public static problem (inside, outside)

Similar Questions

• static routes - PIX outside address

  I tried to get a configuration (PIX501) which allows inside customers access to the outside and also allowing outside access to a smtp mail server in-house. From what I tried, it seems that I can't use the external IP address of the pix for the static control (indoor, outdoor). If I do other client access to the outside world is denied.

  So far I couldn't find any documentation about it. Can someone point me in the right direction plse?

  Hi morris,.

  I Don t know what the other guys are talkin´about, but it seems to me that they do not exactly understand your question and provide you with wrong information.

  In my opinion you want to translate all your inside source of addresses to the address of interface outside. It is already well configured, I saw in your config file. Indeed, these two commands are correct:

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  What bothers you is you want your mail server to be accessible from the outside to the inside for SMTP. The command you tried is:

  public static interface (inside, outside) MyServer netmask 255.255.255.255

  And it does not work.

  The command you need is the following:

  public static 25 25 MyServer netmask 255.255.255.255 interface tcp (indoor, outdoor)

  This static creates the translation for tcp port 25 (smtp) outside address to port 25 of your inside the server interface.

  I advice lets you modify the line "access-list permits outside_access_in tcp any any eq smtp" in "outside_access_in of the list of permitted access tcp any host 209.164.3.5 eq smtp".

  Put all together, modifications, you must perform:

  not static (inside, outside) interface MyServer netmask 255.255.255.255

  public static 25 25 MyServer netmask 255.255.255.255 interface tcp (indoor, outdoor)

  no access list outside_access_in not allowed tcp any any eq smtp

  outside_access_in list access permit tcp any host 209.164.3.5 eq smtp

  Finally make a clear xlate and it will work.

  Best regards and good luck,

  Leo

• Public static political static NAT in conflict with NAT VPN

  I have a situation where I need to create a VPN site-to site between an ASA 5505 using IOS 7.2 and a Sonicwall NSA4500. The problem arises where the LAN behind the Cisco ASA has the same subnet an existing VPN currently created on the Sonicwall. Since the Sonicwall cannot have two VPN both run on the same subnet, the solution is to use policy NAT on the SAA as well as for the Sonicwall, the new VPN seems to have a different subnet.

  The current subnet behind the ASA is 192.168.10.0/24 (The Sonicwall already has a private network virtual created for another customer with the same subnet). I try to translate it to 192.168.24.0/24. The peer LAN (behind the Sonicwall) is 10.159.0.0/24. The ASA relevant configuration is:

  interface Vlan1

  IP 192.168.10.1 255.255.255.0

  access extensive list ip 192.168.24.0 outside_1_cryptomap allow 255.255.255.0 10.159.0.0 255.255.255.0

  list of access VPN extended permit ip 192.168.10.0 255.255.255.0 10.159.0.0 255.255.255.0

  public static 192.168.24.0 (inside, outside) - list of VPN access

  card crypto outside_map 1 match address outside_1_cryptomap

  In addition, there are other static NAT instructions and their associated ACLs that allow certain traffic through the firewall on the server, for example:

  public static tcp (indoor, outdoor) interface smtp SERVER smtp netmask 255.255.255.255

  The problem is this: when I enter the static strategy statement NAT, I get the message ' WARNING: real-address conflict with existing static "and then it refers to each of the static NAT statements reflecting the external address to the server. I've thought about it, and it seemed to me that the problem was that policy NAT statement must be the first statement of NAT (it is the last one) so that it is run first and all traffic destined to the VPN to the Sonicwall (destination 10.159.0.0/24) tunnel would be properly treated. If I left him as the last statement, then the other static NAT statements would prevent a part of the 10.159.0.0/24 network-bound traffic to be correctly routed through the VPN.

  So, I tried first to my stated policy NAT upward in the ASDM GUI interface. However, moving the declaration was not allowed. Then I tried to delete the five static NAT statements that point to the server (an example is above) and then recreate them, hoping that would then move up the policy statement NAT. This also failed.

  What Miss me?

  Hello

  I assumed that we could have changed the order of the 'static' , the original orders, but as it did not work for some reason any then it seems to me that you suggested or change, that I proposed should work.

