DMZ static problem

Similar Questions

• public static problem (inside, outside)

  I use a PIX to isolate a subnet to a corporate network.

  inside is the corporate network

  outside is not approved LAN

  A single user in LAN not approved need to go to a specific set of IP addresses in

  And all other users can browse the Internet via downstream

  proxy server to talk to the corporate proxy server

  It works fine,

  Why I can't use the static suite for this

  public static 159.182.111.0 (Interior, exterior) 159.182.111.0 netmask 255.255.255.255 0 0

  problem is that I have to continue to add each ip address static statement such as

  public static 159.182.111.50 (Interior, exterior) 159.182.111.50 netmask 255.255.255.255 0 0

  public static 159.182.111.60 (Interior, exterior) 159.182.111.60 netmask 255.255.255.255 0 0

  public static 159.182.111.70 (Interior, exterior) 159.182.111.70 netmask 255.255.255.255 0 0

  public static 159.182.111.80 (Interior, exterior) 159.182.111.80 netmask 255.255.255.255 0 0

  Unfortunately this site VIEW use different IP addresses in the subnet, everyday

  Is any limitation of this ststic command at the low security access

  interface high security by using the static command

  Hi, I don't know, but the problem may be in the netmask in your static instruction,

  It must be 255.255.255.0 or so because it is a network and not a host.

  hope this helps.

• 'static' problems after 6.1 to 6.3

  Hi all

  We have a pix with and outside the X network interface box. There is static for the web, mail applied etc.

  We also have static for network Y on the same interface. The ISP router takes care of routing. Everything works very well.

  I upgraded the box of 6.1 to 6.3 and none of the static on the network are no longer works. I get a lot of log messages ' deny entering (no xlate), but the book makes no sense (they are all guests known inside). This specific one is a management SNMP polling station a remote site.

  Refuse the entrant (no xlate) udp src inside:10.1.0.7/1054 dst inside:10.8.158.46/161

  Static on network X is functioning normally.

  I then started 6.1 and everything is OK again.

  Does anyone have an idea what I'm missing here?

  Thank you very much

  Jacques

  Hi, Jacques

  I would just take a wild guess here. PIX is connected to the external router, the interface of the router to the PIX has a primary IP address on network X and secondary IP network address Y. After the upgrade to 6.3 (1) If you do a "show arp" on the router, you would see a few incomplete ARP entries for any IP address on the network Y, for which the PIX should be proxy ARPing for... And yet, if you're doing a "show xlate global y.y.y.y", where "y.y.y.y" is an IP address on the network, you see the correct xlate allocated on the PIX... It seems to me that you can run in the bug ID CSCeb06082; See below for more details (loging ORC) required:

  - CSCeb06082: pix does not respond to arps of secondary ip:

  http://www.Cisco.com/cgi-bin/support/Bugtool/onebug.pl?BugID=CSCeb06082

  Sorry if it's too late! I hope this helps, however. Please rate this message if the information helped you solve your problem.

  Thank you

  Federico Rodriguez

• Satellite P200 - random noise hiss/static problem

  I have a Toshiba Satellite P200-1ee and it keeps hiss/static random noise if I'm not typing or computer?

  I'm just a novice, but it drives me crazy - I have not connected any external speakers or headphones someone could help me please?

  Thank you

  slaterslady

  Hola amigo

  One of my friends has a Satellite P200 also, but he never noticed something like that
  It s no static sound or something not like this

  What operating system do you use? Did something change in sound settings I hear the speaker and microphone internal.

  I have Realtek Sound Manager preinstalled on my laptop. Here I can activate the option eliminate the microphone and speaker whistles.

  Maybe you should check this.

• Strange static problems.

  I have a PIX of four ports, inside, outside, dmz1, dmz2.

  DMZ1 use 192.168.200.0, dmz2 use 192.168.100.0

  There are a few static commands configured like this.

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  static (inside, dmz1) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  static (inside, dmz2) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  -We're not dmz1 hosts do 192.168.x.x hosts within the network.

