Possible to enable link aggregation

Similar Questions

• What is p2-1124 support hp virtualization? Is it possible to enable it in the BIOS?

  What is p2-1124 support hp virtualization?  Is it possible to enable it in the BIOS?

  Hello

  Processors AMD Zacate are supposed to support AMD - V, with a few exceptions.

  Press the ESC key to power up and go to Configuration of the computer (f10).  Come on the subjects of security and the security of the system and search for virtualization.

  What operating system do you use?

• A group of link aggregated traffic mirroring

  Hello. I would like to mirror traffic entry and exit of a group of aggregation of link on my Dell PowerConnect 7024. By looking at the http under switching configuration page > Ports > traffic Mirroring > Port Mirroring > add, it doesn't seem to be an option for traffic a single port and not a link aggregated mirror group.

  Can someone help me to check if this is doable? If so, how?

  Your results are correct. Associate connection ports are not able to participate in the port mirroring.

• Router Cisco Small business with the functionality of the link aggregation

  Hi all!

  can someone tell me if there is a router from Cisco Small business with the functionality of the link aggregation? (I want to connect two 4 Mbps SDSL for flow)  The RV082 can do?

  Best regards

  You would need a RV016, who takes in charge up to 7 WAN ports. RV082 has only two WAN ports.

• VLAN Trunking, Link Aggregation Teaming e

  Hello to all,

  avrei need some delucidazione in merito ad una configurazione di vsphere tipo di.

  VI spiego in brief:

  2 vSphere host (host a host B e) con Nic 4 x host

  1 Swicth (by manage Vlan [LAN, WAN, DMZ, vMotion, FT, iSCSI, etc...])

  UNA configurazione base pensavo di implementare e configurazione di che a vSwicth0 con 4 Nic teamwork by every host.

  1 configurated it grouping schede di 4, sul mio spend devo configurare Illinois Link Aggregation o mi not serve? (Su Che HP e called trunk mi pare) in terms static pole e Unico supportato da vmware. IO ho noticed no configurando sullo switch funziona tutto e nulla che to provo a uno dei 2 cavi dictionary alla volta no capacity it marked.

  In più is configurated the vlan lato vmware e lato switch it tutto funziona a meraviglia.

  Ho cercato della menus in merito e mi sono imbattuto knew menus che strategies come collegare una a nodo con ESX 2 schede di rete grouping known uno switch HP 1820 - 24G switch trunk spiega di configurare lato Dove he terms static e change policy Exceptions led on the way teamwork based on hashing IP!

  Ho seguito guida (penso alla lettera!) my con mi ritrovo a problema e cioè che non raggiungo più he nodo ESX... create Reed is raggiungo all the macchine all'interno delle vlan!

  Part menus seguita indicarmi could be wrong something particular? Qual'e un'approccio by una configurazione del genere?

  Grazie!

  Ciao,.

  He port group management che ESXi default crea sommergibili durante ha UN override sulle di teaming dello switch che lo contains rules, pertanto is configuri ip hash sullo switch devi premurarti di farlo Reed dichiaratamente anche sul port group, altrimenti lo lost cosi come indichi! By Miss instradamento e momentaneamente entrare ESXi stacca chest he oppure altre tre at door

  By the configurazione, funziona tutto anche senza trunk perch it grouping nativo port id che fa e agli switch, solo devi overlooks VMware verificare che gli convenctions delle tabelle di ARP siano veloci, o nel caso di più presenti, che sia abilitato switch it quick dello tree covering weight, my con i modelli HP come he tuo o superiore usually queste cose funziona nativamente.

  Ciao,.

  Luca.

• Backflip: Is it possible to share links to social networking sites from the browser?

