ProBook 430 1: cannot update win8.0 to 8.1. Update bios to ver01.31 may not even go to the store to down load

Similar Questions

• Tecra A9 - 11i: update Bios problem and AHCI works not

  Hello

  I have trouble to update BIOS for a Toshiba Tecra laptop A9 - 11i, (with the last update of the official European website of toshiba); After running the bios (version 3.2.8) Launcher
  "I get the message" this computer is not supported "? The latest version of the bios installed is 1.5, date 05/07/2007

  also if I can add a few questions:
  the function keys tdlo can't seem to work;
  led for the "FN" key light turns on when the key so assume the FN key works, but there is no response when you press on the "FN" key and one of the number keys on the f - I installed the software of the control unit as have been advised but this has not resolved.

  I also have difficulty accessing the AHCi ' mode to work in Windows XP Pro SP3. I chipset intel 965 m + ICH8M, the Intel ICH8M serial ata storage controller-2828 present in the Device Manager - the matrix storage manager does not work so I copied the file iastor.sys from the folder Manager matrix in C:/Windows/Driver/system32 and changed the registry as read elsewhere on the forum but have had no joy.

  any advice would be greatly appreciated, thank you very much.

  > I am having trouble updating BIOS for a Toshiba Tecra A9 - portable 11i, (with the last update of the official European website of toshiba); After running the bios (version 3.2.8) Launcher
  "I get the message" this computer is not supported "? The latest version of the bios installed is 1.5, date 05/07/2007

  This error message appears if you want to update a BIOS that is not compatible with your model of laptop.
  Toshiba pilot European page provides the BIOS 2.10Win for this model of laptop.
  If you have used certainly bad BIOS.

  > There is no response when you press on the "FN" key and one of the number keys f
  Controls of common modules the FN keys.
  If the issue should be resolved install common Modules v 6.06.00, 4.30.15 utilities
  Notes; You need to press FN + 1, 2, 3 etc. DON T press FN + F1 etc.

  > I also have difficulty accessing the AHCi ' mode to work in Windows XP Pro SP3. I chipset intel 965 m + ICH8M, the Intel ICH8M serial ata storage controller-2828 present in the Device Manager - the matrix storage manager does not work so I copied the file iastor.sys from the folder Manager matrix in C:/Windows/Driver/system32 and changed the registry as read elsewhere on the forum but have had no joy.

  First be sure that the AHCI is enabled in the BIOS.
  In addition, the Intel Storage Manager controls the AHCI so you should integrate the AHCI driver to CD Win XP as described here:
  http://APS2.toshiba-tro.de/KB0/TSB85017Z0000R01.htm
  or here
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

• After the last Windows 7 Corel Draw update gives the error: your computer may not be connected to the internet

  After the last update of microsoft don't work plugin CorelDraw Whatthefont. Use corel capture. I can see only: your computer may not be connected to the internet or you may have a firewall installed that blocks access to the internet.

  We try on Windows 7 and Windows XP, the two are not working. In Corel forum have said, it's the beginning after the last microsoft update.

  Can solve you?

  Sorry for my English.

  Thanks, problem was in router (probably). During weekend router died, now we have new (same type) and it s working on two PCs.

• Cannot open the document. You may not have permission or the document can be opened already.

  Whenever I try to open a document on our Mac server I get this error message: "cannot open the document. You may not have permission or the document can be opened already. "After that, I click Ok and then am able to open it. What is interesting is that immediately after the first time I try to open the file and get the error message that I noticed a .idlk (file locking) gets created even if she could not open. After that, I open it. Then, once I close it, the lock file goes.

  Someone knows something about this problem? For this particular user permissions are read/write on the file and all documents.

  Yosemite 10.10.3

  InDesign CC 2014

  Well, the problem has been resolved. It ends up being ESET antivirus v.4.xx for

  company. After I disabled it temporarily everything worked normally. So created

  exclusions for the shared network resources that they are working for.

• ProBook 640 G2: [SOLVED] cannot update Bios Probook G2 640

  I want to update the Bios of a Probook G2 640, Win 7 Pro 64.

  On the HP site, there is a download for v01.02

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=8430732 & swItemId = ob_163103_1 & swEnvOid = 405...

  Downloaded the file SP74154, there ran, questioned restarted the laptop: the result I got after startup:

  "The system cannot find one of the binaries updated BIOS. Please make sure that the correct BIN file

  is located on the hard disk of the system or on a removable USB under the folder "Hewlett-Packard\BIOS\New.

  or under the folder "EFI\HP\BIOS\New". It can also be placed in the folder "Hewlett_Packard\BIOS\Previous".

  or under the folder "EFI\HP\BIOS\Previous".

  [OK]

  Even though I made records and put in .bin, executed files the file of SP74514 even once, I got the same message and the BIOS is not updated.

