Profiles of power does not

Similar Questions

• After the upgrade from my bookmarks list shows the entries less than before; the indications you have search a Profiles folder that does not exist.

  After Update Firefox on all November 9, I lost the list of bookmarks that I had before and it could access it from my homepage. Now it does not appear there. When I followed the instructions on your mozillazine.org help page, it says to find a profile file that does not exist with this version.

  One possible cause is a problem with the places.sqlite file that stores the bookmarks and history.

  • http://KB.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
  • https://support.Mozilla.com/kb/bookmarks+not+saved#w_places-database-file
  • http://KB.mozillazine.org/Lost_bookmarks

• H8 - 1360t: restarts power - does not work with the installed memory

  HP clubhouse, i7, Windows 7, 3 x 4 GB, discreet grahics

  The computer turns on, then immediately restarts.

  No beeps.   Monitor says 'no signal '.

  I tried

  -different (new) hard drive - no change

  -current hard disk drive shows no errors; all the data is there

  -installed the new power supply - no change

  -removed the discrete video card; used another card discrete video - no change

  -cannot test on-board DVI video because it does not have the 4 holes next to the long bar. all my vga DVI connectors have the long bar with the four holes around it (sorry I don't know the different DVI connectors)

  What works:

  When I remove the memory, it will beep seeing that no memory is installed; AND the computer continues to operate (it is not restart).

  -J' tried memory (3 of them every 4 GB) as single and pairs between 2 blue 2 black slots grids.   No change

  -J' tried another key to 2 GB - no change

  Suggestions?

  Thank you

  Darryl

  Problem was the motherboard.   Replaced by the exact type as to doesn't interfere is not with the software installed.

  Everything plugged immediately when starting on the new motherboard.   The user has a problem with software that had to be put back.

  So-

  1. If the computer won't power more than 5 seconds

  2. change the components with known good components does not change the restart without end to power on

  It is the motherboard.

  Thanks for the help.

  Darryl

• Acer Aspire s7 392 - power does not

  After installation win 10 my Acer Aspire S7-392 sometimes will not turn off. Especially if my Acer has sat for awhile. Also when I have the office close and then open the lid, the computer does not (black screen). I have to turn off manually by pressing power. Have someone ' an at - it the same problem on their Acer Aspire S7-392? Please respond if you have a solution...

  I FINALLY found the solution to the problem of the power-off/sleep;

  Go to the Control Panel

  Click devices

  Under System devices to find... Intel Management Engine Interface

  click it, and then right-click to find real estate

  DRiver , it will tell you what version you have.

  Mine was worm. 11 - who is the culprit.

  I chose to roll back the driver to 9.5.xx

  Once I did this back roller... I have more the shutdown problem.

  Hope that works for you.

• mode low power does not work

  After you have reinstalled Windows XP on my desktop data certified, low-power option does not appear in the Power Options in the control panel or the display option "pending" in the case of Windows XP is faded and does not work. Is there a solution for this. I have re-installed, and he always does. Could this be something to do with the battery?

  Solve you this problem?

  If you don't it has not set, you must provide the rest of the information - especially this part:

  Click Start, run and enter in the box:

  Msinfo32

  Click OK, and when the system info summary appears, click Edit, select all, copy and paste then return here.

  For information about video drivers, expand components, click view, click on edit, select all, copy and then paste the information here.

  There will be some personal information (such as the user name and the name of the system), and anything that turns information private for you, simply delete it.

• Profile of user does not write in c:\windows\temp

  Due to an update of Firefox, I damaged my user files.  I installed a new profile, the limited access, to surf. Now when I try to download programs or to run JAVA applications, I get an error message... "cannot write to c:\windows\temp, access denied, file is read-only. Change the properties of files or contact Admin"in some way, I lost the ability to write to this folder. Changing the property of the 'read only' file does not work, it activates again when the file is closed. I have here a way to solve this problem while still limiting the administrator user profile. level?

