PowerConnect 6248 stacking using the front SFP Ports

Similar Questions

• I have a Photosmart 3210 - Can I use the front USB port instead of port back? (back is broken).

  Hello!  Trying to help a friend.  Rear USB port no longer his plug slips outside, no electrical connection.  Tearing in the unit for her brief submeter (out of warranty, nothing to lose).  Can I use an adapter with a standard USB plug on each end to connect to a PC for printing?  The user manual is too vague on this - looks like front USB is just for PictBridge stuff.  Any suggestions/ideas will be greatly appreciated.

  Thank you

  kott2ke

  Hello kott2ke,

  Front USB port: print photos directly from your camera or storage only.

  Rear USB port provides connectivity for printer and USB.

  Kind regards
  Jabzi

  Help the community by marking this post.
  Your question has been answered? Mark it as a accepted Solution!
  See a great post? Give it a Bravo!
  I work for HP

• iOS 10.0.1 "not allowed to use the restricted network port.

  I just upgraded my iPad Mini iOS 10.0.1. He is now running Safari 10. I tried to visit an internal/private IP on port 4190 using HTTP. I get an error that says:

  Safari cannot open the page.

  The error was: "not allowed to use the restricted network port.

  On iOS 9.3 using Safari 9, the same URL opens fine without this error.

  Do not know what has changed since iOS to iOS 10.0.1, 9.3 but I'm unable to visit a web site that I have visited before.

  I know that WebKit maintains a list of ports that you cannot go (e.g. 6666), 4190 is not a restricted port AFAIK. I don't know why I get this error message.

  It seems I was looking at the wrong source code.

  I finally got a clue where to look after visiting the page Web Safari Technology Preview 13.

  https://trac.WebKit.org/browser/releases/Apple/Safari%20Technology%20Preview%201 3/WebCore/platform/URL.cpp

  It seems port got 4190 recently added to the list of blockedPortList

  2306	2049, / / NFS
  220V	3659, / / apple-sasl / PasswordServer [addition of Apple]
  2308	4045, / / lockd
  2309	4190, / / ManageSieve [Apple adding]
  2310	6000, / / X 11
  2311	6665, / / alternate IRC [addition of Apple]
  2312	6666, / / alternate IRC [addition of Apple]
  2313	6667, / / standard IRC [addition of Apple]
  2314	6668, / / alternate IRC [addition of Apple]
  2315	6669, / / alternate IRC [addition of Apple]
  2316	invalidPortNumber, / / used to block all the invalid port numbers
  2317	};
  2318	const unsigned short * const blockedPortListEnd = blockedPortList + * _ARRAY_LENGTH (blockedPortList);

• Can I use the s - vhs port to send video to television on Satellite A100-338

  Can I use the s - vhs port to send video to my TV? I have a good s - vhs cable to SCART. However, I can't set up the laptop to use the port s - vhs. The driver intel graphics media accelerator thingy does not allow me to add tv as another device, because it's not reccognise as a screen.

  It's a Toshiba 21 '' bog standard CRT. Widescreen even not. I want to be able to use the media library.

  Hello Peter

  Of course, you can use this port. This port is there exactly for this purpose. Make sure to use right high quality cable and connect it properly on your TV. I use the same port on my Tecra. I also use adapter SCART like this one http://videoclub.tiscali.co.uk/img/scart_adaptor.gif and it works perfectly. Make sure you use the right settings on your TV.

• Cannot use the Micro-USB port on the coming Pro 11?

  Hello

  Can I use the micro-USB port to a mouse or other device (with Dell micro-USB to USB dongle for tablets)?

  Bought one as advertised and does not work...

  Thank you

  Hey guys, it seems that there is still much confusion over the functions of the port mictousb on the place of the 11 sessions pro.

  Anyone know if it is possible to use it for anything other than recharging? An OTG cable connected I have here doen't work on my 7130, but on ebay, some sellers here in Germany offer small hubs with OTG funcion specially for this model:

  http://www.eBay.de/ITM/kwmobile-3In1-micro-USB-hub-adapter-fur-Dell-venue-11-Pro-Schwarz-Verteiler-Kit-/361194175623

  Does anyone know for sure who is the truth?

  EDIT: also, as the microusb port has the logo of bolt on I guess this is the port used for the powershare function (if this feature is enabled in the BIOS). Does this mean I have to buy a microusb to microusb cable to recharge my mobile hollow 11 meeting places powershare function?

• Can I use the mini HDMI port to safely load my HX200V?

