Primary hard drive 1 not found

Similar Questions

• Primary hard drive 0 not found Dell Latitude

  Hello

  I just bought 2 notebooks of Dell Latitude D800 with no operating system. The first laptop is fine, but the second, when I turn it on it shows the Dell screen with the loading bar. The loading bar is to halfway to the end when it freezes. The system freezes on this screen for about a minute, then it beeps twice and a black screen that says:

  "First hard drive 0 not found '.

  No bootable devices - don't strike F1 to retry boot, F2 for Setup utility.

  So I go into the BIOS and see under "internal hard drive" and he says: 'no '. I checked and make sure the hard disk has been activated, and it is.

  I took the hard drive and reinstalled it. Nothing. The drive is a Toshiba 40 GB. In addition, mention, the reader makes a weird noise (not the click of death) and the hard drive on the laptop stays on all the time.

  Other D800 I mentioned boots very quickly and displays a no. OS screen, which is very good.

  So is my dead HDD?

  Thank you

  It is quite clear that the BIOS does not recognize the hard drive.  I suspect that the IDE controller on the motherboard has failed.

  Given that you have two cell phones similar to fool around with, probably the fastest way to isolate the problem is to swap hard drives.  Call the laptop that does not have one and one that works B

  If the laptop has now boots and cell B now is not, you know that the player who has been to A is bad.

  If A laptop computer still does not start and portable B boots again, then you know that the two disks are OK and the problem is the motherboard or the connector of the drive in the laptop.

• (brand new) hard drive 0 not found (Latitude D600)

  ======================================================

  I know this has been discussed a lot, but I have not found a solution.

  My laptop is a Dell Latitude D600, BIOS Version: A16

  My HARD drive died last week, he was making noises that I made backups.

  Of course, one morning I turned it on and it says '... ". hard drive 0 not found... »

  So I thought right we'll buy a new one, no big deal. In this case.

  But to my horror, the brand-spanking-new HARD drive made me exactly the same thing!

  Costs of the antistatic packaging, directly in the cradle, with tenderness.

  "First hard drive 0 not found '.

  No bootable devices - strike F1 to retry boot, F2 for Setup utility.

  Also, the BIOS reads my "main hard drive: ' as 'None '.

  I tried: -.

  -Replace (re-attachment for cradle clamp, tighten, etc..)

  -reset of the BIOS (pressing ALT - F)

  -internal 'HDD' isolation in the "boot order" (BIOS)

  -startup WinXP CD to format (says also that it cannot detect a HARD drive)

  -stroked and tweaked every possible BIOS setting

  -a ran the diagnostics (well Yes, tells me that it cannot find a HARD disk)

  -check the temperature (not a problem at all)

  I bought my D600 to opportunity without boot floppies or manuals, and private security has passed.

  I'll try to take out the battery for a day to see if that will be "flash BIOS" but I can't help you as (to my knowledge) the motherboard settings remain stored with the help of a small battery attached to the actual motherboard that would be inside the envelope, so I think it's a misunderstanding in another post on the forum , but I'll try it in desperation anyway. Next step would be to open the envelope and checking the IDE and remove the battery from the motherboard for 5-10 minutes.

  After that, my only option is to send to some local business PC repair. Ick.

  Any help will be VERY appreciated! Thank you.

  
  

• First hard drive 0 not found on Dell Windows XP computer

  Original title: Hard Drive not found

  I have a Dell Dimension 4550 Series computer using Windows XP SP3.  At startup the following message now "Primary Hard Disk Drive 0 not found".  Only the option F1 or F2 gives me or what appears to be a viable solution.  Impossible to access anything whatsoever beyond this screen.  All connections look OK.  Resolution ideas are welcome!  Thank you.

  Hi MartinL960,

   

  Remember to make changes before this problem?

  It is a hardware problem with Dell, through my research I found that users encounter similar problem solved the problem by making changes to hard disk parameters in the BIOS.

  Important: Change BIOS (Basic input output system) /semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Since the resolution requires the modification of the BIOS that is risky, I recommend you contact dell for more specialist on this question help

  Dell support

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&CS=19&l=en&s=DHS

• HP pavilion g4-1304au notebookpc - HARD drive is not found during the installation of Windows XP

  name of the product - hp pavilion g4-1304au notebookpc

  product no - #ACJ D4X79PC

  processor - AMD A4 - 3330 X

  During the installation of windows XP, it shows an error that the "mass storage is not recognized.

  Please give me Slipstreamer pilot for the specification above.

  You can follow the instructions in the following document, which allows you to install Windows XP on your laptop.