  -I also NAT/Global installation for 192.168.200.0 for outside access.

  OK, now hosts on DMZ1 (i.e. 192.168.200.10)

  can communicate with all 10.x.x.x hosts inside.

  But no traffic happens on the outside.

  If I remove the 192.168.0.0 static (inside, dmz2) command, dmz1 guests out.

  Why?

  With this command:

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  you say the PIX as the entire network 192.168.0.0/16 is connected inside interface, what's not. When a package arrives in the PIX, the PIX uses the translation table to see what that interface to send it to. Using a static command creates a permanent entry in the table of translation of the PIX, so when a package arrives in the PIX to 192.168.200.x the PIX inside interface, NOT the dmz1 interface will pass. This translation entry overrides the routing table and even directly configured subnet, so it is essential that you get your correct static.

  If you have no other subnets of 192.168.0.0 connected inside interface, then you will need to add a specific for 192.168.200.0 translation saying that he is on the dmz1 interface, or create several static instructions defining the 192.168.0.0 network except 192.168.200.0 and 192.168.100.0.

  Statics are read from top to bottom, so if you have this in your config file:

  (dmz1, dmz2) static 192.168.200.0 255.255.0.0 192.168.200.0 255.255.0.0

  static (inside, dmz2) 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  static (inside, dmz1) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  static (inside, dmz2) 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0

  then one will be read first and all should work OK. You may need to clear out your static existing and then cut and paste that all back in to get them in the right order. DMZ1 will still not be able to get inside.

• LAN to LAN VPN with NAT - solved!

  Hello world

  I have problems with a VPN L2L is implemented and logged, however when traffic comes from the other side of the tunnel it is not the host to internal network using a static NAT. Inside host 172.18.30.225 is current NATted to yyy.30.49.14 which is an IP address on the DMZ (yyy.30.49.0 255.255.255.240) Interface.

  Here is the configuration

  object-group network NET Tunnel
  network-host xxx.220.129.134 object

  Access tunnel list - extended ACL permit ip host yyy.30.49.14 object-group NET Tunnel

  correspondence address card crypto MAP_Tunnel 20 Tunnel-ACL

  the Tunnel-iServer-NAT object network
  Home yyy.30.49.14
  network of the Tunnel and drop-in iServer object
  Home 172.18.30.225

  network of the Tunnel and drop-in iServer object
  NAT (internal, DMZ) static Tunnel-iServer-NAT

  I hope that it is enough for someone to help me.

  Thank you

  M

  Version 8.3.1 ASA

  Post edited by: network operations

  The internal host does live on the network DMZ or internal? If she lives on the internal network, you can not NAT to the DMZ to interface and make it out of the external Interface, assuming that the external interface is the interface of VPN endpoint. If you terminate the VPN on the DMZ interface and the internal host lives on the internal network, then that's fine.

• Satellite A30 714 bent pin USB

  I seem to have bent a PIN in one of the two USB ports. I'll fix it myself, but does anyone have any documentation on how I disassemble the laptop?

  I am confident in the work (welding, static problems, etc.) it's just that there are often hidden screws/tabs/etc who stop work being straight forward.

  Any help would be appreciated.

  Concerning

  Tony

  Hello Tony

  Everything is at your own risk. In my view, it is clear to you. Anyway, there is no public document disassembly A30. I tried to find something similar for my old Satellite P20 but unfortunately without success.

  Simply start by dismantling the procedure and if you have still some concrete problem post. Don t lose a few screws! ;)

• Monitor intermittently do not wake from sleep mode

  I have a new Pavilion 500 - 205t Windows 7 Desktop (two weeks).  Two days earlier, after the computer is in mode 'sleep', the computer would wake up, but the screen would not.  I contacted HP Support and they said not to put the computer in mode 'sleep', but to turn it off instead.  They said that the computer could accumulate a static charge which could prevent the monitor to wake up from sleep mode.  Their solution was to force a shutdown by pressing the power switch, unplug at the back of the Tower, by pressing the power switch for 20 seconds, plug everything back in and then turn on the computer.  The monitor worked correctly then wake up from sleep mode.  For the last two days, the computer would wake properly from sleep mode.  Today, the same thing happens again.  This time, I turned off the computer and then he turned back to (without unplugging everything) and the monitor worked correctly.

