PhotoSmart C6180: page c6100 is broken

Similar Questions

• HP Photosmart C6180 Magenta Ink not printing

  error message: no

  description of the problem: Magenta Ink not print not EXCEPT on the page that prints after aligning the print cartridge printing is performed. At the bottom of this page, the bars of yellow, Cyan and Magenta print perfectly, just like the mixture of the color shown in the colorful bird printed below the bars.

  Self Test Diagnostic Page is printed with bars No. Light Magenta or Magenta, under print quality model. State of ink and level for both shows like OK magenta and 100%

  Troubleshooting: I ran repeated cycles of head cleaning and aligning the print cartridge print without changing the output. The page that prints after cleaning has NO magenta bars or lines. Seems the page that prints after alignment. Via e-mail support, I was directed to perform a complete reset "semi" and "the NVM reset" - neither of these had no effect. Magenta inks have been replaced, but the problem persists.

  Exchange: the printer had not been used for several months.

  My printer started working. It had been disconnected and sitting for several months. I turned it to try the HP solutions (below) and found that it worked - I had nothing to do!  In any case, I hope this can help some of you with similar problems:

  Hello
  
  Thank you for contacting HP Total Care.
  
  I'm Vivian of HP Total care for all-in-One products, and this response is in what regards the problem with HP Photosmart C6180 all-in-One Printer.
  
  Of your mail, I understand you have a HP Photosmart C6180 all-in-One Printer. Currently, you have a problem in which the printer prints in magenta only on the alignment page and not even on the test page.
  
  I am aware of the importance of the issue and will give you the appropriate information. I need your cooperation and appreciate your efforts to resolve the issue.
  
  First of all I want to thank you for the link, I'll take that as a feedback and will forward it to the concerned Department. However it is not a known, issue because in this case, HP will take immediate action and make sure that defective cartridges do not reach the market.
  
  Please try the following troubleshooting steps. I assure you that those measures would solve the problem.
  
  I ask you to check if you have the same problem with the copy as function. If the printer copy very well magenta do not perform one of the steps given and please get back to us for further assistance. However if you encounter the same problem with the copy as well please continue with the provided steps.
  
  First step: clean the copper contacts.
  
  (1) take a lint cloth or a cotton ball, it wet with water.
  (2) clean the cartridge copper contacts.
  (3) you have the same type of copper on the printer also, contacts if you are able to reach their own contacts in copper on the printer also.
  (4) reinstall the cartridge in its housing.
  (5) when the printer is on, unplug the power cord from the printer.
  (6) press and hold the power button for about 30 seconds.
  (7) re plug the power cord into the printer and the printer.
  
  If the problem persists, proceed to the next step.
  
  Step 2: Perform a drain of power on the printer.
  
  (1) remove the power cord from the product
  (2) press and hold the power button for about a minute (while the power cord is not connected to the printer).
  (3) release the button.
  (4) connect the power cord to the product
  (5) use the button to turn the product on.
  
  Connect the printer to the computer and check; If the problem persists, proceed to the next step.
  
  Step 3: Reset the printer to the factory settings.
  
  (1) use the button to turn the product on.
  (2) remove the power cord from the product
  (3) press and hold the # and 6 buttons.
  (4) while now buttons, plug the power cord to the product
  (5) to continue to press the buttons for about 30 seconds.
  (6) use the button to turn the product on.
  (7) if these steps do not resolve the problem, it will be a hardware problem with the printer in this case I suggest you take the printer to the nearest authorized Service Provider for the service.
  
  Please follow these steps and get back to us with the results, if you need more help, please reply to this message and we will be happy to help you further.
  
  We look forward to hear from you.
  
  For more information on keep your HP and Compaq products up and running, please visit our Web site at:
  
  http://www.HP.com/go/TotalCare

  ALSO:

  If the printer performs the color copy and you get magenta on the copy, it is obvious that the printer works fine, it's a software problem. I ask you to try the following steps, depending on your convenience and get back to us with the results.
  