  I used the mini HDMI port to load my camera HX200V battery,

  but the battery does not very long load, even after being recharged.

  I have hurt the battery?

  Hi RickS8082,

• I just installed lihtroom CC and develop, the picture is blue. When I used the front then the image before is normal and blue again after.

  I just installed lihtroom CC and to develop the module, the picture is blue. When I used the front after, the before image is normal and the after looks always blue.

  I don't know what to do?

  See link below:

  https://forums.Adobe.com/thread/1823307

  6 Lightroom displays a blank blue screen with an X through it in the module development for all my photos

• HP Pavilion P7 - 1037c: my HP Pavilion desktop computer has been moved and I can't find the front USB ports. How can I find them?

  My computer has been moved to my new apartment and set up my movers for me.  I used to see some front USB ports at the bottom of the front panel, but now I can't.  Is there something I need to do?  I really need those!

  Slide the cover down. Look at this picture.

  

  Good day!

• Restart Powerconnect 6248 without disturbing the Configuration

  I apologize in advance for the entry-level position and if that's the answer elsewhere, please point me in the right direction:

  I inherited load on a network LAG / VLAN with a central 2-battery Dell switch Powerconnect 6248 functioning as a main switch and routing of traffic between the VLANs that are shared it resources.

  I want to restart this switch without losing any configuration, because I'm just to enter this network, I don't want to disrupt or rebuild the configuration.

  I can get Telnet or SSH access to the switch but now use the GUI. When I go to reboot I choose to restart the two batteries and am met with the message:

  "The unit will restart with the startup configuration, not the running configuration. Do you want to continue? »

  I had a contractor separate network restart the switch before and I don't know if it simply ignored the message and proceeded. I would like to be able to restart this switch without losing any configuration.

  My question is, I'm ok to move forward through this error message? Or do I need to configure backup to restart? What is the best way to proceed with a simple reboot of two chimneys, while maintaining the current configuration.

  Here is the procedure, I suggest you take.

  -If the running configuration is operational and you want to keep on the switch, and then save it in the startup configuration.

  -before to restart, save the configuration.

  -Keep the battery restart.

  You can then use this backup config as a reference in case something happens to the configuration of the switch. It's a good idea to take the habit of saving after all change config, before the updates of the firmware, reboot, etc.

  Here is an article that will guide you through the commands to perform these actions.

  http://Dell.to/1NPR5aY

  Hope you find it useful.

• Using the second ethernet port to connect to the printer?

  Hi I have a Mac Pro 2.1 old school and I'm wondering if I can connect to the network with an ethernet port and connect the latter to a printer?

  If so, how?

  Yosemite running.

  Thank you

  Physically, you use a port and a cable to connect to your network and use the second port and a second cable to connect directly to the printer. The printer must obviously have an interface Ethernet himself.

  However, you need to configure the second port on the Mac and the Ethernet port on the printer for each manually configured the TCP/IP addresses and these should be in a range of different network to your main network.

  If you the main network is something like 192.168.1.1 then your printer and the port on the Mac connection to this need to be in another network, such as 192.168.11.1.

  In theory, if the printer supports Hello aka. mDNS, then maybe you can get away with not having to configure TCP/IP addresses for the connection.

  The main reasons to use a second separate connection as this would be the performance or security, and frankly I don't think that's really relevant here. This would mean that no other computers on your network will be able to access the printer.

• Can I use the lan Ethernet port on the airport express to the release of music?

  Can I use the Ethernet connections on airport express at the exit of music over wifi to a set of speakers? I would use an Ethernet connector at one end a DIN 5 pin to a pair of speakers beolab 2500/2300. I don't want to use the PIN audio output on the Airport express, as it is analog. Possible music out through one of the Ethernet connections at the back of the Airport express? Thank you

  Can I use the Ethernet connections on airport express at the exit of music over wifi to a set of speakers?

  Sorry, but no.

  I don't want to use the PIN audio output on the Airport express, as it is analog

  Perhaps you weren't aware that audio port on the AirPort Express audio book Terminal analog or digital, according to the type of connector used. See this link on the AirPort Express specifications to confirm... http://www.Apple.com/Airport-Express/specs/

  In other words, for the Express deliver audio analog, connect a standard stereo mini plug with connectors appropriate to the other end.  To ensure that the Express deliver audio digital, plug a mini Toslink cable to the audio port on Terminal AirPort Express.  An example is in this link... Airport Express Toslink - Amazon.com

• Impossible to use the DVI - D port with cable DVI - D Pav 500-100 a to HP W2207 monitor

  I have a new standard of factory Pav 500-100a without mods.  HP w2207 monitor.

