Problems with the screen capture function

Similar Questions

• Satellite Pro L20-someone ' one can tell me if I have a problem with the screen?

  Hello

  I have a Pro L20 - PSL25E and I recently had problems with the screen, it was intermittently flickering/lose color and whiting almost (when the color fades white vertical lines begin to appear).
  This seemed to worsen after that I dropped it (only from about 2 feet off the ground, not a big drop).

  I thought that the sceen can go, but the performance of the laptop seems to be affected when this happens, the laptop started to run very slow (tracks mouse slowly, programs I clicked take ages to run and it freezes sometimes to stop flashing) that had me thinking that it might be a virus or performance problem.

  My screen, drivers are updated, I did a full scan with McAfee, ran a clear-up system and a Defrag.

  I was wondering if anyone knew if it seemed to be a problem with the connections of the screen and would need replacement or if it could be repaired or if it were a performance problem?

  Any help would be great thank you appreciate!
  Rebecca.

  Looks like the graphics chip has a problem, which I think is a motherboard replacement.

  You can get a quote for repair to an authorized service provider. There is a list of ASP on the Toshiba site.

• Problem with the screen on IPAD curtain

  Hello

  I'm a bad psychic, and I have a problem with the screen curtain.

  A longitudinal of Voice Over, the screen curtain is automatically activate.

  Normally to turn it off, you must type three times with three fingers. Only on my IPAD when I type three times with three fingers is "saying that turns off or preach. Find it me impossible to disable the screen curtain when voiceover is active.

  The latest version of IOS 9.2.1 is installed.

  I reset the Ipad and nothing changes.

  Can someone help me?

  Thank you

  Is is possible that the zoom is also on your iPad? If this is the case, try to use a quadruple 3 finger tap to turn off screen curtain.

  If the zoom is not active, try:

  1. Possessing the sleep/wake and home button until the Apple logo appears or 15-20 seconds.
  2. If, you can't remove the curtain of the screen, I would advise you reset the settings of the iPad. Settings > general > reset > reset all settings. It will be his turn VoiceOver off, but then you can use iTunes to turn on VoiceOver. Voice-over should return without the curtain of the screen automatically active. IOS - Apple Support using accessibility features

  The of is it possible that zoom is also active your iPad? In this case, you must use a valve 3 quadruple finger pour disable the screen curtain.

  try if the zoom is not enabled:
  1. While holding the button market / sleep and home to ' to the Apple logo, or 15-20 seconds.
  2. If you still can't delete the screen curtain, I recommend to RESET the settings on the iPad. Settings > General > RESET > RESET all settings. This turns off VoiceOver, but you can then use iTunes to turn on VoiceOver. Back to turn voiceOver should without the curtain automatically active screen. Use IOS - Apple support accessibility features

  -AJ

• ThinkPad X 230 Windows 7-64: problems with the screen after updates

  Hi all

  I have a problem with the Thinkpad X 230. After a recent update of Windows 7 (64-bit), the screen resolution is set to 800 x 600 and brightness to the minimum. FN + F8/F9 does not work. The brightness is uncontrolled. I had to restore the system before the update.

  How to solve the problem, do anyone know?

  Thank you!

  Isosik

  Hi Isosik,

  Welcome to Lenovo Community!

  According to the request, we understand that you are facing problem with the display resolution on your ThinkPad X 230.

  If you have updated the drivers from Windows update, sometimes this kind of problem occurs with windows generic drivers for cause of driver incompatibility, suggest always update drivers only via the ThinkVantage System Update utility. Update only the application of Microsoft Windows Update.

  You can also manually download the drivers from the Lenovo support site.

  Lenovo support site.

  I hope this helps.

  Best regards

  Agnes Kumar

• I'm having a problem with the screen resolution cannot be superior to 800 x 600 pixels

  All this began after I plug an i9 phone to my pc to load

  later, to this day, when I turned on my pc screen resolution would not stay how I put it

  He wants to just go to 800 x 600 pixels.

  I ran microsoft security scan it found and deleted a virus java exploit cve 2010-4452

  but still having trouble with the screen resolution

  If the problem occurred after you plugged into your phone. I suggest to perform a restore of the system automatically, put it on a date 2 days before you had the problem. If this isn't the case, you can check the video card driver:

  Start > run > devmgmt.msc
  Check your video card driver or see if there are any missing drivers
  If its lack, then update or install the driver of your video card.
  I hope this helps you! Good luck.

• Problem with the screen size of my application in the emulator for BlackBerry 10

  Hello, I have a problem with the emulator for BlackBerry 10 and is as follows:

  When I run my application in the emulator waving, sounds good and all content is complete, however, when I run the application in the emulator for BlackBerry 10 soft looks as if she had a zoom very large level of predefined way and only see a part of the application.

  With controller emulator, I have changed the level of 70% zoom, but still does not work.

  Here, I'm posting two photos:

  

  

  One future half-assed answer

  var dpr = 1; // To set the meta on a real device to get 1:1 pixels
  
  if(typeof window.devicePixelRatio != 'undefined') // Does device support devicePixelRatio?
      {
      dpr = window.devicePixelRatio;
      }
  
  if(dpr) // Set up the right meta
      {
      var meta = document.createElement("meta");    meta.setAttribute('name','viewport');
  
      meta.setAttribute('content','initial-scale='+ (1/window.devicePixelRatio) + ',user-scalable=no');
      document.getElementsByTagName('head')[0].appendChild(meta); // Inject meta
      }
  

  This works perfectly, but must be placed in thethe document FIRST and foremost

  Live JS is used to avoid problems of library management

  It won't work in Wellington but works perfectly on all devices I've tried

  As mentioned in the code above just packaging needs in the script tags and setting very high index.html HTML code as you can get - right after

• problem with the screen savers

  OK, I have windows 7 Home premium. Now, when I download a screen saver. I end up getting an error message. And I want to know how I can solve this problem. Or if I can fix it. I'll post the error here. Thanks in advance.

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: nfsRainbowAbstraction.scr
  Application version: 4.0.0.0
  Application timestamp: 4b0041b4
  Fault Module name: Flash32_14_0_0_145.ocx
  Fault Module Version: 14.0.0.145
  Timestamp of Module error: 53aa18ec
  Exception code: c0000005
  Exception offset: 001fbb14
  OS version: 6.1.7601.2.1.0.768.3
  Locale ID: 1033
  Additional information 1: dcdb
  More information 2: dcdbdf2902fa28773ce6a482d2712212
  3 more information: 9da6
  Additional information 4: 9da622ac40664012d59c7c96b3c0c476

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  Flash screen saver function?  Could be some screensaver you downloaded was made for a version MUCH earlier third Adobe Flash Player and/or the operating system.

  When I tried to go to the web page where you can get this screen saver (nfsRainbowAbstraction.scr) - my eSet NOD32 antivirus and Malwarebytes warn me constantly bad things even. Heh

  In other words - if work of other screen savers (i.e. - those of integrated)-the issue is either with (in this case) the Adobe Flash Player this screensaver uses or the screen saver itself.  Communicate with those who have made the screen saver.

• IPhone update (but an old having problems with the screen Activate iPhone and Apple ID)

  I have an iPhone 5 that, by chance (Pocket escaped), is stuck on the screen of the iPhone 'Find your phone' Activate.  The iPhone does not accept my Apple ID.  He is looking for an address icloud.com.  I can't honestly remember a set up, and I tried a number of variations on the icloud.com address (using the 'index' system provides) and passwords with no luck.  Do not have any problems with my Apple ID - I can see my phone & details on my screen of the user, when I connect my account (via the office).  Subject to my cellular service provider, I tried to force a restore on the phone via iTunes, but after that he asked me a few questions of initial Setup, I'm just at the "Activate iPhone" screen

  To be honest, I was going to pick up a new phone this week anyway.  My concern is now that I don't want to not suddenly faced with the same problem.  This lock, I meet - is - this quite specific for the phone itself? If I get a 6 plus and use this Apple ID to activate it, I ask in trouble? I admit that I am a twit when it comes to activation codes, the Apple ID, SIM cards and others.

  It was my first smartphone (+ 3 years now) and the installer was made by my employer, so strange things could happen at the beginning.

  Thank you all for any help

  If the implementation was made by your employer, they can put in something different from your Apple ID to find my iPhone. It also seems that if something was damaged in the fall. Who can contribute to the problem.

  If, when you receive your new phone, you make sure you use your Apple ID to find my iPhone, you should have no problem.

• Problem with the screen when it rains it is wet

  Hello world
  Any of you had a similar problem like me?
  I noticed this before, when the screen is wet or raining on her is pushing screen by itself.
  At first I thought it's because problem of protector of screen, but 3 days ago when it rained, I wasn't able to use my phone at all, and I needed to call so consider screen protector, but the problem was still there.
  Like water proof phone that this should not happen.
  Is there a problem like that with my phone only?
  Should I inform Sony about this and send for repair?

  When the device comes into contact with water, the touchscreen misbehave. It's normal, that's why you have app touch block to take pictures under water.

• BlackBerry Smartphones having HUGE problem with the screen

  Please help me people... My flipberry went completely crazy...
  I ' l try to explain the problem with as much detail as I can remember...
  Since last week or both internal as external screen my phone acted crazy...
  for the start of a few days, the problem started with the internal display will red sometimes, or show the half of the screen with stripes of colors... I thought it was a passing phase...
  but after a few days, the screen went completely black... both screens external and internal... until this time, as I ran the firmware 4.6.0.222
  so that day I sat down and wiped my phone completely and loaded the latest firmware 4.6.0.236... in order to completely black screens are returned to the way they were... sometimes ok, sometimes showing abstract things and weird colors...

  and even today both screens went completely black... so I'm currently trying to get back to the 4.6.0.180 version as recommended by t-mobile...

  and I have not dropped my phone once again since I bought it 4 months ago... need help

  usually the phone will come with a free warranty of one year.  The best thing I can suggest is to return to the top of any data you left phone and bring it back for a replacement or sent it to be repaired because it seems to me that your phone is defective.

• Problems with the screen resolution, Cloud based software and Photoshop after the last round of updates Windows 8.1.

  Original title: screen resolution problems.

  Since the last series of Windows 8.1 update the resolution of my monitors has been changed for the worse. I use an AOC 2367 M (resolution 1920 x 1080) as my first monitor and a 42 inch Sony Bravia (resolution 1920 x 1080) as my 2nd monitor. The changes are more noticeable on the Sony Bravia and any adjustment I make to the resolution only make worse it.

  I also have problems with some software clouds as I load using citrix and when I try and navigate once opened software, I can't because the pointer selects a point about 50 mm on the side of the where he is hovering. In fact it is very difficult to open and close as anything and I resorted to the laptop to get concrete results.

  Photoshop now also comes up with a message when I open it up to inform me that the monitor profile seems to be defective.

  Any suggestions would be helpful as I thought initially an another upgrade must follow to correct the ills of windows 8, but appears not to have happened.

  Hi Joseph,.

  Thanks for the reply.

  Method 1:

  I suggest you to download and install all Windows updates available including optional updates. You can also install the latest device drivers for all devices including display drivers and monitor drivers on the manufacturer's Web site.

  http://eSupport.Sony.com/Perl/select-System.pl

  http://www.aocmonitorap.com/root/ANZ/download_driver.php

  Method 2:
  Adobe Photoshop CC version 14 is compatible with Windows 8.1. See Windows Compatibility Center for more information. To solve the problem with Photoshop CC, I suggest you try the procedure described in the article and see if it helps.

  Cloud applications help creative /CC crash immediately after launch
  http://helpx.Adobe.com/Photoshop/KB/CC-applications-crash-immediately-launch.html

  If the problem persists, I suggest you to contact the Support from Adobe.

  http://helpx.Adobe.com/contact.html

  To solve the problem from software hosted accounts, you may need to contact the Support to count.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Problem with the assignment of functions to the keyboard. Help, please!

  Hello
  
  I'm trying to get the help of the keys on the keyboard to control the navigation of the timeline. I use the code AS3 work the first time, but a little crazy then past and stops working for some reason any. You are supposed to be able to navigate along the timeline with the arrow keys (go back)
  
  I'm sure there is an easy solution to this problem but I am new to AS3 and it cannot know.
  
  Any info would be greatly appreciated.
  
  See you soon.

  Code on the first frame of the timeline (left label)

  Stop()

  stage.addEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_3);

  function f1_KeyDownHandler_3(event:KeyboardEvent):void

  {

  switch (event.keyCode)

  {

  Case Keyboard.LEFT:

  {

  gotoAndStop ('Center')

  break;

  }

  Case Keyboard.RIGHT:

  {

  gotoAndStop ('left')

  break;

  }

  }

  }

  Code used on the fifth framework of timeline (Center label)

  Stop()

  
  

  stage.addEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_2);

  
  

  function f1_KeyDownHandler_2(event:KeyboardEvent):void

  
  

  
  

  {

  switch (event.keyCode)

  {

  
  

  Case Keyboard.LEFT:

  {

  gotoAndStop ('left')

  break;

  }

  Case Keyboard.RIGHT:

  {

  gotoAndStop ('right')

  break;

  }

  }

  }

  Code used on frame timeline tenth (good label)

  Stop()

  
  

  stage.addEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_3);

  
  

  function f1_KeyDownHandler_3(event:KeyboardEvent):void

  
  

  {

  switch (event.keyCode)

  {

  
  

  Case Keyboard.LEFT:

  {

  gotoAndStop ('Center')

  break;

  }

  Case Keyboard.RIGHT:

  {

  gotoAndStop ('left')

  break;

  }

  }

  }

  You must remove the earphone prior actions such as:

  Stop();

  stage.addEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_1);

  function f1_KeyDownHandler_1(event:KeyboardEvent):void
  {

  switch (event.keyCode)
  {

  case Keyboard.LEFT:

  {
  stage.removeEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_1);
  gotoAndStop ('Center');
     
  break;

  };

  case Keyboard.RIGHT:

  {
  stage.removeEventListener (KeyboardEvent.KEY_DOWN, f1_KeyDownHandler_1);
  gotoAndStop ('left');

  break;

  }

  }
  }

• Problem with the screen blend mode

  Hello

  I noticed that the screen on my Illlustrator a blend mode problem, he does not let the color when the shape is black...

  Here is a screen for the explanation:

  

  (overlay = screen in french)

  I don't understand what is happening... ID do something wrong?

  EDIT: I use Illustrator CC (2014)

  What document color mode?

  In CMYK mode, you might want to try a (very) rich black.

• Problem with the CAE policy function

  Hi all
  I'm trying to set the tables of data with the DTV and get "ORA-28112: cannot run the political function" error when I query the table.
  ---------------------------------------------------------------------------------------------------------------------------
  -My diagram is "sales".
  grant Ridge no matter what context of balances;
  
  -created the context by using this statement
  create or REPLACE context sales_APP_CTX using PKG_SECURITY ACCESSIBLE on a GLOBAL scale;
  
  -Package specifications
  CREATE or REPLACE PACKAGE PKG_SECURITY
  function vpd_sec_pol_func return varchar2;
  procedure set_sales_app_context (p_user varchar2, p_security_level varchar2);
  end;
  /
  
  
  -package body
  CREATE or REPLACE PACKAGE BODY PKG_SECURITY
  ---------------------------------------------------------------------------------------------
  function vpd_sec_pol_func return varchar2 is
  
  -v_user varchar2 (100): = UPPER (portal.wwctx_api.get_user);
  Start
  If not for the user ("SALES", "ORACLE") then
  return ' State in (select State from app_user_states where user_id = sys_context ("SALES_APP_CTX", "APP_USER"))';
  on the other
  Returns a null value.
  end if;
  end;
  ---------------------------------------------------------------------------------------------
  procedure set_sales_app_context (p_user varchar2, p_security_level varchar2) is
  Start
  DBMS_SESSION.set_Context ('SALES_APP_CTX', 'APP_USER', p_user);
  -dbms_session.set_context ('SALES_APP_CTX', 'SECURITY_LEVEL', p_security_level);
  end;
  ---------------------------------------------------------------------------------------------
  end;
  /
  
  -The policy has added to the table
  Start
  dbms_rls.add_policy
  (object_schema = > 'SALES')
  object_name = > "SALES_SUMMARY"
  POLICY_NAME = > "SALES_SUMMARY_POLICY"
  function_schema = > 'SALES. "
  policy_function = > ' PKG_SECURITY. VPD_SEC_POL_FUNC',.
  statement_types = > 'SELECT, INSERT, UPDATE, DELETE.
  update_check = > TRUE);
  end;
  
  -I was able to put into context using sqlplus in running the procedure
  exec ('TEST_USER', 'R') PKG_SECURITY.set_sales_app_context;
  ---------------------------------------------------------------------------------------------------------------------------
  
  What I am doing wrong?
  
  Thank you

  Hello

  ORA-28112 only tells you that there is real error messages in a trace file on the database server. I forgot if the trace file is generated in the bdump or udump directory. Post messages.

  The political function should look like this:

  FUNCTION policy_function (object_schema IN VARCHAR2, object_name VARCHAR2)
          RETURN VARCHAR2 
  

  You don't have to use the arguments (I do not usually), but they have to be there. The system will call your function with two arguments of VARCHAR2, so he must accept two arguments of VARCHAR2.

• Problem with the Screen class

  Hello

  Please anyone suggest me that I had made an application for blackberry strom 9500 when I got extends the class of devices back button screen is disabled automatically. and when I extends the class screen it works correctly.

  I don't think that the class screen itself has the feature to close the screen when you press the ESC by default. If it isn't and you want to use it, you can pass the DEFAULT_CLOSE style to it.

  public class MyScreen extends Screen {     MyScreen(Manager m)     {          super(m, Screen.DEFAULT_CLOSE);      }
  
      protected void sublayout(int width, int height) {        // Add sublayout logic    }}
  

  Documentation: http://www.blackberry.com/developers/docs/5.0.0api/net/rim/device/api/ui/Screen.html#DEFAULT_CLOSE

  Is there a reason that you are using the Screen as opposed to screen or full screen class?