Problem of two Casding Lov

Similar Questions

• How I fixed my USB ports not working not problem. Two ports left side previously does not... HP Dv7

  So I do not know what is not "where it will honestly, but put there just to try to help someone else who has struggled with this as long as I did it...» I ended up having my two USB ports on the left side (turned out to be my 3.0 ports) working again when they recognize nothing. I could use the USB 2 on right 2.0 ports, but the transfer rate was terrible.

  My answer on another question where someone had a similar problem... good luck!

  'Hi. '

  Not sure if this will help, but I had the same problem, the two ports on the left did not work on my Dv7. All this time I thought that the USB on the right were my 3.0 ports so I thought that would be nice, but it's been over a year that I initially had this problem and made a bunch of maintenance of the system meant that I would look through it again. In any case, I went to the Device Manager through the computer management tool. I know that you can go straight to the Device Manager, but just give you exactly how I did it. You can search just to start computer management.

  So I chose Device Manager in the menu on the left side and it looked like ordinary Device Manager. Went down to Universal Serial bus controllers... at this stage, I watched the action menu on the right and select more actions, opinions and you click Show hidden devices. After that I went through my USB controllers one by one as I had done many times before and checked them, tried the update of drivers, etc... Under the USB controllers Section, I noticed something like xHCI Host controller of compliance Test... I right click it and went into its details, I tried the driver updated and installed the new driver. 2 new USB controllers immediately arises: Renesas Electronics USB 3.0 Host Controller and root hub.

  Switched on a test drive from the right thumb to the left and the computer instantly recognized and installed the driver for the stick.

  And that was all... hope it helps even if this is later. "

  Hi @klark1kent,.

  Thank you for visiting the Forums Support HP's, welcome and thank you for the important information.

  Have a good week.

  Thank you.

• LR and PS will not update 'Download error' 49 customer service contact? anyone had this problem and how to solve? was running windows 8.1 and now running windows 10 but had the same problem with two BONES

  LR and PS will not update 'Download error' 49 customer service contact? anyone had this problem and how to solve? was running windows 8.1 and now running windows 10 but had the same problem with two BONES

  Check your hosts file.  to help with this and more:

  Log, activation, or connection errors. CS5.5 and later, Acrobat DC

• Two queries LOV in a point... is that possible?

  Hello
  
  I created a list of value form DML as below-
  
  Select pcrs.cost_record_status, pcrs.port_cost_record_status_id
  of ptcs_cost_record_status RFT
  
  But, depends on "pcrs.port_cost_record_status_id" I want only certain values to display in the list.
  
  For example:
  -If pcrs.port_cost_record_status_id 2
  - then view the State 2,3,4
  
  Select pcrs.cost_record_status, pcrs.port_cost_record_status_id
  of ptcs_cost_record_status RFT
  where pcrs.port_cost_record_status_id in (2,3,4)
  
  -If the State id is 1
  -can view the status of 1.5
  
  Select pcrs.cost_record_status, pcrs.port_cost_record_status_id
  of ptcs_cost_record_status RFT
  where pcrs.port_cost_record_status_id in (1.5)
  
  Any ideas on how I can have two different LOV in one?
  
  Thank you!!
  Ling

  LC says:
  Hello

  port_cost_record_status_id is a COMPONENT and it is retrieved from the database when the form is opened.

  It doesn't look like one (the convention is that page elements are prefixed with their page number and referred to as bind variables using the ":").

  Regarding the original question, which precedes the LOV query is:

  select pcrs.cost_record_status, pcrs.port_cost_record_status_id
  from ptcs_cost_record_status pcrs
  where pcrs.port_cost_record_status_id in (2,3,4)
  and :p1_port_cost_record_status_id = 2
  union all
  select pcrs.cost_record_status, pcrs.port_cost_record_status_id
  from ptcs_cost_record_status pcrs
  where pcrs.port_cost_record_status_id in (1,5)
  and :p1_port_cost_record_status_id = 1
  

• Problems with two of my OPOS hardware after upgrade from XP to 7

  I have two HP rp5000 point of sale systems and I'm having a difficult time linking two of my OPOS hardware components.  My receipt printer, A794, even after installing the new drivers still is not recognized by the computer.  The other thing that doesn't connect also the HP Pole display, I think that it's an LD220.  I recently updated the OS from XP to 7 and that's when I had the problem with my computer, try to recognize them.  The pole display is USB and the USB printer to series.  Is there any firmware for the latter to try to make them work again?  I have download the firmware for the Pole display, but that didn't work either.  I don't think I saw one for the printer.   Any help would be useful.  Thank you.