  Hi all. I was playing with my Backflip and that most of the time (apart from some odd questions every now and again). I love how I can post updates from a single blow to all my social networks that I have linked to my Motoblur account. It is quite convenient. I did something similar on my computer browser for a while with the help of an add-on called Yoono. Although one thing I can make sure I did not quite understand yet how can I go on the sharing of links on all of my accounts of social network at the same time? Is it still possible to do so directly, or do I have to use the sharing links on individual pages or copy the link and put in an update? Yoono offers a unique button 'share' which will lead the URL I'm at, capture images of the page, I would add a little descriptive text and then send it to networks no matter what I choose in a single process. It saves time by not requiring no me click every button share for each network and add descriptions for everything. Just click once and it goes to all. In the same way that status updates the work of Motoblur. Given that social network accounts are already synchronized with our phones, I was hoping there would be something like that where I could share a link from the browser or RSS reader app and post the link to all my accounts in a single operation without welding. So are there currently such a thing, or what I have to use a workaround? Thank you!

  Download free browser dolphin of the market app. When using it just click the menu button and it gives options for sharing things on different sites.

• What are the bare minimum commands to get a stack of PC6825 3 - switch with inter switch Link Aggregation?

  I am brand new to PowerConnect switches, even though I am familiar with the concepts of VLANS, aggregation of links and spanning tree.

  I am on a deadline to get some new ones installed 6248 in our baskets and get them functioning as a stack. What are the bare minimum commands for:

  • Three switches in a stack (master/Eve/member)
  • 2 ports grouped between each (total redundancy) switch with loops WITHOUT switching

  All the switches are running firmware v3.3.9.1 (January 2014).

  Thank you

  The range of interface Ethernet 1/g1-1 / g2 allows you to select the ports you want in the channel of the port. Page 293

  Channel-group 1 Auto mode to create 440 lacp lag page

  Select the Group of channels with interface port-channel 1

  Switchport page 601 in trunk mode

  Switchport trunk allowed vlan [VLAN you use]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF

• Can I create a slide show of slider/image carousel with the possibility for the links and the widths of the image to an Adobe program variable and then place in Muse

  Hello

  I really hope someone can help me with a project that led to drive me to despair.

  I'll put up an online art gallery, last year, I used Wix to create a site (explorersglobalfineart.com). Initially, I thought it was a good idea that I could build the mobile site with the site of the office. It turns out that features model are appalling and every time I add a new page I have to reinstall everything on the mobile site.

  In the last month, I've searched Adobe Muse. I started to build the site map and added to the artist page, but there are pages on the current site which have a slider carousel with the possibility for widths of the variable image and links that I cannot emmualte in Muse - http://www.explorersglobalfineart.com/#! Asia/cfvg

  Is there an Adobe program that I can use to create a cursor image carousel with the ability to tie and use images with varying widths which is compatible with Adobe Muse?

  Thank you very much

  Rebecca

  You can try this:

  http://musewidgets.com/products/carousel-Gallery-Widget

  Thank you

  Sanjit

• 802.3ad link Aggregation - 4 NETWORK cards

  I'm working on a project that requires four physical NIC be connected to two separate Cisco switches for redundancy.  I need access to a minimum of six networks through these four physical NETWORK card ports using ESX 3.5.

  Our plan is to use the Routing and aggregation (Etherchannel) on Cisco switches.  What we want to do is basically aggregate two NIC physical port trunks to each of the two switches Cisco Etherchannel.  We would allow routing based on IP hash on the unique vSwitch with four network adapters are associated.  We would use a separate vSwitch for vSwif0 and vmkernel port not part of the trunks.

  Seems this configuration good to you?  Looking for networking people comment on the above configuration.  Thank you.

  This is a discussion that asked the same question.

  http://communities.VMware.com/docs/doc-5000

  This is an insertion of the blog of Kevin Cline.

  http://kensvirtualreality.WordPress.com/2009/04/05/the-great-vswitch-debate%E2%80%93part-3/

  A technical requirement for the use of hash of the IP, it's that your physical switch must support 802.3ad static aggregation of links. Often, this means that you have to connect all the natachasery in the vSwitch to the same pSwitch. Some switches high-end support links grouped in pSwitches, but many do not. Contact your switch vendor to find out. If you do not have to put an end to all the natachasery in a single pSwitch, you introduced a single point of failure in your architecture.

