Problems to connect several devices to BEFW11S4 v4

Similar Questions

• I have a problem to connect several computers to my wireless D - LINK DSL-274 DR

  I'M ON WINDOWS VISTA

  As soon as we try to connect more than one computer, we lose our connection

  Hello

  1. don't you make changes to the computer until the problem occurred?

  2. you get any error message?

  I suggest you to try the steps below and check if it helps.

  Method 1: Try the steps from the link below.

  Network connection problems: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-network-connection-problems

  Method 2: Try the steps from the link below.

  Wi - Fi and in Windows network connection issues:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  For your reference: Setting up a wireless network: http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network

  Hope this information is useful.

• Problem with multiple display devices

  Hello

  I've recently upgraded to Adobe CC and I am trying to configure Edge inspect on my iPad and iPhone.

  I added two devices defined in the instructions, but when I try and get an overview of these two devices, I get the following message:

  Use of multiple devices is a feature of the version complete edge inspect. Upgrade now to connect several devices simultaneously.

  Does this mean I have to buy another upgrade to allow multiple devices to be viewed?

  Any help appreciated.

  see you soon,

  Blue-insurance

  Inspect edge has two pricing options, a free version, which only allows one device to connect to both, and a full version that allows an unlimited number of devices to be connected simultaneously. If you are already subscribed to the full version of edge inspect try to connect log out of the application of edge inspect and then again to solve the problem.

• Connection problem diagnosis - "the remote device or resource does not accept the connection detected.

  My computer is a Windows Vista Home Premium 32-bit. The problem occurred about 2 months ago, while he was still in Vista, but please note that I've upgraded to Windows 7 last night and the problem is always the same.

  My Internet Explorer, updates to the computer, iTunes and everything, EXCEPT my AOL, does not work. My connection says 'excellent '. (Hang everything on my laptop to my wireless are works fine, that my office is having this problem)
  When I click on Internet Explorer, it says "Internet Explorer cannot display the webpage", and when I click on "analyze the connection problem" said "problems discovered - the remote device or resource does not accept the connection detected.
  I talked to my internet provider Comcast all morning this problem: she said that his side internet connections work properly. She walked through me steps including reconnected the router cords, control the way in which the Internet is put in place and other things, but everything was how it was supposed to be. She suggested that maybe AOL could be the problem and to remove it because I used it, so I did, but nothing has changed. So then she told me to contact Windows... (not sure how to call technical Windows supports without having to pay $59?, but found this forum)
  Is anyone familiar with this problem and could you please help or at least point me in the right direction?
  In addition, please let me know if you need any other information on the problem.
  Thank you
  Lily

  Hello

  Try the steps from the following link

  http://support.Microsoft.com/default.aspx/KB/956196

• Windows has encountered a problem communicating with a device connected to your computer. Status: 0xc00000e9.

  * Original title: 0xc00000e9

  Hi all

  I had a problem - would be great if someone could help me!

  =====

  Windows has encountered a problem communicating with a device connected to your computer.

  This error...

  File: / Boot/bcd

  Status: 0xc00000e9

  Info: An unexpected i/o error has occurred

  ==========

  I press ESC = exit or enter = continue it tries to start, but eventually back to the black screen. So I can't pass this screen. I do not of hava a recovery for Windows disk... And the laptop is a Sony Vaio with Windows 2008. A couple of days, I have connected to my work through the laptop environment and forgot to close - battery went down--and now this...

  Can anyone help?

  Please see the message (response) by Afsal Taher:
  http://answers.Microsoft.com/en-us/Windows/Forum/all/new-computer-running-Windows-7-unexpected-IO-error/46b4fc7a-9a83-4db2-9a00-dca512797e61

• Windows has encountered a problem communicating with a device connected to your computer.

  When you start the computer laptop, windows Boot Manager appears.

  He reads

  Windows has encountered a problem communicating with a device connected to your computer.

  file: \Boot\BCD

  status: 0xc00000e9

  Info: an unexpected i/o error has occurred.

  When I I go through F8, safe mode, last known good configuration, running in debug ect mode.

  running in safe mode past with him, freezes for abit in the past to a black screen with just the cursor and the Center recovery running VAIO, last good configuration, known debug mode. This windows is loading files, then the windows boot screen were it freezes then goes to a black screen with just a cursor.

  Place the cursor, I am unable to do anything else on this screen.

  is it far from getting the laptop to function normally again or is it finally the end of his life?

  the laptop is a sony VAIO E series (VPCEA25FG) running under windows 7.

  Hello

  The error - an unexpected i/o error has occurred, status: (0Xc00000e9) is a material error in the BIOS of your computer.

