Problem with a hard disk on the Satellite 1800 750
Hi all!
I have problems with my Satellite 1800 750 therefore than the hard drive not to be recognized. Means I can start from floppy disk or CD-ROM, but not hard drive. I create in the hard drive to another laptop and it works well. In the BIOS, I see two (HD and CDROM) IDE devices. From pure DOS diskette and try running fdisk also does not show me the HD.
What can be? It is a total mistake on card mother IDE #1 have a defect or is it a BIOS problem? Or something else?
Thanks in advance for any ideas.
Kind regards
Werner
Hi Werner,.
He cannn be your IDE controller has a loose contact.
But in a first time, you must set the BIOS to the factory settings. Press ESC key after power! Then you have a short list of commands at the bottom of the screen!
If this does not solve the problem you correctly a hardware fault. This should be checked by a Toshiba Service partner. Go to https://eu.computers.toshiba-europe.com - support & downloads - find an authorized Service partner
Rudi Bye
Tags: Toshiba
Similar Questions
-
Hi all
Need your help. I have problems with my external hard drive. I worked on it yesterday when the cable is a little detached and disassembled my intestinal HARD drive.
Here are the specs:
1 Macbook Air 11.5 "running on El Capitan (10.11.1)
2 Buffalo Ministation external (1 TB) HARD disk divided into two: a Mac partition (for time machine) and the other a windows on FAT32 partition.
Before the accident yesterday, it was working OK.
Now, when I connect the HARD drive, it turns on but the Mac partition cannot be mounted (it does not appear on the Finder. I opened disk utility... just load forever and does not work) and the Windows partition is visible... but I can't take it apart without turning my computer.
I can assemble and disassemble a USB stick very well.
Any help would be appreciated.
Thank you!
Maybe you can explain a little better.
I would like to make some general comments before having your replay.
It is not wise to use TM on a disk with apple unformatted or partitions, it is preferable to have a dedicated TM drive also.
For TM, the rule is that the drive is about 3 times the size of the boot disk.
Normally you 'survive' a good step disassemble the drive external, but in this case with a another partition formatted on this subject, I'm not sure if that do not corrupt the disk, especially since the Windows partition is bootable. I have suspct the partition GUID on the TM partition table is corrupt.
I propose to start the disk completely: in DiskUtility select the 'higher' level (name of manufacturer) and the Partition, one OS X Extended (journaled) partition table Partition GUID. And use it only for TM, is not too big for this.
Have another drive formatted NTFS for Windows.
-
Problem with WiFi adapter (RTL8187b) on the Satellite L350-146
Hello.
Problem with WiFi (RTL8187b) on the Toshiba Satellite L350-146 adapter:
Exchange of packets of 192.168.0.177 with 32 bytes of data:
Reply from 192.168.0.177: bytes = 32 time = 3ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 4 ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 6ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 2ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 874ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 364ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 2ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 2ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 3ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 2ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 1ms TTL = 128
Reply from 192.168.0.177: bytes = 32 time = 2ms TTL = 128Ping statistics for 192.168.0.177:
Packets: sent = 50, received = 50, lost = 0 (0% loss)
Estimated duration of admission, transfer to ms:
1msek = Minimum, Maximum = 874 ms, average = 34 msWin Vista HP, drivers last.
This problem with different access points.Sorry for bad English may
Need to check if theres no interferense in your plase, check also if the WiFi adapter is ok!... you can do this reinstalling the driver and check if it works if not you have to go with an ASP in your area to check the Wi Fi card...
-
Problems with webcam and microphone on the Satellite with Windows 7
Hello
I installed Windows 7 on my Toshiba Satellite and all of a sudden the webcam and the microphone does not work.
I tried to find the appropriate drivers, but I can't seem to find.Could someone please help?
Best regards
TeresaHello
The webcam software is designed by Chicony.
This model of laptop s independent and, therefore, the use of the webcam software that has been released for other models of laptops may not be a problem.I recommend you the driver for Toshiba Satellite L500 series area.
There you can download the drivers for Win 7 32 bit and 64 bit OS.Welcome them
-
Display light goes off on the Satellite 1800 750
Hello together,
I have long been the problem, that the lighting of the screen out constantly.
