,

  Dual core 2.8 ghz intel, 8 GB of ram.

  I use a Wacom Bamboo (ctl 471) splash tablet.

  I installed the latest windows drivers 8 Wacom.

  When my computer wakes from sleep mode, the Tablet no longer works.

  I have to restart the computer to make it work.

  That kind of defeats the whole purpose of the mode 'sleep'.

  Any ideas?

  Hi eingram,

  Thank you for choosing Windows 8 and for giving us the opportunity to help you.

  I understand that the tablet will not work after waking from sleep. I will try to help you with this.

  (1) did you make any changes before the show?

  (2) you receive an error message/code?

  Method 1: I would uninstall drivers and reinstall them.

  a. open the key Device Manager by pressing Windows + R and type Devmgmt.msc

  (b) display or touch drivers.

  c. Please, right click and try to uninstall the driver.

  d. restart the computer and the update.

  Run the troubleshooter of material and check.

  Method 2: Follow the steps to run the Troubleshooter:

  a. press Windows + C keys on your keyboard to show the charms.

  b. type troubleshooting, and then click solving problems under settings.

  c. now, type Hardware Troubleshooter in the search option.

  d. click convenience hardware store to run the troubleshooter.

  Please report if you are still having the problem. I will be happy to provide you with the additional options that you can use to get the problem resolved.

• L540 missing WiFi/BT after activation of the mode standby

  Hello

  I use L540 running Windows 8.1 64bits. After waking from sleep, my Intel(r) Dual Band Wireless-N 7260 does not work. Operating system detects the NIC, but Device Manager shows the exclamation point. Troubleshooting Auto does not work. There are two ways to fix this problem - stop and restart PC or device uninstallation/installation using Device Manager. All the drivers/firmware is up to date.

  Do you have an idea what to do?

  Hi Aleksandarm,

  Welcome to Lenovo Community!

  According to the request, we understand that you are facing problem with the Wifi does not work after wake up mode standby on your ThinkPad L540.

  Please check is the (allow the computer to turn off this device to save power) is checked, to proceed to the steps you have to go Device Manager expand network adapter and right click on Intel(r) Dual Band Wireless - N 7260 go to properties, click power management and change the setting.

  Can you please provide us with the Dual Band Wireless-N 7260 (R) driver version.

  Please let us know the results once you have completed the steps above.

  Best regards

  Agnes Kumar

• Unwanted automatic reactivation of the Mode standby mode when it is connected to the Internet

  I have a relatively new home office Pavilion model p6140F, product number NP192AA, version number software 93NAv6PrA2.  Factory installed operating system is Windows Vista Edition Home Premium, 64-bit, Service Pack 2.  I am connected to the internet via a cable modem.  I made energy-saving settings for automatic sleep mode sleep.  Quite often the computer comes out of fashion "sleep" on its own.  What is strange to me, is that when this happens and I click the Start button at bottom left of the screen or any buttons on the Quick Launch bar, nothing happens on the first click.  Only on the second click the computer is what I normally wait until it gets when clicking on the Start button or the quick launch of the first time button.  I tried an experiment by disconnecting the internet cable from the computer modem and the computer behaves as I expect.  He remains in the mode "Eve" from one day to the next day when I unplugged the internet overnight.  It looks like something 'out there' on the internet is somehow take control of the computer, do not let it go in the mode 'sleep' and play with use and function of the 'Start' buttons and the quick launch area.  At the very least, it's embarrassing, if not malicious.  Is occurring with other users?  Wouldn't be some 'normal' functioning of monitoring by HP, Microsoft, providers of security software that I have permission, or is this behavior that should not be expected.  Thanks for any direction on the techniques of 'analysis' on mine could give clues at the origin of this strange behavior.

  Bad Board.  Marking as resolved.

• My question is that I have a HP Slimline it will harm my computer just if I leave it on the mode "standby" 24/7 and

  I have a HP Slimline Pavilion model: s5120f, Prod: NP187AA, Windows Vista. My question is it will harm my office if I leave

  on mode "standby" 24/7 and the monitor configured to sleep approximately: 20 Minutes?

  It will not damage your computer to "sleep" 24/7 and wake up to the need.

• Win 7 x 64: No. WWAN after the resumption of the mode standby and Bluetooth turned off

  Hey guys,.

  I had this problem for a few weeks 1-2, after the exit of the mode ensures my WWAN - the Sony Ericsson 3507g - modem is invisible and my Bluetooth is disabled.

  WWAN: the light is off, there is no switch on the screen Fn + F5 and power off/on with the hardware switch does nothing either, after a reboot, that everything is back to normal again until you go back to sleep. A few days ago he suddenly perfectly well but when I had to restart, the problem is back.

  Bluetooth: the adapter is always disabled after sleep and sometimes after a reboot, I can not find a model to know when this happens exactly... but I have since my WWAN modem is upward I can't help but wonder if it has the same cause...

  I already did a complete new installation of Windows 7 Home Premium x 64 today and I'm under the latest Vista drivers, because those who do not work with the Ericsson Wireless Manager Windows 7, they ran flawlessly for a few weeks, so that they should not be the problem...