  If your provider supports the links grouped in all of pSwitches, great.  Otherwise, you may need to consider another approach.  You can have redundancy between switches without etherchannel and just routing based on originating port ID.  So you could create a vSwitch with 4 NICs (two on each pSwitch) without a trunk and let ESX base for outbound traffic load balancing.  From my experience, you are much more likely to be CPU or memory bound as bound network.

• Is possible to create link?

  I use LiveCycle designer as part of Acrobat 9.  Is it possible to create a link in LiveCycle?  If so, it is not obvious to me.  How to do this?

  You have 2 options to use...

  You can place a button and change the border to white. In the legend set the police to highlight. In the click event, you can write code to open a URL.

  You also have an option to create the hyperlink from the Insert menu-> hyperlink... To use it, place a text on the form object and then place the cursor in the text and select Insert-> Hyperlink.

  Thank you

  Srini

• Satellite L875D: There is possibility to enable virtualization in the BIOS?

  Hello

  I want to buy Toshiba L875D-S73.

  I know supports CPU AMD - V required for the performance of like Microsoft Hyper-V virtualization.
  But I don't hear anything about BIOS.

  Is - this ability to enable virtualization in the BIOS?
  Maybe you know?

  Unfortunately I do not have this model laptop but I guess there is no option for virtualization in the BIOS. If the processor supports the it, it must be enabled by default.

  I m not sure but I think that laptops equipped with platform AMD do not support virtualization technology, so in my opinion, you should buy model with no D in the name. All models with D have the AMD platform.

  Contact your local dealer and ick information on other models of laptops.

• Satellite C855D - not possible to enable virtualization in the BIOS

  I just bought a portable Satellite C855D with a processor AMD A8 - 4500M. The processor supports AMD - V, but it is disabled in the bios. It seems that Toshiba has removed this option from bios InsydeH20 Setup and it is not possible to activate this feature.

  There is no work around for this problem? I bought this laptop for my studies and it will be returned if it is not possible to run 64-bit virtualization.

  I doubt that you will be able to allow this future if it is not taken in charge by the BIOS

  However, you can always try to update the BIOS, where an update would be available

• I have configured Link Aggregation on two Switch SF300

  The two links connect to both switches via two radios. The problem is that I can't access the attached radios http interface:

  radio_on_aggregation.PNG

  

  Everything else works fine and the radios are passing data according to PRTG monitoring of the towed gear

  Thank you

  Well, it looks like this is it.
  She looks like that ever, you can manage your bridges because of this.

  This is due to the notion of the Association and its operation
  L3 from the IP address of bridge management package can never be process as the etherchannel does not recognize. He treats only packets from his peers, etherchannel port in the etherchannel port.

  Overall, you cannot manage your bridges, to put it simply

• Is it possible to create links to re - run dynamically, where the URL changes for each contact?

  Hello world

  Wanted to understand a better approach on how to take the links that are dynamic, can be stored in the contact name field, and then convert on redirect links when sending an email. Does anyone do this?

  We have a use case where we want to send one every day by e-mail, but every time we send, change URL, and of course, we want to track clicks on URLS.

  All suggestions are appriciated.

  Thank you

  Amit Pandya

  The URL must define documents / web pages where the customer can read most relevent information to update their interest. The URL can be in CMS (Content Management System) or CRM (Customer Relationship Management) system. In both cases, the goal is to serve the most relevant information by email.

  Have already tried mergers field, and of course, it does not work.

  Also, ask yourself if it can be done by using the API, before put us the effort in the development of programs to generate direct emails and re-links used API.

  Another option.

  If someone has done this, would appriciate some clarification.

• Is it possible to enable the gpu to gtx670 in the first cc use?

  Hello

  I bought creative cloud and with first, I have no option to select the GPU support. I know that the GTX 670 is not in the whitelist but it works collaboratively with first Pro CS 6 and has more than 1 GB of Ram. So I hope that I can select the use of GPU rendering and click on the warning message now.

  Is it possible to allow the GTX 670 in first Pro CC?

  Thank you and best regards

  Uwe

  Don't know how to solve your problem outside the research to see if there is a file cuda.txt... but I can assure you that the card works in body CC2014.xxx because I use one.

  Try to reinstall the latest driver.