Printer C6180

Similar Questions

• Reset the printer c6180

  I have a c6180 sometimes I switch off at night using power button.  Normally it turns on fine.  Today, I got the message that I need to use power button and not disconnect or turn off band (which I never do).  The machine guard re-boot during the start cycle.  I tried to push #-6 while plugging the unit, such as suggested by the other post.  It seemed to work when you turn on the printer, but when I tried to print it kept recycling through start cycle.  All of the suggestions.

  Rich

  I'm afraid that the printer can be fried. You can try the steps outlined in the document below. If those who do not help, try to do a hard reset. If this does not work, try to do a partial reset. If none of this does not work, you will need to replace the printer.

  The HP printer power on not or answer:
  http://goo.GL/QBeRH

  To do a hard reset:
  1. make sure that the printer is turned on.
  2. pull on the power cord from the printer.
  3. pull out the power cord from the wall.
  4. wait for 30 seconds.
  5. plug in the printer and turn it on.

  To make a partial reset:
  1. make sure that the printer is turned on.
  2. pull on the power cord from the printer.
  3. pull out the power cord from the wall.
  4. wait for 30 seconds.
  5 connect the power supply cord inot the wall, but do not connect the printer.
  6. press 3 and # buttons.
  7. while now buttons, plug in the printer.
  8. when the lights come on, release the buttons.

• Reset the printer C6180 for different regions cartridge

  I recently moved to the United Kingdom in New Zealand. My C6180 is configured for cartridges 363 series available in the United Kingdom. The same cartridge is 02 series in New Zealand, and when I install the printer tells me that the printer is not configured for this cartridge. I think I have to reset the printer to a different area, so two questions.

  1. How can I do this and if I need to call HP where can I find the number?

  2. I guess I can't mix cartidge types so will have to replace all of them, correct?

  Thank you

  B

  1 make sure you buy set of inks that are compatible in New Zealand and make sure that SW has been installed on your computer.

  2. Please call technical assistance from HP - 0800-441-177 for more information.

• are there any current HP printers that use the HP 02 print cartridges? Old printer C6180 goes wrong.

  are there any current HP printers that use the HP 02 print cartridges? Old Photosmart C6180 printer goes wrong and have a lot of cartridges.

  The Site of HP Pageyield lists the following printers compatible with 02 cartridges:

  • " HP Photosmart 8200 printer
  • " Printer HP Photosmart D7100
  • " Printer HP Photosmart D7200
  • " Printer HP Photosmart D7300
  • " Printer HP Photosmart D7400
  • " All-in-one HP Photosmart 3100 Series
  • " HP Photosmart 3200 all-in-one series
  • " All-in-one HP Photosmart 3300 series
  • " HP Photosmart C5100 all-in-one series
  • " HP Photosmart C6100 all-in-one series
  • " HP Photosmart C6200 all-in-one series
  • " HP Photosmart C7100 all-in-one series
  • " HP Photosmart C7200 all-in-One series
  • " HP Photosmart C8100 all-in-one series

  I do not believe there are all the models currently available that use cartridge 02.

  I heard that HP has (had?) a trade-in program for its intact packaging expired cartridges.  See this post for a suggestion.

• HP c6180 printer: wrong cartridge on c6180

  I have HP printer c6180 and I put new cartridges and now it says "wrong cartridge". What can I do to solve my problem

  Hello @Yasss and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you have problems with the cartridge.  I would like to help!

  I recommended to remove cartridges from the printer and starting by a power reset.   Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I would also recommend following the steps outlined in this document:

  The "Unjust of the ink cartridges installed" Message appears on the screen color graphics

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• PhotoSmart C6180: page c6100 is broken

  I am trying to download a driver for my printer C6180, but all roads lead to this page:

  http://support.HP.com/us-en/product/HP-Photosmart-C6100-all-in-one-printer-series/1153695/model/1153...

  This page is empty.  Is there another page?

  Hi @eTTguy,

  Welcome to the HP Support forums.

  I understand that you try to download the drivers for a HP Photosmart C6180 all-in-One Printer for Windows 10 but cannot because the tracking link opens a blank page. I want to help you with that.

  I am currently on a Windows 7 PC using Internet Explorer and Google Chrome, and the link you posted took me to the support home page for the HP Photosmart C6180 where you would still need to click on "Software & drivers" and the blue "go" button under "Option 2" to get the drivers HP Photosmart C6180.