  Npgwi2000, welcome to the forum.

  I'm sorry you have to do another post, but this is the Forum for the POS systems.  Experts it will be able to help with your problems.

• Problem of two - VGA and Displayport monitors

  Hello

  We have recently purchased a number of machines Thinkcentre M58 and have problems to make two monitors to work with these machines. We are setting them up with a monitor to the VGA port and a 2nd monitor connected to via a Displayport adapter Displayport to VGA dongle.

  The problem is that the 2nd monitor on Displayport don't wake up. MESSAGE appears on the monitor 1, and when Windows has loaded, only the 1st monitor displays a screen, while the 2nd monitor remains in mode 'sleep'.

  In display settings, it is possible to activate the 2nd monitor, how he wakes up and the user can continue to use both screens. If the user stops or restarts the machine it takes to manually activate the 2nd monitor whenever they connect.

  The same thing happens on Windows XP and Windows 7 computers, and I also tried to use a number of different instructors, who all have the same problem.

  Someone else had problems to get the 2nd monitor on the Displayport works correctly? Any advice would be greatly appreciated.

  Thank you very much

  Phil

  Make sure that you set the main display on the displayport device and then connect your vga port.

• Problem running two parallel while loops

  Hello world

  I'm new to Labview and is actually my first attempt. I intend to acquire data from two rockers simultaneously through two different ports. When I run my program attached with execution has highlighted, the second loop gets higher priority. How to prevent this? Also, I'm getting error codes when running arrives at the stage where Visa read data are passed to sweep of string function. Please suggest corrections to correct these problems.

  PS: I have not yet plugged on devices, that's why the properties of connection for the two Ports are the same at the moment.

  Kind regards

  Avi0111

  
  

• OfficeJet Pro 8620: Problem with two-sided printing by default settings Officejet Pro 8620.

  On my MAC, I opened the preferences system - print & Scan - Options & supplies, the pop up window only contains two tabs: Gerneral and power levels. The other tabs such as the default settings are not displayed. So I can't set default 2 Facer of printing. In such a case, I find that I can always print both ways in the face of some software where I can change the settings for print specifically in this software. But I can't change the settings of the printer in Adobe Acrobat format, because change is always through the same interface as I mention above. How I solve the problem? I am connected to my printer via wifi. Thank you.

  

  Hello

  In Adobe Acrobat, open the print dialog box, and then click on the "Printer" button... "to access the print dialog box standard operating system.

  There should not be a default on a Mac tab, the settings can be saved as default recording these as a preset in the print dialog box, then a used preset will be default.

  Shlomi

• Problem network two computers together

  Home network with two computers, both running XP Home edition.  The two computers connected (wired) to a single router.  An external network, also on the network drive.  In the past, everything works perfectly.  Computers have been able to share files.  Computer could print via printers shared on computer B.

  Current condition.  Computer A cannot access the file or print sharing on computer B.  Computer B can access A computer as always.  Computer cannot ping computer B, but B can ping A.  Both computers have no problem asccessing the network drive.  Both computers have the same workgroup name.  I tried to run the wizzard of configuration network several times, making sure that the workgroup name is set correctly, but without success.  The message I get is: "workgroup is not accessible.  You can not have the permissions to use this network resource.  Admin contact...  Network not found path.

  The problem may have started after an update of McAfee antivirus software.  I tried to disable Firewall (McAfee and windows) on computer A and even uninstalled McAfee, but still can not computer A to do B.

  Of course, any help on where to find would be appreciated.

  Home network with two computers, both running XP Home edition.  The two computers connected (wired) to a single router.  An external network, also on the network drive.  In the past, everything works perfectly.  Computers have been able to share files.  Computer could print via printers shared on computer B.

