PortFast to non manageable switch

Similar Questions

• VLANS with Cisco ASA 5505 and non-Cisco switch

  I have an ASA5505 and a switch Netgear GSM7224 L2 that I try to use together.  I can't grasp how VLANs (or at least how they should be put in place).  When configuring my VLAN on the ASA5505 it seems simple enough, but then on my switch, I thought I'd create just the same VLAN numbers that I used on the SAA and then add the ports that I wanted to use for each VLAN.

  Currently on my ASA, I have the following VLAN configured...

  outside - vlan11 - Port 0/0

  inside - vlan1 - Port 0/1

  dmz_ftp - vlan21 - Port 0/2

  Port of Corp - vlan31 - 0/3

  I need to do the same thing on my switch as well...  On my way, I'm a little confused as to how I need to configure the VLAN.  Below is the screenshot of web GUI...

  

  Note: Normally you can now change the VLAN ID (red), but in this case the default vlan (vlan id 1) may not be changed or deleted, you can does not change its settings.

  Tagged (green), Untagged (purple) and Autodetect (yellow) you must select at least 1.  I'm not sure how to in one place to tell my inner vlan (vlan1).

  I want VLAN1 ports 1-8 on my Netgear switch used alone to talk to interface/0/1 on the ASA5505 port.  I don't want to NOT port 9-24 able to talk to ports 1-8 on the Netgear switch ports OR 0/0, 0/2 - 0 / 7 on the Cisco ASA 5505.

  So, how can I configure my inner Vlan1 on ports 1-8 on the switch?  Do mark, UNTAG, autodetect them?  What about tours?  I've been a bit the impression that I would set up my VLAN on both devices, then trunk port 1 and dedicate this port on both devices to nothing other than the sheath and the security of vlan would then take the packages where they need to go.  Is this the wrong logic?

  Hi Arvo,

  If the port of the ASA is just part of a single VLAN (i.e. e0/0 single door 11 VLAN), this is called an access port. If the port of the ASA had to carry several VLANs, it would constitute a Trunk port.

  To access ports (VLAN unique), you must set the switch corresponding to be unidentified for port this VLAN individual. If you decide to configure a trunk port, then the port of the switch must be set for labelling for each of VLAN who win the trunk.

  For example, ASA I have:

  interface Ethernet0/1
  switchport access vlan 20
  !
  interface Vlan20
  nameif inside
  security-level 100
  ip address 192.168.100.254 255.255.255.0
  

  With the above configuration, the configuration of the switch would look like this (assuming the e0/1 port of the SAA is connected to 0/1 on the switch):

  VLAN 20 - 0/1 = untagged

  If instead you use a trunk port, the config would look like this:

  interface Ethernet0/0
  switchport trunk allowed vlan 10,20
  switchport mode trunk
  !
  interface Vlan10
  nameif outside
  security-level 0
  ip address dhcp setroute
  !
  interface Vlan20
  nameif inside
  security-level 100
  ip address 192.168.100.254 255.255.255.0
  

  Assuming that the ASA e0/0 port is connected to 0/1 on the switch):

  VLAN 10 - 0/1 = tagged
  VLAN 20 - 0/1 = tagged
  

  Hope that helps.

  -Mike

• What switch do you recommend

  Hello

  Brief description of our environment...

  x 1 poweredge R720 with x 4 network ports for iSCSI
  x 2 poweregde R710 with x 4 network ports for iSCSI
  x 1 poweregde R610 with x 2 network ports for iSCSI

  x 2 PS6100E EQL
  x 2 PS4100E EQL
  x 2 PS6000 EQL
  X 4 PS5000 EQL

  Everything is distributed evenly between two floors of the building by using SyncRep and regular replication on the EQL boxes and using a VMware HA and DRS cluster on hosts.
  Physically separate networks for iSCSI network and production.

  We use 5448 powerconnect on the iSCSI network switches. One PC5448 for each floor and they are connected with x 4 fiber LACP trunk link.

  I know that these switches have to be replaced, but what? PC6248, PC7048 or Force10? Perhaps even another manufacturer? If so which model? The price IS a decisive factor, I don't have the budget for expensive stuff

  Check the support matrix Equallogic to get an idea of what switches are validated and supported / recommended. It is not limited only the Dell switches (Cisco, Juniper and Brocade options listed there).

  First, you'll want to upgrade to double switches on each floor and LACP together. You can stack them, but this has the drawback that if ever you want to / need to upgrade the firmware of the switch in one or both of the rooms, you'll need 100% service interruptions in this room.

