Router Cisco Small business with the functionality of the link aggregation

Similar Questions

• Plug-and-Play for Cisco Small Business 300 Series managed switch

  Nice day

  What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?

  It seems there are not, the operating system is not the standard IOS I used to.

  I would use with ability to bridge the Infrastructure first Cisco PnP.

  Concerning

  Stone

  First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.

  Seal a document shows how this is done.

  Hope that the information would be useful.

• Accounting on a Cisco Small Business SF300-08

  Hello

  "Cisco Small Business 300 Series managed switches Administration Guide" and the sheet indicate that this switch can make requests of accounting with a Radius server. On the switch interface/CLI SF300, there is that the authentication port, the port of account cannot be resolved (and nothing is sent by the switch to the default port). I guess that the SF300-08 doesn't manage accounting. Maybe I need to change to another model. Could you give me another model in the same price range?

  Thank you

  Laurent.

  Hi Laurent, I am pleased that the 1.2.5.70 has solved this problem.

  Please keep Advisory of the 1.2.5.70 firmware has also been lifted for now.

  Please note that we have identified a potential problem with the 1.2.5.70 update for the series 200, 300 and 500 switches. As a precaution, we took down the 1.2.5.70 free while we determine the cause of the issue, the seriousness and the scope. We re - ask the release or publish an updated based on the results of our analysis.

• Configuration of SNMP on Cisco Small Business 300 Series managed switch

  Please can someone help me configure SNMP on Cisco Small Business 300 series switch?

  Thank you

  Hi Anton,.

  Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...

  also, you will find useful documents for configuration etc on our server community kb:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...

  Let us know if you have any problems.

  Aleksandra

• Beginner jQuery is having trouble with the links and the page redirect and page caching.

  Hi all

  I'm trying to update an old legacy of multipage site (each page has headers html etc.), adding jQuery Mobile. Most of the time it goes well, but I'm having some problems with the links, the redirect of the page, and caching.

  I write javascript like this...

  < script >

  -do things - then-

  Window.Location.Replace ("Page1.html");

  < /script >

  and links like this

  
  

  < a class = "-ui ui-btn-b btn tsize1" href = "page2.html" rel = "external" > page 2 < /a > "

  
  

  CACHING ISSUES

  
  

  On many pages - such as those that I have problems with, I've added no caching of code as...

  < head >

  < META HTTP-EQUIV = "Pragma" CONTENT = "no-cache" >

  < META HTTP-EQUIV = "Expires" CONTENT = "-1" >

  ... more...

  < head >

  Problem: for example, I can go to Page 1 and click on a link to go to page 2 and page 2 has the lines "no cache" header. The problem is that a fresh change of page 2 does not appear even with no cache lines above and even if I hit refresh in the browser that I thought it was supposed to reload the page (live get of the site). On the contrary, it seems to continue to see the old content before the update.

  In another case I could be on page 21 and click on a link that goes to the publicationfootnote22 and made a few treatment database and then goes to the page33. In this case, my fees top22 updates are not appearing and showing just the old cache data.

  Q: what is the best way, at least while I am writing code, to force the Page to refresh (non-cache), I can see my updates all the time, because otherwise it becomes very confusing because I'm sure you know.

  Thanks in advance: Dave

  Hi Dave,.

  Are you handy with your developer tools? It's always where I head when I need to look inside something. Before getting anywhere in addition or developed, check the response code you get for the page request and see what is the numeric code. If it is 200, you get a new copy. If it is 304 then your browser is striking the same content or something in your UI is to preserve the previously loaded document fragment.

  Photos make it easy, Chrome this is grabbing a small page for the first time and with disable cache enabled, and we get the status code 200:

  

  If I keep refreshing with "Disable cache" activated so I keep getting GET/200, copy fees.

  However, delete the "disable cache" to speed things up and the server and the client negotiate and check if she even needs to send you the document (if she thinks she's changed), and if not, of course you GET/304, or "load cache:

  

  Whenever I update I get GET/304, hitting the cache.

  Make sure your requests are GET/200 if you expect not to be cached.

• can someone help me with the link to download hp2050 print drivers that are compatible with windows 8.

  can someone help me with the link to download hp2050 print drivers that are compatible with windows 8, my software CD is not compatible with windows 8, and I can't use the printer now.