  First step: reset the printing system
  
  To use the reset printing system feature, follow these steps:
  
  1. in the Finder, choose utilities from the menu reach.
  2. open the printer setup utility.
  3. in the printer setup utility menu, choose Reset Printing System.
  4. click on reset.
  
  Second step: check/repair disk permissions
  
  Click on Go tab in the top menu bar.
  Select the utilities tab.
  Click disk utility.
  Once disk utility appears, select the drive and click the check permissions.
  
  This can take a long time to complete as the Mac will try to check all permissions to the hard drive.
  Now click on the tab authorization to repair disc.
  
  This can take a long time to complete as the Mac will try to repair all permissions to the hard drive.
  Once Permission to disk check is complete, restart the Mac
  
  Step 3: Add the printer again
  
  1. click the Apple on the top of the left hand button.
  2. click on Preferences system, window system preferences will open.
  3. click on the printers and faxes icon.
  4. click on add the symbol on the bottom of the left hand.
  5. you see your printer in the list, select it and click Add on the right side.
  
  Please, do the following and get home with the results, for further assistance please get back to us, we will be happy to help you.
  For more information on keep your HP and Compaq products up and running, please visit our Web site
  to:
  http://www.HP.com/go/TotalCare

• Helps the Photosmart C6180 Snow Leopard screen

  I install Photosmart C6180 all-in-One on my Mac using Mac OS X 10.6 Snow Leopard.   I want to access using Mac HP Photosmart for details on its use, but I can not find this file.  In the folder applications folder Hewlett-Packard includes HP Scan, uninstall HP, HP utility and utility peripheral files and licenses. The way I understand it is to use the Apple Software Update instead of using the software (CD) that came with the all-in-one.  I used the Apple software update. The CD that came with the all-in-one is the version 7.8.0.  I am out of the help file or I misunderstood the instructions and I already have all the files?  If so how do I access the folder help?

  Thank you.

  If you are using Snow Leopard, Lion or Mountain Lion and have HP software for Snow Leopard before (either from a CD that is not marked as compatible with 10.6-10,8 or you recently upgraded to Snow Leopard, Lion or Mountain Lion and had the software HP on your Mac before you upgrade - even if you made a standard uninstall of the old software or installed new software on top of it) You must uninstall the software by using the "scrubber":

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Press and hold Ctrl + Alt + Cmd keys on the keyboard at the same time as you click on uninstall< this="" is="" the="" scrubber="" option,="" there="" is="" no="" button="" labeled="">
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Download and install this: http://support.apple.com/kb/DL907

  Restart your Mac.
  Now reset the printing system:

  -Sys Prefs, Print & Fax
  -Right (control) click inside the box that lists your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!

  Finally, download and install the latest software for your printer from the "Support & drivers" link at the top of this page.

• Photosmart C6180 will not print

  I have a HP Photosmart C6180, running on a Windows XP computer.  Can I print the pages of test from the printer itself, but I get the following error when I try to print from my PC-"cannot print document."

  I have replacted cartridges Cyan and Magenta because for them, I was getting a low ink warning.  Three other cartridges have a 04-09-2009 expiration date.

  The printer refuses to print if the ink cartridges are after their expiry date?  If this is not the case, how can I solve the problem?

  Another note on the self test diagnostic impression, new cartridges Cyan and Magenta appear complete respectively 63% and 72%.  Should not say 100 percent because they have been installed just today?

  If you want something done...

  It took me a few hours because I had no reason to suspect, but it turns out that the problem is that the IP Address of my printer had changed.  I was to check the parameters of the port and noticed the URL does not match what was printed on the network configuration page that I had printed.  I chanted the URL in the port settings and retried the print a test page.  It worked.  Problem solved.  Thank you, me.

• Photosmart C6180 repeatedly loses the wireless connection

  Hello

  I have a mixed network of linux and windows PC as a Photosmart C6180 wireless access via a Netgear (DG834GT) wireless router.