  In my next part I'll stick to switches Dell since it is a Dell message board.

  I would skip the PC6200 series unless your budget can not install a switch better. The 6200 is a decent switch, but it's on its way out (this can be seen by the fact that Dell has not updated the firmware on the switch since the 3.3 series (all 7 k and higher switches are now on a firmware 5.x).) The Force10 S25 series is better than this PC7024 a switch, but if you plan to switch to 10 GB at some point, you may consider a pair of 8132 s PowerConnect in each room. The non - F version uses RJ45 ports that can make 1Gbit and 10 GB, then you can use to start just the current units of EQL, but new units could be 10Gbit units. You want to get the QSFP + optional modules for each switch and 2 wires for each pair, so you can use these 2 40Gbit LACP ports switches set in each room.

  If you want to use a LACP between the 2 rooms consisting of two switches, you have a more difficult choice to make; stack the switches (with the disadvantage that I mentioned above), or upgrade to Force10 S4820s that these offer the possibility to make a channel of port on 2 non-Stack switches (PowerConnect firmware does not offer this).

  Cisco and Brocade offer similar characteristics (to execute a LACP on 2 switches non-Stack), but I do not know what exact firmware and/or switches that would offer.

• SG200 or SG100 switches of the series?

  Hello

  I am helping a company data selection switch and VoIP for a small company of about 40 users who is penetrating new spaces and adding VoIP.

  The subnets of voice and data will be routed to the other.  No VLAN or QoS are necessary according to the VoIP provider.

  They need ports gigabit PoE 22 for phones and no PoE ports of 40 +.

  The part-time computer scientist on the spot has no experience in the management of the switches.  So, they think about the use of six switches of SG100D - 08 p unmanaged for the PoE ports with all what SG100 switch to non PoE ports.  However, it seems that both switches of series SG200 (SG200 - 50 p and SG-200-50 or SG200-26), would be easy to set up for this purpose and require little management.  They have most of the equipment rack mounting.  It seems that SG200 switches would solve what could be a mess of this and son with six SG100D - 08 p of

  I understand that little, if any requirements for a non - PoE switch SG200-xx. Is this correct?

  Can someone please comment on how the SG200-xxP switches are easy to use and advice or suggestions?

  Thank you

  Caseranch

  Hi Caseranch, please consider that SG200 switches are not POE on each port only 1/2 of the ports. At a switch 48 Port POE 24 ports. I know this should meet your requirement, but for the future expansion of POE, another POE switch.

  You're right, in this sense, the SG200 needs very little to zero configuration. The only thing I recommend is if you buy a switch to manage, upgrade to the new firmware, factory reset the device and then install and connect things for her. This should be sufficient based on the way you describe things.

  -Tom
  Please mark replied messages useful

• Windows Server 2012R2 - network location awareness continues to change the public domain after rebooting

  I also have this problem but I have domain controllers that are NOT part of this Hyper-V host.  If I restart the network location awareness (which also restarts the network list Service) it goes back to the field as it should.  Now when I reboot this server it will be once more put the interface / network to the public even if this Hyper-V server has been successfully joined to the domain with a static IP address.

  Now for clarification.  This Hyper-V server is NOT yet configured virtual.  The only thing that has been set up is a NIC team with two cards on Board (LAN 3 & 4 ports) and two additional network cards four port card (ports 3 & 4).  Local network connection is dedicated to LAN Port No. 1.  We also have a dedicated of the IMM port for access to the Strip.

  The ONLY time I can get this server to restart and STAY in the 'Domain' location is now if I have the PORTFAST enabled on the switch port to which it is connected.  Yes, we use STP here in our company.  This is not the first time that I had to do this, but it seems not just as a colleague claims that he didn't need to do and its technology Hyper-V server restarts fine.  I him have had check it out and he sees no difference between its servers and mine.  Still mine restarts always in the "public" unless I have active portfast.  Any thoughts?

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• HP Pavilion dv6 entertainment: Cortana not see internet wifi (in English and Italian)

  I'm Italian,

  I've recently updated to windows 7 to 10.

  I have some questions:

  (1) why Cortana not see my wifi connection? Ditto Microsoft Edge.
  But the connection goes because I am not here.

  (2) why can't I activate windows 10, after update to 10 windows 7home Premium.
  -----------------------------------------------------------
  IO sono italiano.

  Ho aggiornato al windows 7 10 recently.