  Hello

  The installation program "Full Feature" can be found on the following link.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-109407-2&cc=us&DLC=en&LC=en&OS=4132&product=4027469&sw_lang=

  Kind regards

  DP - K

• How to send an email with the link that has the user id?

  Hello everyone, I'm trying to send an email with the link that includes the user id. After users click the link, they should be able to see the form with their information that has been previously fulfilled. So my question is after I have send email how and what is the best way to get information and show it to the user. What should be separate page with the cfquery limited on the id user or something else? If anyone has an idea of what is the best way to do it please let me know. I already have my code who send e-mails.

  You save all the fields submitted initially to a database?  If so, run a query and then convert them to the form field, query values. I don't know what looks like your data (or database), but a simplified version might look like this.

  SELECT FirstName

  OF SavedFormTable

  WHERE ID =

• Error downloading Photoshop element 12: Arvato Berthelman - Download Manager error - unfortunately, there is a problem with the link to that file. This problem may be due to the number of users trying to download

  Error message when downloading Photoshop element 12: (I bought the license in a store)

  Berthelman arvato-

  Download Manager error-

  Unfortunately, there is a problem with the link to that file. This problem may be due the number of users trying to download the file, or the product may no longer be available. Please as minutes of a few in. If this privilege is still not available, please contact customer service at the address [email protected] or number 604-915-5200

  == > Les DEUX @ and phone number are fake!

  Hi Mireille56,

  The place where you are trying to download the software.

  [email protected] is not an email from Adobe Support.

  Please try to download Photoshop elements 12 of: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us&sdid=ZPQM

  Kind regards

  Rave

  < translated="" via="" google="">

  Hi Mireille56,

  Where you are trying to download the software.

  [email protected] is not an Adobe support email.

  Please try to download Photoshop elements 12 from: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us&sdid=ZPQM

  Kind regards

  Rave

• Problem with the links?

  I have recently upgraded to inDesign CS5 to CS4 and have some documents that I update.  The work links seem to be broken.  I update the links, then the connection breaks again in a few seconds.  I tried to update the original work on CS5, but the problem remains. I have created a document inDesign CS5, placed one of my files have, saved, closed.  When I reopemned the file - I had the same problem with the link.

  My main concern is more with CS5, CS4 and all of my previous work.

  All the patches or for that?

  OK, but they are on your hard drive or on a network location, somewhere?

• Suddenly our router keeps losing the internet.   The representative of the Cox says that IPV6 on the router is not compatible with the Cisco modem.   I'm turning it off?   Who is?   All started 3 days ago.   Have to reboot AirPort Extreme

  Suddenly Tuesday, our wifi stopped working.   Cox can not see anything on their end.   So far, we had to restart 5 times.   I finally realized that it is not the modem (Cisco), but our AirPort Extreme.   That's all that needs to be restarted.   I talked to a technician that I got to know, and she said that this week this problem started occurring with customers who have extremes of the airport.   Something about the airport in IPV6 and this is not compatible.   Before systems were PVI until the numbers came out (?)   In any case, she said Cox could not fix this, that I needed to talk to Apple to see if I could disable IPV6, at least for now.   I think I see how to do this, but does it make sense to anyone?   We have a new modem, installed in January, Cisco DPQ3212, good speeds, no issues whatsoever until this week.   There are also 2 other friends here (Scottsdale, Cox) with extremes of the airport.   Any suggestions?

  Cox has made a number of recent changes to their service, and they are trying to integrate IPv6 technology into their signals. They have not fully implemented the changes that must be made, and not commit to a date where things will be fully installed.

  Everything was fine until Cox implements these recent changes, and now Cox is blaming the problem on Apple. Apple has a different answer, as you can imagine. It is typical among manufacturers... blame the other guy.

  Apple routers are picking up some of the information they need to work with IPv6 and Cox, but since Cox has not completed the process, you'll probably best results trying to not use IPv6 with the airport router at all until you receive word of Cox that their systems are ready.

  The bottom line to this problem can be resolved by asking "What has changed".  The answer is Cox has changed.

