Protection of E-series back?

Similar Questions

• N - Series - loop protection

  Hello

  How exactly loop protection on N-series books?

  I test the behavior on N2048P and it looks like the following:

  When I connect two ports (botch are configured in the access mode in the same VLAN) via a cable, after a while the two ports are disabled and the following messages are written in the newspapers:

  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33665 per cent on item in gi1/0/13 link is down
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33664 %% Link Down: item in gi1/0/13
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33663 %% link on article gi1/0/14 is down
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33662 %% Link Down: item in gi1/0/14
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33659 %% link on Vl1 can't
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33658 %% Link Down: Vl1
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [loopProtectTask]: traputil.c (763) 33657% loop detected on port:
  <189>18 Jul 18:48:04 10.10.0.1 - 1 TRAPMGR [loopProtectTask]: traputil.c (763) 33656% loop detected on port:
  <189>18 Jul 18:47:39 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33649 %% Link Up: item in gi1/0/13
  <189>18 Jul 18:47:39 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33648 %% Link Up: Vl1
  <189>18 Jul 18:47:39 10.10.0.1 - 1 TRAPMGR [trapTask]: traputil.c (721) 33647 %% Link Up: item in gi1/0/14

  I couldn't find all the details on this mechanism in the N-series documentation.

  I'm curious to know if it is possible to customize to meet the threshold of better times etc. - depends on the situation.

  Kind regards

  Jakub

  Looking into this a little further, looks like there is a command added in 6.3.0.1 and newer firmware.

  # errdisable recovery cause

  and

  the errdisable recovery interval #.

  These commands should enable you to change the behavior of loop protection. Take a look at page 491 of the CLI guide and let me know what you think.

  http://Dell.to/1SVu3Bp

• Allergy Apple Watch sport - protective film

  My wife Gets a skin irritation while wearing the Apple Watch Sport.

  So I'm looking for a protective sheet to the back of the Apple Watch.

  I have haven´t found such a tool.

  Can anyone give me a tip?

  Hello

  You can find this product, for example, interest:

  • http://www.skinomi.com/sk18691-Apple-watch-38mm-skin-protector.html

  Also consider guidance from Apple about the skin irritation and the potential for allergic reactions:

  • Port Apple Watch - Apple Support
  • See under the sensitivities of the skin: https://help.apple.com/watch/#/apdcf2ff54e9

• Re: Unable to install HDD Protection for Satellite L750-A218

  Hello

  When I try to install the Toshiba HDD Protection software it says that its not available for the model.
  I got the exe of the drivers Web page for my exact model of latoptop.

  It is a follow-up of:

  http://forums.Toshiba.com/T5/drivers-and-utilities/HDD-protection-not-available-for-this-model/m-p/298900/

  Thank you.

  Hello

  You are looking for HDD protection Utility for Win 7 64 bit system.
  Right?

  The utility of the HARD disk protection was preinstalled on Win 7 32 bit system?

  I found the 64 bit HDD protection utility for series Satellite L755 version.
  There are two different versions: v 2.2.1.12 and v2.2.0.12

  Try to install both, but before you do this, you must install the VAP (value added package) for 64 bit system

• Backup BlackBerry Smartphones get BB protect compared to the clouds

  Hello world

  I tried the manual backup yesterday by the site Web de Blackberry Protect. I successfully backed up the first time and made a few changes on my BB Curve 9300. Freed from some space by deleting messages and other data. I also want to return to the top of that State or to this specific point, I did the backup through the site Web of Protect. To my surprise (and I'm not aware) the new backup crushed my previous where in I need important messages I deleted expects that the backup will just create another set of backup rather than crush the other.

  My question is. Are there opportunities that I can restore this backup?

  After a few searches on Google and read messages. I knew that the backup is saved in the cloud that has lost the chances of recovering data backup with recovery tools that I can use.  I thought that if I can retrieve/recover deleted files and even formatted disks, technical staff of BB Protect or RIM could do the same and help me with my problem.

  Hope my message reached the Cloud for RIM or BB Protect administrator.

  Thanks in advance.

  Anthony

  Hello and welcome to the community!

  First of all... this site is not a channel for any official communication with, support, or climbing to the RIM. This site is a community of users for volunteers who are trying their best to help each other, but we have no access to any system "back-end" to act on your request. If you really need official support from RIM, you must start with your support contract required string that starts with your mobile service provider, which can degenerate case RIM free of charge to the end user if such is always appropriate.

  There is something called incident support, but it costs to just ask the original question, since you are not through the contract, you signed at the time of purchase. If you want to study, you can check it out here:

  • http://us.BlackBerry.com/support/programs/technical/incident.html

  OK... with that of the road, see:

  • KB25063 How to use BlackBerry Protect to restore data on a BlackBerry smartphone

  According to who, it should actually be different dates you can use BB Protect backups. If they are not, however, appear for one reason or another, they are not available to you through any means automatic... and you would need official support (above) of a human being to the RIM to see if it can be recovered.

