Problems with CD-ROM readers

Similar Questions

• Problem with DVD - ROM SD-C2402 (DVD multisession)

  Hello

  I have the following problem: I recorded a DVD in different stages (multisession) with Nero 6, but I can read only the first session on my laptop (Windows 98SE). On the other hand, I have no problem with multisessions CD

  Could you help me in this case?

  Thank you

  John

  Hello

  I m not 100% sure, but I think that it s a problem with the burning software and/or the media. I found information there are many problems with playback of the files after burning the multisession DVD-R, + R (Win98SE). In my opinion, you should try to burn DVDs on media RW multisession.

  Good bye

• Sierra / problem with network Synology readers

  Hello

  because Sierra was released, I discovered a few questions on the Synology network drives. If I want to change some JPG to disk for example turn them or what ever Finder will immediately freeze and con ' t not be restarted! Side Synology always the last relase is installed - on Yosemite / El Capitan, it works great!

  Someone you have the same problem?

  Apple recommends against the use of network drives.

• Satellite P10 problems with Mat * a DVD ROM

  Hello

  I have a problem with my P10,
  I bought it for 2 months and 4 months ago my
  Carpet * a DVD ROM does strange things.
  When I try to copy a CD for example, it reads the cd source, after I put in those recordable, it starts to burn and suddenly it stops, says ERROR (Event Viewer: error on Controller\Dev01\CD-ROM) and my Combo drive is presented as a 'simple' DVD - RAM on Solution Explorer drive.

  Sometimes it won't read movies on DVD or CD so I have
  to restart the P10 and generally it can read the disks after that.
  So is my faulty drive, the card mother or just me?
  Have been looking for a new driver, but there is just a
  DVD-RAM, no driver for the drive itself.

  Hello

  Maybe the contact of the cable to the controller and CD player is loose. The error message said you it should be good!

  Your P10 is under warranty so bring a call Toshiba and it need to be repaired or a Service partner!

  Hans Bye

• Pavilion Elite HPE-170 t: problem with the new HP DH16D5S DVD ROM drive

  My office is a HP Pavilion Elite HPE-170 t.  I recently upgraded from Windows 7 to Windows 10.  I have two HP optical dirives, one is a writer, and the other is just a DVD ROM  Both have always worked perfectly with Windows 7.  After you have installed Windows 10 continuous burner work very well works correctly with autoplay.  However, the DVD - ROM, HP DH16D5S, immediately began using autoplay.  Actually the drive was not yet recognized as a drive when you view the drives in the file Explorer.  Finally, it would seem, sometimes taking also longer than 5 minutes or more before doing so and then would work very well.  I tried different types of media, including music CD, DVD video and DVD software with the same results.  I assumed that it was a problem with the drive, maybe a bad capacitor, etc., which was originally not start correctly.  So I ordered a new DH160D5S, but which seems to have been a waste of time and money, because it does exactly the same thing as the original.  I even changed the cables autour between it and the burner, but it made no difference.  The burner still works fine but not DVD ROM.  I tried to find a more recent driver for it, but had no chance.  I found on a Dell website for this drive which was an update of the firmware for Windows Vista and Windows 7, but not for Windows 10.  I advanced and downloaded, but when I tried to run, I got the message: "your system does not meet the minimum requirements for this update.  Update has been canceled. »

  I want to try a different brand of DVD ROM, but would have to buy one without knowing if it would help.

  Any help will be appreciated.

  Since I posted this message I discovered that there is a driver problem with this DVD ROM.  There's no driver available yet to make the drive compatible with Windows 10.  Since then, I returned the drive and replaced by another brand that is compatible with Windows 10.

• problem with the CD/DVD ROM device

  Windows nofified it is problem with my CD ROM havin - two of them! I tried Windows troubleshooting. He tried to reinstall the driver but it failed.
  Then I tried Windows Update to see if I can find an update of the driver but he could not find any update related to my CD ROM
  Now I don't know wt to do at all!

  Hi khadija.

  1. you receive messages or error codes?

  You can read the following article and see if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Hope this information is useful.