  Configure your router to the airport most convenient to use IPv6 local link parameters only for now, to see if this will help.  You will not be able to realize all the benefits of IPv6 at the moment, but I hope that things will improve.

  

• NEITHER route can be started with the minimized window?

  We have a problem, while the GPIB instruments will not work unless NO-Trace is running.   So we have NO-Trace in our marketing so that it works when we start our test station.  But this great Trace window is disruptive to users, until they minimize the window.  Is it possible to have start OR route running, but also start with minimized window?  (Yes I know there is the box to get the Trace from OR Trace execution, but we would like that the window is running in the background - (reduced) to allow our Test window to not be in conflict with the Trace window).

  Well, it changes things because this is very probably an executable VEE? problem. Just spitballing here, but I'm guessing it's a thing of Agilent VISA OR VISA vs. As I've never used vee, I'm guessing they're using Agilent IO libraries. It looks like you can access the VISA Agilent as secondary depending on p35 here and here.

  As I said this is just a guess since I'm not familiar with VEE. I would like to confirm on the Keysight forums.

• CISCO ASA 5515 WITH THE VERSION OF FIREPOWER

  ASA 5515 service with the power of fire. Can be managed with ASDM firepower. ?

  Anyone suggests Versions for firepower, ASDM, ASA?

  Kindly help

  You will find it useful to install the Module of firepower on ASA for the management of the premises:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  Thank you

  Guillaume

  Rate if this can help!

• Redirect port on the router Cisco 881 can following the active WAN Interface

  Hello

  Is there a way to make the port Fowarding after the Active Wan Interface?

  In this case the port Fowarding only works when the interface is active is GigabitEthernet0/0

  Bureau3616 (config) # ip nat inside source tcp static 192.168.2.xxx 3389 interface GigabitEthernet0/0 3387

  If our ISP-1 failure on WAN-1 Interface GigabitEthernet0/0 switch to internet access automatically to ISP - 2 WAN-2 on GigabitEthernet0/1 but the port forwarding does not work because it is fixed to the other interface only and I is not the way to port forwarding follow the WAN an actress.

  Let me know please if anyone has an idea.

  It is a part of my config

  ! NAT configuration

  Bureau3616 (config) # ip nat inside source map route NAT-WAN1 interface GigabitEthernet0/0 overload

  Bureau3616 (config) # ip nat inside source map route NAT-WAN2 interface GigabitEthernet0/1 overload

  Bureau3616 (config) # NAT-WAN1 allowed 10 route map

  Ip address of Bureau3616 (config-route-map) # match 100

  Bureau3616 (config-route-map) # match interface GigabitEthernet0/0

  Bureau3616 (config-route-map) #exit

  Bureau3616 (config) # NAT-WAN2 allowed 10 route map

  Ip address of Bureau3616 (config-route-map) # match 100

  Bureau3616 (config-route-map) # match interface GigabitEthernet0/1

  Bureau3616 (config-route-map) #exit

  ! Port Fowarding configuration

  Bureau3616 (config) #ip avant-protocole nd

  Bureau3616 (config) # ip nat inside source tcp static 192.168.2.xxx 3389 interface GigabitEthernet0/1 3387

  Thank you!

  You can, but you can't use transfer based on the interface of the to do. It should be based on the address itself. It's fine if you have static addresses or reserved on your WAN interfaces, but pose a problem if the addresses are dynamic:

  ip nat inside source static tcp 192.168.2.x 3389 1.1.1.1 3389 route-map NAT-WAN1ip nat inside source static tcp 192.168.2.x 3389 2.2.2.2 3389 route-map NAT-WAN2

  Replace the address of your interface WAN1 and 2.2.2.2 with the address of your 1.1.1.1 WAN2 interface. Applying the road maps will work pretty much the same way as it does with your statements of overload. Each transmission NAT rule applies only to the traffic corresponding to rules of the road map.

• Small problem with the events of the listener

  I have a small interface with 5 radio buttons and a buttonfield and when i click buttonfield I create an event. all this works fine, but when I want to go back to the previous page I see pop up with 3 had to 'save, ignore, reject' and when I click on one of them I create a duplicate of the trial before.

  How can I go to the previous page without showing the pop-up with 3 coiches and without creating duplicate event?

