Put BIOS in place the utility

Similar Questions

• How to use the utility to update (uefi) BIOS HP

  Notebook: G62 a10em

  I downloaded the BIOS update tool from http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063 & lc = on & cc = us & dlc = in & sw_lang = & product = 4226...

  and it is installed on my USB key.

  Now, how can I update my bios?

  The USB key contains now:

  BIOS

  | - Current (empty folder)

  | - New (empty folder)

  | - Previous (empty folder)

  BIOSUpdate

  -CryptRSA.efi

  -CryptRSA32.efi

  -HpBiosUpdate.efi

  -HpBiosUpdate.s09

  -HpBiosUpdate.sig

  -HpBiosUpdate32.efi

  -HpBiosUpdate32.s09

  -HpBiosUpdate32.sig

  my current version of bios is f. 08

  I did a cut above.

  After looking at the appropriate file you downloaded, it says this:

  "Prerequisites .
  -Microsoft .NET 2.0 is required. UEFI and Custom Imaging - the HP BIOS update must be run from a FAT or FAT32, partition with a volume of the "HP_TOOLS" name This Installer gives you the option to install on the hard disk (HDD) or USB. If you install on the HARD disk and the HP_TOOLS partition is not present, Setup prompts to create the HP_TOOLS partition. If you install on a USB key, Setup renames the partition on the USB in HP_TOOLS. If you use a custom image, you can create the HP_TOOLS partition manually with the type FAT32 and that the volume HP_TOOLS name. ATTENTION:-the UEFI system partition is not protected and can be removed. -Backup of the computer by using the complete PC Backup feature of Microsoft Windows Vista does not save the UEFI system partition. For these reasons, HP recommends that you place no additional data on the UEFI system partition. Because the partition is not backed up, corruption or failure of the partition will result in the loss of all data on the partition, as well as the loss of UEFI functionality. "For more information, visit: www.hp.com/go/techcenter/startup"

  There is little documentation on how to use it, but a Member here figured it out.

  http://h30434.www3.HP.com/T5/operating-systems-and-software/envy-14-system-recovery-doesn-t-work-with-latest-BIOS/m-p/328684/highlight/false#M45165

  using Windows 7:

  Just plug in the USB key and then run the SPnnnnn.exe BIOS file downloaded from the Web site drivers HP.

  Assuming that the USB is configured correctly (see below), Setup the BIOS sees the HP_TOOLS partition on the USB, copy of the BIOS and its file signature on the USB key, then run Setup winflash. The system BIOS detects the USB and the partition HP_TOOLS and the BIOS is magically updated.

  I put in place a new USB key as follows:

  1 rename the partition HP_TOOLS from the hard drive to something different like HP_TOOLSbak

  2. Plug the USB

  3. Download and run the utility to update the BIOS (not the BIOS, still) drivers HP support page.

  4. Select the option to install to a USB

  5. Select the option to create the partition HP_TOOLS

  6. The reader should now be formatted as HP_TOOLS with a record of Hewlett-Packard containing BIOS and BIOSUpdate records. The BIOS folder contains empty current, news and previous records.

  7 download and run the HP System Diagnostics (UEFI) MS drivers HP support page

  8. Select the option to install on a USB key. This will create a SystemDiags folder under the Hewlett-Packard folder

  9. Download and run the HP Notebook System BIOS update for the HP support page drivers, given that the USB is correctly tagged it will install the update of the bios on the USB drive

  10, we have to end up with a HP_TOOLS partition on the USB drive identical to the one that you removed from the hard drive.

  Once you have configured the USB drive, you can upgrade to other versions of BIOS (most recent or oldest) using this drive, as I mentioned above: just plug in the USB and then download and run the BIOS Setup program.

  Having said that I'm not sure of what you do, once you boot the USB drive.

  .

• Tecra 8200: update BIOS: the utility is not available in V86 mode?

  I want to update bios for Tecra 8200, but is to show "the utility is not available in V86 mode."

  Please help me

  Hello

  James is quite right. To use this device there is only an update of the traditional BIOS available. If you want you can consult the FAQ update of the BIOS page. You can find it under http://www.toshiba-tro.de/gcc/biosinfo/index.html

  Good luck!

• When I try to bookmark a new page, I don't get the window of "Page bookmarked or edit this bookmark. I t place the site in my favorites, but I have to go to "organize" bookmarks in order to put it where it belongs.

  When I try to bookmark a new page, I don't get the window of "Page bookmarked or edit this bookmark. I t place the site in my favorites, but I have to go to "organize" bookmarks in order to put it where it belongs.

