Problem with output

Similar Questions

• Problem with output 5VDC NI 9411 channel

  Hello

  I'm having a problem with output 5VDC NI 9411 channel. According to the specification of the module, it was stated that the module required external power from 5 to 30 VDC. Game of supply the module with the requirement of tension, I am still unable to get the output voltage of the output channels. Does this mean that the output voltage may be available depending on the program?

  Thanks in advance,

  Kind regards

  Mike640

  Hi Mike,.

  Thanks for posting on the forum of National Instruments.

  You should still be able to get an output voltage in properly feeding the NI 9411 and your external device.

  If you don't have a power supply of 5V to power the external device directly, or if you want to simplify the cabling, you can connect an external power supply to the Vsup and COM terminals on the connector terminal block screw NI 9411 and connect the external device to one of the pins Vout + 5. If the external device is already powered, you have not need connect a power supply on the NI 9411 or plug the Vout of + 5 to the external device.

  I hope this helps.

• Problem with output report layout

  Hi friends,
  
  This isn't problem Oracle D2K. ;)
  
  I did a report in Oracle PL/SQL. And, when I spool the data he fragments he came out in several lines. Despite I took in charge of the issues.
  
  Now, let me explain->
  
  I used a function in pipeline and store the result using the command of the coil.
  
  What I found strange, this is the type of object that is a clob data type is split in fact lines after 80 characters as in the case of string, it continues to 4000 characters.
  
  Now, in my solution, ordering channels made big role as all the lines indicate a different meaning and so pinched the data accordingly.
  
  I did a small test in that regard, and I am paste here that - because I am not allowed to post here my original due to the policy of the company code.
  

  scott>select * from v$version;
  -----------------------------------------------------------------------------------------
  Oracle Database 10g Enterprise Edition Release 10.2.0.3.0 - Prod
  PL/SQL Release 10.2.0.3.0 - Production
  CORE    10.2.0.3.0      Production
  TNS for 32-bit Windows: Version 10.2.0.3.0 - Production
  NLSRTL Version 10.2.0.3.0 - Production
  
  Elapsed: 00:00:00.18
  scott>
  
  scott>create table clob_dummy
    2     (
    3       cola clob
    4     );
  
  Table created.
  
  Elapsed: 00:00:04.40
  scott>
  
  scott>insert into clob_dummy values('&clb');
  
  Enter value for clb: Enter value for clb: gfhjtuioep mnhjkie rt-hlospd. ngktio pokdnebtt, gkhohphpdj
  dbs wmqksxnd - kfnfdkdldkdkdkdkdkdkdkdkdbdsjgdvj h geg.jv ehh  shgghsga wshkwlsgsdklghlahgkh lahgkas
   lhks  kglaks gksh a
  old   1: insert into clob_dummy values('&clb')
  new   1: insert into clob_dummy values('Enter value for clb: gfhjtuioep mnhjkie rt-hlospd. ngktio po
  
  1 row created.
  
  Elapsed: 00:00:00.08
  scott>
  scott>commit;
  
  Commit complete.
  
  Elapsed: 00:00:00.01
  scott>
  scott>select * from clob_dummy
    2  ;
  
  COLA
  --------------------------------------------------------------------------------
  Enter value for clb: gfhjtuioep mnhjkie rt-hlospd. ngktio pokdnebtt, gkhohphpdjd
  
  Elapsed: 00:00:00.27
  scott>set long 400000
  scott>
  
  scott>set lin 2000    ---- As you can see i've set the linesize to 2000
  
  
  scott>
  scott>set serveroutput on
  scott>
  scott>
  scott>select * from clob_dummy;
  
  COLA
  --------------------------------------------------------------------------------
  Enter value for clb: gfhjtuioep mnhjkie rt-hlospd. ngktio pokdnebtt, gkhohphpdjd
  bs wmqksxnd - kfnfdkdldkdkdkdkdkdkdkdkdbdsjgdvj h geg.jv ehh  shgghsga wshkwlsgs
  dklghlahgkh lahgkas lhks  kglaks gksh a
  