  Ho delle request:

  (1) boom Cortana non vede internet outdo mia? Lo stesso vale per Microsoft Edge.
  The hotel will not sari since that.

  (2) perched non posso switch windows 10 dopo aggiornamento di windows 7 Home Premium al 10?

  Hi @alienogiocoso,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dv6 Notebook and questions with Cortana. Here is a link to solve problems with Cortana.

  I hope this helps.

  Thank you.

• question from newb on 6100 fabrics

  Hey,.

  What is the difference between the 6100's and nexus switches?

  I look at vids on UCS and it seems that the networking and the fabric are on the 6100 6100 modules are s of the nexus switch? They are completely serperate devices this site to the South the Nxs switches?

  Can someone give a brief explanation?

  Brent, the interconnections of fabric UCS (FI) are the point of grouping all the chassis connection blade & rack UCS servers.  In addition, the FI to run the software of management of the UCS.  FIS are a separate device.  They have just the same physical appearance as the nexus 5K, but they are distinct & unique devices.

  UCS can uplink in your Distribution, or even of the basic network switches.  It could very well be a pair of Nexus, Nexus 7 K, Cat6K 5Ks or any which non-Cisco switch.

  Here's how common a UCS deployment would look like & sit in a network running continuous.

  

  Here is an another digram showing the UCS uplink for both SAN and LAN Ethernet fabrics.

  

  HTH,

  Robert

• Implementation of VLAN / QoS for VOIP on RV180

  I posted earlier about setting up VLAN / QoS for VOIP on the SG200-18 (see: https://supportforums.cisco.com/discussion/12193666/setting-vlan-and-qos...).

  I did go ahead and buy the RV180. I connected to SG200-18.

  I wish to proceed with the implementation of VLAN / QoS on the RV180 so my phone (Grandstream VOIP wireless phone) VOIP is on its own VLAN separate from the rest of the network, so make sure that all QoS settings are optimized to give the first priority of VOIP network telephone.

  Currently I still have the VOIP phone connected to SG200-18 as stated in the previous post.

  Here are my questions:

  1 should I leave the VOIP phone connected to the SG200-18 and config all the VLANS, VLANS and VLAN Switch voice settings down to the VOIP phone, or should I plugged the phone VOIP in the RV180? Which would give me better performance and easier to do?

  2. How can I place the VOIP phone on its own VIRTUAL LAN, in addition to optimizing QoS settings so it gets a top priority for the network?

  3. I currently have set VOIP telephone in order to reserve a DHCP address in the 192.168.x range. When you move to the VLAN, should I set the DHCP reservation and/or my firewall settings (I through the firewall as well)

  4. I also get a beta-test VOIP Grandstream office phone. Time of its installation, what I have to plug directly into the RV180 or the SG200-18, and I have to put it on the same VLAN as the phone VOIP without wire Grandstream or VLAN different? It also supports PoE, but the RV180 or SG200-18 model I does not work. If I use an external power supply, connect each device will be OK or might that it became fried?

  Thank you!

  Hello

  1 should I leave the VOIP phone connected to the SG200-18 and config all the VLANS, VLANS and VLAN Switch voice settings down to the VOIP phone, or should I plugged the phone VOIP in the RV180? Which would give me better performance and easier to do?

  It will not be much difference between being on the switch or on the router, so it is for the most part to the simplicity of configuration performance.  If you plug the phone directly on the router, you will really not disturb trunking VLAN or none of this switch.

  This is really what is more convenient, but if you are able to plug into the RV directly I wouldn't worry QoS on the switch.

  So let's talk about implementation of the RV180.

  First go to network > LAN > belonging to a VLAN.  Enable VLANs, and add a new VLAN for voice (most people use 100 for voice for a reason, but it does not matter).  You will take care to set the port that the phone is plugged in not tagged to the new voice VLAN, and you can exclude the data VLAN of the port.

  Then go to several VIRTUAL local network subnets and configure the address range for it configuration DHCP / new subnet (for example 192.168.100.0) If you do not want to use it (makes things a bit easier)

  Finally, to enable QoS on the RV go to QoS > QoS WAN profiles.  Activate the WAN QoS, make sure that it is set to the priority mode and add a new entry to the table.  You can name it anything you want (I used VoiP), then set it high priority.

  Then go down on the link profile page and add a new entry here. Select the profile you just created in the drop-down menu, set the service to one, select traffic selector VLAN and make sure the drop-down menu for VLAN is the VoIP VLAN.