  First of all, if you look at the 'Read only' attribute of a folder in the Properties window, you must know that this box has absolutely nothing to do with any read-only attribute.  It is actually used to customize the folder.  Microsoft's explanation of this is in the following article:

  "You can not view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7"
    <>http://support.Microsoft.com/kb/326549 >

  To change the access permissions to a specific folder, the easiest method is to log on as an administrator and change the permissions using the 'Security' tab, as seen when right click on a folder and select "Properties".  If you do not see a 'Security' tab, this means that you have XP Home or you have XP Pro with 'Simple file sharing' enabled.  Assuming you have XP Pro, you can change the access permissions to the terms of this article:

  "How to disable the file sharing simple and how to set permissions on a shared folder in Windows XP"
    <>http://support.Microsoft.com/kb/307874 >

  If you have XP Home Edition, you can start mode safe (repeatedly tap the F8 key during startup key) and then log in as an administrator and follow the above article, or you can log in as an administrator in Normal mode and use the command "cacls" from a command prompt window.  To bring up a command prompt window,
  Start-> Run-> "cmd".
  Then, enter the command:
  cacls C:\Windows\Temp/e/g everyone: F
  What will give "everyone" access to the complete directory.

  HTH,
  JW

• Pow() does not correctly handle the fractional exponent

  The pow() function does not seem to properly handle fractional exhibitors.  The correct value is returned by the function pow() to the following code:

  hole_position [B5_B].neutronCount.presentCount = pow ((hole_position [10].detectorCurrent * hole_position [12].detectorCurrent * hole_position[13].detectorCurrent), 0.333);

  For values of current 1.1e - 7, 1.3e - 7 and 1.4E - 7, a value of 1.28E - 7 is returned.

  I had originally used the following code:

  hole_position [B5_B].neutronCount.presentCount =
  Pow ((hole_position [10].detectorCurrent *.detectorCurrent hole_position [12]))
  ((* hole_position [13] .detectorCurrent), 1/3);

  In this case, pow() returned a value of 1 for current values.

  0.333 using gives the precision necessary for my application, but the behavior during the passage of a fractional exponent seems to be a minor bug in this library function.

  This isn't a problem with pow, but rather a hunt for witches of the C language. In your code, 1 and 3 are treated as integers, and the division of two integers is an integer result. 1/3 becomes the integer 0. That's why pow returns 1.

  The solution is to do something to this effect:

  ((double)-1) / 3

  or better,.

  1.0 / 3.0

  As long as you make sure that one of the operands is double, the result will be too.

  A. Mert

  National Instruments

• WRT120N - power does not

  Its the W120N I think. It turned off by itself so I can't make it work now. The lights does not come on when I Plug and when I tried to connect it to any other power outlets, lights flickered, then off again.

  I hope that this router has not yet been bricked. Try to reset the 30-30-30. Connect the computer to the router and check if this computer can still get a valid ip address. You should also make sure that the router is using the correct power adapter.

• Profile of user does not periodically; Windows Update does not work

  I had the "the user profile Service has no logon. Failed to load the user profile"and did a system restored about two months ago. I had the same error once again and followed the instructions that I got from a help forum to identify my user profile when the computer starts. Then I got the error again and did a system restored again. Two things have happened:

  1. about every fourth time that I reboot, it loads to a temporary profile.

  2. Windows Update does not work. The error that appears when I try to run Windows Update is 80070005 "unknown error."

  Help! What's next?

  Corruption of the profiles can be caused by several things: malware infection, bad drivers, corruption of file system of Windows due to stops unsuitable, due to lack of material (RAM and disk hard first "suspects"). You need to know what caused the corruption.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  If you can't do the work yourself (and there is no shame in admitting this isn't your cup of tea), take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad). If possible, have all your data backed up before taking the machine into a shop.

  MS - MVP - Elephant Boy computers - don't panic!

• Cannot create a new user account, the user profile service service does not log and cannot install a program

  I can't create a new user account (Windows 7): the user profile service service has no logon.