  
  Elapsed: 00:00:00.11
  scott>
  scott>
  scott>select length(cola) res from clob_dummy;
  
         RES
  ----------
         199
  
  Elapsed: 00:00:00.08
  scott>insert into clob_dummy values('&clb')
    2  ;
  Enter value for clb: ssjfsjgskjhghsgskgkksl hgeldhldlkskhdlk dklhkdlkhlkdlhdkfhldkhkhdkhkdhkdhkdkhkl
  hkddkhdkhdkl djhlkdkhdhkshlkd dkhdkhldsjhkslhjd eutywe 398863694 i230e ehgd ehglegighsihdlk eltiweyt
  ilhdhgehgisehbkd 
  old   1: insert into clob_dummy values('&clb')
  new   1: insert into clob_dummy values('ssjfsjgskjhghsgskgkksl hgeldhldlkskhdlk dklhkdlkhlkdlhdkfhld
  
  1 row created.
  
  Elapsed: 00:00:00.03
  scott>
  scott>commit;
  
  Commit complete.
  
  Elapsed: 00:00:00.08
  scott>
  scott>select * from clob_dummy;
  
  COLA
  --------------------------------------------------------------------------------
  Enter value for clb: gfhjtuioep mnhjkie rt-hlospd. ngktio pokdnebtt, gkhohphpdjd
  bs wmqksxnd - kfnfdkdldkdkdkdkdkdkdkdkdbdsjgdvj h geg.jv ehh  shgghsga wshkwlsgs
  dklghlahgkh lahgkas lhks  kglaks gksh a
  
  ssjfsjgskjhghsgskgkksl hgeldhldlkskhdlk dklhkdlkhlkdlhdkfhldkhkhdkhkdhkdhkdkhklh
  kddkhdkhdkl djhlkdkhdhkshlkd dkhdkhldsjhkslhjd eutywe 398863694 i230e ehgd ehgle
  gighsihdlk eltiweytilhdhgehgisehbkd
  
  
  Elapsed: 00:00:00.11
  scott>
  scott>
  
  ----- Still it is breaking the line after 80 characters. 

  Why is this it is break line after 80 characters? Alternatively, where I'm missing?
  
  But when I changed the varchar2 data type, it is good way.
  
  May I know what is the reason? Then I fixed using the clob data type? Or will I have to change to varchar2? Because, I need only single record line (any size is - this - but of course oracle time) when I wrap the output to a file.
  
  Please share your thoughts with me.
  
  Thank you.

  It may be related to longchunksize SQL layout * more. Have you tried a similar to your set linesize value assignment:

  set longc 2000
  

  It can also be bound to the version of SQL * more you use. I notice some differences between sqlplus (command line version) and sqlplusw (the windows gui version)

• Problems with output TV satellite a50 492

  Hello
  I have a new a50-492 and everything works fine, everything except Tv-out :(
  i've got BIOS type PAL, my cable TV and tv-ports are not violated, I'm sure that it works fine on my desktop pc.
  I thought I was a BIOS problem and I upgraded from 1.20 to 1.30 but nothing :( I have no screen at all on tv :( I only see a small flash on the television screen when the laptop starts. Normally, it should show the typical home Toshiba screen on the bios, but nothing happens :(
  Could someone help me?
  Do not hesitate to write even on email - [email protected]
  Thanks a lot!

  Hello

  Your model has a S-VHS connector, better and easier to get color tv (but no sound) is to use a dongle inbetween the SCART and S-VHS cable, the dongle must be a computer--> SVHS--> SVHS<->RGB--> SCART-> TV,.

  As I mentioned you won't have any sound, but this can be picked up from the computer with a separate cable. Not worthy, I also have experience of PAL systems on the point above.

  BR

• Satellite L850-147 - Audio problem with output jack and balance

  Hi all

  When I plug in my headset on my laptop (Satellite L850-147) and try to listen to music, I hear music (instrumental parts)... by far, I can hear the voice of the singer.