  BOT of the above issues is dealbreakers for me because I'm using WWAN all the time and I use a Bluetooth mouse... then... Please help me ;-)

  Thank you in advance,

  Stefan

  I think I found the culprit: the last time I had this problem I didn't know what was the reason.

  After that the above post I got it works fine until recently it suddenly reappeared without having done me anything (Finally, I've done something, but I couldn't understand that).

  I installed a few games, but nothing about the wwan adapter.

  I also had the same problem to launch a vanilla Ubuntu 9.10 x 64.

  Finally it dawned on me that, just as the problem the first time, I had also installed Ubuntu. I think that something about the way that Ubuntu handles the umts modem makes it behave this way.

  This time (since I seen Ubuntu as the reason yet and I couldn't understand anything more), I opened the Thinkpad and looked for clues as to why this was happening - loose cables and all that - but nothing was wrong. I also disconnected the small backup battery for a few minutes to reset all the BIOS (except the part that is not volatile of course) - who probably had the same effect as turn off/turn on the modem I/O on-screen that solved the problem last time.

  Then, I rebooted, entered the BIOS, responsible for the default installation with F9 and it suited my needs. Since then he has worked flawlessly again...

  I'm not sure that Ubuntu bad, but it's the only logical explanation, and I think that's the reason why some mistreatment of the modem which required a "reset" on the base material, it is why a complete reinstallation of Windows did not do one thing...

  For now, I can just advise all users T500 WWAN to avoid Linux - Ubuntu, especially - at least until understand you what causes the strange behavior.

  Just my 50 ct other people with the same problem so some ideas on how to solve this problem.

  Stefan

• Explorer.exe error in the ntdll.dll module

  Event type: error
  Event source: app error
  Event category: no
  Event ID: 1000
  Date: 18/10/2009
  Time: 17:28
  User: n/a
  Computer: CROSSROADS
  Description:
  Failing application explorer.exe, version 6.0.2900.5512, failed module ntdll.dll, version 5.1.2600.5755, address failure 0x000101b3.

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
  Data:
  0000: 41 70 70 6 c 69 63 61 74 Applicat
  0008: 69 6th 6f 20 46 61 69 6 c ion Fail
  0010: 75 72 65 20 20 65 78 70 exp ure
  0018: 6 c 6f 72 65 72 2 65 78 lorer.ex
  0020: 65 20 36 2 2 30 32 39 e 6.0.29
  0028:30 30 2 35 35 31 32 20 00.5512
  0030: 69 6 20 74 64 6 c 6 c in ntdll 6f
  0038: 2e 64 6 c 6 c 20 35 2e 31 .dll 5.1
  0040: 2e 32 36 30 30 2e 35 37.2600.57
  0048: 35 35 20 61 74 20 6f 66 55 to of
  0050: 66 73 65 74 20 30 30 30 000 fset
  0058: 31 30 31 62 33 0a b 101, 3 0D...

  also get the explorer.exe in comctl32.dll errors, gdi32.dll, kernel32.dll, shell32.dll in successive attempts to restart.

  PSHersh,
  Thanks for posting on the Microsoft answers Forum.  The first thing that I would suggest you do is run the System File Checker.  The link below will provide information on this tool.  You want to run the "SFC/scannow" option  You will need your XP CD for this tool in case we need to correct all files.
  http://support.Microsoft.com/kb/310747

  Let us know the results. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• A lot of EXE errors during the execution of the tasks

  When I try and do any what - restoration of the IE system, etc. - it is said that C:\WINDOWS\system32\rundll.exe APPLICATION NOT FOUND - a window opens and asks me what program I want to run it since... I don't know - what is happening on all that is needed. EXE

  Cannot download same adobe reader, etc.   I get this error when you try to use both control panel - any application.    Rundll.exe is located in the correct folder... but the icon is weird - not the little box that usually has been there.    protection against all viruses has been executed and validated.

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Try to perform the clean boot and check if it helps:
  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  Method 2:
  Try the running System File Checker and see if it helps:
  http://support.Microsoft.com/kb/310747

  It will be useful.

• IAStorIcon.exe error in the Windows Vista-based computer.

  Original title: my computer error.

  My computer error Massage is:

  IAStorIcon.exe

  Problem event name: CLR20r3

  Signature of the problem 01: iastoricon.exe

  Signature of the problem 02: 10.1.0.1008

  Signature of the problem 03: 4cd508b4

  Signature of the problem 04: mscorlib

  Signature of the problem 05: 2.0.0.0

  Signature of the 06 problem: 4ef6c7cc

  Signature of the 07:2539 problem

  Signature of the 08:0 problem

  Signature of the problem 09: System.IO.FileNotFoundException

  Hi Ariane,.

  1. when exactly you receive this error message?

  2 did you change on your computer before this problem?

  IAStorIcon.exe is part of the IAStorIcon developed by Intel Corporation. The program is linked to the Intel technology to recover Rapid (part of the Intel Matrix storage technology).

  You can follow the steps in this link & check if the problem persists:

  IAstorIcon error at startup

  
  Note: software use of third parties, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope the helps of information.