  It works very well for over a year, but recently the printer keeps dropping the network.

  Show all PC (linux and windows) as offline and the router says that this isn't one of the connected devices, and I can't ping it.

  However, if I look at the State of the network on the front panel, it says which is plugged, and if I print the network status page it shows the active connection, wireless and watch as loan.

  This isn't a DHCP problem. The printer and all PCs have static IP address settings.

  If I change the printer market once again, it connects to the network, everything is OK and I can print, but a few minutes later it disconnects again.

  For now, I'll have to pass it works whenever I feel - please help!

  Thank you

  JohnT

  Hello

  Thanks for your suggestions.

  It seems it might be a problem with netgear!

  I rolled power the router netgear (normally on the left) and the problem seems to have disappeared.

  Thanks for your help.

  Concerning

  JohnT

• HP Photosmart C6180 with abnormal shutdown Message

  My HP Photosmart C6180 began to make a loop of continuous restart with error of abnormal termination. I've now tried # and 6 at startup to do a reset, but that only solves the problem for about 30 minutes.

  I read on other forums on the internet that this is due to faulty capacitor anyone else managed to solve this problem?

  I notice seven other users seem to have this problem on the forum.

  TTL79 wrote:
  

  I have the same problem. Is it possible to fix once and for all?

  Hi, yes I managed to fix my printer and it is working normally again! However, it is a bit complex - I had to remove the circuit board and replace the capacitors. I put the instructions on this site below as a method step by step for fixing.

  http://www.roshgaind.com/?p=200

  You will need to have a soldering iron, torx screwdriver and buy new capacitors. The whole process takes about 1 to 2 hours, I had limited experience with soldering, but I am familiar with disassemble computers.

  Attempt at your own risk - soldering irons are very hot and can cause injury if not done properly this can permanently damage your printer If in doubt ask a service center to fix your printer or buy a new one.

• HP Photosmart C6180: hp photosmart c 6180 turns off when it is connected to the network and blinks green photo

  When my Photosmart C6180 is related to two wireless and ethernet network after any number of hours it stops itself down and the green light on the front panel by the icon of camera flashes.  You will then have to push the power button to turn back.  Not very practical for a network printer. Router is a Linksys WRT 1900 ACS.

  Hi wjabdella,

  Thank you for your answer!

  In the post I provided on the hard reset, he mentioned: sometimes, when plugged into a surge protector or battery backup, the quantity of electricity is not received by the printer.  Power problems can cause printing problems.  It is particularly important to be plugged directly into a wall outlet with wireless connectivity problems, "sleep mode" and other power problems.

  So by unplugging the power and waiting, it resets the printer almost to its original state without making a complete factory reset and lose any other information.

  Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I hope that answers your question!

• If I only print in black why my HP Photosmart C6180 uses up color cartirges? Are expensive!

  If I only print in black why my HP Photosmart C6180 uses up color cartirges? Are expensive!

  Hello

  All printers do the same thing that even many printers have an option to print in black INK ONLY. The reason: during the process of global warming, printers need to use all inks to check and maintain their print heads... Some people say, we turn on the printer / OFF it will use more ink, I can't confirm that but understandable.

  Kind regards.

• Photosmart C610: Black Photosmart C6180 print does not correctly

  My HP Photosmart C6180 is not print black properly. I just made impression after he hada problem with ink xs18a0106. When I ran self test 2 times the black came out faded and veiny however the colors came out fine. Any ideas on how to solve this problem that I need to use black ink and color ink

  Here are a few guides I found on printing photos:

  1. If you are on a Mac: HP printers - print Photos (OS X)
  2. If you are running a Windows operating system: HP printers - print Photos (Windows)
  3. User Manual: user manual

• Power problem: Photosmart C6180

  My printer Photosmart C6180 continually lights stays on for about 30 seconds and then seems to lose power.

  I tried the troubleshooting steps already using different points of sale and unplug power for a period of time, but nothing has solved this problem.