  I found a turnaround with the adjustment of balance in realtek HD audio manager 100% or 100% left...
  But this isn't the way that music have to play...

  I have reinstalled the Realtek HD Audio Manager but without success...
  Any idea?

  Thank you

  Hello

  And have you checked the settings in the software you use to play the sounds?
  Of course the Realtek HD audio Manager supports the sound configurations and you can change different sound effects such as environment and Equalizer but the same or similar options are supported by each software reading and I also recommend to check this!

  By the way: Toshiba laptops are pre-installed with a HD Audio SRS Premium application. To access this, go to:
  Start-> all programs-> SRS Lams-> SRS Premium Sound Technology
  Here, you will also get some options that could be interesting for you.

  Also recommend checking Audio improve
  Make a right click on the icon of speakers in the taskbar then on playback-> speakers devices->, click Properties
  On the development tab, select the sound effect you want and click on apply.

• Strange sound problem with Satellite L740 TV outputs

  I'm having a strange problem here... I googled this several times already, and I only found the same solution mentioned several times and the given solution * not * work is to me.

  I have a Toshiba Satellite L740 running Windows 7 Home Edition Premium, with a 64-bit Intel Core i5 - 2410M @ 2.30 GHz CPU and 4 GB of physical RAM. My problem is the following...

  There are two different TVs in my house that I regularly connect my laptop via HDMI cable.
  The first is mine, and I can get sound through the TV very well when I plug it in.

  Sometimes, however, I will disconnect the computer from my TV and not get any sound through the laptop because he's trying to output to external speakers to TV.

  More importantly, when I connect my laptop to my * roommate * TV (the same make as mine, you mind), I can not all the sounds of his TV at all.

  This is a recent problem. Until this morning, I was able to get noise from two TV very well and only sometimes had problems with sound through the laptop itself, which has been easily resolved by restarting.

  It's just a hunch, but it's almost like * doesn't realize that there are two different TVs * that it is connected to my computer. Maybe it's stupid, I don't know, but be it, it's frustrating...

  * ALSO: * I've seen dozens of suggestions that I put my HDMI audio as default device. Yes, I did. It wasn't the issue. Is the same to activate my audio drivers in Device Manager. They are all turned on, so it's not that either. Any ideas?

  It's a bit strange if you connect the laptop to two identical televisions and use the same HDMI cable to the TV.

  Unfortunately, it all works automatically and I put t know if you can force your laptop to recognize two TVs on the same path.

  In the worst case you have to do it manually in the sound properties > playback devices.
  If it works with four mouse clicks you can change.

  I tested my laptop with two different TVs.
  At home, I have a Toshiba TV and at the office we use Sony. On both automatically get sound on the TV speakers.

  If you will be able to find the solution please let us know.

• Problems with the digital input/output

  Hello

  I have a little problem with my card PCI-6143. I would use two connectors digital one as a starter and one as an output. Now, I have the problem that I do not know how I address them. The input works as I want but not the output.

  As an example. I call my channel output on this name: Dev1/port0 / line0:0.
  With this call, the application works very well. If I change the output channel to Dev1/port0 / line4:0 I get an error that the values can be read and 0 and 1 are valid values.
  I hope that the call is right, I wrote that out of my head.

  My questions are. Is it correct to call a single digital channel with this name?
  I'm not sure because I do not understand what these means 'line' and if I allocate really single channel or more.
  The second question is, can someone give me an example of how I assign two digital channels (how to address them)?
  I know it's maybe an easy question, but I can't seem to get it corrected.

  Hope someone can help me.

  Best regards

  The syntax that you use is intended to select several channels: the numbers are the initial and final channel in a subsequent channel list. Thus, written Dev1\port0\line0:4 means 5 lines are included in the read/write (FWIW written 4:0 has the same effect). It is redundant but good writing line0:0, which means a single line, but you can write to Dev1\port0\line0 which is simpler.

  This is a help page on this topic.

• Strange problem with analog simultaneous output / input

  I use a card PCI-6221. I have an application which generates 2 waveforms (finished samples) and simultaneously records 4 channels of analog input. I am using the sample clock AO as the sample for the analog clock.