  Here's my question:

  Is it really a static problem? (It has been cold and dry here for several weeks and static is high)  Or I have a hardware problem or software that needs to be fixed?  Thank you for your time.

  I think I found the solution to this problem for my computer.  I changed the settings for sleep or sleep 'Hybrid' or 'Hibernate' is allowed.  Since then, I have not experienced the problem.  I also changed what does the power button, so that when I press the power button, the computer shuts down normally.  This prevents a "forced" shutdown if the problem happens again.

  Thanks again Bill, for your time.  I mark this problem is resolved.

• OptiPlex 980 MT - amber error code 134

  Good evening. I'm sure it's dead, but I'll give it a go...

  I have lights Orange error showing 134 constant at the front of the tower. I removed the chips of memory one at a time and tried to start with one, then the other and without any memory. And finally back again with the two seated in their slots. The same code of 134 all the time. And it won't start at all.

  Is he dead? It's holiday and after hours. You're my only hope guys, otherwise this is the chat for Dell at 08:00.

  Hope the weather is good, wherever you are.

  Bev

  OK, the problem has now been fixed.

  I rang Dell support this morning and talked through it all. We was told to delete all tracks including k/b, the mouse and the monitor and the power cable, then discharge the residual power. That was pretty much as you described except that rereading what you said above I didn't properly follow what you had said.

  In any case I was told then connect power cable and start the computer nothing another home. And it seemed to start as usual. We then told me to plug the monitor and mouse and k/b, connect as usual.

  I then restarted and connected as normal. Job done. I was told that it was a "static" problem

• NAT-XLATE-FAILURE on the VPN from Site to site connection.

  I had configured a VPN of Site to new site on my network, once I created Tunnel appears, but there is no traffic when I made trace packet its gave me error "(NAT-XLATE-FAILED), NAT has failed."

  Here is the configuration runing.