• Problem with Dell Latitude 2100 (with windows vista) is a driver (file: \windows\system32\drivers\msahci.sys) catch 22, it's that it doesn't have an internal cd-rom

  I have a dell latitude 2100 and when it is consumed first upward it goes to a screen of security and said that is wrong and it is said that the status of this file is 0xc000000f how I could fix this without an installation disk because it does not a cd-rom

  Hi Rick,

  Thanks for posting your query in Microsoft Community!

  The description of your problem, you are facing problems with your Dell Latitude 2100 and receiving tell them an error message which is bad and he said that the status of this file is 0xc000000f. In order to quickly provide a solution, please answer these questions:

  1. What is the exact error message with error code?

  2 did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you check the drive for errors, and then check if it solves the problem.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

   

  Important: While running chkdsk on the drive, if bad sectors are found on the hard drive when chkdsk attempts to repair this sector, the data available in this area may be lost, and it is not recoverable.

  Method 2: Try the SFC (System File Checker) scan on the computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Note: It may prompt you to insert the Windows installation disc. However, you can use the external DVD player and check.

  Hope this information helps. Answer please if you have any additional questions about the problem you are having and we will be happy to help you further.

• problem with write access to truecrypt readers windows 7. The mounted drive is not writing priveliges. Read-only. Cannot change in the security permissions.

  problem with write access to truecrypt readers windows 7. The mounted drive is not writing priveliges. Read-only. Cannot change in the security permissions.

  Hi amcop4591,

  1. How is - that Mount you the drive on the computer?

  2 Di you use any third-party tool to mount the drive?

  I suggest that you remove the external drive using the disk management and check back later if you can change the permissions on the drive.

  If you change the permissions, make changes to the permissions on the drive and then mount the drive.

  Mount or dismount a drive

  http://Windows.Microsoft.com/en-us/Windows7/mount-or-dismount-a-drive

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem with the CD ROM TSTcorp CDDVDW SN-208BB on SAMSUNG NP300V5A-A03US

  My CD Rom has problem with TSTcorp CDDVDW SN-280BB. Can you please provide assistance? Thank you in advance.

  Try to remove the entry from the Afc that relates to afc.sys.

  To remove the Afc entry double-click LowerFilters and, under value data, delete afc > OK

  Create a System Restore Point beforehand and restart the computer later.

• I think that there is a problem with the cache, Rom or bios

  everything changes every time I start windows, for example I must maximize the window workstation, every time I start the pc in my previous pc once I expanded the window and I closed the windows recognize my choice "maximise window" and the window opens always maximized... also in programs like photoshop the program changes the interface whenever I turned off the pc and open it

  Hi Marc,

  Write us with the following details so that we can better help you.

  ·          What changes do you see in the interface of Photoshop?

  There is no problem with the BIOS ROM or with the cache. I suggest you follow the steps below.

  (a) open a Windows Explorer, optimize it click on the arrow next to the button of the view on the toolbar, and then choose a display setting.

  (b) on the toolbar, click organize, and then click folder and Search options.

  (c) in the folder Options dialog box, click the view tab, click apply to folders, click Yesand then click OK.

  Write to us with the details asked. We will help you to come.

• Problems with my microsoft cd-rom

  Ive had recently problems with my microsoft cd-rom, specifically the driver. It indicates that the driver is corrupted or missing (code 39)

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  {Unable to load device driver}
  HS device driver could not be loaded.
  Error status is 0 x %x

  Ive tried to uninstall it, install the system reset several times, and a few other methods but it is not fixed

  If someone could help me it would be appreciated

  You can check the following registry key? :

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  To the registry for this key, in the right window, in the world is here, under 'Name', a LowerFilters and UpperFilters value?

  If so, for UpperFilters and LowerFilters, value which is listed under "data"?

• Problem with flashing Boot ROM

  Hey everybody

  I have a problem with my Slate7 4600, everything was fine this morning with it up to what I have turned off for awhile

  When I turned it on again, the HP logo that appeared, followed by a black screen.

  So I tried to reflash the recovery Image on the HP site via sideload ADB (the only thing that I have access to) but when checking the update file I get this error:

  Spoiler (Highlight to read)

  assert failure less_than_int ro.build.date.utc

  assert failure less_than_int ro.build.date.utc

  So now I'm stuck with this, kernel starts, but Android does not work (I think), and sideload won't let me flash zip.