  At this point, we have a configuration where the voice traffic (or basically anything on the VLAN voice) will have priority when it comes out the WAN interface.

  3. I currently have set VOIP telephone in order to reserve a DHCP address in the 192.168.x range. When you move to the VLAN, should I set the DHCP reservation and/or my firewall settings (I through the firewall as well)

  The second VIRTUAL LAN should have a configuration of different subnet for him, because I spoke up.  During this process you will place the DHCP server for the new VLAN as well.  You can adjust your reservations for the phones, but it does not really matter what IP they get, since we are prioritizing voice any VLAN, so you don't have set up a reserve, unless you really want to.

  4. the Grandstream phone.

  I would put the Grandstream (and all the other VoIP phones that you could get) in the voice VLAN so that he would get the same priority treatment.  At this point with multiple devices, you can indeed install a trunk to the switch (VLAN normal unidentified and voice VLAN Tag) and configure the ports to the voice VLAN for these phones.  Who will ensure that the switch gives priority to the traffic of voice, even if it is probably not as important in their own country on the WAN.

  Regarding the PoE device connected to a non PoE switch or a router, there will be no problems.  I'm guessing that the phone also comes with an AC adapter.  It will not feed this power in the thread just because it's PoE, it's pretty much a one-way circuit.

  Hope that helps,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• Cisco NAC offers Support

  Hello

  I have some question about Cisco NAC and don't know if it is able to support:

  1. can you packets qos to NAC honor/confidence when it is configured for inband/off band?

  2. for the creation of the lobby admin on local accounts management comments (using the own access device); cisco nac appliance does support

  the lobby admin via acs/external db authentication? If this isn't the case, adding a comment server would reach it?

  3 - is not cisco NAC appliance support wireless controller and the mixture of cisco/non-cisco switches? If so, if the switch supports snmp mib mac-notification/link/link down; would this be enough?

  4 is Cisco NAC comes with a predefined set of rules AV to verify that all AV support is running for the posture check (example if NAC supports 100 produced different viruses; can he check all 100 different product that can be installed on a PC for control of posture). An example of this would be hotel / that there are people of different products installed antivirus trying to access the network and the antivirus must run and installed and updated to access network). I know that the pre-confgiured default rule can check for installation/setting however not sure on the status of service / application running.

  Thank you.

  Hello

  For VGW configurations, you must have in separate subnets. For RIP, they can be in the same subnet without problem.

  HTH,

  Faisal

  --

  If you find this article useful, please note so that others can easily find the answer

• interface web cisco ip phone from the computer LAN

  Hello

  On the uc540 the DATA VLAN is en 192.168.10.0 as the VLAN DATA it is en en 10.1.1.0, I want to access them from the local network the computer the my client who is en 192.168.0.0 to web interfaces of the cisco ip phone so by going to http://10.1.1.x without needing to modifier already exists, how can this be done? I have available in my not to a manageable switch that would allow me to integrate the lan that does not exist in the DATA VLAN of the CPU.

  Thanks for advance

  Hello

  The voice VLAN 10.1.1.0 is not routed in your network.

  Namely that workstations do not know that there is, and this due to the fact that their router default doesn't know not router network.

  Here's how to fix that little problem of routing:

  1 / if the default router for the positions in the VLAN data isn't the UC 500, just to add a static route in this router with the sub network 10.1.1.0 and address of next hop (IP address of the router that helps you achieve this subnet).

  For example: If the default router is a Cisco router, it is in the VLAN data with the UC500 and the UC500a as the IP address 192.168.0.1.

  conf term

  !

  Route IP 10.1.1.0 255.255.255.0 192.168.0.1

  !

  end

  2 / if we can't change this router by default, we must add a path in given work stations of the VLAN.

  In a post Windows you do that in a CMD window with the ROUTE ADD command

  c:\>route add 10.1.1.0 mask 255.255.255.0 192.168.0.1

  and you can check your local routing table with the command

  c:\>route print

  If you want that this road remains in positions of work even after a reboot, use option-p of the route command added

  c:\>route add 10.1.1.0 mask 255.255.255.0 192.168.0.1 Pei

  Control the Access-list!  : Of course, after having solved the problems of routing, assure you that there is not an access list that blocks traffic

  FINISH POUR a bit of security.  Allow access to the VLAN voice is not a good practice!

  As long as possible, to avoid to make the voice VLAN too accessible from anywhere. Therefore, a good practice is to not allow the VLAN data access to the VLAN voice.