By pressing the pencil with him he can press the display is turned off if a laptop broke a stop with that short that activate the new lighting display.
But now nothing more goes, too!
However, we can see on the screen what is indicated that only lighting is absent!
What can we do there?
I belonged the reverser often breaks and that you exchange it only necessary what do you say about that?
Help me please!
Thanks a lot a lot!
Affectionately yours!
JMK!
Hey JMK
Before that you're wasting your time here why you n t contact the Service of your country partner and explain the situation. I'm sure they can give you more information on the parts and prices.
Also check eBay. From time to time you can find parts or defective. These units are not expencive and with two defective, you can make one that works.
-
Waste of space on the hard disk on the Satellite C650 - 15 X
Hello
I found a problem on my laptop Toshiba Satellite C650-15 X (almost new), I bought several months ago. It has a drive hard 500 GB volume in 2 partitions: C and D-with 250 GB each; and Windows 7 Premium 64-bit operating system.
There is something strange about the partition D: it is 225 GB of missing! After scoring all of the files in the partition D > properties, there are only 25 GB in use and really little or no free space! There isn't any system or other files with this 25 GB. More than 220 GB in partition D is simply disappeared.
C partition looks normal. Tried all known Windows tools: check disk, defragmentation, convenience stores, etc. without results. Any suggestion or idea what s happened past and how to fix it? Thanks in advance!
Can you please open Computer Management > disk management. Make a screenshot and post it here.
I would like to see exact HDD structure. -
Question on the second hard disk on the Satellite A100-646?
Hi all
is it possible to install a second hard drive on laptop (I have a satellite A100-646)?
There is a solution like optbay for computer toshiba laptop?Thank you very much
Best regards
FabrizioI agree with the above use the A100 cannot be upgraded with a second HDD
I also recommend buying external USB2 HARD drive
-
What are the 150 SATA or SATA-300 supports the HARD disk in the Satellite A200-196
Can someone tell me if I need a SATA-150 or SATA-300 drive to upgrade my A200-196.
I think that the current drive of 80 Go SATA-300 but my diagnostic tool (third party) indicates the maximum speed is 150.
Thank you
RichardGreat info by the way. I found the info also, that the controller supports only SATA-150.
-
Replacing hard drive on the Satellite A60-S159
grateful for the help on the situation of the Hard disk on the Satellite A60-159 and advice on removal and replacement of the HARD disk.
Hello
Well, I put t found any blankets or slots at the bottom of the unit. In this case, I think that he must remove the keyboard and some other covers.
But if the warranty is valid you must contact the ASP for replacement because if you open the Notepad or if you remove the covers you lose the warranty.Good bye
-
Re: Satellite Pro A40 - can I change the HARD disk or the same model?
Hi Forum,
do I have to wait for safe trouble by changing the hard disk between the following laptops:
old or damaged laptop:
SPA40 model PSA45E - 0013T - number GR
Series No. 34127882 Hnew/own laptop
SPA40 PSA45E-001VM-GR model number
Series N0.34117607HThanks in advance for your advice
Concerning
You can do it. No problem at all. Hard drives are not specific model of laptop parts and with hard drives is important compatibility.
On the new laptop, which you can use different hard drives. Important is that use you compatible HARD drive.Just do it. After Exchange of HARD drive install Os again and everything will be OK.
-
I got lightroom 5.5 on a computer with a hard disk failure. How do I install it on my new computer without access to the old computer?
You can download Lightroom 5.7.1 (the final version of Lightroom 5) from the following Web site: keeping up-to-date for Lightroom
Lightroom 5.7.1 is a solid version, and you are entitled to it. You will need your serial number to activate the installation.
-
I need to reinstall photoshop elements 8 after having problems with my hard drive. I use MacBook Pro and a timemachine. After restoring the program of the Time Machine, I got the error 6 code: a license for this product has stopt working. How can I cancel it?
See here:
-
Qosmio G30 (PQG31) - problem with cloned hard drives
Hi all!
* Qosmio G30-154 * (* PQG31 *).
Demo of the Qosmio has 2 hard drives with XP MCE (32 bit) installed on the primary.
