PowerConnect 6224 VLAN down?

Similar Questions

• PowerConnect 6224 VLAN created, but impossible to do a ping between customers

  1 created vlan 2 with two ports 17.19 with ip 10.0.1.2/24

  2 created vlan 3 with two ports 13.15 with ip 10.0.2.2/24

  attempt to create inter routing vlan

  1 pc windows connected with ip 10.0.1.3/24 and a gateway to port 17 10.0.1.2

  2 connected windows pc with ip 10.0.2.3/24 and a gateway 10.0.2.2 to port 15

  Unable to get the Ping between two clients any help would be much appreciated, thank you in advance and running config pasted below

  coresw1 #show running-config
  ! Current configuration:
  ! Description of the system "PowerConnect 6224, 3.3.7.3, VxWorks 6.5.
  ! 3.3.7.3 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2-3, 5
  VLAN 2 1 routing
  VLAN 3 2 routing
  output
  location of SNMP Server "Data Center"
  contact SNMP Server «»
  hostname "coresw1".
  unicast SNTP client enable
  10.0.0.1 SNTP server
  clock timezone 5 minutes 30 zone 'IST '.
  battery
  1 1 member
  output
  IP 10.0.0.193 255.255.255.0

  by default-gateway IP 10.0.0.1
  IP - peekaygroup.com domain name
  name-server IP 10.0.0.1
  without enabling ipv6
  IP routing
  interface vlan 2
  name "LAN1.
  Routing
  10.0.1.2 IP address 255.255.255.0
  bandwidth 10000
  IP mtu 1500
  output
  interface vlan 3
  name "LAN2.
  Routing
  IP 10.0.2.2 255.255.255.0
  bandwidth 10000
  IP mtu 1500
  output
  interface vlan 5
  name "RIL Internet"

  output
  level of 8a9f2a72d65baf40b48108874cd50592 user name 'admin' password encrypted 15
  !
  interface ethernet 1/g13
  switchport access vlan 3
  output
  !
  interface ethernet 1/g15
  switchport access vlan 3
  output
  !
  interface ethernet 1/g17
  switchport access vlan 2
  output
  !
  interface ethernet 1/g19
  switchport access vlan 2
  output
  !
  interface ethernet 1/g20
  switchport access vlan 5

  output
  !
  interface ethernet 1/g22
  switchport access vlan 5
  output
  SNMP-server community public rw
  output

  This blog does a good job of showing the different firewall rules to add. You said that you have already tweaked the firewall some, I would just check the measures taken.

  http://www.sysprobs.com/enable-ping-reply-Windows-7

  If there is no antivirus software installed, try a break/disabling it to test and see if it makes a difference.

  I don't see anything on the config which would prevent pings happen.

• PowerConnect 6224 VLAN config / default gateway

  Hello

  I am new to configuring a VLAN and work with DELL going on so please forgive my ignorance.

  I joined a small agency that currently has a flat structure networking including 1 6224 linked to two 5548 one is connected to three 3548 (access), and the other is connected to a server. The 6224 connects to a proxy (default gateway), and then on the Web. All devices are currently on a 192.168.78.0 24 network with ip default gateway 192.168.80.1

  We want to segment the network using two VLAN initially. VLAN 1 user "80" and vlan 1 safety '70' and I want to clarify a few things before that I try:

  1. can you stay the ip on the network switch for vlan user ex: 192.168.80.123 or should I create a vlan separate management?

  2. I know in order for the inter - vlan, the ip of the gateway routing vlan must be on the 6224 and I then have to configure a default route to the proxy. The proxy must be on one VLAN separate or could I leave on VLAN 80 and change the ip address another que.1?

  Thanks in advance.

  I did it several times myself.  You can do almost an infinite number of ways, but it will be better to stick to certain typical networking practices.  Here is the version digest readers of what would be preferable to do so.

  1 enable routing on the switch stack.