  Thanks in advance!

  Ok thank you. Have you tried to update the version.14 I see out there? It is possible that if his treat them as updates that it will not allow the same generation that is on the device to be flashed, it must be more recent.

  There are ambiguities on the pages of software support if the files are updated or images of the recovery. I'll see what I can do to clarify that.

• Problem with HP CDDVDWTS-L633NSATA cd rom Device Driver

  I have a laptop HP G61-631NR my operating system is Windows 7 64 bit and there is a yellow triangle with an exclamation by my pc device icon indicates he needs in the event of problem and after bad shot the message I get is in the subject line.

  It of usually a known software conflict and is going through the Board of Directors will all computer makers due to a problem with several media burning / ripping applications being installed on your system.

  You can run this file, go online to the Microsoft site for a patch or fix it manually by following the instructions below:

  Manually remove the registry entries

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• Removal of security icon to remove a mounted cd/dvd drive that can not be delete. also the problem with the apple driver.

  Vista Home premium

  64 bit

  HP pavilion dv4-1220us

  It happens when I went to open I tunes and he indicated a problem with the cd/dvd and then I noticed security remove the icon at the bottom of the screen, attended safe remove and it delete my CD-ROM drive mounted cd/dvd look no further and I notice this driver is part of apple who was a pilot of speed indicating this driver will remove your drive of cd/dvd rom IS NOT WORKING WITH some programs installed.  I contacted apple, we have deleted the driver and complete the process with the driver of the machine. Now, this does not take care of the security delete icon then tech apple tried to help and communicate with Microsoft or hp.

  RESTORE MY COMPUTER SEVERAL TIMES, THIS ICON IS STILL THERE.

  DOWN MY BIOS AND THE ICON IS STILL THERE.

  THIS SCANNER DRIVER AND THE ICON IS STILL THERE.

  Security delete icon States: remove TSST CORP CD/DVD TS-L633L ATA DEVICE READERS of CD-ROM/DVD-ROM if I hit remove it will remove my CD/DVD-ROM DRIVE.

  I went on my computer and click on my cd/dvd rom drive and went to properties and that's what I found below.

  1. FUJITSU MHZ2250BH G2 ATA HARD DRIVE: WENT INTO PROPERTIES TO DISPLAY DRIVERS, IT HAS A HPDSKLFT. SYS DID NOT SIGN THE OTHER TWO DRIVERS ARE THE SIGN. ENTERED DRIVERS FILE AND INSTALLED THE SIGN AND IT IS SHOWING NO SIGN, ALSO WITH HP ASSIST THIS HARD DRIVE IS DISPLAYED AS 0 FAILURE AND DISK.

  2 TSST CORP CD/DVD TS - L633L ATA DEVICE DVD/CD-ROM: ENTERED VIEW PROPERTIES PILOTS AND THIS ONE HAS THE DRIVER OF THE VEHICLE AND A DRIVER.

  At the moment I'd hide so I does not uninstall my cd/dvd drive.

  Do I need another hard drive?

  Is this something with the Bios?

  Apple has tried to help with this driver of train that I'm not sure that this problem is still with this gear or what?  This is the site about the problem to apple and the site of heavy plant driver.

  http://www.GearSoftware.com/support/drivers.php

  http://www.GearSoftware.com/wiki/index.php?title=CD/DVD_drives_disappear_after_installing_iTunes

  http://support.Apple.com/kb/TS2308

  http://www.GearSoftware.com/wiki/index.php?title=drivers:_Windows_ - _Updating, _etc, _64_bit_versions, _removing

  Hi Mamalasting,

  I'd say Hewlett-Packard to visit support website and check if they have the latest drivers for the DVD player.

  Reference:

  http://www.HP.com/#support

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• problem with my cd/dvd drive... pls help!

  I have windows 7 ultimate! I have problem with my hard drive! I use lg drive and all of a sudden it reads only the CD-ROM and the dvd rom no! its disturbing me a lot! pls help! Thanks in advance

  Hello

  Having too many CD/DVD programs can cause strange problems, especially if they're loading of parts of
  themselves at the start because they will be competing for resources. This does not mean that this issue has been
  caused by those, however, it's a possibility depending on which and how many you have installed.

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  -------------------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">