  I guess that your purpose was to set up static political PAT for the VPN for some these services, then static PAT of public network access, then static NAT to policy for the rest of the network in-house.

  I guess you could choose any way seems best for you.

  Let me know if get you it working. I always find it strange that the original configuration did not work.

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• public static nat/global vs

  Excluding an access list, what is the difference between:

  NAT (inside) 1 172.16.5.10 net 255.255.255.255

  192.168.5.10 (outside) 1 global net 255.255.255.255

  and

  static (inside, outside) 1 192.168.5.10 172.16.5.10 net 255.255.255.255

  Thank you.

  in static reality must be combined with the access list for a two-way communication... You are right in a sense that

  public static nat/global access-list =

  Basically, the rule is that the traffic is allowed more high to low infterface of default security

  BUT

  from the lowest to the highest security of communication you need an access as well as the STATIC list

  Thank you

  Nadeem

• ASA problem inside the VPN client routing

  Hello

  I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.

  Here are a few relevant config:

  network object obj - 192.168.245.0

  192.168.245.0 subnet 255.255.255.0

  192.168.245.1 - 192.168.245.50 vpn IP local pool

  NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary

  Out of Packet trace:

  Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33

  Phase: 1

  Type: ACCESS-LIST

  Subtype:

  Result: ALLOW

  Config:

  Implicit rule

  Additional information:

  MAC access list

  Phase: 2

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 192.168.245.33 255.255.255.255 outside

  Phase: 3

  Type: ACCESS-LIST

  Subtype: Journal

  Result: ALLOW

  Config:

  Access-group acl-Interior interface inside

  access list acl-Interior extended icmp permitted an echo

  Additional information:

  Phase: 4

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Phase: 5

  Type: INSPECT

  Subtype: np - inspect

  Result: ALLOW

  Config:

  Additional information:

  Phase: 6

  Type:

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Phase: 7

  Type: NAT

  Subtype:

  Result: ALLOW

  Config:

  NAT (inside, outside) static source any any destination static obj - 192.168.245.0

  obj - 192.168.245.0 no-proxy-arp-search to itinerary

  Additional information:

  Definition of static 0/x.x.x.x-x.x.x.x/0

  Phase: 8

  Type: VPN

  Subtype: encrypt

  Result: ALLOW

  Config:

  Additional information:

  Phase: 9

  Type: CREATING STREAMS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  New workflow created with the 277723432 id, package sent to the next module

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: allow

  There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.

  Check if the firewall is enabled on your host from the client ravpn and blocking your pings.

• {} Public static

  Boy, it is difficult in 53 and feeling totally stupid, but Java can do it for me.

  I; have my head wrapped around statics and constants and static methods, and I found (thankfully) one of the examples which allowed me to analyze step by step to better understahnd the language (it's my best course).

  However, it baffles me: things wrapped in JUST {} public static.  I've been Googling like crazy, but all the explanations are either variables or class, not fopr this thing.

  Here is an example of the MemoryDemo example I discuss:

  // Statics -------------------------------------------------------------------------------------
  private static Random _random;  To generate random numbers for dates and channels.
  private static ubyte [] _letters; To generate random strings.
     
  // Constants -----------------------------------------------------------------------------------
  private static final int MIN_STRING_LENGTH = 3;   Minimum length for a random string.
  private static final int MAX_STRING_LENGTH = 10;  Maximum length of random string.
     
  public static
  {
  _random = new Random();
  _letters = new ubyte [MAX_STRING_LENGTH];
  }
  

  So, I understand not statements made by the statics and constants... no problemo.

  But what is the reasoning behind the encapsulating the _random and _letters inside the {} public static?  Is it just a kind of shorthand for something else?

  Again, I apologize for what must seem like stupid question, but I don't want to jump on something that I think moight be crucial to understand.  Thanks in advance (again)!

  -John

  I don't see why initialization that you see in this class could not be done as you suggest.

  However, there are other situations where this isn't the case.