  2. make a 80 VLAN for your network 24.80.  Assign the IP 192.168.80.1 to this VLAN.  In this way, customers will now be a ".". 1' default to the network gateway, they are on.

  3 make an another VLAN 70 for your network 24.70.  Assign the IP 192.168.70.1 to this VLAN.  This will be the default gateway for the network.  Repeat for however many VLANS / networks you want to.

  4. create a separate VLAN for his own 'bubble' network between the switch and the upstream proxy server.  (Lets call him a dummy VLAN 100 with an IP range x.x.100.x 29.  It can be just a little/29 block or something or 24 if this is confusing. Configuring the ports a few ports 'access' for this VLAN for that no marked traffic pass over this network.  Set x.x.100.1 to your Proxy Server and x.x.100.2 to your switch, then make sure you have directions on both sides about where traffic should go.

  5. save your configuration so that you have to rebuild it after a reboot.  :-)

  It will be best to set your expecations about it.  You want realistic during a weekend/maintenance window.  ARP cache and other issues can make for some downtime.  In addition, there are certainly other ways to do it, but that may be hurtful on the road when you need to increase or scale.  Two years on the road someone wondered why a default gateway is on a few eccentric IP, or there are errors of routing intermentent, etc..

  Powerconnect worldwide, just be clear what is the difference between a port of "access" to the port of 'general', and are a port 'trunk '.  Conditions may be different from the Lim to make, and if one comes to tell the world of Cisco, this may be a little different.

  Finally, don't forget to come up with a good procedure for this during your maintenance window.  Come up with a good plan documented and so well thought out, when run you it, it will be nothing more than a task in office project.

• PowerConnect 6224 VLAN Routing, unable to connect out of VLAN but able to connect by entering.

  To set up a new VIRTUAL local network to separate the common workstation network and obtain new DHCP scope, I had a few questions and found advice in the post of http://en.community.dell.com/support-forums/network-switches/f/866/t/19370806.aspx?PageIndex=3 but now I find that my traffic is not going through properly so I'm starting a new thread to get help shows all of working.

  Current primary network 192.168.1.0/24 (192.168.1.200 DHCP server). Adding new perspectives to the server for 192.168.3.0/24 active.

  Gateway default 192.168.1.0/24 is 192.168.1.254 (Cisco ASA, it was set up like that when I arrived and no room to insert the dedicated router). Adding route to 192.168.3.0/24 > 192.168.1.253 (PC6224 and VLAN 1 management interface). I also added exceptions NAT asa for the 192.168.3.0 network.

  I was still having some problems of scathing to the 192.168.3.0 network from the DHCP server and I added a static route on the server for this network, bypassing the ASA for routing to the switch.

  From the DHCP server, I am able to ping 192.168.1.253, 192.168.3.254 but not a laptop that runs Windows XP configured with 192.168.3.1 address connected to port 22 of the 6224.

  The XP laptop, I am able to ping 192.168.3.254 but not 192.168.1.253 or any other address in the 192.168.1.0 network.

  The switch CLI, I am able to ping on both networks destinations.

  Here is my config of switch. I have it set to scrape factory reset so there is no buried old ACL inside.

  console #show run
  ! Current configuration:
  ! Description of the system «PowerConnect 6224P, 3.3.5.5, VxWorks 6.5»
  ! 3.3.5.5 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2
  VLAN 2 1 routing
  output

  IP 192.168.1.253 255.255.255.0
  by default-gateway IP 192.168.1.254
  IP - domain.local domain name
  name-server IP 192.168.1.11
  name-server IP 192.168.1.200
  IP routing
  IP helper-address 192.168.1.200 dhcp

  interface vlan 2
  name 'common '.
  Routing
  192.168.3.254 IP address 255.255.255.0
  IP netdirbcast
  bandwidth 10000
  business assistance-address IP 192.168.1.11
  field of IP helper-address 192.168.1.200
  IP helper-address 192.168.1.200 dhcp
  IP mtu 1500
  output

  l2relay DHCP
  DHCP l2relay vlan 2
  !
  interface ethernet 1/g21
  switchport access vlan 2
  output
  !
  interface ethernet 1/g22
  switchport access vlan 2
  output
  !
  interface ethernet 1/g23
  switchport access vlan 2
  output
  !
  interface ethernet 1/g24
  switchport access vlan 2
  output

  
  

• How to access the management of VLANs with a different virtual LAN (Dell powerconnect 6224)

  Hello

  DELL powerconnect 6224 reference.