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=130&prodSeriesId=5046252&prodTypeId=321957&ObjectID=c01092639

  Also make sure that you install the last Windows XP SP3 for laptops and get into the BIOS and change a SATA AHCI to IDE / legacy mode.

  Also, if there is a parameter called "Secure Boot", disable it.

  I hope this helps.

• my computer says that my primary drive 1 not found, secondary drive 0 is not found. also allicating I/O bar for PCI device error.

  We had a power outage about 2 weeks ago, it burned my hard drive. My neighbor put a new disc in for me, now my computor is said primary drive 1 not found, O secondary drive not found, and 1 secondary drive not found. I do not know how to solve this problem, can you help me?

  Hi camicannon,

  Check out the wire link such question and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/XP-primary-hard-drive-disk-not-found/c98f8205-78d8-4e6a-A603-8c4fae852690

• HARD drive can be found on LX835-D3380

  Can anyone help? Went to switch pc on lx385-d3380 and all of a sudden, that is to say no drive found.

  Hello

  The HARD drive is recognized in the BIOS?
  Go to the BIOS by pressing F2. Usually the HARD drive should appear on the first page of the BIOS.
  If it is not listed, the HARD drive was not found by the BIOS... I suppose that because of HARD drive failure.

  In this case, the HARD drive should be replaced to solve the problem.

• At the start, receiving the message "Primary Drive 1" not found on Dell Dimension 2400 desktop

  Original title: primary drive 1 not found

  I'm helping a senior Windows user with a problem on his desktop Dell Dimension 2400.  At the start, he gets the message "Primary Drive 1" not found.  Can someone point me in the right direction as to what measures to take next?

  THX,

  Mike T goes.

  Hi Mike t. in Virginia

  You can check out the following link and try the steps suggested by Samhrutha G, Support Engineer, December 3, 2010 and check if this may help:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/primary-hard-disk-drive-1-not-found/fa3e591f-daeb-47bf-8f6f-3238f9507b6a

  Hope this information helps.

• Primary drive 1 not found after reinstalling original software

  Original title: startup

  I reinstalled my original software on my computer and now when I turn on my computer, it says: primary drive 1 not found.  The attention!  Active mode OS install.  Available memory limited to 256 MB.  Strike F1 key to continue, F2 to run the Setup utility.  What can I do to solve my problem?

  Hello

  I suggest you to follow the steps in this link and check if it helps:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/primary-hard-disk-drive-1-not-found/fa3e591f-daeb-47bf-8f6f-3238f9507b6a

  It will be useful.

• Primary drive 1 not found

  "I have a desktop computer Dimension 4600 series and whenever it starts I get the message" primary drive 1 not found. Press F1 to continue, F2 to run the configuration utility. If I hit F1 it will continue to boot from the HARD drive and everything works well. I'm running BIOS version A07 and am interested in upgrading to the latest (A12). I ran through the installation program and the hard drive is detected by the bios and the bootlist is set to floppy, cd, and then hard drive. Any suggestions from anyone?

  
  

• Whenever I restart my Dell 3000 I get this message: "primary drive 1 not found; Secondary drive 1 not found. »

  Whenever I restart my Dell 3000 I get this message: "primary drive 1 not found; Secondary drive 1 not found. "Then, I received instruction to hit F 1 to continue, which then takes me by the beginning upward. I get as both "F 2 = Set up" and "F 12 = Boot menu." The latter I have looked but frankly have no idea what to do or how it might solve my primary problem. What should I do to simply go through the commissioning by turning on my computer?
  GRDavis

  * original title - starting problem *.

  This isn't a problem of Windows XP. But take a look here:

  http://forums.CNET.com/7723-10149_102-162197.html

• Drive 0 not found error

  Original title: 4400 message stopped Dell system restart

  Help I can't get anything. I arrived at the diagnostic part and I had... .searching please wait

  Primary IDE

  Disk 0:

  What is c? I have no hard drive?

  Hi CDarga,
   
  Primary drive 0: not found error could be due to one of these reasons:
   
  (1) cables are not properly connected to the drive hard (or motherboard).
  (2) the hard drive is damaged and must be replaced.
  (3) basic Input Output System (BIOS) settings can be bad.

  NOTE: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

  Check these settings on your computer to solve the problem.

• Seagate 120 GB external HARD drive could not be detected

  We use Win XP Pro, when you plug the HDD of the promt "Cypress AT2LP RC42" System. How to detect this material?

  In the Device Manager Composite Device failed to start Code: 10

  Hello

  I think it might be 2 possibilities, why it does not work.
  First the external drive is dead and that is why it does not work or there is something wrong with the USB ports.
  Sometimes after installing SP2, the ports will not work.