  For example not elegant and simple (there are other better ways to dong that), you can have a static value that identifies whether the device is a touch screen,

  If you have

  public static boolean IS_TOUCH_SCREEN;

  public as well as any other class can test this just by using .IS_TOUCH_SCREEN

  {public static

  String pattern = DeviceInfo.getDeviceName ();

  If [(model.startsWith("95"))

  IS_TOUCH_SCREEN = true;

  } else {}

  IS_TOUCH_SCREEN = false;

  }

• PhoneListener cannot access a public static vars initialized in the main thread

  Using the emulator (SDK 4.7, phone model 9500)

  I have a class PhoneListener defined and recorded, he gets the phone events without any problems. It's all public static public var that is initialized in the main thread is always null when it is examined in the context of the PhoneListener callback thread, when examined in the main thread or a son they are defined.

  I guess since the PhoneListener callbacks are called from a system thread, it cannot access the battery of my request - it seems correct? is this in any way about this?

  I tried Application.getApplication () .invokeLater (...), but validated all executable from the PhoneListener recalled suffers from the same problem.

  Thanks - Lindsay

  Exactly, that's what I was wondering - I found the answer according to the PhoneListener in the MIDlet . Now I store my UiApplication object in the running store and access them from the PhoneLister to publish objects on my main application via invokeLater.

  Thank you

  Lindsay

• Strange static problems.

  I have a PIX of four ports, inside, outside, dmz1, dmz2.

  DMZ1 use 192.168.200.0, dmz2 use 192.168.100.0

  There are a few static commands configured like this.

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  static (inside, dmz1) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  static (inside, dmz2) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  -We're not dmz1 hosts do 192.168.x.x hosts within the network.

  -I also NAT/Global installation for 192.168.200.0 for outside access.

  OK, now hosts on DMZ1 (i.e. 192.168.200.10)

  can communicate with all 10.x.x.x hosts inside.

  But no traffic happens on the outside.

  If I remove the 192.168.0.0 static (inside, dmz2) command, dmz1 guests out.

  Why?

  With this command:

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  you say the PIX as the entire network 192.168.0.0/16 is connected inside interface, what's not. When a package arrives in the PIX, the PIX uses the translation table to see what that interface to send it to. Using a static command creates a permanent entry in the table of translation of the PIX, so when a package arrives in the PIX to 192.168.200.x the PIX inside interface, NOT the dmz1 interface will pass. This translation entry overrides the routing table and even directly configured subnet, so it is essential that you get your correct static.

  If you have no other subnets of 192.168.0.0 connected inside interface, then you will need to add a specific for 192.168.200.0 translation saying that he is on the dmz1 interface, or create several static instructions defining the 192.168.0.0 network except 192.168.200.0 and 192.168.100.0.

  Statics are read from top to bottom, so if you have this in your config file:

  (dmz1, dmz2) static 192.168.200.0 255.255.0.0 192.168.200.0 255.255.0.0

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  static (inside, dmz1) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  static (inside, dmz2) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  then one will be read first and all should work OK. You may need to clear out your static existing and then cut and paste that all back in to get them in the right order. DMZ1 will still not be able to get inside.

• DMZ static problem

  I have a host in a dmz to I access a host on our internal network, static (inside, outside) 192.168.10.3 192.168.51.2 netmask 255.255.255.255.

  I have a second host, 192.168.51.3, I want to allow 192.168.10.3 for access. I know that I can't apply depending on static, static (inside, outside) 192.168.10.3 192.168.51.3 netmask 255.255.255.255, such that it will create a conflict with the first static.

  What is the best way to accomplish what I'm doing? According to me, Miss me something really simple.

  Thank you.

  Depending on how your script looks like what you need is:

  static (inside, outside) 192.168.10.0 192.168.51.0 netmask 255.255.255.0

  and then use the ACLs on the external as interface:

  permit ip host 192.168.10.3 access list acl_in 192.168.51.2

  permit ip host 192.168.10.3 access list acl_in 192.168.51.3

  The rate of HTH pls!

• Help on parameters public static function

  Hello

  I have two functions in the same file, how can I use the first function as a default value in the second function.

  public static function get decimalFormatter1 (): {NumberFormatter

  //

  }

  I have try this:

  public static void secondFunction(param1:String,_param2:Int=0,_ _param3:Function=decimalFormatter1_):Array {}

  //

  }

  Error:-1047: unknown parameter initializer or isn't a compilation constant.

