Problems after changing the CPU!

Similar Questions

• Printer problem - after changing the cartridge, I get a message that the USB cable is not connected

  As above. I checked the USB port and it is connected.

  Original title: printer problem. After changing the cartridge, I get a message that the USB cable is not connected?

  Hello

  1. you receive an error message/code when you try to print?

  2. What is the serial number and model of the printer?
   
  Follow the steps.
   
  Method 1
  Run the hardware and devices Troubleshooter
  This utility checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Also run convenience store Print that would help us diagnose the problem better
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 2

  (a) check the physical connection of the printer and make sure that the USB cable is properly plugged.

  (b) connect the printer to a different USB port and check if it helps.

  (c) check the on another computer.

  Method 3

  Run the fix - it tool from the link.

  Diagnose and automatically fix problems printing and printer http://support.Microsoft.com/mats/printing_problems/

  Method 4
  If the previous step fails, follow the steps described in the following link:
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
   
   
  Let us know if it helps.

• DRIVER_IRQL_NOT_LESS_OR_EQUAL after changing my CPU!

  HI, after changing my CPU to an AMD Athlon 64 x 2 5600 + (2.9 ghz), I get a BSoD when I play games or something that takes over the CPU usage.

  Minidumps read with debugging watch tool this probably caused by: ntkrnlpa.exe (nt + 467eb)

  Follow-up: MachineOwner

  Any possible solution? Or is it my damaged CPU?

  Hi Ulises,

  I suggest for the link and follow the steps to fix the blue screen errors:

  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Important:  The data available on bad sectors may be lost when chkdsk attempts to repair your hard drive.

  Just reply to us if the problem persists.

• HP a1250n, radeon xpress 200 question after replacing the CPU, Standard VGA Graphics goes not down

  Recently, I messed up my CPU and bought a replacement (exact same kind). I am running windows 7 ultimate and for about 6 months prerequisites with no problems. After replacing the CPU I get intermittent lock ups, sometimes with a small portion of the screen flashes. I say intermittent but at least every 15-20 minutes. Different programs, different habits, but still the screen freezes.

  I went in and deleted the driver under graphics cards, pick a 'completely remove the option' - it after restarting the system on its own charged for a Standard VGA Graphics Adapter and since there is then no more accidents. Of course the functionality is not as complete, large icons and such, but it works.

  If it certainly seems to point to a driver conflict I think. But for this machine, is there ever any single Vista Windows 7 driver. My skills are not so, but I'm moving.

  Any guidance?

  Hello

  Yes, your PC has integrated graphics controller: ATI Radeon XPress 200, we don't find drivers compatible Windows 7 ATI.

  The BEST OPTION: Buy a video card, then insert it into slot PCI Express 16 on the motherboard to better display and multimedia performance with Windows 7 to a value using else, it looks just like Windows XP

• HARD does not work after changing the disk partitions recovery media creator

  Hello world

  After installing windoows 8.1 April major upgrade (win 8.1 presents as OEM), and have shrunk C partition to create a data partition "D", "Troubleshooting" option under advanced start menu is no longer available.

  Toshiba Recovery Media Creator does not work, too (it can not find any hard disk recovery partion).
  I got in the OEM recovery partition.
  I am also able to create a recovery using the Windows tool unit.
  You have no idea about it?

  Thank you very much!

  Hello

  Sorry to hear about all this. Unfortunately, you now have a big problem. I don't understand why you didn't create support of recovery before you started to change the factory settings, including to change the structure of the partitions of HARD drive.

  Mobile offered with factory settings a structure specific partitions and recovery recorded image is saved on the partition of drive specific and marked with invisible markers. These markers are visible for preinstalled Toshiba recovery media creator tool and when you start the tool can find points of reference and has full access to specific files.

  Unfortunately, after changing the original scores structure Toshiba tool cannot find these markers more and is not able to copy files from recovery media recovery. What you need now is the original recovery disk. Using this disk, you can install original recovery image and after doing this, you will have new factory settings.

  I know it sounds stupid now but you must order the original recovery disk and it can be done on https://backupmedia.toshiba.eu/landing.aspx

  If you have any other questions you are welcome.

• Satellite 4080 Xcdt, small image after changing the resolution to 800 x 600

  Hello.
  After changing the resolution to 800 x 600 or less (while playing an older game BACK), the screen is reduced to the size of the postcard.
  Someone at - it an idea to solve this problem, (another driver display or s.th.)?

  Greetings, r.

  Hi Ralf,.