  Gladly would he because we have problems with the wifi does not work after that we disconnect it and bring it in a conference room.

  If anyone has a solution?

  THX!

  Ok

  Can manually create you a folder EFI\HP\BIOS\New

  on the flash drive, then paste it N87_0102.bin it

  For example E:\EFI\HP\BIOS\New\N87_0102.bin

  Then, restart, type F10 to update the BIOS and see if it will work?

  Alternatively, restart the computer, press F1 for information system to keep. Once it opens, please copy and paste all the information here, especially product number, info motherboars and ROM version or something similar - what is there...

  Forward to your response.

• ProBook 430 G2: Cannot dowload for Probook 430 G2 drivers

  Hello

  I try to download the drivers for my HP Probook 430 G2 in recent days, as two fingers on the trackpad scrolling does not work. However, Web sites with drivers are not available. For example, http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=6943803 does not work.

  Any help would be appreciated.

  Best, Marjolein

  marjoleinf

  I just tried this link to HP Web site and it works.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Satellite U300-11v: cannot update Bios - error code 5 - without administrator rights

  I have recently bought a laptop Satellite U300-11v and use Tempo of Toshiba alerts.

  He advised me to update Bios driver - I have downloaded on my desktop.
  When I try to run the program I get the following message - "cannot load the driver, C:\Users\Sue\Desktop\bios-2007 1023123728\PHLASHNT. SYS -"Please verify your account. If you have no privilege administrator please log in again.

  I checked and there is only one user on the laptop - Sue and I am also administrator.

  Please tell us what to do. Thank you very much

  Click with the right button of the mouse and choose Run as Administrator option. Can you please point out if this helps or not?

• Portege A600: cannot update bios 3.0

  My current bios version is 1.6, the latest is the 3.0
  When you try to update the bios, I receive an INSTALL2 APPCRASH. EXE
  exception code c000005

  I tried to start it in safe mode, but that deer does not help

  Thanks for help

  Hello

  The istall.exe should not breaks down and you should not update the BIOS in safe mode!
  Windows should be started and should work properly!

  This is a Toshiba FAQ How update BIOS:
  http://APS2.toshiba-tro.de/KB0/HTD9502M10000R01.htm

  Eventually the error code is related to corrupted windows OS or some tools from Toshiba is missing.
  Using Win XP the common Modules must be installed.
  You are using Vista or Win 7 VAP (value added packaged) must be installed.

• Satellite Pro L670 - 14 p - cannot update Bios - error message appears

  Hello

  I downloaded the latest update of the Bios for the computer laptop afforementioned, and it is not allowing me to update. It says that I need to make sure that: Bios is not later than 210 (mine is 1.80), AC is connected (it is), and that the battery is greater than 10% fee (mine is 100%).

  I have tried everything I can think (update running as administrator, reset the bios by default, removing all power from the laptop for half an hour etc.) and I still get this error message?

  Does anyone else have this problem?
  Its got that puzzled me.

  Thanks in advance for any help!

  See you soon,.
  Craig

  Hello

  Did you install VAP (value added package)?
  If so, uninstall and update this tool. Once again install it and restart the laptop.
  Then try to update the BIOS once more.

  Good luck

• Cannot update Bios for Satellite U400 - 134 Vista 64-bit

  When I try to update Bios 3.50 courses it is said that I couldn't have an administrator rights, but I run it under administarator.

  Who knows about this problem?

  Post edited by: Gerus

  Hello!

  Satellite U400 BIOS 2.0.17.64?
  As far as I know the latest version of the BIOS for Satellite U400-134, which belongs to the PSU40E series is the version 3.50.
  Check again on the Toshiba site: http://eu.computers.toshiba-europe.com

  If you download the zip file, you should extract all files before you start the update.

  Good bye

• Cannot update BIOS on Tecra A9 because of admin

  Hello

  I want to update BIOS my Tecra A9 of 1.70 to 2.10 (Windows XP SP 2).

  When I run the update (P0054v210.exe), I get the error message: "[Error] the start of the service was abandoned. User does not have administator privileges. "

  Event log entries are:
  Application:
  ErrorCode: 9
  Source: CHGBIOS
  Description: "CHGBIOS" (the full message are in German and this forum does not allow German error messages, because they 'contains profanity or inappropriate language')

  System:
  ErrorCode: 7000
  Source: Service Control Manager
  Description: "NCHGBIOS2SVC" not found. (The full message are in German and this forum does not allow German error messages, because they 'contains profanity or inappropriate language')

  I started the update as the local administrator, but it does not work.

  Can anyone help?

  Is your image of recovery Toshiba Tecra preinstalled wit or you have installed the OS on your own?

• Qosmio F10 - cannot update BIOS because of the illegal version?