  ASA 9.1 Version 2
  !
  ciscoasa hostname
  activate 2KFQnbNIdI.2KYOU encrypted password
  names of
  IP local pool kecdr 10.100.1.1 - 10.100.1.50 mask 255.255.255.0
  local pool KECVPN 10.2.1.200 - 10.2.1.225 255.255.255.0 IP mask
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 168.187.199.66 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  10.2.1.1 IP address 255.255.255.0
  !
  interface GigabitEthernet0/2
  nameif DMZ
  security-level 50
  IP 10.60.1.2 255.255.255.0
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  passive FTP mode
  DNS domain-lookup outside
  DNS lookup field inside
  management of the DNS domain-lookup service
  DNS server-group DefaultDNS
  Name-Server 8.8.8.8
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.100.1.0_26 object
  255.255.255.192 subnet 10.100.1.0
  network of the NETWORK_OBJ_10.2.1.192_26 object
  255.255.255.192 subnet 10.2.1.192
  network of the NETWORK_OBJ_10.13.0.0 object
  Home 10.13.0.0
  network of the NETWORK_OBJ_10.2.0.0 object
  host 10.2.0.0
  network of the NETWORK_OBJ_10.3.0.0 object
  Home 10.3.0.0
  the DM_INLINE_NETWORK_1 object-group network
  host object-network 10.2.0.0
  object-network 10.60.1.0 255.255.255.0
  inside_access_in list extended access permitted ip any4 any4
  inside_access_in list of allowed ip extended access all 10.60.1.0 255.255.255.0
  outside_access_in list extended access permitted ip any4 any4
  allow global_access to access extensive ip list a whole
  DMZ_access_in of access allowed any ip an extended list
  DMZ_access_in list extended access permit ip any interface inside
  outside_cryptomap list extended access allowed host ip DM_INLINE_NETWORK_1 10.3.0.0 object-group
  permit access ip host 10.2.0.0 extended list outside_cryptomap_1 10.11.0.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  management of MTU 1500
  MTU 1500 DMZ
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow any response echo inside
  ICMP allow any echo inside
  ICMP allow all DMZ
  ICMP allow any echo DMZ
  ICMP allow any response to echo DMZ
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.2.1.192_26 NETWORK_OBJ_10.2.1.192_26 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.100.1.0_26 NETWORK_OBJ_10.100.1.0_26 non-proxy-arp-search to itinerary
  NAT (inside DMZ) static source a whole
  NAT (inside, outside) static source NETWORK_OBJ_10.2.0.0 NETWORK_OBJ_10.2.0.0 NETWORK_OBJ_10.13.0.0 NETWORK_OBJ_10.13.0.0 non-proxy-arp-search of route static destination
  NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_10.3.0.0 NETWORK_OBJ_10.3.0.0 non-proxy-arp-search of route static destination
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in in interface outside
  inside_access_in access to the interface inside group
  Access-group DMZ_access_in in DMZ interface
  Access-Group global global_access
  Route outside 0.0.0.0 0.0.0.0 168.187.199.65 1
  Route DMZ 10.1.0.0 255.255.0.0 10.60.1.1 1
  Route DMZ 10.2.0.0 255.255.0.0 10.60.1.1 1
  Route DMZ 10.60.0.0 255.255.0.0 10.60.1.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication LOCAL telnet console
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 10.0.0.0 255.0.0.0 inside
  http 0.0.0.0 0.0.0.0 outdoors
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set pfs Group1
  peer set card crypto outside_map 1 196.219.202.197
  card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto outside_map 2 match address outside_cryptomap_1
  peer set card crypto outside_map 2 185.52.118.67
  card crypto outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 allow outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet 0.0.0.0 0.0.0.0 outdoors
  Telnet 10.0.0.0 255.0.0.0 inside
  Telnet 10.2.0.0 255.255.0.0 inside
  Telnet 10.1.0.0 255.255.0.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH 10.0.0.0 255.0.0.0 inside
  SSH 10.2.0.0 255.255.0.0 inside
  SSH 10.1.0.0 255.255.0.0 inside
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  internal GroupPolicy_185.52.118.67 group strategy
  attributes of Group Policy GroupPolicy_185.52.118.67
  Ikev1 VPN-tunnel-Protocol
  internal GroupPolicy_196.219.202.197 group strategy
  attributes of Group Policy GroupPolicy_196.219.202.197
  Ikev1 VPN-tunnel-Protocol
  internal kecdr group policy
  attributes of the strategy of group kecdr
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  internal KECCISCO group policy
  KECCISCO group policy attributes
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  internal KECVPN group policy
  KECVPN group policy attributes
  value of server DNS 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
  cisco 3USUcOPFUiMCO4Jk encrypted password username
  username privilege 15 encrypted password 3ofqMXhysxFRHhoQ keccisco
  type tunnel-group kecdr remote access
  tunnel-group kecdr General-attributes
  address kecdr pool
  Group Policy - by default-kecdr
  kecdr group of tunnel ipsec-attributes
  IKEv1 pre-shared-key *.
  type tunnel-group KECVPN remote access
  attributes global-tunnel-group KECVPN
  address kecdr pool
  Group Policy - by default-KECVPN
  IPSec-attributes tunnel-group KECVPN
  IKEv1 pre-shared-key *.
  type tunnel-group KECCISCO remote access
  attributes global-tunnel-group KECCISCO
  address KECVPN pool
  Group Policy - by default-KECCISCO
  IPSec-attributes tunnel-group KECCISCO
  IKEv1 pre-shared-key *.
  tunnel-group 196.219.202.197 type ipsec-l2l
  tunnel-group 196.219.202.197 General-attributes
  Group - default policy - GroupPolicy_196.219.202.197
  IPSec-attributes tunnel-group 196.219.202.197
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  tunnel-group 185.52.118.67 type ipsec-l2l
  tunnel-group 185.52.118.67 General-attributes
  Group - default policy - GroupPolicy_185.52.118.67
  IPSec-attributes tunnel-group 185.52.118.67
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call
  HPM topN enable
  Cryptochecksum:8156993fef96da73dedfaacd7a14e767
  : end

  My local IP address: 10.2.X.X

  My remote IP address: 10.3.X.X

  Can anyone support me for the error

  Hello

  Your self after dynamic PAT takes the static NAT...