  Patrick

• authentication dot1x some problom

  Hello

  helleo

  WO have a problom to dot1x authentication,

  When I enter the configuration of configuration of dot1x in the interface, interface to authenticate user in State of err - disable

  Here is the configuration of the interface
  interface FastEthernet0/45

  switchport access vlan 21

  switchport mode access

  the host-mode multi-auth authentication

  Auto control of the port of authentication

  MAB eap

  dot1x EAP both

  dot1x quiet-period of waiting 3

  dot1x tx-period 5

  spanning tree portfast

  Or authenticating switch failed newspaper

  n 4 16:52:16.381: % AUTHMGR-7-FAILOVER: failover "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.381: % AUTHMGR-5-START: start "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % MAB-5-FAIL: failure of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-RESULT: authentication result 'no response' of 'mab' for the customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-FAILOVER: failover "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-NOMOREMETHODS: exhausted all methods of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-5-FAIL: failed authorization for customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:17.165: % AUTHMGR-5-START: start "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % DOT1X-5-SUCCESS: authentication successful for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID

  June 4, 16:53:21.376: % AUTHMGR-7-RESULT: result of the authentication 'success' of 'dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: cannot add the address on Fa0/45 AuditSessionID 0A51F11D000000266273D33D 2c41.380f.f187

  June 4, 16:53:21.376: % AUTHMGR-5-SECURITY_VIOLATION: security breach on interface FastEthernet0/45, new address MAC (2c41.380f.f187) is considered. AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % PM-4-ERR_DISABLE: error in security breach detected on Fa0/45, putting the Fa0/45 in State of err - disable

  June 4, 16:53:22.400: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/45, state changed to surviver 4 16:52:16.381: % AUTHMGR-7-FAILOVER: failover "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.381: % AUTHMGR-5-START: start "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % MAB-5-FAIL: failure of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-RESULT: authentication result 'no response' of 'mab' for the customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-FAILOVER: failover "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-NOMOREMETHODS: exhausted all methods of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-5-FAIL: failed authorization for customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:17.165: % AUTHMGR-5-START: start "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % DOT1X-5-SUCCESS: authentication successful for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID
  June 4, 16:53:21.376: % AUTHMGR-7-RESULT: result of the authentication 'success' of 'dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: cannot add the address on Fa0/45 AuditSessionID 0A51F11D000000266273D33D 2c41.380f.f187
  June 4, 16:53:21.376: % AUTHMGR-5-SECURITY_VIOLATION: security breach on interface FastEthernet0/45, new address MAC (2c41.380f.f187) is considered. AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % PM-4-ERR_DISABLE: error in security breach detected on Fa0/45, putting the Fa0/45 in State of err - disable
  June 4, 16:53:22.400: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/45, changed state down

  Looks like your scenario made to match a known defect

  CSCti69845 voilation took place after the success of fashion multi-auth auth

  Workaround

  Configure a vlan VoIP Multi-auth port (or)

  Address / solved in paragraph 12.2 (55) SE01

  Jatin kone
  -Does the rate of useful messages-

• How to view the vswitch on ESXI 6.0 mac address table?

  Hello!

  Is there any medium vswitch to view for all (or special) mac address table CLI?

  It is very useful in troubleshooting scenarios, but I can't find how to do it.

  Thanks in advance!

  ESXi virtual switches are not manageable switches.

  You can query to switch using the vSphere API, see this - http://www.virtuallyghetto.com/2011/05/how-to-query-for-macs-on-internal.html

  Thank you

  Hentzien

  Virtual Admin

• Configurazione san

  Hello to all,

  I like to start a my configurare he mio ambiente virtuale ho some dubbio da clarify, per I quali non trovo risposta sui vari manuali.

  Ambiente e composto da 3 host substitutes, 1 iscsi san HP P4000 (1 coppia di cluster storage), 2 switch HP procurve its alla san, 1 qnap by backup it.

  Dubbio 1: stare of the san sta in una rete is dedicated, how separata dalla lan azienda, my deve anche su una class di separata sulla stessa o IP class di IP? IO pensavo di separarle, nel senso che lan business e configurata come 192.168.1.x mentre san sara 192.168.2.x, my mi è venuto he dubbio nella configurazione del management group della san mi viene required pole address del server di posta per per dei messaggi di attention, e questo, ovviamente sta nell'altra rete, e ROMA non avere accesso al gateway theory an internet is the separo dalla dalla san lan , quindi come fa a mandarmi mail?