  Current condition.  Computer A cannot access the file or print sharing on computer B.  Computer B can access A computer as always.  Computer cannot ping computer B, but B can ping A.  Both computers have no problem asccessing the network drive.  Both computers have the same workgroup name.  I tried to run the wizzard of configuration network several times, making sure that the workgroup name is set correctly, but without success.  The message I get is: "workgroup is not accessible.  You can not have the permissions to use this network resource.  Admin contact...  Network not found path.

  The problem may have started after an update of McAfee antivirus software.  I tried to disable Firewall (McAfee and windows) on computer A and even uninstalled McAfee, but still can not computer A to do B.

  Of course, any help on where to find would be appreciated.

  Have you used the Tool McAfee Consumer Product Removal?  If this is not the case, do.

  Both computers have at least one account with the same name and password?

  A very old (but XP has been around for a long time) message by Malke MVP MS:

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine. With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista: set up Windows for the connection automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• strange problem with two Cruzer 32 GB flash drives on XP Pro

  I have two Cruzer 32 GB discs that will not work on a particular PC running XP Pro SP3.

  The readers work in other PC running XP Pro and PC running Windows 7.

  Now, until someone says, "it's obviously a problem with the PC" I have to say that USB Flash drives other works very well in this PC manufacturers, as does my Seagate FreeAgent Go drive (so it is not a question of power).

  Flash only readers who present a problem are the readers of Sandisk.

  When I insert the Cruzer it flashes slowly then after maybe 20 seconds start blinking quickly and continues to do so as long as she remains inserted in the USB. There is no indication on the screen it was inserted - nothing ofering to the media browser, files, etc.

  The drive appears in my computer as drive F removavble, but no file or folder is visible.

  When I go to administrative tools > computer management > disk management, disk is NOT visible, it is not visible as a removable drive.

  In Device Manager it appears as SanDisk Cruzer USB one, using a device driver Microsoft date 01/07/2001.

  I tried to uninstall this device, removing the Cruzer then turn the PC, but when I plug it in there new detects new hardware - Sandisk Cruzer and drive hard, but then says that it can not work properly and invites me to restart the PC. Subsequently, he then returned to the symptoms described above.

  The TWO Sandisk Cruzer 32 GB disks with the same problem.

  Someone at - it any other ideas?

  Thanks pechter!

  Kies was the problem.

  I followed the instructions in this thread http://forums.sandisk.com/t5/All-SanDisk-USB-Flash-Drives/sandisk-cruzer-blade-problem-troubleshooti... and it cures the problem.

  I must point out that it has not affected any other brand of flash drive I've tried, the incompatibility seems to be only between Sandisk Cruzer and Kies, leads me to conclude that this is a problem of Sandisk.

• __When I am listening to music on the web page and scroll to the bottom of a page, the sound becomes stuttery and slows down rough down__and. This problem started two months ago. Thank you

  In addition, I noticed I have a problem with Flight Simulator Microsoft X too. I've never had a problem before. The sound is noisy, distorted and crackling. I do not add or remove anything in the last two months. It's really interesting that I have 7 games more like: IL2, star Wars and etc on my computer but there are no problem at all.

  Hello

  How can I stop my music skip or break down when I play?
  http://windowshelp.Microsoft.com/Windows/en-us/help/36db5c82-9247-4346-909a-f87743b653ae1033.mspx#EFC

  1. right click the icon of speaker near right lower clock - peripheral of reading

  Highlight speakers - properties (right same low page) - tab improvements - check Disable all sound effects
  Apply - OK

  2. check the configuration - Device Manager - sound, video and game controller

  Note name and complete model of the audio device - full decription - now double click it.
  Driver tab - notice the driver version. Then click on set to update driver (maybe nothing like MS is far
  behind the pilots of certification). Then right CLICK on the device - UNINSTALL - REBOOT - it will refresh
  the driver stack.

  Now go to system Maker and look for the updated drivers (or get the same if no new) it will be
  your rescue. Download - SAVE - go to where you put it-RIGHT click in it - RUN AS ADMIN

  Then do the same for the manufacturer of the device (like Realtek or who made the device).