  I want to access the management of a different VIRTUAL LAN VLAN.

  The management of VLANS is 100 of VLAN. not the routing

  My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.

  Thank you for your help on the command line

  The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.

  See you soon

• Transit VLAN on the PowerConnect 6224

  I need help to sort out a problem with routing on a 6224 we have configured to act as a vlan transit for one of our branches.  The general idea is 8.143 is the vlan of transit, of 8.144 is our PC LAN 8.145 will be our VOIP lan.

  We have installed this switch with our WAN provided last week, but had to get out. Traffic seemed to happen to the WAN providers to our transit interface VLAN (172.22.143.254) wasn't going anywhere.  It's symptoms

  (1) we could ping from 172.22.144.x to 172.22.145.x and 172.22.143.x

  (2) we could ping from 172.22.145.x to 172.22.143.x and 172.22.144.x

  (3) we could ping from 172.22.143.x to 172.22.144.x and 172.22.145.x

  (4) if I was plugged into the 6224 on with an address 143.x I could ping our remote control does site at 172.22.8.x no problem but not 144.x or 145.x

  (5) 172.22.8.x, I couldn't ping 144.x or 145.x or 143.1 (I could ping 143.254 which is EXTENDED to suppliers to our switch network interface)

  Here's the running to the switch configuration.  Any suggestions would be greatly appreciated:

  Console > activate

  Console execution #show

  ! Current configuration:

  ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.

  ! 3.3.6.4 system software version

  ! Passage mode is configured as disabled

  !

  Configure

  database of VLAN

  VLAN 143-145

  VLAN routing 143 1

  VLAN routing 144 2

  VLAN routing 145 3

  subnet of VLAN association 172.22.143.0 255.255.255.0 143

  subnet of VLAN association 172.22.144.0 255.255.255.0 144

  subnet of VLAN association 172.22.145.0 255.255.255.0 145

  output

  battery

  1 1 member

  output

  DHCP IP address

  IP routing

  IP route 0.0.0.0 0.0.0.0 172.22.143.254

  interface vlan 143

  Name the "Transit".

  routing ip address 172.22.143.1 255.255.255.0

  output

  interface vlan 144

  name "TWLAN".

  routing ip address 172.22.144.1 255.255.255.0

  output

  interface vlan 145

  the name "VOIP" routing

  IP 172.22.145.1 255.255.255.0

  output

  level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15

  !

  interface ethernet 1/g1

  switchport mode general

  VLAN allowed switchport General add 143

  output

  !

  interface ethernet 1/g2

  switchport mode general

  VLAN allowed switchport General add 143

  output

  !

  interface ethernet 1/g3

  switchport mode general

  VLAN allowed switchport General add 144

  output

  !

  interface ethernet 1/g4

  switchport mode general

  VLAN allowed switchport General add 144

  output

  !

  interface ethernet 1/g5

  switchport mode general

  VLAN allowed switchport General add 145

  output

  !

  interface ethernet 1/g6 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g7 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/8 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g9 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g10

  switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g11 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g12 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g13 switchport mode General General switchport vlan allowed output adds 145! General mode of interface ethernet 1/g14 switchport

  switchport general allowed vlan add exit 145! interface ethernet 1/g15 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g16 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g17 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g18 switchport mode General switchport General allowed vlan add 145

  output! interface ethernet 1/g19 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g20 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g21 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g22 switchport mode General switchport General allowed vlan add exit 145

  ! interface ethernet 1/g23 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g24 switchport mode General switchport General allowed vlan add to exit 145

  Console #.