  As a test, I plugged in the first AO (AO0) all 4 channel inputs. What happens when I run the vi, it's that the first sample on the first string (AI0) has the value of the last sample that was out on AO0, of the previous generation.

  Example:

  AI0 AI1 AI2 AI3

  -0.369-0,001-0,001-0,001

  -0.001 0.062 0.062 0.062

  0.062 0,124 0,124 0,124

  etc.

  I understand that it is a problem with the relative time of update of the AO and sampling of IT.

  He has to go: AI0 read / write AO0 / read AI1 / read AI2 / read AI3.

  I use DAQmx Timing (sample clock) to specify the clock AO as the sample for the AI clock. I noticed that this has an advantage of input terminal called assets. Ah, I thought - if I put the active side to neutralize the AI always begins sampling half a clock cycle after the OD has updated. Evil. It makes absolutely no difference. Maybe the AO clock signal is a very short pulse?

  Is there a way to specify the order in which updated inputs and outputs analog / sample?

  Hi CDancer,

  Change analog output voltage is not instantaneous. It depends on the speed of scanning of the Council with the difference the tension of the previous.

  You're right that the AO sample clock is a very short pulse. As far as I remember, it is the order of 50 ns.

  Here are two ways to insert a break between the tasks of HAVE and AO:

  • Delay the first conversion of IA (AI0) regarding the sample clock HAVE: use DAQmx calendar > more > converted > sample clock delay > Delay and DelayUnits properties.
  • Delay the sample clock HAVE first with regard to the relaxation of beginning of AI: use the DAQmx > start > more > Delay and DelayUnits properties.

  Brad

• Problems with HSRP output

  Hello dear!

  I have the following topology:

  Cisco 3845 gi0/0 - switch Foundry - fa0/0 Cisco 7206VXR

  CISCO 3845 *.

  interface GigabitEthernet0/0
  IP 192.168.80.90 255.255.255.128
  no ip proxy-arp
  IP accounting output-packets
  full duplex
  Speed 100
  media type rj45
  standby 2 ip 192.168.80.89
  standby priority 2 130
  LAN service-policy input

  CISCO 7206 *.

  interface FastEthernet0/0
  IP 192.168.80.91 255.255.255.128
  no ip proxy-arp
  Summary-address eigrp 100 IP 172.31.255.0 255.255.255.0 5
  full duplex
  Speed 100
  No cdp enable
  standby 2 ip 192.168.80.89
  standby priority 2 150
  2 standby preempt delay minimum 60
  standby 2 track Serial6/0 80
  LAN service-policy input

  This devices run HSRP, but I been out following diagnosis in two routers using 'show Eve '.

  See the day before

  Cisco 3845 *.

  FastEthernet0/0 - group 2
  The State is active
  2 state changes, last state change 5w6d
  Virtual IP address is 192.168.80.89
  Active virtual MAC address is 0000.0c07.ac02
  Local virtual MAC address is 0000.0c07.ac02 (the default value of the v1)
  Hello time 3 sec, hold time 10 sec
  Next Hello sent to 1.488 seconds
  Enabled, preemption delay dry 60 min
  Active router is local
  Standby router is unknown?
  Priority 150 (150 configured)
  Follow the State of Serial6/0 interface Up decrement 80
  The name of IP redundancy is 'hsrp-Fa0/0-2' (default)

  See the day before

  Cisco 7206VXR *.

  GigabitEthernet0/0 - group 2
  The State is Init (interface to the bottom)
  Virtual IP address is 192.168.80.89
  Active virtual MAC address is unknown
  Local virtual MAC address is 0000.0c07.ac02 (the default value of the v1)
  Hello time 3 sec, hold time 10 sec
  Pre-emption turned off
  Active router is unknown?
  Standby router is unknown?
  Priority 130 (130 configured)
  The group name is "hsrp-Gi0/0-2" (default)

  I can ping to both devices using the virtual ip address.
  The work around to solve the lines ' active router is unknown and standby router is unknown "are remove the hsrp configuration in the watch system, after the issue is resolved, but came on after a few days.
  The problem is that I have not access to the Foundry switch but I think that HSRP configuration have no problem, even in the buffer, I did not see any problem with HSRP.