  It's the listener code

  FieldChangeListener listener = new FieldChangeListener() {}
        
  ' Public Sub fieldChanged (field field, int context) {}
   
  {if (delivery. IsSelected())}
                             
  Time zone tz = TimeZone.getTimeZone ("GMT"); We want the time gmt
  Calendar gc = Calendar.getInstance (tz);  It gives the time date and gmt
                   
  int ore = gc.get (Calendar.HOUR_OF_DAY);
  int min = gc.get (Calendar.MINUTE);
  s int = gc.get (Calendar.SECOND);
                   
  Co co = new coordinate (longitude, latitude, ore, min, sec, 9, "Delivered");
  CoorVect.addElement (co);
  Dialog.Inform ("send event");
                     
  } else {}
  {if (GuastoMeccanico.IsSelected ())}

  Time zone tz = TimeZone.getTimeZone ("GMT"); We want the time gmt
  Calendar gc = Calendar.getInstance (tz);  It gives the time date and gmt
                       
  int ore = gc.get (Calendar.HOUR_OF_DAY);
  int min = gc.get (Calendar.MINUTE);
  s int = gc.get (Calendar.SECOND);
                       
  Co co = new coordinate (longitude, latitude, ore, min, sec, 9, "Guasto Meccanico");
  CoorVect.addElement (co);
  Dialog.Inform ("send event");

  } else {}
  {if (IncidenteStradale.IsSelected ())}

  Time zone tz = TimeZone.getTimeZone ("GMT"); We want the time gmt
  Calendar gc = Calendar.getInstance (tz);  It gives the time date and gmt
                        
  int ore = gc.get (Calendar.HOUR_OF_DAY);
  int min = gc.get (Calendar.MINUTE);
  s int = gc.get (Calendar.SECOND);
                        
  Co co = new coordinate (longitude, latitude, ore, min, sec, 9, "Incident Stradale");
  CoorVect.addElement (co);
  Dialog.Inform ("send event");

  } else {}
  {if (LavoriInCorso.IsSelected ())}
                           
  Time zone tz = TimeZone.getTimeZone ("GMT"); We want the time gmt
  Calendar gc = Calendar.getInstance (tz);  It gives the time date and gmt
                         
  int ore = gc.get (Calendar.HOUR_OF_DAY);
  int min = gc.get (Calendar.MINUTE);
  s int = gc.get (Calendar.SECOND);
                         
  Co co = new coordinate (longitude, latitude, ore, min, sec, 9, "Works in Corso");
  CoorVect.addElement (co);
  Dialog.Inform ("send event");
  } else {}
  {if (SenzaConsegna.IsSelected ())}
                                        
  Time zone tz = TimeZone.getTimeZone ("GMT"); We want the time gmt
  Calendar gc = Calendar.getInstance (tz);  It gives the time date and gmt
                          
  int ore = gc.get (Calendar.HOUR_OF_DAY);
  int min = gc.get (Calendar.MINUTE);
  s int = gc.get (Calendar.SECOND);
                          
  Co co = new coordinate (longitude, latitude, ore, min, sec, 9, "Not delivered");
  CoorVect.addElement (co);
  Dialog.Inform ("send event");

  } else {}
  Dialog.Inform ("Nessun elemento indication!");
  }
  }
  }
  }
  }
  }
  };

  Added on-screen, this code will replace the popup screen.

  I don't understand the second part of the question, that is to say the second invent.  Add this code and make sure that the popup is removed and then tell us if all your problems are solved.

  Also search the doc for this method in the object Screen to understand how it works.

  /*
  * Override to ignore the save/discard/Cancel dialog box
  */
  public boolean onSavePrompt() {}
  Returns true;
  }

• CONNECTION PROBLEMS WITH THE ROUTER (NETGEAR) - no problem with the provider of speed as it has been checked__

  • Programs you have problems with - very slow connection with all pages
  • Error messages - on the profile of my son is unable to connect at all with the error message
  • Recent changes made to your computer - windows 7 but added meeting the problem before this
  • What you have already tried the problem - claimant contacted no problem with their connection

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Hello

  Reinstall the NIC drivers
  Reset the router and check.