  Currently properly connect with VGA DVI - D port with the adapter supplied with the pc.  I have install Windows Update 8.1, put in my files from my old PC and everything was fine except the video is not very good.

  I got a formwork of cable DVD, but it's a DVI-I have the cable.  It took 5 minutes before windows comes up and then whenever the background picture changed in the theme which he suspended for a few seconds.  I read that I have a DVD-D need cable which i purchasd today.

  The package says it's a CL-DVI2M - DVI M/M 24 + 1 CABLE 2 M.  The tech in the store said that it is a good calbe and works perfectly.

  When connected and power until I get the hp and rolling points logo, then it turns off.

  I reconnect the cable VGA and all its beautiful - using the VGA to DVI.

  I ran msconfig and turned from secure boot - restarts and comes well in safe mode.  I set the resolution of 1280 x 800 and rebooted and reconnected the cable DVI - Virgin again.

  If I put the cable VGA back inside fine boots.  The monitor was given factory and seens the DVI connection but Windows remains empty. Also tried to start first with no cable - connect the DVI and the monitor remains in sleep - be able to reset the monitor and still a Virgin is also no connection DVO.

  I have fI switch with connected DVI I can get to the BIOS, and I see the HP logo and the points Win 8 starts.

  I don't know what else I can try.  I have no other usable with DVI video card

  Any ideas out there?

  Pls help - Steve

  Although I am an employee of HP, I speak for myself and not for HP.

  Yes, I rasthaus the monitor and cable of my older Compaq running xp and all fine on DVI.  The monitor and cable are fine.

  Since then, I've had a product in Australia specialist help.  Tried all the previous things, then initially went to check if the person had been doing the right thing - connected the VGA monitor with the supplied adapter DVI-d port - which has always worked well.

  Went to Device Manager o and removed the video card adapter. Powered off and then attached the monitor directly with DVI and it started late! Drviers reinstalled and updated and now I have nice crisp clear video appears.

  Something of the support person should apparently have - insead has asked me to wipe the hard drive and restore the factory system, replace the cables, buy a new monitor... was even asked to leave VGA mode and do not use DVI!

  Thank you for your help, Dave, its good to know that you are around to help us.

• Where are the front USB ports on the HP Envy Desktop 700-210?

  I bought the 700-210 office envy because he has so many USB ports.   However, I can only find 8-2 on top and 6 on the back.   According to the specifications, there are supposed to be some at the front.   I have to take something out to find them?

  Thank you.

  V.J.R.-Savannah, welcome to the forum.

  Here is the Product Specifications page for the computer.  If you look at the picture of the computer in the link, I think the cover under the red band to slide down to expose the USB ports.  This is how it works on my 810-135qe want.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• [SRP527w] Use the 4 Ethernet Port as a WAN Port?

  English:

  Hello world

  I just can't understand how to use the ethernet port 4 as a WAN port.

  I think it's possible because it labeled LAN/WAN at the rear of the unit... If someone can, please let me know how!

  Thank you for your help,

  Gaultier.

  English:

  Hi all

  I can't configure the 4 en world WAN ethernet port.

  It seems to me that this is possible since the port is called LAN/WAN on the device... If someone did it, thanks for that comment!

  Thank you for your help,

  Gaultier.

  Hi Gauliter,

  Please use the Administration > menu of switch setting.  Set the option Interface DSL for disable use 4 Port LAN instead of the ADSL interface.

  Note, this setting will factory reset the router and completely disable this ADSL interface.

  

  I hope this helps.

  Andy

• Force the VM to use the wired ethernet port instead of wireless

  Hello

  I use ver 9 workstation.  I have my host computer (win 7 64 bit) connected to our network of offices using the connection with wireless computers.

  I use a windows xp based virtual machine image that connects to devices of 3rd party via the ethernet port wired in Bridge mode.

  Is there a way to force the workstation on the use of only the cable connection and don't EVER try to connect via the wireless?

  At the moment I have to disable the wireless for the workstation to access cable port, if the without wire is activated, so you may not see anything on the wired port...

  It also causes headaches with ip address conflicts (3rd devices use the same IP range as our network of offices) if I don't have the VM running and wireless power.

  Any help or advice would be appreciated

  Tim

  Use the virtual network Editor to bind to the target adapter for VMnet0 and set the NIC of the virtual machine to use connected by a bridge.