  In my view, there is a setting in the BIOS to force the screen image to stretch to fit the available space.

  Kind regards

• After changing the administrator password in windows server 2003, I can not connect the next day why?

  After changing the password in windows server 2003, when the new password take effect?

  Hello

  In dealing with the problem with Windows Server 2003, it would be preferable to send the same in the Technet community. http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  Hope the information is useful.

• Office Jet 6500 will not print after changing the ink cartridges

  Office Jet 6500 will not print after changing the ink cartridges

  Hello

  This doesn't seem to be a problem with the printer itself and not Windows. I also suggest to contact the manufacturer. In this case, HP.

  Please see here: http://www8.hp.com/us/en/support-drivers.html

• Can I change the CPU under my XP OEM?

  I have an OEM computer, and I would like to change the processor in the it. I know, if I change the motherboard, it fails on activation, but what if the CPU has changed?

  I have an OEM computer, and I would like to change the processor in the it. I know, if I change the motherboard, it fails on activation, but what if the CPU has changed?

  You should not have a problem if you only change the CPU. However, if you change too many things at the same time, which could cause an activation problem.

  Suggest that to create a backup Image before you start. The Image can be used to roll back the OS at a time before, when changes have been made.

  Acronis True Image 2011 - has a 30 day trial version available.
  (Install Acronis and then create a bootable media restoration/rescue CD before you begin creating an image backup)
  http://www.Acronis.com/homecomputing/products/TrueImage/
  The version comparison: http://www.acronis.com/homecomputing/products/trueimage/comparison.html
  True Image User Guides and documentation:
  http://www.Acronis.com/homecomputing/download/docs/

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• error printhead after changing the printhead in L7680

  I have an OfficeJet Pro L7680 that is a few years old.  Recently, I have noticed a decline in the print quality for mainly black, but also a little yellow, and after changing the black cartridge with no changes, I decided to change the Black/Yellow Printhead.  So, I thought that if I'm trying to change a print head, I should change the other (cyan/magenta).  I bought new Office Depot print heads.  After replacing the print heads that I was able to print a page or two, and then all of a sudden the printer started saying there is a problem with the cyan/magenta printhead.  I tried to remove and reinstall, the suppression and power reset and then put it back up, etc, but nothing moves it.  I have not yet called HP, but I hope that when I do they will help because the print heads are under warranty until 2014, even if the printer is out of warranty.  In the meantime, I thought I would ask here is - it possible I only have a print head of DOA?  Or would it be the printer?  Unfortunately I threw the old printheads immediately (stupid me) so I can't try that goes back to the old magent/cyan print head and see what happens.

  Hello jmmarton.

  Your chip printheads were damaged by inserting wrong while the transport is always on the right side. This document provides instructions on how to replace the printhead to the unit.

  Use the link below to find how to contact HP phone support in your country.

  http://WWW8.HP.com/us/en/HP-information/summary/WW-contact-us.html

  See you soon!

• HP laserjet p1006: does not print after changing the toner

  I just changed the toner. The green light is on, but when something I send to the printer to print, the orange error light. Before inserting the toner, I pulled the Strip in transparent plastic attached to an orange tongue and the black cloth. I tried to reinsert the toner and turn on/off the printer again. Help please if you can. Thank you!

  Hi @cindycb,

  Welcome to the Forums of HP Support! I read your post and to see that when you try to print after changing the toner, the Attention light. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Make sure all the orange, packaging material is to remove the toner.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Try and print a self-test on the printer hardware to see if it is a hardware or software problem.

  Open and close the cover five times quickly. It should print a page with black lines on it.

  You can find the flashing light distribution in this document and the right solutions for the reason that you are experiencing, lights blinking on HP LaserJet P1005, P1006, P1007, P1008 and P1009 Printer Series.

  You use Genuine HP Toner?

  Please let me know the result and if there is anything else I can help you. Thank you.

• What I would do is change the hard drives for some more great and maybe change the CPU. Is it possible to re - install the generator in system because I'm not changing the motherboard?

  I'm running an integrator system Windows 7 64 bit on an older system. What I would do is change the hard drives for some more great and maybe change the CPU. Is it possible to re - install the generator in system because I'm not changing the motherboard?

  Original title: Windows 7 OEM System Builder

  I'm running an integrator system Windows 7 64 bit on an older system. What I would do is change the hard drives for some more great and maybe change the CPU. Is it possible to re - install the generator in system because I'm not changing the motherboard?

  Yes, you can reinstall Windows 7 OEM System Builder License on the new hard drive with the new processor.