  If you follow this link, so that it brings you directly to the page software and drivers with a red download button click on start download - drivers and software HP Photosmart full feature.

  This link should work. If she opens another blank page, try a different web browser. Web browsers Act sometimes differently with different websites.

  Please let me know if that solves the problem, or if you need assistance.

  In fact, if it helps you to find a solution, please click on the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• ICC profile is no longer installed

  All-in-One printer C6180, HP computer HP Desktop Pavilion P6000 Series, model P6710f, Windows 7 Professional 64 bit 6.1 (Build 7601) Service Pack.

  Error (CCI profile is no longer installed)

  I received error messages related to the HP Solutions software.  I've uninstalled and reinstalled the software downloaded from HP.  I didn't see no problem after installation, until I went to print an image in Adobe Elements 9, when I received an error: could not print because the ICC profile is no longer installed.  I first thought that the problem may have been related to the Adobe program so I uninstalled and reinstalled only to get the same error message.  Reading the information from Adobe on this problem, suggested the problem may be in the printer software.  I went to HP print and Scan doctor, is through the uninstallation and reinstallation of the AIO software and Solution Center software.  Checking the installation with doctor Scan once again, he said that a later version of the software is available, and whenever I try to download the latest version, apparently he won't take that after whenever I do that, I get the same page telling me that there is a newer version available.   When I skip this step and go to the test printer, everything also checks good.  I also went to a backup of my dll software, for the previous month, nothing helps.

  I am for a quandry here about the absent ICC profile and hope that someone else has had this problem and a solution.  I've not found anything when I did a search on this forum.

  Hello @JoeSea,

  I understand that you encounter the error "could not print because the ICC profile is no longer installed. As this is an error with Adobe I would advise you to ask for help on the General Adobe Photoshop Discussion Forum that you would have a better chance to find a solution.

  I hope this helps. Thanks for posting on the HP Forums. Have a great day!

• You have one (0xc) ink SYSTEM FAILURE error message?

  OK, I have an old printer (C6180 (Yes this old)) I had to put in stock for a long overseas military tour.  When I finally returned, I swapped the ink cartridges and get an error code of 0Xc18a0406.  It is not a removable print head, so I am at a loss to try to clean it.  Any suggestion or help would be appreciated.

  I wil send you a private message to something else, you can try.

• HP Photosmart C6180 Magenta Ink not printing

  error message: no

  description of the problem: Magenta Ink not print not EXCEPT on the page that prints after aligning the print cartridge printing is performed. At the bottom of this page, the bars of yellow, Cyan and Magenta print perfectly, just like the mixture of the color shown in the colorful bird printed below the bars.

  Self Test Diagnostic Page is printed with bars No. Light Magenta or Magenta, under print quality model. State of ink and level for both shows like OK magenta and 100%

  Troubleshooting: I ran repeated cycles of head cleaning and aligning the print cartridge print without changing the output. The page that prints after cleaning has NO magenta bars or lines. Seems the page that prints after alignment. Via e-mail support, I was directed to perform a complete reset "semi" and "the NVM reset" - neither of these had no effect. Magenta inks have been replaced, but the problem persists.

  Exchange: the printer had not been used for several months.

  My printer started working. It had been disconnected and sitting for several months. I turned it to try the HP solutions (below) and found that it worked - I had nothing to do!  In any case, I hope this can help some of you with similar problems:

  Hello
  
  Thank you for contacting HP Total Care.
  
  I'm Vivian of HP Total care for all-in-One products, and this response is in what regards the problem with HP Photosmart C6180 all-in-One Printer.
  
  Of your mail, I understand you have a HP Photosmart C6180 all-in-One Printer. Currently, you have a problem in which the printer prints in magenta only on the alignment page and not even on the test page.
  
  I am aware of the importance of the issue and will give you the appropriate information. I need your cooperation and appreciate your efforts to resolve the issue.
  
  First of all I want to thank you for the link, I'll take that as a feedback and will forward it to the concerned Department. However it is not a known, issue because in this case, HP will take immediate action and make sure that defective cartridges do not reach the market.
  
  Please try the following troubleshooting steps. I assure you that those measures would solve the problem.
  