  For this, I found this Microsoft Knowledge base article:
  http://support.Microsoft.com/?kbid=873169

  I think you should try to connect this USB HDD on another computer, make sure that the HARD drive is not altered.

  My brother uses a with USB cable external HARD disk that supports 2 USB connectors.
  This cable allows you to use the USB ports and dual power.
  I think that's not a bad idea, try using a USB hub with an external power supply and then connect the HDD to this hub.

  Eventually, it helps.

• New 500 GB HARD drive is not recognized correctly

  What is happening, I replaced the drive HARD than Go 150 original after about 18 months, again, now a year later, that the drive seems to have died too, so I bought a new seagate 500 GB drive HARD for it, the BIOS said it s it, but vista CD dies just when it is trying to install, CD WXP can t see the drive at all, but I expected that when WXP is older , but Vista I expected to work.

  So here's the thing, I put the new HARD drive in my desktop PC and he found in the BIOS no worries, then I started the Vista CD and again no probs, Vista installed without worries, then I put the HARD drive in the lappy and once again he can t read it, so it s not a Vista thing , it seems that it s the lappy itself

  Is this a problem with the Toshiba BIOS, or is it a physical problem where the Toshiba is struggling in reading ANY player?

  It s driving me crazy.

  And what model of laptop do you have?

  Generally upgrade HARD drive should not be a problem. I assume that your laptop's HARD drive with SATA interface and I sure you bought the right of Mr. I've upgraded or because of the experiences on several laptops equipped new hard disks and all of them were still properly recognized and I was able to install original Toshiba Recovery (recovery DVD) on this subject image.

  Maybe you have an older model A200 and perhaps he has some compatibility issues with new hard disks. I will be 100% sure works perfectly with HARD drive up to 300 or 400 GB maybe.

  Do you use Toshiba Recovery for the Vista installation disc or original disc of Microsoft?

  BTW: WXP is unclear due to lack of driver SATA HARD drive.

• Backup failed with error 18: the backup drive is not found

  Hello

  My guard time capsule saying "Backup failed" for a few days and I cannot access the old backup files either (when I enter my time machine it shows 'today', which is kind of scary, although I know that my old files is still there). I tried many ways to trouble shoot this problem, but none of this has worked. In my opinion, it's more a network problem and I made sure I connect Wi - Fi even my time capsule created.

  So far I have tried:

  -Delete the files from my internet (com.apple.airport.preferences.plist; preferences.plist and NetworkInterfaces.plist, etc.) and restart my mac

  -Remove TimeMachine.plist and restart my mac

  -Hard reset of my time capsule. Went through all configurations with success but then still backup missed (I hear the running time capsule when it is by train).

  I share this time capsule with my wife and she has no problem with that.

  I can only think of a possible alternation I did which could cause this problem.

  Because of unstable WiFi problem, I had deleted

  com Apple.Airport.Preferences.plist

  com.Apple.Network.identification.plist

  NetworkInterfaces.plist

  Preferences.plist

  or other files and reboot my mac * before * I had this problem with time capsule.

  However, this is not the first time I do it, and it wasn't a problem before...

  This could be the reason? If so, how to restore the network settings?

  Please help me with this problem. Really appreciate!

  Ted

  Here is a copy of the Console:

  24/02/16 2:44:19.308 AM com.apple.backupd [857]: from manual backup

  24/02/16 2:44:19.309 AM com.apple.backupd [857]: Destination Time machine could not be found (url: destinationID (null): AB78050D-4852-489D-9CBF-88727FBC8047)

  24/02/16 2:44:19.313 AM com.apple.backupd [857]: backup failed with error 18: the backup drive is not found.

  24/02/16 2:44:35.326 AM com.apple.backupd [857]: NAConnectToServerSync failed with the error: 64 (host is out of service) for url: afp://Ted%20Ling; AUTH=SRP@Flymi's%20AirPort%20Time%20Capsule._afpovertcp._tcp.l ALCO. / data

  24/02/16 2:45:29.976 AM com.apple.backupd [857]: attempt to mount the destination network URL: afp://Ted%20Ling; AUTH=SRP@Flymi's%20AirPort%20Time%20Capsule._afpovertcp._tcp.l ALCO. / data

  24/02/16 2:45:29.976 AM com.apple.backupd [857]: error - 35 during the resolution of the backup destination alias

  24/02/16 2:45:29.976 AM com.apple.backupd [857]: attempt to mount the destination network URL: afp://Ted%20Ling@TJ's%20AirPort%20Time%20Capsule._afpovertcp._tcp.local./Data

  24/02/16 2:45:30.668 AM com.apple.backupd [857]: destination network mounted at the mounting point: / Volumes/data using URL: afp://Ted%20Ling@TJ's%20AirPort%20Time%20Capsule._afpovertcp._tcp.local./Data

  24/02/16 2:45:50.428 AM com.apple.backupd [857]: impossible to eject the volume/Volumes/Data (FSVolumeRefNum:-111; status:-47; dissident pid: 0)

  24/02/16 2:45:50.428 AM com.apple.backupd [857]: wait 60 seconds and try again.