  Any ideas?

  Thank you!

  To work around the problem, you can use null as default, where null means "use the decimalFormatter1. You have to write something like

  public static void secondFunction(param1:String,_param2:int_=_0,_param3:Function_=_null):Array
  {

  trainer: function var = null;

  If (param3 is nothing)

  Formatter = decimalFormatter1;

  ....

  }

• Help with public static functions.

  Hey everyone, I worked on a problem for a while and have finally understood just wrong. Google is not helped me to find the right way, so I'm posting it here. I sort of understand what's wrong with my code, but I have no idea how to do right. I'm a total noob to AS3, this is my first project.

  I have a main FLA file called game.fla with nothing on the stage, starting with. The document class is Main.as (shown below). The main class is supposed to manage the switching between the preLoader, mainMenu and game itself. The preloader loads and the player must press play to go to the main menu. The main menu is controlled by MainMenu.as, which adds event listeners for buttons game, instructions and credits. At the present time, instructions and credits just draw responses. When you click on play, I want to remove the mainmenu (not a problem with parent.removeChild (this)); and add the game. This is my problem comes in. I can't say parent.addChild (game), because honestly, I don't know how (I need to set a variable in hand or MainMenu and must it be public, static, etc?). Simplicity seems to be a function called initializeGame() that I could simply call of mainMenu. Problem: I have to do a static function, which doesn't let me use addChild, removeChild or any other variable that I create. Could someone please explain how I could do this job (even if it means change my structure. "I would be happy to learn a better way to deal with this kind of thing). Also, on a side note: if I can't use the static function with add or remove a child, can I optimize the effect later? I want later in my game, that I would need to call functions between classes, on a button click, for example, that affect the scene (or objects in the scene). Can I do it another way? For example, by clicking on an icon of the video game card clip, I would map the movieclip to load. A function that could be described seems the best way to do it, but I'm sure he can otherwise. Thank you much in advance. My code is below.

  Main.As

  package
  {
      import flash.display.MovieClip;
      import flash.events.Event;
      import flash.events.MouseEvent;
  
      public class Main extends MovieClip
      {
          private var preLoader:PreLoader;
          private var mainMenu:MainMenu;
          private var game:Game;
          
          public function Main()
          {
              preLoader = new PreLoader;
              addChild(preLoader);
              preLoader.gotoAndStop(1);
              addEventListener(Event.ENTER_FRAME, barLoading);
          }
          private function barLoading(event:Event):void
          {
              var total:Number = stage.loaderInfo.bytesTotal;
              var loaded:Number = stage.loaderInfo.bytesLoaded;
              preLoader.loadingBar.scaleX = loaded/total;
              
              if (loaded==total)
              {
                  removeEventListener(Event.ENTER_FRAME, barLoading);
                  preLoader.gotoAndStop(2);
                  preLoader.doneLoading.addEventListener(MouseEvent.CLICK, doneLoading);
                  loaded = null;
                  total = null;
              }
          }
          private function doneLoading(event:MouseEvent):void
          {
              preLoader.doneLoading.removeEventListener(MouseEvent.CLICK, doneLoading);
              mainMenu = new MainMenu;
              addChild(mainMenu);
              removeChild(preLoader);
          }
          static public function initializeGame():void
          {
              game = new Game;
              removeChild(mainMenu);
              addChild(game);
          }
      }
  }
  

  MainMenu.as

  package
  {
      import flash.display.MovieClip;
      import flash.events.Event;
      import flash.events.MouseEvent;
  
      public class MainMenu extends MovieClip
      {
          
          public function MainMenu()
          {
              playGameButton.addEventListener(MouseEvent.CLICK, playGameButtonFunction);
              instructionsButton.addEventListener(MouseEvent.CLICK, instructionsButtonFunction);
              creditsButton.addEventListener(MouseEvent.CLICK, creditsButtonFunction);
          }
          private function playGameButtonFunction(event:MouseEvent):void
          {
              playGameButton.removeEventListener(MouseEvent.CLICK, playGameButtonFunction);
              instructionsButton.removeEventListener(MouseEvent.CLICK, instructionsButtonFunction);
              creditsButton.removeEventListener(MouseEvent.CLICK, creditsButtonFunction);
                          