  I ask you to check if you have the same problem with the copy as function. If the printer copy very well magenta do not perform one of the steps given and please get back to us for further assistance. However if you encounter the same problem with the copy as well please continue with the provided steps.
  
  First step: clean the copper contacts.
  
  (1) take a lint cloth or a cotton ball, it wet with water.
  (2) clean the cartridge copper contacts.
  (3) you have the same type of copper on the printer also, contacts if you are able to reach their own contacts in copper on the printer also.
  (4) reinstall the cartridge in its housing.
  (5) when the printer is on, unplug the power cord from the printer.
  (6) press and hold the power button for about 30 seconds.
  (7) re plug the power cord into the printer and the printer.
  
  If the problem persists, proceed to the next step.
  
  Step 2: Perform a drain of power on the printer.
  
  (1) remove the power cord from the product
  (2) press and hold the power button for about a minute (while the power cord is not connected to the printer).
  (3) release the button.
  (4) connect the power cord to the product
  (5) use the button to turn the product on.
  
  Connect the printer to the computer and check; If the problem persists, proceed to the next step.
  
  Step 3: Reset the printer to the factory settings.
  
  (1) use the button to turn the product on.
  (2) remove the power cord from the product
  (3) press and hold the # and 6 buttons.
  (4) while now buttons, plug the power cord to the product
  (5) to continue to press the buttons for about 30 seconds.
  (6) use the button to turn the product on.
  (7) if these steps do not resolve the problem, it will be a hardware problem with the printer in this case I suggest you take the printer to the nearest authorized Service Provider for the service.
  
  Please follow these steps and get back to us with the results, if you need more help, please reply to this message and we will be happy to help you further.
  
  We look forward to hear from you.
  
  For more information on keep your HP and Compaq products up and running, please visit our Web site at:
  
  http://www.HP.com/go/TotalCare

  ALSO:

  If the printer performs the color copy and you get magenta on the copy, it is obvious that the printer works fine, it's a software problem. I ask you to try the following steps, depending on your convenience and get back to us with the results.
  
  First step: reset the printing system
  
  To use the reset printing system feature, follow these steps:
  
  1. in the Finder, choose utilities from the menu reach.
  2. open the printer setup utility.
  3. in the printer setup utility menu, choose Reset Printing System.
  4. click on reset.
  
  Second step: check/repair disk permissions
  
  Click on Go tab in the top menu bar.
  Select the utilities tab.
  Click disk utility.
  Once disk utility appears, select the drive and click the check permissions.
  
  This can take a long time to complete as the Mac will try to check all permissions to the hard drive.
  Now click on the tab authorization to repair disc.
  
  This can take a long time to complete as the Mac will try to repair all permissions to the hard drive.
  Once Permission to disk check is complete, restart the Mac
  
  Step 3: Add the printer again
  
  1. click the Apple on the top of the left hand button.
  2. click on Preferences system, window system preferences will open.
  3. click on the printers and faxes icon.
  4. click on add the symbol on the bottom of the left hand.
  5. you see your printer in the list, select it and click Add on the right side.
  
  Please, do the following and get home with the results, for further assistance please get back to us, we will be happy to help you.
  For more information on keep your HP and Compaq products up and running, please visit our Web site
  to:
  http://www.HP.com/go/TotalCare

• C6180 scan works very well from the printer to the pc, but hp solution center gives error 4, [(3,42,0)]

  Photosmart C6180 wireless unit connected to your PC running windows 7 64-bit ultimate.

  Scan worked fine but after some update (I have not seen that and when) stopped scan from the hp Solution Center. It gives an error 4, [(3,42,0)].

  If I scan directly from the printer, it works fine, even if I send the jpg for the PC images\Mes traverses the directory.

  I already deleted the hp Solution Center and reinstall it using AIO_cda_FSW_Full_Win_WW_130_140.exe

  Thank you

  hasksm

  Hi there hanksm,

  I'm sorry to hear about your problems with your Photosmart C6180 and Windows 7 scan and notice you receive the error code. I studied the error and found a position with a person with a 'Solution', so hopefully this will help your situation.

  Please see JasonBlake7 post: scanning error

  Please let me know how it goes and if you need help!

  Thank you

• Cannot print in black C6180

  My C6180 printer all-in-one just stopped printing in black. I changed the cartridge of the printer 3 times and it made no difference? It prints in color but not black. I cleaned the cartridges and that did not help. I noticed on some other forums that other people have the same problem without finding a resolution.  Anyone got any suggestions?

