Problems Linux - instance of stop - start instance.

Similar Questions

• Steps to stop / start CRS & ASM RAC 11 GR 2

  Hello gurus,
  
  
  The environment is as below:
  
  RAC 2 nodes
  Oracle RAC 11 g 2
  Enterprise Linux Server version 5.5 (Carthage)
  
  I'm new on RAC Oracle 11 g 2 and facing some problems if the message stop / start crs & asm.
  
  We want to restart both nodes and for this I did following steps.
  
  1 srvctl stop database-d < db name > - of a node
  

  Database is down now.

  2 srvctl stop nodeapps-n < host name >--on both nodes of the
  

  services are now declining.

  3. now I want to cpl
  
  $ export ORACLE_HOME=/u01/app/11.2.0/grid (grid home)
  
  $ srvctl Cpl - this does not prevent ASM instance.
  
  4 crsctl stop crs - this is also not working.
  
  
  I would be grateful if you give me please complete steps.
  
  
  Thank you and best regards,

  do as follows (as user root):

  cd $GRID_HOME/bin
  ./crsctl stop cluster -all
  

• Photosmart C6180 problem of Power-Up/Power-Down - loops on/stop/start/stop etc.

  I had the C6180 Photosmart wireless connected to a Mac OS X 10.5.6 laptop Macbook Intel and IBM PC XP SP 2 for more than 2 years.  I did have major problems with the printer.

  Recently, I have known a couple of electric in my house.  Since then the printer has turned off randomly once or twice.  Today the printer began to turn off/on/off/on/turned off/turned on etc.

  It lights up and shows the HP logo and process bar animation for one minute, followed by the message: "abnormal termination.  To avoid damage on the button to turn off the printer.  Do not use a wall or the band switch to close.  Press OK.  Then he stops and leaves upward.

  I tried to enter batch Mfg mode by organizing the * and # keys.  It flashes "Mfg commands - enter special Key Combo" for the second of two, then stops and makes a loop on/stop/start/stop again and again.

  I have disconnected all data cables, installs the printer in another room, closes the wifi on both computers and connected directly to the wall on a different circuit to eliminate problems of low power as the culprit.  I swapped the power cable between the wall and the block of the AC adapter with the same exact type of cord of another piece of equipment with the same results.

  I wonder if it is a symptom of a surfboard logic damaged in the printer, or a problem with the AC adapter?

  If it is the logic board, does pay to get it fixed?  An equivalent printer for Mac would cost about $200.  Not to mention that I came just to have stored on cartridges.

  What is a likely indication of a problem of brick AC adapter?  If so, should I spring for a replacement block AC adapter for $30?

  I was not able to find this question in a post on the forum and I was wondering if it's 'Au revoir' to the C6180?

  Thank you for your contribution to this number

  Try this:

  1. If the printer is still on, unplug all rigid and flexible cables at the back of the printer.

  2 unplug the power cord also from the wall...

  3. wait for two minutes.

  4 reconnect the power cord to a wall outlet first.

  5. hold the pound (#) and six 6 buttons.

  6. all by pressing the two buttons, reconnect the power cord to the back of the printer and at the end of two seconds, exit book and six buttons.

  7. turn on the printer if it goes out...

  Let me know the results.

• I get a message saying Lightroom met an erorr when reading the preview cache and need to stop smoking. Then told that Lightroom will try to resolve thei problem the next time it starts. Never does. Tried to uninstall and reinstall but no good.

  I get a message saying Lightroom met an erorr when reading the preview cache and need to stop smoking. Then told that Lightroom will try to solve the problem the next time it starts. Never tried to uninstall and reinstall but no good.

  Sound familiar to anyone?

  Hello

  Please go to the save location of the Lightroom Catalog and here please delete the Lightroom Catalog Previews.lrdata folder.

  Now please open Lightroom and check if it works.

  Please let us know if it helps.

  Kind regards

  Tanuj Sandal

• Photoshop CC 2015 (Norwegian version) will not start. The following message: Adobe Photoshop CC has stopped working.  A problem caused the program stopped fungeresom correctly. The program will be closed and you will be notified if a solution is av

  Photoshop CC 2015 (Norwegian version) will not start. The following message: Adobe Photoshop CC has stopped working.  A problem caused the program stopped fungeresom correctly. The program will be closed and you will be notified if a solution is available.

  reset your preferences-

  Acrobat: http://help.adobe.com/en_US/acrobat/X/pro/using/WS58a04a822e3e50102bd615109794195ff-7feb.w .html

  Adobe media encoder: https://forums.adobe.com/thread/1713540

  Legacy: http://helpx.adobe.com/after-effects/using/preferences.html

  Bridge: https://helpx.adobe.com/bridge/kb/troubleshoot-errors-freezes-bridge-windows.html

  Dreamweaver: https://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs6-cc.html

  Flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html

  Illustrator: http://helpx.adobe.com/illustrator/using/setting-preferences.html

  InDesign: https://forums.adobe.com/thread/526990

  Lightroom: https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html

  Muse (mac): https://forums.adobe.com/thread/1246022?tstart=0

  Photoshop: https://forums.adobe.com/thread/375776

  Photoshop elements: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html, http://www.photokaboom.com/photography/learn/Photoshop_Elements/troubleshooting/1_delete_p references_file.htm

  elements of first: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html

  First pro: http://www.mediacollege.com/adobe/premiere/pro/troubleshooter/trash-preferences.html

  If that fails, uninstall, clean (http://www.adobe.com/support/contact/cscleanertool.html) and reinstall

• Reboot and select good Boot Device problem - my PC does not start!

  Hi all

  Whenever I turn on my computer I get the message "Reboot and select proper boot device or Insert Boot Media in selected boot device and press a key.

  I checked the diagonistics material and these are the results:

  Test CPU-

  Hard drive: failure of the connection Test - Error Code: BIOHD1

  Memory - past

  I don't think that the issue is a faulty connection. My reason to believe so because I think that I had a virus on my computer (I was not able to confirm) I tried to delete the last time I was able to use the computer. Then I turned off the computer to restart, but unfortunately, that's when I got this error message.

  I had this problem once before (about 3 years ago) and I was not able to solve this problem, so I just stopped using the PC. Then one day my Dad turned on the computer (a few months later) and it worked all of a sudden.

  Anyone know what this problem is? How can I solve this problem?

  Any help is greatly appreciated! Thank you very much for your time and effort!

  Additional information:

  It was originally a windows 7 PC, but I have upgraded to windows 10, which is the current operating system.

  Product: HP p6620f

  I managed to start my PC again.

  I have unplugged all connections and left it that way for about 24 hours. Then I plugged everything back in and all of a sudden the PC worked again. I don't know if it will last, but right now it works.

  I'll write another post if something changes.

• Satellite Pro M10 suddenly stopped starting or to reach the POSITION

  Hi all, hope someone can help or advise me on what to do.
  My Pro M10 suddenly stopped starting or to reach the POSITION.
  When the switch is pressed, green light turns on and stays on and that of about it, no display and not even the rotation of the fan to the top. :(

  Funniest, it is the battery always fresh and is fine.
  As you know, this model is out of warranty now and I'm technically minded and disassembled laptops before so I don't mind open my machine.

  Just thought I would ask here first before doing so.
  Hope someone can point me in the right direction of what's wrong, have heard a rumor that the M10 with a video fault, but surely would not stop the machine POST'ing would still.

  Thank you very much
  JayZ

  Hi Jay,.

  Difficult to pin-point your problem remotely as you will understand, however, I expect the laptop either emit a series of beeps (in a type long, short of the boss) or else Flash HQ led to give some clues as to the reason for the failure of the POST.

  First I'll try to remove/replace the modules of RAM, hard disk and also the optical drive to see if it improves the situation. Otherwise, I would tend to suspect the motherboard failure.

  Kind regards

• receive a problem caused windows to stop working, will notify you if a solution is found. Display driver igfx has stopped.

  the computer, ups and stops working...

  on a number of occasions, I get a blue screen with a print so small, that I can't read. Receive message a problem caused windows to stop working, will advise if a solution is found. Display messages to receive driver igfx has stopped working.

  You should look at the web site of the manufacturer of your video card or monitor to see if they have updated drivers.

• After installing something from windows update my computer start Startup Repair each time and said "a hard disk problem is preventing Windows from start" and turn off.

  Hello

  After installing something from windows update (about 300 MB in size) my computer start Startup Repair each time and said "a hard disk problem is preventing Windows from start" and turns off.
  Then a window pops up saying "Startup Repair cannot repair this computer automatically.
  The details of the problem say;
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6001.18000.6.0.6001.18000
  Signature of the 04:65537 problem
  Signature of the problem 05: unknown
  Signature of the 06 problem: BadDisk
  Signature of the 09 problem: unknown
  Signature of the 10:1168 problem

  System Restore does nothing, and all the other tools of recovery. :(

  Please help, it will be much apreciated :)
  DOM

  If you are sure that the problems began immediately after installing a Windows Update, use the free support of MS here:
  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.  MS - MVP - Elephant Boy computers - don't panic!

• In Windows Media Player 11 when spend to add songs, how get the list to stop starting at the top?

  With WMP11, when adding pieces of the current reading library, I often change between two tabs. My question is every time I switch back to the library to add more songs, tab how can I get the list to stop starting at the top? I have a number of songs scrolling on there where I left last can be very inconvenient. I remember with an older version when you leave the library, that he would stay where you left it. Yet once, how can I stop the library always start at the top and instead pick up where I left off?