  Someone have similar problem or any idea?

  Thank you more

  Hello

  I would try

  (a) using HSRP worm 2 (see http://www.cisco.com/en/US/docs/ios/ipapp/configuration/guide/ipapp_hsrp_ps6922_TSD_Products_Configuration_Guide_Chapter.html#wp1102891 )

  (b) looks a little stange me have first refusal configured on a router only.

  (c) there could be some problems with your multicasts to send/receive of Foundry switch used by HSRP?

  HTH,

  Milan

• problem with the definition of a boolean as output parameter type

  Hi, I have a problem with the definition of type boolean as output parameter and it must return true if the query procedure retrieves one line else it shouuld return false

  Hi, I have a problem with the definition of type boolean as output parameter and it must return true if the query procedure retrieves one line else it shouuld return false

  And what are the issues? Its simple.

  SQL> create or replace procedure is_emp_exist
    2  (
    3     p_empno  in  emp.empno%type
    4   , p_result out boolean
    5  )
    6  as
    7     l_empno emp.empno%type;
    8  begin
    9     select empno into l_empno
   10       from emp
   11      where empno = p_empno;
   12
   13     p_result := true;
   14  exception
   15     when no_data_found then
   16        p_result := false;
   17  end;
   18  /
  
  Procedure created.
  
  SQL> declare
    2     l_result boolean;
    3  begin
    4     is_emp_exist (7788, l_result);
    5
    6     if l_result then
    7        dbms_output.put_line('Employee Exist');
    8     else
    9        dbms_output.put_line('Employee does not Exist');
   10     end if;
   11  end;
   12  /
  Employee Exist
  
  PL/SQL procedure successfully completed.
  
  SQL> declare
    2     l_result boolean;
    3  begin
    4     is_emp_exist (1000, l_result);
    5
    6     if l_result then
    7        dbms_output.put_line('Employee Exist');
    8     else
    9        dbms_output.put_line('Employee does not Exist');
   10     end if;
   11  end;
   12  /
  Employee does not Exist
  
  PL/SQL procedure successfully completed.
  
  SQL>
  

• We have a problem with a freshly installed with CC 2014 and Acrobat Pro DC - Mac whenever we click on the output preview tool, Acrobat Pro DC instantly crashes. It occurs without worrying that press ready PDF we open. Help, please!

  We have a problem with a freshly installed with CC 2014 and Acrobat Pro DC - Mac whenever we click on the output preview tool, Acrobat Pro DC instantly crashes. It occurs without worrying that press ready PDF we open. I tried to delete the folder/Library/Application Support / Adobe, but without success. the App said CC DC Pro Acrobat is installed, but the uninstall option is grayed out (I thought back to Acrobat Pro XI, but I can't do it yet). We use a local server to send updates of Adobe software, which could be the reason. Ideas accepted with gratitude as to how we can get insight into the output works again!

  Known issue for PDF files that have an output RGB mode.

  Version update of the software that will be released next month with the fix.

  -Dov

• Problems with the script to output event

  In fact I don't know if I have a problem with the Exit event or if there is something wrong with my script syntax... The output of a field event, I check if the field is empty or not and check a flag I put in place.

  The first if statement works - if I get back a value in the field, everything goes as planned. If I delete the value of the field, nothing happens.

  //if field has a value hide subSection04
  if (!(this.rawValue == null || this.rawValue.length == 0))
  {
       subSections.subSection04.presence = "hidden";
  }
  
  //if field is empty and flag equals true show subSection04
  else if ((this.rawValue == null || this.rawValue.length == 0) && (subFlags.Commercial.rawValue == true))
  {
       subSections.subSection04.presence = "visible";
  }
  
  //if field is empty and flag equals false hide subSection04
  else if ((this.rawValue == null || this.rawValue.length == 0) && (subFlags.Commercial.rawValue == false))
  {
       subSections.subSection04.presence = "hidden";
  }
  

  There are a few groups radio button that also control this behavior, they are all inter relate. So I tried also triggers the Click event of a radiobutton Group (which resembles the value in this field) out of this area, but that doesn't seem to work.