  NAT source auto after (indoor, outdoor) dynamic one interface

  You must reconfigure you NAT or PAT rule defined in your firewall.

  no nat source auto after (indoor, outdoor) dynamic one interface

  network local-lan-pat1 object

  10.2.0.0 subnet 255.255.255.0

  NAT dynamic interface (indoor, outdoor)

  !

  network local-lan-pat2 object

  10.60.1.0 subnet 255.255.255.0

  NAT dynamic interface (indoor, outdoor)

  !

  no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_10.3.0.0 NETWORK_OBJ_10.3.0.0 non-proxy-arp-search of route static destination
  !

  outside_cryptomap to access extended list ip 10.2.0.0 allow 255.255.255.0 host 10.3.0.0 255.255.255.0

  No list of extended outside_cryptomap access not allowed host ip DM_INLINE_NETWORK_1 10.3.0.0 object-group

  !

  We hope that you do this between subnets... not for the host at the other end.

  Concerning

  Knockaert

• Anchor WLC in DMZ, FW does not support mulit-static Rts.

  Hi gang,.

  Not looking for someone to hold me hand, but you can use some advice.

  We work through our deployment of a WLC guest. Our WLC anchor is in our DMZ.

  Management and the AP Manager are on the same subnet. The dynamic interface "VLAN" is on a different subnet from the other interfaces, and its Portal is the DMZ Firewall interface.

  Problem, the firewall does not support multiple static routes.

  Always do the management and dynamic interfaces must be on different subnets?

  Someone at - it experience with this type of configuration?

  I understand the value of the time, if I appreciate honestly all help I get.

  Best regards

  Larry feet

  Just to clarify, we're talking wireless access visitor right? Wired not invited?

  Wired allows you to create a custom in a vlan port specific necessary (but not when you configure this on the controller of anchorage)

  In any case... just make sure that the WLAN you want to dock is configured the same as on the controller of the DMZ. Make sure you anchor this controller to the DMZ and make sure you anchor the wlan dmz to himself.

• PIX 515 DMZ problem

  Hello

  We have some difficulty in moving traffic in and out of a Cisco PIx 515 firewall. We use it with two demilitarized. The first DMZ has a mail in her Server (before end mail server) that communicates with a different mail server (back end mail server) inside, it is called DMZ1. The second DMZ (DMZ2) has some users who are expected to pass through the firewall to the outside and use the internet and must have access to the e-mail DMZ1 server. Inside users must be able to use the Internet and can access DMZ1. Here's the important part of our Setup.

  What we were doing, we can correctly access from inside, inside users to access internet permit to join the DMZ1 e-mail server and the mail in DMZ1 server the inside. Our problem is that we are unable to browse the internet on the DMZ1 Messaging server if we put DMZ1 as gateway ip address on that server and the address ip of the DNS of the ISP is propely located on the same machine. Also, we could not do DMZ2 users browse the internet, although we allowed the www Protocol in the fromOut access list. One last question, can we do the DMZ2 a DHCP server on the interface on the PIX and do distribute ip addresses to users on that subnet only? Thanks for any help in advance.

  6.3 (3) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  Auto interface ethernet2

  Auto ethernet3 interface

  !

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif ethernet2 dmz1 security50

  nameif ethernet3 dmz2 security40

  !

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  !

  names of

  !