  I have an administrative account which is the only account. I have problems with the installation of Autodesk Inventor so I need to create another user to see if I can solve the problem. But when I want to make a new user account and I get the following message: I can't create a new user account (Windows 7): the user profile service service has no logon.

  I haven't added new programs in a long time and I don't know when this question has been raised as I've had my laptop for 3 years and this is the first time I create another account than my original. I don't want to reset my computer manufactured settings.

  I also followed the http://support2.microsoft.com/kb/947215/en-us but I can't find any registry master in the list of profiles. In fact, I am the only user in there...

  It seems that my computer does not have a record in the system registry.

  In fact, the problem started when I tried to fix the "C:\windows\system32\config\systemprofile\desktop refers to a location that is unavailable. It could be on a hard drive on this computer.or on a network. Check to make sure that the disc is inserted correctly, or that you are connected to the Internet or your network, and then try again. If he can't always find the information could have been moved to another location. "I was at least able to connect in the new user but will load a default profile and therefore do not load the profile properly. It seems I've done worse the problem after doing

  gpupdate/force

  at the prompt as an administrator.

  The very initial problem started all this was when I was running from Autodesk Inventor, it gives me the following error: Mismatched Ole32.dll and Comcat.dll. And the support2.microsoft.com/kb/201364/en-us is to say that since I am under Win7, the solution is not applied. So I'm stuck. And the next move was trying to see if a new user profile may solve the problem.

  Any suggestions will be greatly appreciated.

  And if possible, please also suggest a "repair" method so I can get Win7 function correctly without reinstalling the whole machine. "" I use a laptop so I do not have installation media.

  Thank you.

  Hello

  Thank you for your update on the issue.

  I suggest that you try to run the file system (CFS) Checker scan to check all the corruption of .dll files.

  1. Go to Start, click all programs and open the Accessories.
  2. Right-click on command prompt in the list programs, and then select run as administrator. If you are prompted for an administrator password or for confirmation, type your password, or click OK.
  3. In the command prompt, type the following command and press ENTER:
     sfc/scannow

  For more information, see this link:

  http://support.Microsoft.com/kb/929833/en-us

  Please post back your results for assistance.

• Profile of user does not and much much more

  Ok... I read the user profile does not load help, but I can't get the solutions to not work. I hope someone here can help me.  :)

  I have created two profiles.  One is the admin (mine) and a second one for my wife.
  I get the error message "Unable to load profile" (or something of the sort) when I try to open my user profile (admin one)
  Following a thread on this topic, I tried to create an additional profile.  However, when I click on 'manage another account' my computer does nothing.  This is true in safe mode or using my spare user profile.  When it asks for a password here or any other time in my tests, when I type in correctly, it does nothing.  If, as a test", I type in the wrong, I get an error message, so I don't know, I type the wrong password.
  Now, I can access most of the files under my user name.  The exception is "documents" and "desktop".  Fortunately, I can get 'MY documents' so I put everything on an external drive.  (and I can do at the moment as well under this profile.)
  To complicate the ways, if I try to run cmd WITHOUT running it as an administrator, it is well, but I can't scan my drive as I want to.  When I right click Run as administrator, I get the message "Windows cannot find"C:\Windows\System32\cmd.exe".  Make sure you typed the name correctly and then try again. »
  I start back up once a week, however, I can't run "System Restore" restore all my files.  I get the error with both messages.
  After working with it for a while, I can't get into safe mode.  After hitting F8, I reach a frozen screen.  In other words, I can not navigate to other settings, and I can not select the default value.  (I think it's "repair menu" or something of the sort.)
  I found a thread to force the computer into safe mode to start upward.  However, when I go to run msconfig, I get the message "Windows cannot find 'C:\Windows\system32\msconfig.exe'.  Make sure you typed the name correctly and then try again.
  I am running windows 7 Home premium (service pack 1) 64-bit.
  My processor is an AMD phenomenon II X 6 1090 t. processor 3.2 GHz.
  8 GB of DDR3 RAM.
  It's a HPE-470f.
  I have scanner antivirus (AVG) every night and often run spybot and malware bytes to check other unpleasant things.
  ANY help that anyone can provide is much appreciated.