  Hi Jono,

  Your expression subFlags.Commercial.rawValue is true compares a String data type with a Boolean data type.

  Edit the expression as subFlags.Commercial.rawValue is 'true'

  I hope that this should work for you.

  Your code should look like

  //if field has a value hide subSection04
  if (!(this.rawValue == null || this.rawValue.length == 0))
  {
       subSections.subSection04.presence = "hidden";
  }
  
  //if field is empty and flag equals true show subSection04
  else if ((this.rawValue == null || this.rawValue.length == 0) && (subFlags.Commercial.rawValue == "true"))
  {
       subSections.subSection04.presence = "visible";
  }
  
  //if field is empty and flag equals false hide subSection04
  else if ((this.rawValue == null || this.rawValue.length == 0) && (subFlags.Commercial.rawValue == "false"))
  {
       subSections.subSection04.presence = "hidden";
  }
  

  Nith

• Serious cutting problem with HDMI HD output a7s

  I am a filmmaker from THE base and possess an a7s & package Odyssey 7 q + recorder camera.

  I just noticed a serious technical problem that must be addressed. When shooting video with the A7s, the component of luminance of the HD which are sent via HDMI signals are cut to 100IRE, no matter what profile picture gamma setting is chosen. I can see it in the waveform, the chrominance information is not cut exceed 100IRE. For example, when I turn the curve of gamma slog2, exposed blue sky just before clipping has kept above blue channel 100IRE, but more balanced information clip of signals (such as a piece of white paper).

  This problem does not appear in the output HDMI 4 K or record XAVC-S internal. It is true both of these formats. It is specific to flow out of the HDMI port uncompressed HD video. I'm sure that it is a firmware issue.

  This conclusion came after I noticed it during a shoot and have led to extensive testing. I would prefer a real difficulty as opposed to workaround, because it cut a stop of information from the latitude to highlight whenever I have to shoot 60 p or don't want to shoot 4 K.

  Apparently, it's a problem with the recorder of Odyssey is not correctly interpret the sony exposure output scaling. Convergent Design is working on a fix to include with their next update of the firmware. I see this problem on Shogun I tested.

• Problem with the conditional tags in printed output

  I write help files for different versions of our software - version 4 and 5 using Robohelp for HTML 5.0.2
  
  There is a large overlap of information between the two, so I use a help file joint with marked topics that are specific to version 4 or version 5.
  
  I went out and then use with 'NOT v4' or "NOT v5" as the conditional tags.
  
  It works fine in the HTML output. However, I encountered problems with the printed output.
  
  Ideally, I want the help file using the option "generate the single document" because it means that the document produced, without the single output field. However, when I do, the tags conditional build fail and I get a piecemeal result.
  
  If I generate the document by using the option 'generate individual documents' tags conditional build work, but I get the only field I want to avoid.
  
  Does anyone know how to get the conditional tags to work when the option "generate the single document" is selected?

  Pierre and HKabaker - thanks for your comments.

  I think I have the answer now.

  In the properties for the SSL Print dialog, the third screen is the dialogue of section layout. I had removed some sections in the right pane (for example, the default title page, glossary, and index) because I did not want them to appear in the final printed output. It seems that without these sections present conditional compilation tags do not work correctly when the document is released by using the option 'generate a single document ".

  I started again with a "blank" printing of SSL version. Conditional constructions using the "generate a single document" appear to work fine when I leave the dialog layout intact section.

  I can even do the conditional tags build an injustice because the option "generate a single document" (after that I made the changes in the dialog layout section) seems to be that some of the chapters in the table of contents and omitting others.