  Basically, it's to tell you that the computer is not able to communicate effectively with the hard drive.

  Try the Startup Repair.  Startup Repair is designed to prevent a reinstall tedious to diagnose and repair problems that prevent Windows startup.

  To run the Startup Repair tool, see the links below for more details:

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  
  

  Startup Repair: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  I also suggest you to update the BIOS. Update the BIOS, contact the manufacturer of the system!

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  To ask your question in the Forum of Sony, refer to this link.

  http://community.Sony.com/?XID=M:header:eSupport

• Im having problems to connect my helmet at the entrance in front of my laptop, and I can't use my microphone, which says that the "device" is not connected.

  Hi im having problems to connect my helmet at the entrance in front of my laptop, and I can't use my microphone, which says that the "device" is not connected. What should I do? Thank you

  Hello

   
  1. have you checked the problem by plugging the headset to another computer?
  2. it worked before?
  3. What are you talking about ""device"is not connected?
   
   
   
  I suggest you to connect to another computer and check.
  Also check if the device is compatible with Windows 7.
  Reference:
  Windows 7 Compatibility Center
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/
  If it's compatible, perform the methods below
  If it is not compatible, see the following articles:
   
   
   
   
  What is program compatibility?
  http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility
  
  Make older programs in this version of Windows
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
   
   
   
  Method 1: Run the audio Troubleshooter and see if it helps.
  Open the audio playback troubleshooting utility
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter
   
   
   
  Method 2:
  Run the Fixit described in the article and perform the steps:
  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
  See also:
   
  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems
   
   
   
   
  I hope this helps.

• I just bought the app for photographers creative cloud when I try finally connect with PS CC, I received an error message that says "no detected subscription. I don't really know how to solve this problem, I used my Adobe ID to connect several times

  I just bought the app for photographers creative cloud when I try finally connect with PS CC, I received an error message that says "no detected subscription. I don't really know how to solve this problem, I used my Adobe ID to connect several times and it just still the same message.

  Your subscription to cloud shows correctly on your account page?

  If you have more than one email, you will be sure that you use the right Adobe ID?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  .

  If Yes

  Some general information for a subscription of cloud

  Cloud programs don't use serial... numbers you, connect you to your cloud account paying to download & install & activate... you may need to sign out of the cloud and restart your computer and log into the cloud for things to work

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  .

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• Problem with mobile MTP device connection of Samsung.

  Original title: Device

  I have problems with the devices. When I click my devices and printers, he claims that there is a problem with the driver for Samsung mobile MTP device but when I plug it costs and he finds all my photos. I tried troubleshooting and it says that there is a problem with the PnP device. What can I do to fix this? I have try the resolution of the problems, but it does not work. He also says that my pc Ethernet controller is not installed. Once, I tried troubleshooting but without prevail. If anyone can help with these issues it would be greatly appreciated. I tried a system restore, and it doesn't work anymore.

  Thank you very much

  Hi Chris,

  To provide the proper resolution, I would need more information on your side.

  1. which version of the operating system are you using?

  2. What is the brand and model of the computer?

  3. What is the exact model of the Samsung Mobile?

  4. what measures all troubleshooting have you tried?

  This problem may occur because of corrupted device driver.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  What to do when a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows7/what-to-do-when-a-device-isn ' t-installed-correctly

  Method 2:
  If the problem persists, try to install the latest driver for Samsung mobile device MTP on the manufacturer's Web site.

  http://www.Samsung.com/us/support/supportMain.do

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Win 7 USB connection problem disconnect/connect Cycl

  Is anyone else having problems with their Droid Turbo and a Win7 PC connection? I got my first camera at the end of November. When I initially plugged on my PC, the AutoPlay of Windows kept popping up window and the device would be cycle as if it had been disconnected. The AutoPlay window closes never alone, and I need to close from a few to several 10s of windows (based on how long I left it plugged in).

  I was able to get a stable connection after installing the Motorola Device Manager software.

  After a problem without report, Verizon has replaced the original phone with a new phone. The new phone is the same cycle of disconnection/reconnection anytime it is plugged. Software Motorola device Managger says that the software is up to date.

  I connected the phone to a Linux computer and had no problem copying files back. The connection is remained established until I got the USB cable.

  I rebooted the phone and the PC several times that I care to count.

  Also has anyone seen this problem? More importanly, does anyone have a solution?

  My phone (in MTP mode, without debugging) shows that the VIDID 22 b 8: 2ea4. On several occasions, I saw the PID also be 2ea5 and 2ea8. (Maybe it's with debugging on, perhaps a PTP mode).