  All this said, I hope that you are not solely on BB Protect for your backup needs. BB Protect only back up (I think) 8 databases, which is a small subset of all the content of all of your valuable data. FYI, here's the process that I always recommend:

  Daily - configure BB Protect to save what he can, preferring to WiFi if the network of consumer data carrier is a matter of concern.

  Weekly:

  If you're not up to BBM7, then manually save your BBM contacts to the memory of your device or Media Card

  • KB20554 How to back up and restore the BlackBerry Messenger contacts list

  Via the mass storage Mode, copy all the contents of the memory of your device and Media Card on your computer

  • KB11879 What is the mass storage mode

  Via the desktop software, perform a full backup of your BB

  • KB12487 How to back up data from smartphone BlackBerry using BlackBerry Desktop Software for Windows
  • KB03974 List of database for the blackBerry smartphone

  There is an old saying:

  • There are two types of computers of users of devices - those who have lost data and those who will be

  As insurance, the backups are reactive or an optional activity. And this process, in my humble OPINION, provides the best protection of all the valuable data that is kept on their BB. When you compare BB Protect backup actually compared this process to protect, I think you will find that the difference is very large. In addition, this process would give you 100% control to keep the previous backups.

  Good luck!

• screen protectors

  recommend apple or watching a screen protects for the series?

  peter.....................

  Hello

  A good quality (of type thin film) screen protector can be effective to provide a degree of protection against any possible damage.

  Consider, for example:

  • http://www.ZAGG.com/us/en_US/invisibleSHIELD/Apple-watch-42mm-screen-protector/h high-definition-apple-watch - 42mm
  • https://www.ARMORSUIT.com/pages/Apple-watch

  Apple advises that protective no screen must be mounted. It is a matter of personal preference.

• Change to bing as default search engine

  I think that I fixed it by running malawarebytes. AVG has been remove search protect but it came back. has run malawarebytes and it seems to have disappeared.

  To change the default search engine or the order of the search engines in the upper search box right in Firefox, please do the following:

  1. Move the mouse cursor inside the search box in top right of the Firefox window and click on the arrow next to the logo of the supplier.
  2. If you want to select another search engine, simply choose the engine in the drop-down list.

  To change the order of search engines, follow these steps:

  1. In the drop-down list, select Manage search engines....
  2. In the next window, you have all your search engines listed. To change the order, simply click on a search engine, and then select move up or move down from the buttons on the right side to change the order of search engines.

• Satellite P10-304: bad sectors on the disk - how to fix?

  My drive HARD drive bad sectors developed and replacement needs, does anyone know how to do this?

  My model is a P10-304.

  In addition, Windows will not start upward in my old HDD because of bad sectors and the drive is protected by Norton and back, does anyone know how to bypass or disable round trip

  Hello

  I found these tips how to disable the Norto Go Back tool.
  You can uninstall it from your computer, disable GoBack to your laptop press 'space' GoBack screen button and select the option "disable" GoBack.

  Follow these steps:
  1. reboot your computer.
  2. when the Norton GoBack splash screen appears, press the SPACEBAR.
  3. in the Norton GoBack boot menu, click on disable.
  A message informs you that disable Norton GoBack erases history and you will not be able to run the hard drive or hard disk restore advanced restore until Norton GoBack is turned back on.
  4. click on Yes.
  5. click on continue.
  Your computer restarts automatically, and Norton GoBack is off
  After restarting the laptop, I recommend once again using the following key: CTRL + ALT + G.
  Immediately press on and hold the keys Ctrl + Alt + G after restarting the laptop you. A message you giving the possibility to force the removal of GoBack master boot record. Press F to force the removal of GoBack master boot record.

  If failure of keys Ctrl + Alt + G in the first time then try this again for three or four times until you get the prompt to remove the master boot record of GoBack.
  Finally, restart the computer.

  To fix bad sectors on the HARD drive, you could boot from the XP CD to use the console of "repair".
  And then use the CHKDSK /p command to repair the bad sectors.

  Good luck

• Satellite L850D - 12 p - the rider on the own BIOS password

  Hi all.

  I was given a laptop by a parent and I would use it but for the moment can not.

  To be honest, the reason that this has been given to me was that there is a password that they have forgotten and even mentioned that the laptop is mine, but I have to have the password removed the bios boot somehow.

  I've seen many mentions of the B500 rider in Google but I can not find these on this laptop. No, unless they are hidden pretty well.

  There are at least under the removable cover only, memory, CMOS battery and HARD drive.

  I had the battery, HDD, RAM and portable removed and left alone for a week. This resulted in nothing.

  Is - this laptop has a clear CMOS jumper at all? Anyone know what is her name?

  Laptop model is by Satellite L850D - 12 p.

  Thank you very much.

  Albert

  Hi Albert

  Please don't get me wrong, but we cannot start such things on the public forum of Toshiba.
  BIOS password is very important security feature. As far as I know Toshiba uses several techniques for BIOS password removal. One that is used on your computer does not for me so I can't help you with this.

  Point is that many users protect machines clean and backed up data with this password. When we are discussing here on this subject and maybe offer detailed how do to remove the BIOS password each laptop stolen could be unlocked.