• problem with ghostscript ["Distill" did not produce the output file]

  Hello
  
  We try to convert the files to PDF using ghostscript.
  The steps that I followed by installing the Distiller
  
  First, I installed gs8.64 and configure distiller
  Refinery engine server-> Conversion Settings-> third-party Application-> Distiller Settings-> options->
  Use GhostScript and the path to install dierctory under C:/Program Files/gs/gs8.64/
  Installed according to the pdf printer
  Conversion-> primary redention web settings-> convert to PDF using third-party applications
  
  Server details:
  CS: 10gr 3
  Ghost script 8.64
  
  Please find details of newspapers below
  
  Error log...
  Copy c:/ucm/server2/vault/~convert/idc/2/2.txt to c:/ucm/server2/vault/~convert/idc/2/temp.ps
  Waiting for exclusive access on c:/ucm/server2/vault/~convert/idc/2/temp.ps
  Get exclusive access to c:/ucm/server2/vault/~convert/idc/2/temp.ps
  Waiting to distill
  Look for the c:/ucm/server2/vault/~convert/idc/2/temp.pdf file does not have
  "Distill" did not produce the output file 'c:/ucm/server2/vault/~convert/idc/2/temp.pdf '.
  Exception type is "java.lang.Throwable". Details
  An error has occurred. The stack trace below shows more information.
  
  ! $Copying c:/ucm/server2/vault/~convert/idc/2/2.txt to c:/ucm/server2/vault/~convert/idc/2/temp.ps < br > waiting for exclusive access on c:/ucm/server2/vault/~convert/idc/2/temp.ps < br > obtained exclusive on c:/ucm/server2/vault/~convert/idc/2/temp.ps < br > access pending on distilled < br > check for the c:/ucm/server2/vault/~convert/idc/2/temp.pdf file has no < br > 'distilling '. did not produce the output file 'c:/ucm/server2/vault/~convert/idc/2/temp.pdf '. < br >! syExceptionType, java.lang.Throwable
  java.lang.Throwable
  at intradoc.common.IdcLogWriter.doMessageAppend (unknown Source)
  at intradoc.common.Log.addMessage (unknown Source)
  at intradoc.common.Log.errorEx2 (unknown Source)
  at intradoc.common.Log.errorEx (unknown Source)
  at docrefinery.agent.Logger.logError(Logger.java:138)
  at docrefinery.convert.StepHandler.executeStepByName(StepHandler.java:140)
  at docrefinery.convert.ConversionDriver.processSteps(ConversionDriver.java:231)
  at docrefinery.convert.ConversionDriver.convertDocument(ConversionDriver.java:144)
  at docrefinery.convert.ConversionDriver.processSubConversion(ConversionDriver.java:165)
  at docrefinery.convert.StepHandler.executeStepByName(StepHandler.java:109)
  at docrefinery.convert.ConversionDriver.processSteps(ConversionDriver.java:231)
  at docrefinery.convert.ConversionDriver.convertDocument(ConversionDriver.java:144)
  at docrefinery.queue.PreConvertedRefineryQueueMonitor.handleCurrentQueueItem(PreConvertedRefineryQueueMonitor.java:204)
  at docrefinery.queue.PreConvertedRefineryQueueMonitor.monitorRefineryPreConverterQueue(PreConvertedRefineryQueueMonitor.java:125)
  to docrefinery.queue.PreConvertedRefineryQueueMonitor$ 1.run(PreConvertedRefineryQueueMonitor.java:93)
  at java.lang.Thread.run(Thread.java:595)
  
  Conversion completed - step PostscriptToPDF forced conversion conversion due to the error engine failure: 'Distil' did not produce the output file 'c:/ucm/server2/vault/~convert/idc/8/temp.pdf '. ». Exception type is "java.lang.Throwable".
  
  
  Please suggest me where I'm wrong...
  
  Thanks in advance,
  
  Prasad V.

  Hello

  This pf ghostscript version has some problems with conversions and I saw what happens sometimes. I recommend you go to 8.63 if available and the restest to see if the conversion fails

  Thank you
  Srinath