  A few times, the device is presented as "Unknown device" with no details in the Device Manager.

  I plugged the phone in each USB port on the computer.

  If I knew that the files to remove from Windows to replace the driver I'd do it. If I knew that the right driver I tell Windows to use. So far I have not found one that works.

  Thank you

  James

  James best would be to connect the device in MTP, USB OFF debug mode. In Device Manager, locate the device and click on uninstall. At the prompt to uninstall to make sure that you CHECK DELETE the driver software. Uninstall device of motorcycle, bike mobility Manager drivers and nothing of another "bike Mobility" brand. I use a disc cleaner (ccleaner) delete left over remnants of uninstalled product files. I first do a system cache/clean and repeat several times until the cache gets up, nothing to remove. After that it's over, I run the registry cleaner. After scanning, select "Questions of difficulty" to the quick click reg backup YES, choose a SAFE place 'FIX ALL '. Once done, repeat until there are no more problems found. After all this is finished, STOP, do not restart. Computer to start up, run CCleaner again just to make sure everything is clean, so before you plug in your phone, go to and install Motorola Device Manager/USB Drivers. Let the full install and reboot. In developer options, revoke the authorization of debugging. Connect the phone in MTP mode to the PC and let Win7 to install the drivers. Change the connection of the device to PTP repeat, then finally change device USB debugging and let windows install the drivers. Let us know if this helped or hurt.

• When I have bad weather I lose my connection several times

  When there is a storm passing (on me or nearby) I lose my connection several times during the storm. I have Verizon DSL. Military have been repeatedly here, check my connections, connections to the outside on the poles, but never nailed the problem. They even ran a direct homerun to my DSL router/modem. Also during the game (UT2K4) my ping shot up to 988 several times. It gets very frustrating, especially when Verizon can't find something wrong. I'm the only one on this line. I have DishNetwork hooked to a modem, I think it is called Sling. Wi - Fi from the receiver to the Slingbox, then the Ethernet cable to a router/modem. May - so that it affects my ping? The router/modem would be bad? It's a westell 327W. I have a connection of Meg 7.

  If you connect your PC to your router/DSL modem via a wired connection and disconnect all other devices (wired & wireless), it would help narrow down if the problem is with your DSL service for your home or something in the configuration of your home. If your connection is OK like this, add devices to your LAN setup one-at-a-time to try to work out which one is causing the problem.

• Fusion 6.0.2 - cannot connect virtual device sound

  Hello

  I recently updated my system to a new Mac Pro (MacPro6, 1 - coffee can style).

  I have a pair of speakers connected to the line out on the Mac Pro, and his works very well under OS X.

  I use VMware Fusion 6.0.2.

  However, I feel a particular sound problem in all my virtual machines of Windows.

  When I turn it on, I get a notice indicating:

  Cannot connect virtual device sound because no corresponding device is available on the host.

  You want to try to connect this virtual device whenever you turn on the virtual machine?

  
  

  No Yes

  
  

  
  

  If I click No., I wonder what is new in an infinite loop.

  If I click Yes, Windows starts and the sound works, except that it comes out of the internal speaker on the Mac Pro, rather than the speakers on the line output.

  I have several virtual machines of Windows (XP, Vista and 7), and this problem affects all the.

  VMWare tools is updated in all virtual machines.

  All of these machines were copied from my old Mac Pro, for testing, I decided to create a new virtual machine from scratch.

  I used Vista because I had this .iso at hand.

  At the end of the installation, after installation of the VMware tools and all the virutal machine had no noise.

  Windows has indicated that his material is installed and the windows volume meter shows visually playback of sounds (this small sound level meter), but there is no sound will appear.

  After cutting this new machine virtual and going in the settings, I noticed that he had missed at what soundcard put out of SERVICE.

  I turned on and when I turned it on I got the same message and the same problem as all other virtual machines.

  I also tried to edit the .vmx to show sound.virtualdev = 'es1371'but this disabled sound totally.

  
  

  I'm at the stage of ideas.

  
  

  For any help or suggestion would be appreciated!
  

  Most Macs have built in the input device, so they list a 'internal' microphone as the default selected the input device. The end of 2013 Mac Pro is not a built-in microphone, so by default, it will show "no input device found. VM Fusion 6.0.2 does not seem to take into account the case where there is no device found entry. I consider this a bug, but you can work around it by adding any input device. For example, the "headphone" in the back the Mac Pro is actually a pair of entry. If you connect a headset, as what is delivered with an iPhone, then it will be displayed as an input device and the merger will stop at throwing the error.