  Thank you very much

  Reinstalling wmp11

• I use Windows Live Mail for some time now without any problem, then today it just started freezing.

  I've been using Windows live mail for some time now with no problems then today it just started freezing. I open my mail box, receive mail, then I'm going to open a specific e-mail and it begins to freeze.  I have to close the program and start again and it then it freezes again.  Any suggestions?  I did a check for viruses on my laptop and it comes back clean.  Thank you!!

  All 'Live' programs have their own forums. The experts he can better help you.

  Windows Live Mail Forum
  http://www.windowslivehelp.com/forums.aspx?ProductID=15
  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA

• Chronic problem - Mahjong Titans will not start

  273 messages
   
       
  Chronic problem - Mahjong Titans will not start

  For several days, when I try from Win 7 of Mahjong Titans games, all I get is a brief hourglass and then nothing.

  I tried a boot minimum without result, off and then turn on the Mahjong, run sfc/scannow, memtest and after all this still the same short hourglass and then nothing.

  Here's the same last log. Maybe he can help find the problem. I hope of course.

  Thank you very much.

  Log name: Application
  Source: Application error
  Date: 14/11/12 14:22:38
  Event ID: 1000
  Task category: (100)
  Level: error
  Keywords: Classic
  User: n/a
  Computer: primary
  Description:
  Name of the failing application: Mahjong.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc9f5
  Name of the failed module: Mahjong.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc9f5
  Exception code: 0xc0000005
  Offset: 0 x 0000000000029425
  ID of the process failed: 0 x 870
  Start time of application vulnerabilities: 0x01cdc29d68531b40
  The failing application path: C:\Program Files\Microsoft Games\Mahjong\Mahjong.exe
  Path of the failing module: C:\Program Files\Microsoft Games\Mahjong\Mahjong.exe
  Report ID: a645a0d8-2e90-11e2-8026-0022686b32ff
  The event XML:
  
   
     
      1000
      2
      100
      0 x 80000000000000
     
      93552
      Application
      Primary
     
   
   
      Mahjong.exe
      6.1.7600.16385
      4a5bc9f5
      Mahjong.exe
      6.1.7600.16385
      4a5bc9f5
      c0000005
      0000000000029425
      870
      01cdc29d68531b40
      C:\Program Files\Microsoft Games\Mahjong\Mahjong.exe
      C:\Program Files\Microsoft Games\Mahjong\Mahjong.exe
      a645a0d8-2e90-11E2-8026-0022686b32ff
   
  

  273 messages
   
       

  The fixed!
  It was too simple.

  Not an answer as to what caused the problem or how to fix. I just copied the folder Appdata Mahjong since one my laptop at the place right on the offending machine.

  All is well now.

  Thanks anyway.

• How stop/start instance forms/States, servers, etc.

  Hi all

  I'm confused, which includes a fusion middleware.

  I installed weblogic, forms, and reports. These are the three elements that I need.

  The documentation says that the sequence is

  1. start weblogic

  2. start forms

  3. run the reports

  But I can't find any simple commands in google how these three components to start.

  But there is a lot of confusion command how to start the fusion middleware

  MW_HOME domain_name/user_projects/domains/DomainName/bin/startNodeManager.sh

  opmnctl startall

  opmnctl stopall

  opmnctl startproc ias-component = EMAGENT

  opmnctl stopproc ias-component = EMAGENT

  Are these forms and reports include process instance?

  Thank you very much

  JC

  Yes, Jc. You don't need to go to the url and run em. You can just use the controls on the main server.

  Kind regards

  Harsha

• MovieClip - problem with instance.play () &amp; stop()

  Hello, I'm trying to start and stop a simple animation.  I made a circle, converted to a MovieClip symbol named 'circle' and move it using an interpolation.  He stops and plays when I pass the "stop()" and "play()" or "this.stop ()" or "this.play ()" orders, but neither when I use "circle.play ()" or "circle.stop ()".

  I tried "insert the target path" and through "this.circle" but it still does not work.

  Any suggestions?

  If you named the movieclip 'circle', but you animate it in its parent timeline, then the circle itself has nothing to play.   It's Crafty why play() and stop() work because these are the commands for the timeline in which you put the code.   The circle movieclip should contain the interpolation of chronology, not be placed in it.

• Impossible to do a ping to or from new Linux instance

  I have 2 instances running Linux.  We're working very well.  I can ping to and from this forum without any problem.  I then copied this instance in the second instance.  This one is running.  But I can not ping to or from it.

  I looked at all the settings and all seem to be the same as the instance operation.  I even removed and installed NICs without any difference.

  Anyone with an idea of what to check next?

  JP

  Welcome to the forums!

  Check if two clients use the same MAC address as they were copied. You can watch in the prompt .vmx file.

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =