Problem with the screen when it rains it is wet

Similar Questions

• Satellite Pro L20-someone ' one can tell me if I have a problem with the screen?

  Hello

  I have a Pro L20 - PSL25E and I recently had problems with the screen, it was intermittently flickering/lose color and whiting almost (when the color fades white vertical lines begin to appear).
  This seemed to worsen after that I dropped it (only from about 2 feet off the ground, not a big drop).

  I thought that the sceen can go, but the performance of the laptop seems to be affected when this happens, the laptop started to run very slow (tracks mouse slowly, programs I clicked take ages to run and it freezes sometimes to stop flashing) that had me thinking that it might be a virus or performance problem.

  My screen, drivers are updated, I did a full scan with McAfee, ran a clear-up system and a Defrag.

  I was wondering if anyone knew if it seemed to be a problem with the connections of the screen and would need replacement or if it could be repaired or if it were a performance problem?

  Any help would be great thank you appreciate!
  Rebecca.

  Looks like the graphics chip has a problem, which I think is a motherboard replacement.

  You can get a quote for repair to an authorized service provider. There is a list of ASP on the Toshiba site.

• Problem with the screen on IPAD curtain

  Hello

  I'm a bad psychic, and I have a problem with the screen curtain.

  A longitudinal of Voice Over, the screen curtain is automatically activate.

  Normally to turn it off, you must type three times with three fingers. Only on my IPAD when I type three times with three fingers is "saying that turns off or preach. Find it me impossible to disable the screen curtain when voiceover is active.

  The latest version of IOS 9.2.1 is installed.

  I reset the Ipad and nothing changes.

  Can someone help me?

  Thank you

  Is is possible that the zoom is also on your iPad? If this is the case, try to use a quadruple 3 finger tap to turn off screen curtain.

  If the zoom is not active, try:

  1. Possessing the sleep/wake and home button until the Apple logo appears or 15-20 seconds.
  2. If, you can't remove the curtain of the screen, I would advise you reset the settings of the iPad. Settings > general > reset > reset all settings. It will be his turn VoiceOver off, but then you can use iTunes to turn on VoiceOver. Voice-over should return without the curtain of the screen automatically active. IOS - Apple Support using accessibility features

  The of is it possible that zoom is also active your iPad? In this case, you must use a valve 3 quadruple finger pour disable the screen curtain.

  try if the zoom is not enabled:
  1. While holding the button market / sleep and home to ' to the Apple logo, or 15-20 seconds.
  2. If you still can't delete the screen curtain, I recommend to RESET the settings on the iPad. Settings > General > RESET > RESET all settings. This turns off VoiceOver, but you can then use iTunes to turn on VoiceOver. Back to turn voiceOver should without the curtain automatically active screen. Use IOS - Apple support accessibility features

  -AJ

• my iPhone 6s has problems with the GPS when I use some applications, it does not work well and give especially the bad road. Can someone help me?

  my iPhone 6s has problems with the GPS when I use some applications, it does not work well and give especially the bad road. Can someone help me?

  My iphone 6 has started having the same problem. Its literally the GPS. Saying that it does not find me at all. Ive seen say location for more than an hour in the suburbs of chicago. It started to happen to me after I downloaded the latest update for the iphone. I hope they react and let you know what is happening because I'm dying to know as well.

• Hey I have a problem with the library, when I try to enable the creative cloud desktop application it keeps saying "cannot restore the file: C/users/USER name as the location of the file is not available."

  

  This is a double post of a following:

  Hey I have a problem with the library, when I try to enable the creative cloud desktop application it keeps saying "cannot restore the file: C/users/USER name as the location of the file is not available."

• I'm having a problem with the screen resolution cannot be superior to 800 x 600 pixels

  All this began after I plug an i9 phone to my pc to load

  later, to this day, when I turned on my pc screen resolution would not stay how I put it

  He wants to just go to 800 x 600 pixels.

  I ran microsoft security scan it found and deleted a virus java exploit cve 2010-4452

  but still having trouble with the screen resolution

  If the problem occurred after you plugged into your phone. I suggest to perform a restore of the system automatically, put it on a date 2 days before you had the problem. If this isn't the case, you can check the video card driver:

  Start > run > devmgmt.msc
  Check your video card driver or see if there are any missing drivers
  If its lack, then update or install the driver of your video card.
  I hope this helps you! Good luck.

• ThinkPad X 230 Windows 7-64: problems with the screen after updates

  Hi all

  I have a problem with the Thinkpad X 230. After a recent update of Windows 7 (64-bit), the screen resolution is set to 800 x 600 and brightness to the minimum. FN + F8/F9 does not work. The brightness is uncontrolled. I had to restore the system before the update.

  How to solve the problem, do anyone know?

  Thank you!

  Isosik

  Hi Isosik,

  Welcome to Lenovo Community!

  According to the request, we understand that you are facing problem with the display resolution on your ThinkPad X 230.

  If you have updated the drivers from Windows update, sometimes this kind of problem occurs with windows generic drivers for cause of driver incompatibility, suggest always update drivers only via the ThinkVantage System Update utility. Update only the application of Microsoft Windows Update.

  You can also manually download the drivers from the Lenovo support site.

  Lenovo support site.

  I hope this helps.

  Best regards

  Agnes Kumar

• Laptop G60-549DX (with OS Windows7-problem with the microphone when using Skype)

  Just bought a laptop G-60-549DX. His mic is BAD. Voice of cuts to when using Skype. Help!

  I was able to solve the problem with the microphone on the G60-549DX when using Skype.  I spend up to 6-8 hours, talk with convenience stores of HP.  They were very friendly and helpful.  The same help a friend.  My friend downloaded updated bios and micro drivers.  HP technician asked me to turn off the laptop, then remove the battery, unplug the power cord. With battery removed and stop, I pressed the market / off power button for a good minute evacuate remaining power into the computer. When I restarted the laptop I micro worked. I did a little more fine-tuning of the installation of the microphone.  Now, it works well on Skype and sound recorder. I won't take this back within the 14 days return policy.  It's a good computer I can say.  The technicians were all very friendly and helpful.  They called me several times to check to see if it still works OK! They are HUGE!  They want to help with any other question, I have perhaps with the computer.  Thank you very much for the help. Everyone was SO helpful.

• Problem with the screen size of my application in the emulator for BlackBerry 10

  Hello, I have a problem with the emulator for BlackBerry 10 and is as follows:

  When I run my application in the emulator waving, sounds good and all content is complete, however, when I run the application in the emulator for BlackBerry 10 soft looks as if she had a zoom very large level of predefined way and only see a part of the application.

  With controller emulator, I have changed the level of 70% zoom, but still does not work.

  Here, I'm posting two photos:

  

  

  One future half-assed answer

  var dpr = 1; // To set the meta on a real device to get 1:1 pixels
  
  if(typeof window.devicePixelRatio != 'undefined') // Does device support devicePixelRatio?
      {
      dpr = window.devicePixelRatio;
      }
  
  if(dpr) // Set up the right meta
      {
      var meta = document.createElement("meta");    meta.setAttribute('name','viewport');
  
      meta.setAttribute('content','initial-scale='+ (1/window.devicePixelRatio) + ',user-scalable=no');
      document.getElementsByTagName('head')[0].appendChild(meta); // Inject meta
      }
  

  This works perfectly, but must be placed in thethe document FIRST and foremost

  Live JS is used to avoid problems of library management

  It won't work in Wellington but works perfectly on all devices I've tried

  As mentioned in the code above just packaging needs in the script tags and setting very high index.html HTML code as you can get - right after

• Problem with the Screen class

  Hello

  Please anyone suggest me that I had made an application for blackberry strom 9500 when I got extends the class of devices back button screen is disabled automatically. and when I extends the class screen it works correctly.

  I don't think that the class screen itself has the feature to close the screen when you press the ESC by default. If it isn't and you want to use it, you can pass the DEFAULT_CLOSE style to it.

  public class MyScreen extends Screen {     MyScreen(Manager m)     {          super(m, Screen.DEFAULT_CLOSE);      }
  
      protected void sublayout(int width, int height) {        // Add sublayout logic    }}
  

  Documentation: http://www.blackberry.com/developers/docs/5.0.0api/net/rim/device/api/ui/Screen.html#DEFAULT_CLOSE

  Is there a reason that you are using the Screen as opposed to screen or full screen class?

• IPhone update (but an old having problems with the screen Activate iPhone and Apple ID)

  I have an iPhone 5 that, by chance (Pocket escaped), is stuck on the screen of the iPhone 'Find your phone' Activate.  The iPhone does not accept my Apple ID.  He is looking for an address icloud.com.  I can't honestly remember a set up, and I tried a number of variations on the icloud.com address (using the 'index' system provides) and passwords with no luck.  Do not have any problems with my Apple ID - I can see my phone & details on my screen of the user, when I connect my account (via the office).  Subject to my cellular service provider, I tried to force a restore on the phone via iTunes, but after that he asked me a few questions of initial Setup, I'm just at the "Activate iPhone" screen

  To be honest, I was going to pick up a new phone this week anyway.  My concern is now that I don't want to not suddenly faced with the same problem.  This lock, I meet - is - this quite specific for the phone itself? If I get a 6 plus and use this Apple ID to activate it, I ask in trouble? I admit that I am a twit when it comes to activation codes, the Apple ID, SIM cards and others.

  It was my first smartphone (+ 3 years now) and the installer was made by my employer, so strange things could happen at the beginning.

  Thank you all for any help

  If the implementation was made by your employer, they can put in something different from your Apple ID to find my iPhone. It also seems that if something was damaged in the fall. Who can contribute to the problem.

  If, when you receive your new phone, you make sure you use your Apple ID to find my iPhone, you should have no problem.

• Dual booting - problem with the disk when trying to start windows

  original title: problems with dual boot.  Windows does not play well with others.

  Hello

  I have Windows Vista Home Premium 64-bit included with the computer.  I installed Fedorah and it works on my computer.  When I installed it, but I had my hard drive partion.  I left most of the hard drive (about 400 concerts) as it was, when I booted up Fedorah worked well and gave me the option to boot or windows.  When I started in the window, however, it wouldn't let me start my computer, it says I have a problem with my drive.  With XP, it gives me no problem, I didn't ignore the disk check, but with Vista for some reason it doesn't let me start.  It gives me a few options of restoration to the previous status confuses the computer he says I manually type in which windows in the command line.  I don't have my windows CD, the only other option that I have that seems to work when I click it is restoring to factory fault which I don't want to do because I don't want to lose all my files.  Please tell me what I need to do.

  http://Fedoraforum.org/

  Fedora forums at the link above.

  A refund Stsrtup of Vista Disk link.

  Download the 64-bit on the right.

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  See you soon.

  Mick Murphy - Microsoft partner

• Problem with the resolution when you connect to a projector

  I regularly used my laptop connected to a projector via a cable VGA for PowerPoint and video clips view in Windows Media Player.   It is automatically detected and adjusted for different sizes of screen of the laptop screen (1366 x 768) and projector (1024 x 768) and projected with success.   Recently I connected the laptop to a second monitor - also 1024 x 768 - instead, and even once, it fits perfectly.

  It suddenly stopped setting for the resolution of the projector; When I go to the resolution of the screen, the option to set the resolution of the second screen is grayed out.   No matter if I use extend or duplicate, he insists that the two screens are 1366 x 768.   This has happened with two projectors, all two used to work properly.   I also tried different VGA cables.  The end result is that the image of the projector is hurry to tray.

  I can connect fine to the second monitor via the VGA port and sometimes with different resolutions for both screens.   I can also connect to a TV via an HDMI cable.   I can't try a HDMI cable for the spotlight as it is ceiling mounted, and the other is old and is not an HDMI connection.

  I checked the drivers and they seem to be up to date.

  My laptop is a Dell Latitude running Windows 7.   The graphics card is an Intel HD Graphics 3000.   I tried many suggestions already given on these forums without success.   The real puzzle is that it was working fine and nothing I can draw has changed except that I connected on the other monitor.

  Hi Tony,.

  Thanks for the reply with the status of the issue. I'm sorry to know that the issue is still unresolved, your efforts to solve this problem are much appreciated.

  I suggest to follow the method below and check if that helps:

  Method 1: Perform a system restore.

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  System restore WARNING: when you use the system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  Method 2: Uninstall all hidden devices:

  Step 1: See the article below to activate the devices hidden in Device Manager.