  It will not be a problem in this case, since you don't "move" installation, you are doing a new installation. The less it will take is activation of the phone, as you change the hard drive:

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• Internet connection is slow after changing the MAC address

  * Original title: win7... problems with internet after changing the WIRELESS card MAC address

  I have win7 home ed... .i tried to change my WIFI MAC address of the card (I had a reason to do so), SMAC program change but I could not, the address remained the same... I changed my mind... has decided to forget about this topic... but unfortunately, I had a big problem (very probably)... the internet connection is too slow or stop a few times pages load too slowly or especially do not charge. downloads are always stop in network on Chrome error... I tried a different browser to check, but the problem exists with all explorers, it's big terrible trouble please help me (Note: this problem is related to some how with internet traffic... late night speed is much better, but not 100%... but of course not as speed) ", I had before changing to MAC)... Thank you very much

  Hello

  1. what made you want to change the MAC address?

  2. what exactly happens while you are trying to connect to the internet?

  3. you receive an error code or error message? If Yes, what is the full error message?

  4 have you checked the issue in internet explore as well?

  Please follow the steps below and we update with the results.

  Method 1: Run the network troubleshooter, and check.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  Please try following the steps provided in the article and check out them.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  For more information, see the articles and check out them.

  10 tips to help improve your wireless network

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx#fBid=hq7zl63PiZ9

  Why is my Internet connection so slow?

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow

   

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps!

• After changing the port (1521 to 1525 in listener.ora and tnsnames.ora) OEM: the database is down

  Hello

  I'm installing Oracle Database 11 g 2 (11.2.0.4) on Oracle Linux 7.1.

  In short, what I'm trying to do now is changing the default port of 1521 to 1525.

  So I stopped the listener (lsnrctl stop) and then changed my listener.ora and tnsnames.ora:

  Listener.ora

  listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora

  # Generated by Oracle configuration tools.

  LISTENER =

  (DESCRIPTION_LIST =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))

  )

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1525))(HOST = localhost))

  )

  )

  ADR_BASE_LISTENER = / u01/app/oracle

  tnsnames.ora

  tnsnames.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/tnsnames.ora

  # Generated by Oracle configuration tools.

  BI =

  (DESCRIPTION =

  (ADDRESS_LIST =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1525))(HOST = localhost))

  )

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = bi)

  )

  )

  And then changed the local_listener:

  SQL > ALTER SYSTEM SET LOCAL_LISTENER = "(ADDRESS = (PROTOCOL = TCP)(HOST=localhost) (PORT = 1525))";

  SQL > ALTER the REGISTRY SYSTEM;

  Finally, I started the listener (lsnrctl start) again.

  Then I tried to connect using Oracle SQL Developer to the customer. The port of 1525 works perfectly well.

  The problem is, when I open the OEM (Oracle Enterprise Manager), it says: "the database is down. Please specify the credentials of the host to access the restart and database diagnostic tools," which is like this: http://imgur.com/oKLPW65

  So I logged on the account of the host, and it shows that the database instance, listener and the agent is all down like this: http://imgur.com/Bzr84bz

  It seems that the port used by the OEM is always 1521.

  What should I do? Can someone help me solve the problem?

  Thanks in advance.

  UPDATE:

  After changing the emoms.properties & the targets.xml (thanks to Elisabeth), you will need to reconfigure dbconsole using emca.

  So what I'm doing is decreasing the config:

  $ emca - deconfig dbcontrol db-rest drop

  and then create again:

  $ emca - create config dbcontrol db-rest

  Voila.

  Best regards

  Jerry Antonius

  Hello

  Try to change the port numbers in the following files

  Don't port no 1521 to 1525

  $ORACLE_HOME /_SID/sysman/config/emoms.properties

  oracle.sysman.eml.mntr.emdRepPort = 1525 (before 1521)

  $ORACLE_HOME /_SID/sysman/emd/targets.xml

  (Before 1521)

  (Before 1521)

• AutoConfig required after changing the Paswords

  Hello
  Everytime when I use it to change the password apps and sysadmin, I always use to run automatic configuration after you have changed the passwords on the application and database level.
  
  AutoConfig & change password
  
  But a few days back we had problem in our DR autoconfig changed the entries of the AMT and the password file and the sending of log files has been arrested.
  
  This time, I'm afraid. Should I run it every time on the applications and the database.

  Should I must run autoconfig on DB level also after changing the FNDCPASS apps on the Application tier password.

  Yes, please run AutoConfig on each node application/database layer.

  Thank you
  Hussein