  It seems that port 1 must be in the VLAN 143, not general mode access mode. You already have a static route in place on the PowerConnect switch which directs traffic to the next break in the network. But it may be necessary for a place on the Cisco that allows to direct traffic to the PowerConnect switch.

  Here is a good post to look through also.

  http://en.community.Dell.com/support-forums/network-switches/f/866/t/19506015.aspx

• VLAN between 2 powerconnect 6224 using XFP modules

  Dear friends,

  I have 2 switches powerconnect 6224 interconnected using optical fiber and XFP ports on the rear panel of the switch.

  There is no configuration of the battery between them.

  The distance between the two switches is 500 metres and they both work correctly when you use the vlan by default (use of the LAN)

  I created a virtual LAN using 2 ports on a firewall and I created the same vlan on the second firewall, but I can't see a VLAN traffic goes to the other.

  Also, I tried to configure the port as trunk but same result.

  The vlan works very well in a single switch, but traffic is not able to flow to the second switch.

  You have an idea why does not?

  Maybe is not posible to have VLANs using xfp connections...

  Any idea would be greatly popular.

  Thanks in advance!

  Rear ports are labeled xg1, 2, 3, 4. So, if the connection is made using the xg1 on a single switch for xg1 on the other switch. Then you enter interface 1/xg1 and make configuration changes.

• VLANs for PowerConnect 6224

  Hello

  I bought Dell PowerConnect 6224 & I'm newbie for VLAN management. To put it simply, how can I create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without defining the point of gateway for the network servers and workstations to the ip address of vlan?

  Thank you.

  Here is a link to the manuals available for the Dell PowerConnect 62xx:

  support.Dell.com/.../index.htm

  Creation of VLANS

  Console > activate

  Console # config

  Console (config) # vlan database

  VLAN console(config-VLAN) # 10

  output console(config-VLAN) #.

  Console (config) # interface vlan 10

  # Ip address 255.255.255.0 192.168.10.x console

  Console # name Marketing

  Console # end

  console # show vlan

  Creating Ports for PC to connect as a ignorant guest VLAN.

  Console > activate

  Console # config

  Console (config) # interface ethernet 1/e1

  Console # switchport mode access

  Console # switchport access vlan 10

  Console # end

  Enable routing

  To globally enable IPv4 routing on the router, use the command "ip Routing".

  in Global Configuration mode.

  Console (config) #ip Routing

  You will need to create the VLAN as described above.  Then, set the access mode for a port VLAN particular then set the PC with an IP address in the range of the subnet for the VLAN and the gateway as the IP address of the address that you provided for the VLAN on the port.

  Then once the routing is enabled in the world it should allow communication between VLANs and configured different subnets.

  Hope this helps,

• LACP LAG POWERCONNECT 6224

  Hi I m ussing a powerconnect 6224, I have equipment that works as a switch and it has two ports glued with LACP, when I connect this device to the POWERCONNECT and send a ping there is no answer, one that with a laptop computer connected to this port, it responds to the ping command. Can help you with this? Here is the configuration of the POWERCONNECT. Thanks in advance.

  Console (config) #interface vlan 32

  Console (config-if-vlan10) #ip address 10.163.101.4 255.255.255.252

  Console (config-if-vlan10) #routing

  Console (config) #interface ethernet 1/g3

  mode console (config-if-1/g1) #switchport general

  Console (config-if-1/g1) #switchport general allowed vlan add 31

  Close, more like this.

  Console (config) # interface range ethernet g2

  Console # channel - group 1 automatic mode

  output console #.

  Console (config) # interface range ethernet g3

  Console # channel - group 1 automatic mode

  output console #.

  Console (config) # interface port-channel 1

  Console # switchport mode general

  Console # switchport general allowed vlan 201 tagged

  Make sure that there are at least two ports in each LAG.