  BIOS password removal just contact the nearest Toshiba service provider and ask for help.

• How to upgrade all the updates of Windows XP from a single package?

  Original title: Windows XP updates

  Is there an SP4 or a package that contains all of the updates of Windows XP after SP3 is released?  It would be extremely useful to update all of the XP machines that do not have access to the internet.

  There will be a version called SP4 update by private parties. This update has been treated since September of 2012. Currently, they are still working on it. You can access this information to

  http://www.RyanVM.NET/forum/viewforum.php?f=5&SID=3058537efee42c994a4945a016f82cc3

  Hope this helps, they recommend you to read the info from the beginning. With files and information, you can create an ISO file that can be used to create a version of XP from microsoft that you can use in the future. I do not recommend to use a good firewall and antivirus program to protect your system like back up your system regularly.

  Personally, I'm going to build me a new computer.

• How can I fully remove Win32/PossibleFileHostsHijack?

  I made a quick security scan and discovered I had the above.  Security sweep removed partially, whatever that means; I want her to be completely removed. Any help will be appreciated.

  Security sweep removed partially, whatever that means;

  Basically, what this means is that your host file was not replace/repair by the scanner. So probably your search or other navigation attempts will be re-directed to unwanted sites eventually leading to infections by malicious software.

  Click HERE and run the file. It's the automated Microsoft FixIt. It will restore the default settings of your host file.

  Click HERE to download, install, update and perform a full scan with Malwarebytes. It is recommended that purchase you the version of Malwarebytes Pro if possible. Otherwise, you can still use the free version, but will not the benefits of the Pro real-time protection.

  Post back with the results of the Malwarebytes scan. It may be necessary to perform additional analyses with other products.

• Access denied message to scan and a program after running disk check

  Original title: chkdisk found bad sectors on my hard drive and seemed to move them, but now I have deinied for my scanner and a program so far. How can I fix it

  I cnt day Quicken or use my scanner. I get "access denied".

  Hi rosiemate,

  To check if the following is useful.

  Method 1:

  Step 1: Disable Zone Alarm temporarily and see if you still have access denied message. If there is no error, you may need to look in the settings of the program.

  Note:  Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

  Step 2: As you can see the files unusable for Quicken, you can follow this article to check the issue.

  Alternatively, you can consult this article.

  It may also be a possibility of a corrupted user account.

  Method 2:

  Step 1: Create a new user profile to test the issue. See the "create a new user profile on the computer working group" section of this article.

  Step 2: If the problem does not occur, follow the "copy files to the new user profile" in this article.

  I hope this helps.

• Why no games start after successful installation?

  I have recently completely reformat my hard drive and reinstall XP SP3 - since then no games will start for example. Crysis2, Borderlands, Far Cry, etc. Most of them just install apparently successfully, but when I run get them the hourgalss for 10 seconds and then nothing. The only exception is Borderlands that comes up with the following error message:

  C:\Program Files\2K Games\Gearbox Software\Borderlands\Binaries\Borderlands.exe

  This application has failed to start because the application configuration is incorrect. Reinstalling the application may fix this problem.

  >>

  All of these games used to run fine, my material has not changed, and since reinstalling XP SP3, I have downloaded and installed the latest NVIDIA drivers Creative etc.

  Most graciously accepted ideas

  Fraser

  Hi fraserwood,.

  ·         You have an installed antivirus program?

  Method 1: Temporarily disable the antivirus on the computer program and check if it helps. If it works, you may need to check the settings of the program.

  Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

  Method 2: Make sure you have the latest updates of Windows installed. To update the most recent and then try to install the games.

  Windows Update

• Win t Home Basic: windows cannot access \\NameXP

  Connection ethernet desktop, Windows 7 Home Basic:
  Windows cannot access \\NameXP, Err code 0 x 80070035

  Computer NetBook, Windows XP Home Edition, Wireless connection:
  \\NameWin7 is not accessible. You are not allowed to use this network resource

  Working group name is the same on both computers. Both computers are connected to the wireless router and have Internet access, but cannot see each other. Sharing is turned on, and there are shared folders on both computers.

  The problem is on the Netbook computer - I can configure the third computer (Windows XP Professional laptop) to access desktop computers via the wireless.

  Hi VojislavJosimovic,

  ·         Which antivirus program is installed on the computer?

  Method 1: Temporarily disable the antivirus on the computer program and check if it helps. If it works, you may need to check the settings of the program.

  Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

  Method 2: You can follow this step by step guide and check if it helps.

  Networking of computers running different versions of Windows

  See also:

  Sharing files and printers with different versions of Windows

  Error message when you try to access a network Windows XP computer: "you might not have permission to use this network resource".

• do I need to fix "broken digital signature" dethrone "name of the object; "' C:\WINDOWS\system32\vsflex7L.ocx '? Thank you, P.

  AVG2011 scan found this issue. I have a lot of trouble opening any window.

  Hi Patti_963,

  Microsoft safety scanner should not interfere or conflict with other antivirus programs. However, you can temporarily disable AVG and use the scanner.

  Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.