  Look at a hidden devices

  http://msdn.Microsoft.com/en-us/library/Windows/hardware/ff553955 (v = vs. 85) .aspx

  Step 2: After you enable hidden devices, remove devices from Device Manager.

  1. press start.

  2. type device manager in the start search box.

  3. Select Device Manager in the search result.

  4 uninstall everything that are grey also uninstall the drivers to display completely.
  5 restart the computer and install the drivers to view the manufacturer's Web site.

  Hope this information helps, just reply to the State of the question to get help.

  Hi Rizwan

  Unfortunately, I do not have a restore point old enough until the problem occurred.   I have not found any that was relevant in hidden devices, but in normal Device Manager mode when I clicked on "monitor" it opened a "Generic PnP" entry even when there was no extra monitor or projector fixed.   When an additional monitor has been attached, there were two of these entries.   I disabled them both, and I found that I can now adjust the resolution of a second monitor to a different setting of the laptop screen.

  Thanks for your help.

  Tony

• problem with the screen savers

  OK, I have windows 7 Home premium. Now, when I download a screen saver. I end up getting an error message. And I want to know how I can solve this problem. Or if I can fix it. I'll post the error here. Thanks in advance.

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: nfsRainbowAbstraction.scr
  Application version: 4.0.0.0
  Application timestamp: 4b0041b4
  Fault Module name: Flash32_14_0_0_145.ocx
  Fault Module Version: 14.0.0.145
  Timestamp of Module error: 53aa18ec
  Exception code: c0000005
  Exception offset: 001fbb14
  OS version: 6.1.7601.2.1.0.768.3
  Locale ID: 1033
  Additional information 1: dcdb
  More information 2: dcdbdf2902fa28773ce6a482d2712212
  3 more information: 9da6
  Additional information 4: 9da622ac40664012d59c7c96b3c0c476

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  Flash screen saver function?  Could be some screensaver you downloaded was made for a version MUCH earlier third Adobe Flash Player and/or the operating system.

  When I tried to go to the web page where you can get this screen saver (nfsRainbowAbstraction.scr) - my eSet NOD32 antivirus and Malwarebytes warn me constantly bad things even. Heh

  In other words - if work of other screen savers (i.e. - those of integrated)-the issue is either with (in this case) the Adobe Flash Player this screensaver uses or the screen saver itself.  Communicate with those who have made the screen saver.

• Problems with the screen resolution, Cloud based software and Photoshop after the last round of updates Windows 8.1.

  Original title: screen resolution problems.

  Since the last series of Windows 8.1 update the resolution of my monitors has been changed for the worse. I use an AOC 2367 M (resolution 1920 x 1080) as my first monitor and a 42 inch Sony Bravia (resolution 1920 x 1080) as my 2nd monitor. The changes are more noticeable on the Sony Bravia and any adjustment I make to the resolution only make worse it.

  I also have problems with some software clouds as I load using citrix and when I try and navigate once opened software, I can't because the pointer selects a point about 50 mm on the side of the where he is hovering. In fact it is very difficult to open and close as anything and I resorted to the laptop to get concrete results.

  Photoshop now also comes up with a message when I open it up to inform me that the monitor profile seems to be defective.

  Any suggestions would be helpful as I thought initially an another upgrade must follow to correct the ills of windows 8, but appears not to have happened.

  Hi Joseph,.

  Thanks for the reply.

  Method 1:

  I suggest you to download and install all Windows updates available including optional updates. You can also install the latest device drivers for all devices including display drivers and monitor drivers on the manufacturer's Web site.

  http://eSupport.Sony.com/Perl/select-System.pl

  http://www.aocmonitorap.com/root/ANZ/download_driver.php

  Method 2:
  Adobe Photoshop CC version 14 is compatible with Windows 8.1. See Windows Compatibility Center for more information. To solve the problem with Photoshop CC, I suggest you try the procedure described in the article and see if it helps.

  Cloud applications help creative /CC crash immediately after launch
  http://helpx.Adobe.com/Photoshop/KB/CC-applications-crash-immediately-launch.html

  If the problem persists, I suggest you to contact the Support from Adobe.

  http://helpx.Adobe.com/contact.html

  To solve the problem from software hosted accounts, you may need to contact the Support to count.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.