• Pwerconnect 6224: vlan client computers do not receive the ip address of DHCP server on a different VLAN

  Hello

  I have a prolem routing dhcp requests between the vlan management where DHCP server resides and the other VLANs.

  I have the scenario of base with three VLANS: vlan 10 (management vlan), 20, 30, configured on a Powerconnect 6224 switch L2 mode. This switch is connected to a pfsense router. The router is configured at the package of road between the VLANS and it does it well.

  In Vlan 10, I have a configured DHCP server to use the ip addresses of all the VLANS (10, 20, 30). VLAN 10 client computers receive ip address but not others from other VLANs.

  When I put the ip address in the appropriate range of VLANs manually on computers, I ping the server and I have connectivity.

  This suggests that the problem is with the dhcp package.

  The following is the configuration of the switch:

  Configure
  database of VLAN
  VLAN 10,20,30
  VLAN 1 1 routing
  VLAN 20 2 routing
  VLAN 30 3 routing
  output
  SNTP server time.nist.gov
  clock timezone 1 minutes 0
  battery
  1 1 member
  2 2 Member
  output
  DHCP IP address
  IP address vlan 10
  name of the IP-server 172.16.10.1

  bootpdhcprelay cidridoptmode
  interface vlan 1
  Routing
  IP 172.16.1.1 255.255.255.0
  output
  interface vlan 20
  Routing
  address 172.16.20.1 IP 255.255.255.0
  output
  interface vlan 30
  Routing
  IP 172.16.30.1 255.255.255.0
  output
  level of 20fc49459a1898b923ed3ec7b3e81276 user name 'admin' password encrypted 15
  No spanning tree
  spanning tree priority 0
  l2relay DHCP
  DHCP l2relay VLANs 10, 20-30
  DHCP l2relay circuit-id VLANs 10, 20-30
  !
  interface ethernet 1/g2

  l2relay DHCP
  switchport access vlan 20
  output
  !
  interface ethernet 1/g3
  l2relay DHCP
  switchport access vlan 30
  output
  !
  interface ethernet 1/g21
  switchport access vlan 10
  output
  !
  interface ethernet 1/g22
  switchport access vlan 10
  output
  !
  interface ethernet 1/g23
  switchport access vlan 10
  output
  !

  interface ethernet 1/g24
  switchport mode trunk
  switchport trunk allowed vlan add 10,20,30
  output
  Server SNMP community EyesOfNetwork ro
  SNMP-server community public ro
  output

  I followed the instructions in the powerconnect 6224 user guide, but no progress on this issue.

  Any help will be be grateful.

  Thank you

  Zoubeir

  The DHCP server stores information that could be useful? May need to configure monitoring ports and something as wireshark to monitor DHCP packets. This would help determine where the package is stopping.

  example:

  Console (config) #monitor session 1 source interface 1/g8

  Console (config) #monitor session 1 destination interface 1/g10

  session mode 1 #monitor console (config)

  right now I don't see anything in the config of the switch that stands out. If the DHCP server is configured for option 82, then you will need to include the following command on the switch.

  Example:

  Trust l2relay console #dhcp (config-if-1/g1)

  But I don't think that's our scenario here.

• Proxy-arp or local proxy arp? Reference Dell Powerconnect 6224

  We need allow some customers to resolve the mac address of a server that is located in a different range of addresses, VLAN and IP.

  I thought that the addition of the ip proxy-arp interface command vlan should do the job, but this command seems to be activated by default according to the reference guide, after that I tried to add the command he always show up on a running show. Which confirmed my thoughts. While I was looking for the solution that I saw another command that does not appear in the cli reference guide: local-proxy-arp ip. But since I'm not sure of what will make this command I am careful to hit just the command on the interface VLAN.

  How others send their arp on powerconnect 6224 requests?

  After reading my own source again, I realized that the thing that I want is not possible. It goes beyond the need to divide the network into segments. If all the query arp is transferred to other networks, there is a benefit less: you want to limit the broadcast domain.