          }
          private function instructionsButtonFunction(event:MouseEvent):void
          {
              instructionsButton.removeEventListener(MouseEvent.CLICK, instructionsButtonFunction);
              trace("instructions");
          }
          private function creditsButtonFunction(event:MouseEvent):void
          {
              creditsButton.removeEventListener(MouseEvent.CLICK, creditsButtonFunction);
              trace("credits");
          }
      }
  }
  

  In addition, anny comments on my coding habits and how to improve are welcome.

  in the hand

  var preloader: Preloader = new Preloader (();)

  preloader.addEventListener ("preloadCompleted", preloadCompletedF);

  in the Preloader, loading complete:

  this.dispatchEvent (new Event ("preloadCompleted"));

• Public static long serialversion uid in doubt?

  Salvation in serializable classes we are declaring the serialversion as ' private public static long ' field. but when the object is serialized static values don't are not serialized, so at the other end when we are deserializing how the virtual machine works Java checks whether the serialvesrsion when it is serialized is the same as serialvesrsion in the class, when it is deserialized?

  It happened again, but not as part of a serialized instance.

• Public static LOV

  Hello!
  (Version 4.0.2 of the APEX)
  
  I need definition LOV that returns multiple values for a display value. For example, when I select the return value TV is 1, when I select RADIO return value is 2. And when I select what I want to return to the 1 and 2 values.
  
  List of values definition should be something like this:
  
  STATIC: All; (1,2), TV, 1, RADIO, 2
  
  Is this possible? Without any plugin, like SuperLov...
  
  Thank you!

  Dark salvation,

  Maybe this thread could help?

  Public static LOV

  Kind regards
  Sandro

• public static function return an object instance

  create or replace
  Item_object OBJECT TYPE IS
  (item_title VARCHAR2 (60))
  , item_subtitle VARCHAR2 (60)
  FUNCTION CONSTRUCTOR item_object
  RETURN SELF AS RESULT
  FUNCTION CONSTRUCTOR item_object
  (item_title VARCHAR2, VARCHAR2 item_subtitle) RETURN SELF AS RESULT
  , Public STATIC FUNCTION get_item_object (item_id NUMBER) ITEM_OBJECT RETURN
  MEMBER RETURN VARCHAR2 to_string FUNCTION)
  CANNOT BE INSTANTIATED NOT FINAL;
  
  
  create or replace
  TYPE item_object BODY IS
  Item_object FUNCTION CONSTRUCTOR RETURN self AS RESULT IS
  point ITEM_OBJECT: = item_object ('generic Title', 'Generic subtitle');
  BEGIN
  me: = item;
  RETURN;
  END item_object;
  Item_object FUNCTION CONSTRUCTOR
  (item_title VARCHAR2, VARCHAR2 item_subtitle)
  RETURN SELF AS RESULT IS
  BEGIN
  Self.item_title: = item_title;
  Self.item_subtitle: = item_subtitle;
  RETURN;
  END item_object;
  * STATIC FUNCTION get_item_object (item_id NUMBER) RETURN ITEM_OBJECT IS
  point ITEM_OBJECT;
  CURSOR c (NUMBER item_id_in) IS
  SELECT item_title, item_subtitle FROM point WHERE item_id is item_id_in;
  BEGIN
  I'm IN c (item_id) LOOP
  agenda: = item_object (i.item_title, i.item_subtitle);
  END LOOP;
  RETURN of goods;
  END get_item_object; *
  FUNCTION MEMBER to_string RETURN VARCHAR2 IS
  BEGIN
  RETURN ' ['|] [Self.item_title |'] ['|| [Self.item_subtitle |'] " ;
  END to_string;
  END;
  
  Impossible to compile static function get_item_object, can anyone help me please?

  user6446424 wrote:
  all instances of the object, as all the rows in the table

  I think you misuderstand objects. Objects do not come from thin air - it must exist somewhere or should be constructed from the data. Your function constructs the table utem data object. If you have any item in the table, which should be used?

  SY.

• public static const even as public static var

  Is it the same thing to use

  public static const

  as

  public static var

  technically, no.

  a const value cannot be changed.  value of var can be changed.