  I hope that VMware solves this problem in an update.

• Hi I have a problem to connect on wifi I have reset all the setting ang simultaneously press the home buttom ang poewr but not wrking buttom, I can't and on the router because I was on a public area as hotel thank you

  I have 5 16 g model A1428 phone

  FCC ID * A IC * A IMEI; ***

  I TRY TO OPEN MY PHONE TO CHANGE THE BATTREY AND REMOVE THE LCD CABLE TO CHANGE THE POWER ON SWITCH, BUT UP TO THAT ONLY TO REMOVE THE LCD SCREEN, I GAVE ALL MY BECAUSE IS DIFFICULT... WHEN I PUT I CAN NOT CONNECT TO WIFI.

  I TRY to RESET all THE SETTING or RESET or PRESS TOGETHER HOME BUTTOM AND POWER SWITCH ONLY MARKET THE ROUTER NETWORK I can't DO it BECAUSE it OF in CRUISE BOAT or in public space...

  Thank you!

  ALFREDFROMTAGBILARAN

  < personal information under the direction of the host >

  Please do the following and after each test to see if the problem is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Please see recommended settings of WiFi routers and Apple access points
  4. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  5. Settings - WiFi - < network name > - Click on forget network - do a restart forced 4 and then again add the network
  6. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  7. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  8. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  9. Backup the device to iTunes - restore as NEW (no backup) using iTunes - see if solves problem - if yes - restore backup
  10. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• Twinning/incoming connection unpaired device

  I found an "abnormal" behavior I describe below:
  . Connect a headset BlueTooth on your computer.
  . Once it has been done successfully,
  . Disconnect the device (headset).
  . Then, remove the device from the list of devices on your computer.
  . Now try to connect your device to your computer FROM your device.

  -Online PIN code is requested, but the profile never appears in the
  List of computer devices and the connection fails.

  No information on this issue?
  Is there a something to do to make it work?

  This was found on Toshiba BlueTooth stack 4.20.08 (and previous 3.0.3)

  Hello

  I use BT 320 Plantronics headset with my laptop and I can tell you just that configuration is very simple and finished in one minute. Since then, I simply use Plantronics shortcut on the desktop and can use the headphones without any problem.

  I put t know why I should remove device from the connections list. If I do that I have to configure the connection whenever I want to use.

  . Then, remove the device from the list of devices on your computer.
  . Now try to connect your device to your computer FROM your device.

  Sorry, but this way of using peripheral BT is for me unusual. When BT device on your laptop is enabled start Bluetooth settings and create the new connection. Every time when I want to use the BT headset, I do follow the steps:
  -Device of BT and activate BT on the laptop
  -Double-click on the shortcut created to BT headset
  -Portable contact BT and I must press helmet itself to establish a connection
  -After made this sound on the laptop are completely disabled and every sound produced on the laptop I hear BT headset only

  All that s! I can't launch connectivity BT headset JUST to center of notebook BT (BT settings double click on the BT symbol in the taskbar).

• Best way to connect several hard disks

  HI - since getting my new Mac Pro, I worked with two hard drives of 12 to promised Pegasus 2 Raid-5.  They have been great.  But my video player started to get crazy and so I bought two backup drives WD - 8 to, one to save the key on each PP2 files.  Unfortunately, it was too late to save the video player, as one of the bays failed.  Because it's Raid-5 and with the amazing and patient Vincent promise eSupport, I replaced the failed drive Bay and am now waiting while he rebuilds (if all goes well, without any loss of data).  Then it will get saved.

  Until it became clear that a bad drive Bay was probably underlying computer freezing, loss of images in video playback, etc., I was wondering if there was some sort of best practices for fixing of external drives.  With Thunderbolt, you can chain; But what to what?  Is there a limit any?  Can I plug two disks promise, then the one closest to you on the computer?  Must the WDs be connected in the same way, each to each, and the other to the computer?  Should there be just a Garland of four disks?   ????   In the old days, you had to look at how much energy was used during the USB and Firewire connection, but the true even for love at first sight?

  Surely you'd be recognizing any indication on how best to connect several hard disks.

  Thank you!

  There are 3 unique bus in the Mac Pro black cylinder. Better reactivity is with your readers spread between three buses, keeping in mind that video display takes nearly half a ThunderBolt Bus itself.

  You can use USB-3 for your backup drives - just keep in mind, it is only a sufficient bandwidth behind the USB to operate a chain of reading and writing of full tilt. If you simultaneously use devices more than that, you can start to see some cuts of your maximum transfer rate.