  Static ARP is the thing I'm going to need to be implemented to solve this problem.

  Thanks for the clarification anyway.

• PowerConnect 6224 Switch Netgear L2 and

  Hi, I have now successfully configured my PowerConnect 6224, host and road between the 4 VLANS, I have access to the internet and can ping I have, is all great work. The next thing on my list is to set up my router L2 netgear to work with the port based VLAN, I want to connect L2 switch port 1/g23 on my PowerConnect 6224, as far as I understand this port must be a trunk port allowes all WHAM, here's them my config for the PowerConnect 6224:

  ! Current configuration:
  ! Description of the system 'Dell 24 ports Gigabit Ethernet, 2.0.1.8, VxWorks5.5.1'
  ! Version of the software system 2.0.1.8
  !
  Configure
  database of VLAN
  VLAN 10,20,30
  subnet of VLAN association 192.168.1.0 255.255.255.0 1
  subnet of VLAN association 192.168.2.0 255.255.255.0 10
  subnet of VLAN association 192.168.20.0 255.255.255.0 20
  subnet of VLAN association 192.168.30.0 255.255.255.0 30
  output
  battery
  1 1 member
  output
  1 priority 1 switch
  IP 192.168.1.1 255.255.255.0
  IP - xxx.xx.xx domain name
  Name 192.168.2.10 IP-server
  IP-name 192.168.2.30 Server
  IP routing
  IP route 0.0.0.0 0.0.0.0 192.168.2.201
  bootpdhcprelay enable
  bootpdhcprelay IP_serveur 192.168.2.10
  bootpdhcprelay cidridoptmode
  192.168.2.1 IP helper-address 192.168.2.10 37
  192.168.2.1 IP helper-address 192.168.2.10 49
  192.168.2.1 IP helper-address 192.168.2.10 137
  192.168.2.1 IP helper-address 192.168.2.10 138
  IP helper 192.168.20.1 192.168.2.10 37
  IP helper 192.168.20.1 192.168.2.10 49
  IP helper 192.168.20.1 192.168.2.10 137
  IP helper 192.168.20.1 192.168.2.10 138
  IP helper 192.168.30.1 192.168.2.10 37
  IP helper 192.168.30.1 192.168.2.10 49
  IP helper 192.168.30.1 192.168.2.10 137
  IP helper 192.168.30.1 192.168.2.10 138
  interface vlan 10
  "Name servers".
  Routing
  IP 192.168.2.1 255.255.255.0
  Send IP rip rip1 version
  IRDP IP
  output
  interface vlan 20
  the "sale".
  Routing
  address 192.168.20.1 255.255.255.0
  Send IP rip rip1 version
  IRDP IP
  output
  interface vlan 30
  name 'accounts '.
  Routing
  192.168.30.1 IP address 255.255.255.0
  IP netdirbcast
  Send IP rip rip1 version
  IRDP IP
  output
  level password user name 'michi' encrypted 15 4f70cfb1451a1b0ce0b872421bee6c1c
  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30
  output
  !
  interface ethernet 1/g3
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30
  output
  !
  interface ethernet 1/g4
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 20
  output
  !
  interface ethernet 1/g5
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30
  output
  !
  interface ethernet 1/g7
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10
  output
  !
  interface ethernet 1/g8
  switchport mode general
  switchport General pvid 30
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 30
  output
  !
  interface ethernet 1/g23
  switchport mode trunk
  switchport trunk allowed vlan add 1,10,20,30
  output
  !
  interface ethernet 1/g24
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30
  output
  output

  On my netgear L2 switch that I want to connect the port 24 to 1/g23 of my Dell switch, but I can't seem to be able to make it work somehow, here is my config to the Netgear switch:

  ! Current configuration:

  !

  ! Description of the system "GSM7224 L2 managed Gigabit Switch"

  ! Description of the system 6.2.0.14

  !

  Quickly define "GSM7224.

  Network Protocol No

  network settings 192.168.1.2 255.255.255.0 192.168.1.1

  database of VLAN

  VLAN 10

  10 name servers of VLAN

  VLAN 20

  name of VLAN 20 sales

  VLAN 30

  name of VLAN 30 accounts

  output

  Configure

  clock timezone "GMT" 0 0

  SNTP client unicast mode

  ! The SNTP server is active

  Server SNTP PooleOne.xxx.xx.xx

  set logging in buffered memory

  lineconfig

  output

  Storm-control flowcontrol

  name of the configuration of protocols spanning-tree 00-0F-B5-FC-BA-62

  public@10 SNMP-Server community

  public@20 SNMP-Server community

  public@30 SNMP-Server community

  IP - xxx.xx.xx domain name

  Name 192.168.2.10 IP-server

  192.168.2.30

  192.168.2.201

  interface 0/1

  pvid VLAN 10

  participation of VLAN include 10

  output

  interface 0/2

  pvid VLAN 20

  participation of VLAN include 20

  output

  interface 0/3

  pvid VLAN 30

  participation of VLAN include 30

  output

  interface 0/4

  output

  interface 0/5

  output

  interface 0/6

  output

  interface 0/7

  output

  0/8 interface

  output

  interface 0/9

  output

  interface 0/10

  output

  interface 0/11

  output

  interface 0/12

  output

  interface 0/13

  output

  interface 0/14

  output

  interface 0/15

  output

  interface 0/16

  output

  interface 0/17

  output

  interface 0/18

  output

  interface 0/19

  output

  interface 0/20

  output

  interface 0/21

  output

  interface 0/22

  output

  interface 0/23

  output

  interface 0/24

  Description "Trunk Port.

  marking 1 VLAN

  participation of VLAN include 10

  VLAN tagging 10

  participation of VLAN include 20

  VLAN tagging 20

  participation of VLAN include 30

  VLAN tagging 30

  output

  output

  First; is it possible to achieve what I'm trying to do with my equipment?

  Second; where I went wrong in my configs?

  Thank you very much for your help.

  
  

• How Reboot/restart Dell Powerconnect 6224

  Hello

  My company has 2 powerconnect 6224, 1 is the master and 1 slave, do I know how could restart/reboot my switch in the GUI?

  Can I use the cli to restart/reboot command and what is the command line.

  Thank you

  Using the CLI to recharge the battery, you must use the # reload command. You can add the number of the switch in the command reload members of chimneys. charge # 1, # reload 2.

  You can also use the command console (config-battery) #initiate failover. This command forces a warm restart of the battery. The unit of backup succeeds the new management unit without clear status of material on the stack members. The original management unit restarts.

  In the graphical user interface, you can reboot the switch with entering the system > general > reset. You can also start a recovery using System > stacking > NSF summary. Initiate failover will begin a warm reboot of the switch.

• PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

  I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
  6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

  I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

  I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

  Hope this info helps.

• Slave keeps restarting after unstacking-Dell PowerConnect 6224 switch

  Hello everyone;

  I have 2 switches (PowerConnect 6224) on the other. Because we are them stacked like we got new switches, we decided to remove the cables from the battery and use them as individual switches.

  So I tried to unstacking the first switches using CLI, but it does not, simply, nothing happens. So I took the cards accumulation off both switches and removed the stacking cables.

  Switch works fine, but the slave is restarted.

  I correct the following:

  Startup options, tried to reset, restore the production parameters, format... They look successful the config looks like this is done and once the switch starts it asks me if I want to run the Setup Wizard, but it will just freeze and restart.

  is there a way to fix it? or the switch is dead?

  All ideas are welcome

  Thank you

  I would like to download the latest firmware.

  www.Dell.com/.../drivers

  Disconnect all other devices from the switch and follow the instructions of XMODEM that are included in the download to Flash the firmware.