The RAID parameters are JBOD.
BIOS is "newer" 3.90I would try to upgrade the drives (without installing any OS) and... have a problem!
BSOD "Stop 0x0000007B" after 'clone with resizing' for the main HARD disk.I read on [drivers Toshiba RAID | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=48489] also [how to integrate the AHCI driver when installing Windows XP | http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm] and (or)
[SATA and AHCI Intel Matrix Storage Management Software: "the installation program found no hard disk units installed in your computer" Error Message during Manual Installations | http://aps2.toshiba-tro.de/kb0/TSB7B020R0000R01.htm], but I don't want to install OS, I want to keep intact my OS work.
F6 (for all usb drivers) is not available to boot OS, sorry."cloned" drive is in line with the correct name of made in the BIOS. "Cloned" secondary drive works (with old primary school). How to get access to the new primary OS and loading cloned? Please, any ideas?
Thank you.
Hello
I think that the system cannot boot to the new HARD disk as the partition where the system is installed, was not marked as bootable system partition.
I recommend to insert the previous HARD drive and to start the laptop.
HARD drive new, cloned could be connected as an external HARD drive to a USB port.Then you should go to disk management (right click my computer - manage-> management-> disk management computer)
Here you can see the HARD internal disk and the 2nd HARD drive connected to the USB port
Right-click on the partition (2nd HARD drive) where the Win XP has been installed and choose the partition as the system partition and mark it as active.Then you could change the HARD drive again and could power the device in place. Usually, the system should boot to the top of the new marked system partition.
-
Problem with drive HARD and Vista install
Hi all
A few weeks ago, my Dell Inspiron laptop computer started to freeze. I could boot ok and my desktop wallpaper and icons were all there, but I couldn't run or open anything. I did the Bios tests and my Vista installation disc and told me there was a problem with my hard drive. I wiped it and tried to reinstall vista and that I could see it wasn't working because it took hours and then seems to have stopped again during installation. So I bought a new one and tried to install Vista. everything was going well until it is restarts a second time and I got a black screen with a mouse pointer icon. I had to reinstall it running for about 4 hours, at least an hour of that time which was all that was going on and the hard disk wasn't spinning.
How long on avg would take to install Vista, if it is running normally?
is there anything else that might be a problem that would not appear in the repair of Vista or Bios diagnostics?
Any advice would help a lot.
If the new hard drive does not work, then the problem is on the motherboard. Your description of symptoms indicates a power supply or motherboard failure. Contact Dell technical support for repair or replacement. MS - MVP - Elephant Boy computers - don't panic!
-
problem with my laptop asking for the administrator password or power on password
I have the same problem with my laptop asking for the administrator password or power on password. It is a compaq presario cq61. It happened when my hard drive failed and was not used for a long time. With the password, any help would be much appreciated. It says system turn off after a few trials with the key: 55427586
Hello
Try to enter: 40585508
Kind regards
DP - K
Maybe you are looking for
-
TV 40WL768 Blink without active stabilization
Hello I bought 40WL768 TV for use with a computer with HDMI.I use the mode "PC."With this use, I can not activate "film stabilization", because the cursor becomes too slow (latency). The problem is that I need to enable "film stabilization" otherwise
-
Graphic on HP Pavilion is too dull and fuzzy.
Original title: HP Pavilion dv6 The graphics on my HP Pavilion dv6 are very dull & quite blurred. Can someone help me refine the image & brighten the color?
-
When I returned from vacation, my PC worked as usual, but later in the day that it would be not laod, it gets to a certain point and then a blue screen and try a reboot. Managed to use the 'safe mode' and finally 'System restore', but it kept crashin
-
original title: anti-spyware in Microsoft windows xp My computer has been infected with a virus by asking me to download windows xp for $59 virus software. Whenever I tried to load the antivirus software, or similar, I saw in the 'my windows task man
-
cat4500e-universalk9. Spa.03.04.01.SG.151 - 2.SG1.bin installed on cisco 4500th with SUP7-E, the license level is enterservice, but impossible to find, use "generations key cryptographic rsa ' to activate ssh in CLI. Who can solve it? think!