  Well, I might have some hope. Actually, we have found a solution to this problem and our printer now works as usual. I'll try to explain what we were doing, so I hope it helps someone else. I must say that I was chatting online with a HP technician at least an hour and it never recommended this solution, and we found it on their help page. Maybe he did know about this!

  First, you will need to access the Toolbox of printer on your computer. Go to start-programs-HP-HP Solution Center.

  Select settings

  In the drop-down list, select the printer settings

  Select printer Toolbox

  In respect of peripheral Services, select the option for clean print heads

  It's a clean deeper than what is being done to the printer itself. We ran this about 5 times, and at the end of this it was printing black again. It was a few months ago and we have not had a problem since.

  I hope it helps someone else. HP did not of course help us!

• If I only print in black why my HP Photosmart C6180 uses up color cartirges? Are expensive!

  If I only print in black why my HP Photosmart C6180 uses up color cartirges? Are expensive!

  Hello

  All printers do the same thing that even many printers have an option to print in black INK ONLY. The reason: during the process of global warming, printers need to use all inks to check and maintain their print heads... Some people say, we turn on the printer / OFF it will use more ink, I can't confirm that but understandable.

  Kind regards.

• Photosmart C610: Black Photosmart C6180 print does not correctly

  My HP Photosmart C6180 is not print black properly. I just made impression after he hada problem with ink xs18a0106. When I ran self test 2 times the black came out faded and veiny however the colors came out fine. Any ideas on how to solve this problem that I need to use black ink and color ink

  Here are a few guides I found on printing photos:

  1. If you are on a Mac: HP printers - print Photos (OS X)
  2. If you are running a Windows operating system: HP printers - print Photos (Windows)
  3. User Manual: user manual

• Print Macbook Pro w/Lion to a HP C6180 wireless and software says not connected printer.

  I am able to scan from the c6180 using the Apple Preview software...   I have a G4 Pro w/leopard onMacbook - NO problems...  I also have an older w of 4 months of iMac/Lion - NO problem (Note: the HP software from an iMac G5 w / leopard.)  Later, I downloaded from HP.com the full suite of HP software... This works.   It still works after software update Apple provide an update of the hp software) I'm comtenplating migration of new Macbook Pro iMac to see if it works.

  I tried power down the printer and re-startup - still no go...   Any suggestions or workarounds?

  Download and install this: http://support.apple.com/kb/DL907

  Restart your Mac.

  Reset the printing system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• Why my HP Desktop Vista keep delete my C6180 printer drivers?

  My HP desktop computer continually removes my drivers PhotoSmart C6180.  I visit the Web site and reload.  Then, he continually tells me that it cannot find PhotoSmart Essentials.  It asks me to insert my disc, but it is for XP and will not work.

  Hi brown7373,

  You have extracted the software even 4 times if you have 4 files 7z. Please try again with the instructions below.

  First step: clear temp directory

  1. Type %temp% term or search programs and files of field
  2. Select all the files in this folder, and then press the delete key to remove. If you receive a message that the file is in use, you will need to ignore this file (s).
  3. Proceed to step 2 below

  Second step: downloaded and extracted to your system:

  1. make sure to remove all previous downloads and then download full feature software and drivers of my link below to make sure and get a good installation.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-47461-2&cc=us&DLC=en&LC=en&... =

  2. once the download is complete, double-click the file to extract the software.

  3. when the installation window opens, press the Cancel button to stop the installation

  4. type % temp % in the race or search programs and files of field

  5 find the starting with 7z folder (example: 7zS2356)

  6. right click on the folder and select copy

  7. close this window and all windows open, then in the Middle Office right click your mouse and select Paste. This will move the 7z folder on your desktop.

  8 open the 7z, that you just copied on your desktop

  9 open the Util folder

  10 open the CCC folder

  11. start the L4uninstall.exe

  12. once the uninstall is complete, restart the computer

  13. run disk cleanup from the tools Accessories\ system under all programs folder

  14. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  15 open the 7z folder and then double-click the Setup.exe file that will be towards the bottom of the open window. Follow the instructions on the screen to reinstall your printer.

  Let me know if you are able to successfully install the software and driver and are able to print & scan?