  Someone know if it sounds like a problem with the printer or is there something wrong with the power supply?

  The printer was working fine a few days ago, nothing happened that may have caused damage that I know.

  Thanks for any help you can offer!

  Sorry, I should have searched the forum more carefully before posting, I found the solution to my problem.

• PriI impossible cannot print in color on my HP Photosmart C6180 all-in-One Printer.

  I can't print in color on my HP Photosmart C6180 all-in-One Printer.  I was not able to find the color preferences in the printer dialog box.  Any help?

  Try to uninstall and reinstall the software and drivers and see if it works for you.

• Photosmart C6180 - unable to delete the document in the print queue

  My Photosmart C6180 shows a document in the queue which can not be removed causing the error message and unable to print documents from my laptop.

  Hi Thomastwhilaker,

  I'd love to help you remove the paper that is stuck in your queue and get you print again.

  First post please returns with the answers to these questions.

  1. Is the printer connected wirelessly or with a USB cable?
  2. The printer is connected directly to a wall outlet or a surge protector? (It is preferable to connect directly on the wall)
  3. You have all other printers HP installed on this computer? If so, do you still have the printers?
  4. Is this a HP laptop or another brand?
  5. What operating system do you have? Mac or Windows?

  At this point because you said your 'portable' I imagine you have Windows. If you have not already tried the HP print and Scan doctor, please do and let me know the results. You will see a key, a yellow exclamation point, a red X, or a checkbox then each point tested. If you have a Mac, skip the following steps and let me know.

  

  Click here to download and run the utility > HP print and Scan Doctor

  If the problem persists, I suspect that if restart us the spooler, remove the driver and re - add the printer that we may be able to correct the problem. Follow the instructions below to perform these tasks.

  Restart the print spooler

  Hold down the Windows Logo key () on the keyboard and the 'R' to open the Run dialog box

  • Type services.msc and press enter
  • Locate the print spooler and double-click it to open the spooler properties
  • Make sure you that Startup type is set to automatic, if not please click the menu down and select automatic
  • Under Service status, please stop the server, wait a moment, and then click Start

  Remove the printer from the server to the printer properties

  1. open the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8 and 8.1 - Select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If you get an error "in use", restart the computer and the printer, and then follow the steps again.

  Re-add a printer

  Open start > all programs > HP folder > folder printer > HP Setup and the software if you do not see the program installation and software, but you see the printer icon, double-click the printer icon to start the installation and the software.

  Please let me know if this does not resolve the problem, or if you need additional help, I'm happy to help you.

• printer all-in-one memory card error Photosmart C6180

  Photosmart C6180 all-in-one printer, xp computer

  When I insert a 4 GB SDHC card in the SD slot + printer and

  When I insert a SDHC 16 GB card in the SD slot +, two cases, the error "memory card error" appears on the printer screen.

  The HP digital imaging monitor displays the error "no images on the card.

  How can I correct the mistake of the printer software.

  Hello

  No, it isn't, when the device was built there were that many more 1 GB card and they were still quite expensive.

• I have a hp photosmart c6180 all in one. for these last days, it does not switch. ins

  I have a HP Photosmart C6180 All in one.  For these last days, it does not switch. When I insert colored part of the cable into the printer then led on the cable is cut, that's why the printer does not illuminate.  Please let me know what could be the problem.  I thought that the cable may be defective, so I bought a new cable, but the printer does not work.

  Hi rajeshgaur,

  You can call our support lines to check if the printer can be repaired and how much he would run to fix the unit. The other option you have is to contact support and check in the trade trade program.

• Remove the dust under the glass of Photosmart C6180

  I have too much dust under the glass of my Photosmart C6180 and makes ugly scan.

  Is there a good method of-it-yourself?

  Thank you

  Rick

  Hello Rick6T-

  Really, there is no easy way to do it. I disassemble a similar printer and there are a lot of parts. If you try, take before photos and keep all the screws sorted.