  I feel that your machine has suffered serious damage. What it is that I have no idea. I could do this:

  1. Set your BIOS so that it uses the DVD drive as its primary boot device.
  2. Start the computer with your Windows 7 repair CD.
  3. Press a key when prompted to boot from the DVD.
  4. Select 'PC Repair' in the menu.
  5. Select 'Repair' when prompted.
  6. When you are prompted, select System Restore.
  7. Configure Windows in two weeks.

• HyperV 2012 SMV "off the power" does not appear in the converter 6.1.1

  Hello

  Environment:

  HyperV 2012

  VMware Converter 6.1.1

  VMware 5.5

  I want to convert all Hyper-V in VMware virtual machines

  A virtual machine worked without any problems! Power off of the virtual machine and do normal "conversion process" - all right, but all the other VMS does not appear in the converter as soon as they are "off".

  I start VMware Converter

  -Convert the Machine

  -Source HyperV - Server (Powered off)

  that shows me all the virtual machines on the Hyper-V environment. As soon as I turned off one of the virtual machines that VM is endangered. I see not the virtual machine until I have restart the virtual machine.

  All ideas

  Thank you.

  Hello

  so, finally I had to delete all virtual machines to Cluster Hyper-V role, restart the converter on the Hyper-v host Agent, and then everything went well.

  Thanks for your help!

• DNG Profile Editor done does not work with profiles of the V4

  I noticed that the DNG Profile Editor does not work with the new v4 for the D700 profiles.  The DNG profile editor will be updated to work with the new profiles?

  Yes. It is not yet ready.

• Dell Inspiron 531 s problem of power/does not recognize the hard drive

  My Office does not illuminate. I replaced the power supply. No, it powers on but does not recognize the hard drive. It gives an error as SATA 0 None SATA 1 no SATA 2 No. How do we know that the cables are properly connected. I feel like I'm very close to solving the problem but don't have a clue what that next step to follow

  The original PSU had 4 sets of cables and connectors.  The new power supply has 5 sets of son.

  aries7531

  From your post, I guess that the configuration of the system now recognizes the hard drive?

  If you do not have a floppy drive, then BIOS can find the player who isn't there, it returns this error.

  Make sure that the floppy drive [drive A] is disabled in the [BIOS] installation system, page 173, so that it is no longer looking for the disc and see if this stops the error message.

  If the hard drive is recognized in the configuration of the system, he now knows in windows "My computer" or in "disk management, [right click on 'My computer' and select 'Manage', then disk management]."

  Bev.

• Satellite P100-347 - AC power does not

  I thought I'd let everyone know a solution to a problem.

  I used the laptop for long hours and I found it out the next immediately at startup.
  The power supply was not working and prevented from leaving.

  What I did for the solution...

  1. no AC power on, remove the battery.
  2. wait 30 minutes
  3. connect the power cable. (AC power indicator should now light)
  4. start the PC. (it starts!)
  5. turn off the PC.
  6. reconnect the battery.
  7 reconnect the power cable. (AC power indicator should now light)
  8. wait battery light to show his load again. (light blue instead of orange)
  8. start the PC. (it should work now!)

  I really hope that someone benefits from this because I felt with the laptop went I had lost a member.
  I am now happy. I still have that gives more time. But I'm a happy Bunny at OM.

  Price for the repair looked nasty and we talk on the motherboards web gone. Yuukie.

  Looks full of supply circuits switches do not properly with battery and AC. As he would not spend
  Using the battery to use AC the AC was plugged after starting on batteries.

  Carlin

  Yes, that sounds like a motherboard problem. I would like to send the laptop to an ASP for a quote. It could be something as simple as a bad connection.