  While half of me says its not broken, so don't fix it, I try to update my F10 BIOS to the latest version, by using the method of installation of Windows.
  The file I downloaded and extracted tells me it's an illegal version of BIOS for my machine, but it's the (only) the Toshiba site gives me.

  Any ideas?

  Can I ask what version of BIOS have you tried?
  On the page of the Toshiba driver, you might find the BIOS 1, 20 - WIN.
  I downloaded since the page pilot European Toshiba.

  Please note that your original Toshiba OS must be installed to update the BIOS.

  But a question; Why do you want to update?
  If your laptop works ok, you shouldn't t update the BIOS. It s simply not necessary!

• Update of Vista 32 bit does not work after replacing the hard drive

  A month ago the hard drive of my computer (ACER Aspire 6920) had to be replaced. The disk image hard precedent (which includes the c: with Windows Vista Home Premium 32 bit, SP 2 build 6002) has been mirrored to the new hard drive. Everything seemed to work fine until I noticed that I don't have more updates from Microsoft. I tried a manual update and got the message that the update service was not working and I have to restart the computer. However, the Task Manager showed that the update service has been executed. Of course, I rebooted the computer, but nothing has changed.

  I found a whole bunch of recommendations for this issue in this forum, but nothing seems to work:

  • The Microsoft FixIT tool indicates a problem with the update of components, and then said that the problem had been solved successfully. However, the problem is still there and rerun the FixIt tool Gets the same message on a problem (yet) found and fixed.
  • I also stopped the update service, delete all content in Windows/C:\Windows\SoftwareDistribution and restarted the service. without success.
  • I've temporarily disabled my security suite (Eset Smart Security 6) and tried the update. I also have fittings the folder C:\Windows\SoftwareDistribution to the scope of the antivirus, without success. On the old hard drive, I used a different security suite so I thought that maybe the ESET (that I installed everything recently) could be the cause of the problem, but that doesn't seem to be the case.
  • I also followed the instructions provided by Microsoft at http://support.microsoft.com/kb/971058, but again, no change at all. However, it should be noted that registering some DLLs that Microsoft listed does not work (message that the DLL is not found or some server entry point (my translation, I'm using the German UI and don't know English good term; sorry) could not be found.)

  Http://support.microsoft.com/kb/947821 , I found another tool that supposedly can solve some problems of updating; I downloaded the version for Vista 32-bit, but it cannot install it on my computer (error code = 0xc8000247 during installation).

  So I'm really lost now what else to do. I would appreciate any suggestions. Please note that I am not technically very warned :)

  ARG, apologies.

  Was not aware that they had dropped support for Vista... (I myself have 'graduated' Vista earlier)

  The fact that you have not already installed TSRI is exactly your problem.

  Recent hard drives using 'Sectors 4 K', also known as 'Advanced Format Technology'.

  If the installed hard disk driver currently is not compatible with this specification,

  It will result in oddities like the status of the service Windows Update is not recognized correctly.

  Installation TSRI will fix this in most cases.

  Alternatively, if you are using Vista SP1 or later version (or 7 SP1), you can use the real driver.

  Since you are already updated to SP2, we will see if it is a viable solution.

  Go to: start-> Control Panel-> programs-> programs and features

  In the list of installed programs, locate and remove if found.

  -Intel Matrix Storage Manager

  -Intel Turbo Memory

  This should force your computer to go back to the real driver provided by Vista.

• ProBook 430 G3: cannot find the sata setting in bios

  Hi, I bought a G3 Probook with FreeDos preinstalled

  The config includes i5-6200U and 128 GB SSD

  I am trying to install Win 7 64 bit and when it starts on the USB drive and I select language and click on install it keeps listening on CD/DVD not detected and suggests to load the driver - it seems that it can't detect the internal SSD flash drive

  I looked in the forums and recommended to find the setting of SATA - IDE/AHCI, but I could not locate in the BIOS... the version of bios is 01.03

  Any ideas how I can do Windows Installer detects my internal SSD?

  Thanks in advance!

  UPDATE: I tried to use diskpart during installation and he did not see the SSD drive, so I guess that the DIF is with smth else... Please help, I am completely stressed because it's totally new laptop

  FOUND THE SOLUTION

  It seems that the problem was with USB 3.0 - for some reason drivers any, that none of the 3 ports did not run as 2.0 (())

  So I downloaded the driver and copied package on the SSD, and when prompet during the installation he merely indicated to the place with the drivers - worked well. Hope this helps someone as well

• Mini L9W - B satellite - cannot update BIOS running Windows 10

  Click Mini L9W - B with Windows 10.
  Everything works fine, but I can't update the BIOS to 5.20, via the Service Station or for download on the Toshiba site.
  Process gets as up to now by clicking on Yes to UAC... then nothing.
  Any suggestion is appreciated.

  Thank you.

  I have the same problem, also with Win 10.

  Meanwhile, the keyboard no longer answers.