  IP outside X.Y.Z.163 255.255.255.248

  IP address inside 192.168.0.9 255.255.255.0

  dmz1 192.168.10.1 IP address 255.255.255.0

  IP address dmz2 192.168.20.1 255.255.255.0

  !

  fromOut list of access permit icmp any host X.Y.Z.162 source-quench

  fromOut list of access permit icmp any host X.Y.Z.162 echo-reply

  fromOut list of access permit icmp any unreachable host X.Y.Z.162

  fromOut list of access permit icmp any host X.Y.Z.162 time limit

  fromOut list access permit tcp any host X.Y.Z.162 EQ field

  fromOut list access permit tcp any host X.Y.Z.162 eq telnet

  fromOut list access permit tcp any host X.Y.Z.162 eq smtp

  fromOut list access permit tcp any host X.Y.Z.162 eq www

  !

  fromDMZ1 list of access permit tcp host 192.168.10.2 192.168.0.0 255.255.255.0

  fromDMZ1 list of allowed access host ip 192.168.10.2 192.168.0.0 255.255.255.0

  !

  fromDMZ2 list of access allowed tcp 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0

  !

  pager lines 24

  !

  Outside 1500 MTU

  Within 1500 MTU

  dmz1 MTU 1500

  dmz2 MTU 1500

  !

  Global (outside) 1 X.Y.Z.164 netmask 255.255.255.248

  Global (outside) 2 X.Y.Z.165 netmask 255.255.255.248

  NAT (inside) 1 192.168.0.0 255.255.255.0 0 0

  NAT (dmz1) 1 192.168.10.2 255.255.255.255 0 0

  NAT (dmz2) 2 192.168.20.0 255.255.255.0 0 0

  static (inside, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

  static (dmz2, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

  static (dmz1, external) X.Y.Z.162 192.168.10.2 netmask 255.255.255.255 0 0

  !

  Access-group fromOut in interface outside

  Access-group fromDMZ1 in interface dmz1

  Access-group fromDMZ2 in the dmz2 interface

  Route outside 0.0.0.0 0.0.0.0 X.Y.Z.161 1

  Hi jamil,.

  There is a sentence on the URL I sent you, you can now activate dhcp option within the interface. Just check this...

  REDA

• NET writing DMZ problem

  Hi all

  I had the problem is image NET copy running-config DMZ writing to the laptop, but does not, my order is:

  WR net 172.16.2.1:test

  That the error message is below:

  Write TFTP to 172.16.2.1 on interface1 test

  Time out, trying to connect

  [not]

  But I cannot ping terminal the 172.16.2.1, after that I have to copy the running-config LAN (172.16.1.1) can made, using the same notebook.

  Is - not the dregs interface1, interface2 DMZ problem? should I change it? pls advise

  Stanley

  What is the global configuration or static access-list and nat for that 2 interfaces?

  sincerely

  Patrick

• PIX 525 6.3 (1) worm. & static IP problems

  I have problems, change a static IP address of internal IP addresses.

  The original statement looked like this,

  static (DMZ, external) xxx.xxx.46.3 192.168.1.2 mask subnet 255.255.255.255 0 0

  When I change the external ip address to point to another internal IP address.

  static (DMZ, external) xxx.xxx.46.3 192.168.1.3 netmask 255.255.255.255 0 0

  the new address is listed, but the external IP still points to the old internal address. I can't fix the problem until I reboot the PIX.

  Is this some kind of a cache problem.

  Martin,

  You have a chance to implent the logical interface (virtual interface)?

  As you can see, 6.2 (2) pix does not support virtual interface; However, 6.3 (1) don't. To answer your question, after you have done the configuration, you must use

  clear xlate command to clear all the translations. I hope this would help you.

• WRT120N problem static IP setting

  My ISP gives me a static IP address

  IP 172.17.158.183

  MASK 255.255.252.0

  GW 172.17.156.255

  There is a problem affecting the 172.17.156.255 bridge in WRT120N. He says it's bad gateway.

  My mobile network settings work, but how do I set up WRT120N to work with this network settings?

  You are not right.

  Using the search I found solution fo my problem.

  http://homecommunity.Cisco.com/T5/wireless-routers/bug-report-CIDR/m-p/311698/highlight/true#M163772

  And it is working very well now.

  There is a bug in the scripts that check the gateway, mask, and IP.