  24/02/16 2:45:59.981 AM com.apple.backupd [857]: NAConnectToServerSync failed with the error: 64 (host is out of service) for url: afp://Ted%20Ling; AUTH=SRP@Flymi's%20AirPort%20Time%20Capsule._afpovertcp._tcp.l ALCO. / data

  24/02/16 2:46:42.807 AM com.apple.backupd [857]: Timed out while solving Hello destination: afp://Ted%20Ling; AUTH=SRP@Flymi's%20AirPort%20Time%20Capsule._afpovertcp._tcp.l ALCO. / data

  24/02/16 2:46:42.812 AM com.apple.backupd [857]: from manual backup

  24/02/16 2:46:42.814 AM com.apple.backupd [857]: the airport of Destination Flymi Time Capsule could not be found (url: afp://Ted%20Ling;) AUTH=SRP@Flymi's%20AirPort%20Time%20Capsule._afpovertcp._tcp.l ALCO. (/ data destinationID: B2187361-58BC-4D33-A7AC-1DDC429ABF3B)

  24/02/16 2:46:42.825 AM com.apple.backupd [857]: backup failed with error 18: the backup drive is not found.

  24/02/16 2:46:42.833 AM com.apple.backupd [857]: from manual backup

  24/02/16 2:46:50.544 AM com.apple.backupd [857]: network destination already mounted to: / Volumes/data

  24/02/16 2:46:50.604 AM com.apple.backupd [857]: network destination already mounted to: / Volumes/data

  24/02/16 2:47:16.683 AM com.apple.backupd [857]: impossible to eject the volume/Volumes/Data (FSVolumeRefNum:-111; status:-47; dissident pid: 0)

  24/02/16 2:47:16.683 AM com.apple.backupd [857]: wait 60 seconds and try again.

  24/02/16 2:48:20.566 AM com.apple.backupd [857]: network destination already mounted to: / Volumes/data

  24/02/16 2:48:44.360 AM com.apple.backupd [857]: impossible to eject the volume/Volumes/Data (FSVolumeRefNum:-111; status:-47; dissident pid: 0)

  24/02/16 2:48:44.360 AM com.apple.backupd [857]: wait 60 seconds and try again.

  24/02/16 2:49:48.014 AM com.apple.backupd [857]: network destination already mounted to: / Volumes/data

  24/02/16 2:50:11.885 AM com.apple.backupd [857]: impossible to eject the volume/Volumes/Data (FSVolumeRefNum:-111; status:-47; dissident pid: 0)

  24/02/16 2:50:11.885 AM com.apple.backupd [857]: give up after 3 attempts.

  24/02/16 2:50:11.903 AM com.apple.backupd [857]: backup failed with error 21:21

  24/02/16 2:50:27.245 AM com.apple.backupd [857]: impossible to eject the volume/Volumes/Data (FSVolumeRefNum:-111; status:-47; dissident pid: 0)

  24/02/16 2:50:27.250 AM com.apple.backupd [857]: from manual backup

  24/02/16 2:50:27.250 AM com.apple.backupd [857]: Destination Time machine could not be found (url: destinationID (null): AB78050D-4852-489D-9CBF-88727FBC8047)

  24/02/16 2:50:27.257 AM com.apple.backupd [857]: backup failed with error 18: the backup drive is not found.

  24/02/16 2:52:28.390 AM SystemUIServer [265]: try using XPC with a MachService which has the value HideUntilCheckIn. This will result in unpredictable behavior: com.apple.backupd.status.xpc

  24/02/16 2:52:28.390 AM com.apple.prefs.backup.remoteservice [866]: try using XPC with a MachService which has the value HideUntilCheckIn. This will result in unpredictable behavior: com.apple.backupd.status.xpc

  What model is the TC?

  Try to force the connection to 2.4 ghz using different names for the various bands... or even better to use ethernet.

  (You may need to buy love at first sight for adapter Ethernet... is an investment worth considering how unreliable wireless).

  Also give me some screenshots of the TC installing airport utility.

  Can you get it in the Finder?