  Dubbio 2: sono a po' sull'architettura della san confuso. Each 2 nodi P4000 ha due dei is iSCSI, che mettere I like team per aumentare Velocità e tolerance AI guasti, my 2910al di HP non fanno switch switch port trunking due tra gli. Devo quindi collegare due door del nodo 1 Hello pass 1 to the door del nodo 2 Hello switch 2 per poter abilitare sugli switch it trunking, oppure connect per ogni nodo una porta per switch e faccio it grouping delle door solo sugli storage?

  By ora mi fermo who took the request delle ora banalità my of cominciando sto.

  Grazie

  "parlando Stai con me? (case No.)

  Comunque, the iscsi rete con indirizzamento e più che altro una questioned "igienica" FAT32: e vero che sono separated, reti my nel caso uno prima o poi mistakes a rete connettere UN apparato di, scatenare Source ip e dare drowning Hello storage e an attimo. Oltre al fatto che più e easy al volo di rete quale other if sta guardando parlando IP.

  The configurazione, mainly invito a studiarsi he documento di integrazione ufficiale running VMware vSphere 4 HP LeftHand P4000 SAN Solutions, e relativo an ESX 4 my will benissimo anche by 5. Leggi inoltre HP StorageWorks P4000 SAN Solution user guide.

  Dai documenti, secondo he specie, already varies configurazioni by rates collage anche senza fine it cross-stack etherchannel (ovvero i fare aggregando trunk door places switch differneti, my trovi questa fruit sui procurve a partire dai 5000 year chassis, roba da ricchi...).

  Fondamentalmente, having had to pass, you can due cose fare:

  -Adaptive Load Balancing, set the nic due not line any switch sugli configurazione e active/passive

  -Link Aggregation dynamic Mode, set the nic in active/active my queste must be mass obviously knew a single switch to non hai he cross-stack, quindi non previene break dello

  In realtà, per come funziona he P4000, sarai m'immagino con due nodi networked Raid 1 e quindi it failover lo fai tra I due nodi. Failover Manager he serve solo by manage, quorum it, dato che una struttura P4000 deve sempre work number dispari di sistemi con.

  Ciao,.

  Luca.

• When you print a book in PDF, bookmark definitions are not saved

  I remember seeing another post on this subject and I can't find it now, but none of the solutions mentioned he worked for me, so this is:

  I'm working on a migrated book of FM 9 to 11 of the FM, and when I print to PDF, I specify bookmarks I want to display in the tab favourites of the dialog Configuration of PDF for the selected files . The PDF file prints fine, but when I want to print the book once again, FM does not remember my settings, forcing me to set bookmarks from scratch every time. This has proved quite painful because I'm working with an old book in which the styles are not intiutive, so try to remember all of them each time is not the best of pleasure. When I print a single file in the book, the settings are saved correctly.

  In the previous post, I remember reading that it was a bug in FM and try the following suggested solutions (of which none worked): switch mode structured; Save the position desired in a single file in the book, printing the document and then print the book (had to train FM Recalling settings for the whole book); except the right to book after it prints; Select all the files in the book and record in PDF format, as opposed to the selection of the book, and then file > Save as PDF.

  I would be happy to know if anyone has any ideas or if Adobe is planning to release a patch for this problem.

  It is my understanding that FrameMaker uses the setting stored in the first document in the book when creating a PDF of a book. Then, open the first file in the book and make a PDF, defining your bookmarks you want for the whole book. Then, create the PDF of the book. Check the settings before clicking Print to make sure that they are what you want. You may need to make some changes, but to remember them the next time.

  I work with FM 9, so this may not be relevant for FM11. I felt it necessary to open the PDF Setup dialog box every time I make a PDF of a book and click on save/OK/whatever, to make sure that the bookmarks are created correctly. The settings are still correct, no change is necessary; but I think it is necessary to open the dialog box and close it to get updated bookmarks indented correctly in the PDF file. It may have been fixed in FM11.

  Van

• Ho fatto non trovo più pasticci he mio number di series by willing e switch Creative Cloud, come posso fare?

  Ho fatto non trovo più pasticci he mio number di series by willing e switch Creative Cloud, come posso fare?

  !

  creating cloud does not have a serial number.  It uses your adobe id.

  Download the creative cloud desktop application (after signing with your adobe ID), apps download Adobe Creative Cloud | CC free trial Adobe

  and use the desktop application to install your adobe creative programs of cloud.

  If you already have the cc desktop application and you will need to update your adobe id, connect, disconnect | Creative desktop application Cloud