  NOTE: Often restore audio drivers to check the version after installing and restarting is
  see if the version you have installed is there, otherwise repeat the installation - restart until it is. This may take
  several tests according to the recommitments how much he makes.
  
  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• problems with two stray files - automatic and custom

  Hello

  I've been tinkering with and deleting files that I should go far, and one of the effects is that I have now two folders (containing the MS files with encrypted file names) are no longer in their home for good. I put the someplace temporary where I can always find them again, but I need to know where they both came in the first place not least because they may (or may not) involve different problems that I had with my programs since I've messed around with the files, that I should not have. Two records are called 'AutomaticDestinations' and ' CustomDestinations. Can someone enlighten me please know where should I send these two files? Thanks, davidc

  Hello DAVID CORKINDALE,.

  Have you tried to do a system restore to a time before making changes?  Please let us know status.

  System Restore:

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

• Some subtle problems with two monitors on Windows 7

  I used two monitors with your Windows 7 Desktop for quite awhile and I just had to replace a.  This is a problem which is probably easy to fix, but I don't know how to do it.

  I figured out which monitor, I wanted to just in front of the keyboard (the larger one) and that I wanted on my right.  The new is more.  They both work very well, but there are two problems:

  1. the office and the taskbar are in the older monitor to the right - I do not know how to move.

  2. the mouse is confused.  He considers that the monitors are in the reverse position.  In other words, when the mouse is moved on the screen to the right, I have to move it OFF THE RIGHT EDGE OF the SCREEN to enter the screen on the left.  I know that I can get used to this, but I'd rather not have to.

  Thanks in advance.

  DK

  Right-click on an empty space on the desktop and choose "Screen Resolution."

  (or Panel of-> screen-> the resolution).

  Above under 'Change the appearance of your screens', you should see two icons of the screen display.  Simply slide one on the right to the left of the icon on the left (so that they switch positions). Then press "OK" your way out.

  To select the screen that contains the task bar, select the icon for this monitor in the same screen as above and a small box should appear below the "Multiple displays" line that says 'Make this my primary monitor '.  Just check this box and OK your way out.

  HTH,

  JW

• Problem with two Logitech F710 on Windows 7 x 64

  Hello world! I have a strange problem.

  Let me start from the beginning - I have 2 Logitech; s f710 and I was playing on them perfectly, when I had 32-bit Windows. I played with my friend in superhero marvel lego arkham city and etc. Then I changed my OS to Windows 7 64 bit and that's when my problem started.

  First I used this guide to install my F710 - it check out - http://blog.plee.me/...input-driver/

  After all the manipulation my controller was working perfectly, but then I tried to play with my friend in Mortal Kombat, one on one, or scale of tag and I discovered that this game is grateful to my two controllers AS a. Two of us could play a hero. When I tried to make one - I pressed a button on a carpet, and when I'm picking a second player - the game telling me this controller "dispositif device already in use, please select another device"!

  The same problem in Lego marvel heroes - we can not play together more.

  How can I solve this problem? You will appreciate all help!

  PS has also tried installing the emulator, but it has not fixed my problem, maybe I did something wrong?

  Hello

  Have you tried to download and install the pad Logitech Gaming Software and wireless F710 Connect Utility from the Web from Logitech website game?

  If this isn't the case, I recommend that you download and install these software and check if the problem persists.

  Wireless Game pad F710 Web site.

  I also recommend that post you the question on the Forums of Logitech you can receive assistance from their purpose as well.

  Hope that the information provided is useful. Let us know in case you need more help.

• printer and the computer communicate do not (the two Dell), the problem started two days ago. Has gone through the troubleshooting list.

  Two days ago, we started the unable to print from our computer (both are from Dell and we have not had this problem before).  The message says that they are

  does not.  I went through the troubleshooting list, nothing worked.  I don't think that this has nothing to do with the problem, but three days ago, we

  had our cleaned CPU due to a problem of piracy.

  May depend on what exactly you mean by 'cleaned because of piracy'

  Maybe you could try to reinstall the printer using the cd of the Dell printer