  Which extensions you have installed?
  It seems to me that some sort of 'social bookmarks' extension changed this window edit this bookmark, based on the presence of this line of "Rating" at the bottom.

• ProDesk 600 G1 BIOS configuration of the TPM secure through the BIOS Configuration utility

  We have a range of devices, computers HP desktop and laptops in our environment.  Devices are all running Windows 7 64 bit and should have Bitlocker enabled, but we found that some were not encrypted.  So I am trying to set up a remote BIOS and Bitlocker config activate software that we can get out via SCCM and then embed in a task sequence image for new machines.

  I use the Bios HP Configuration utility to check a BIOS password is set and then activate the TPM chip.  I took a BIOS config output of each of our models and created a settings file that has all of the TPM associated parameters of all models.

  At the moment I run Setup BIOS utility manually for testing.  On all models I tried that works very well, except for the 600 ProDesk G1 SFF.

  When I run the utility on the ProDesk 600 G1 MFS, it says that I have managed to update the settings, and when I check the BIOS, the TPM secure has been unhidden and the TPM Management was given to the operating system (two settings I change), but the TPM itself remains hidden.

  It's the release of the BIOS configuration utility (it uses the 2.60.13.1 version, which uses plaintext passwords.  I also tried with the 3.0.13.1 later version that uses password files - same result)

  C:\ > BiosConfigUtility64.exe /cspwd: "password" set: "TPM_Config.REPSET"
  
  < BIOSCONFIG Version = "2.60.13.1" Computername = 'HP600G1' Date = "24/07/2014" Time = "13:01:37 ' UTC '1' = >"
  
  < SETTING changeStatus = "pass" name = "Embedded Security Device" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [hidden device]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [device]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "Enable security on the next boot" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "The BONES of on-board safety management" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SUCCESS msg = "Successfully set BIOS config." / >
  
  < information msg = 'BCU return the value' real '0' = translated = '0' / >
  
  < / BIOSCONFIG >
  
  C:\ >

  And after a reboot (where it should activate the TPM), BIOS shows as disabled built-in safety device (see attachment for the image).

  I have tried everything I can think of to get this to activate, including:

  • Different versions of the BIOS configuration utility
  
  
  • Remove the password from the BIOS and the application in the same order as the parameters
  
  
  • Different passwords
  
  
  • Reboot and allowing the machine to start completely to Windows before checking if the setting took effect

  I also tried to add the utility and the commands for an SCCM package and it works directly and as part of a sequence of tasks to see if that makes a difference, but nothing I've done has activated the TPM module.

  I know that the TPM module works, as you can turn it on manually and then Bitlocker can be applied to the machine, but with thousands of devices in our environment, I need to get this job without the need for manual intervention.

  Has anyone else had this problem and found a solution?  Or has someone at - he managed to activate the TPM on the SFF of 600 ProDesk G1 using the BIOS Setup utility?  Any ideas / suggestions would be very appreciated!

  P.S. This thread was moved from the company PC - Compaq, Elite, Pro for HP PC Client management. -Hp moderator of the Forum

  This problem has now been resolved by HP.
  
  They provided a replacement motherboard for the test machine I was using that solved this problem. I don't know what kind of motherboard failure could prevent the activation via the script TMP chip but not prevent activation through the BIOS menu, but as a replacement solved the problem, then it must be a hardware failure.

• 22-3020: updating the BIOS with the utility HP - big mistake

  I have a model all-in-one 22-3020 who Support Assistant who kept harassing me to do a BIOS update.  I followed the instructions, he made a back-up and then the utility went down.  When you are finished, I continued to use the computer without a problem.

  The next morning, I got a white screen, waved the mouse to activate the standby mode screen (I guess) and if the computer was on, I couldn't any screen.  I restarted the computer (several times) with no screen.  Then, I searched this problem on Google and found a recommendation to hit the F10 key for 8 seconds, arrow down 3 times, and then press enter two times.  It was suggested that the BIOS update has somehow got stuck in standby mode.

  I tried without success and took the computer to a local repair center who told me that they couldn't access the BIOS to go back, or set.  In short, they said that the assistant to Support HP probably brick my computer and I would probably need to replace the motherboard.  I'll pass.

  Can anyone offer any other suggestions on how to try to restart the computer?  Is it possible to connect another monitor using the USB or HDMI so I can see if the F10 key is me to get into the BIOS (although I suppose that the repair people who would have thought).

  I'm the only one who has had my computer in brick by this utility that comes on the computer?

  Any help appreciated.

  You have a 1 year warranty. Call HP support.

  If you live in the United States / CA, coordinated HP here.

• is there anyway to remove it saying that parental controls have been turned on for a user account? is not defeat the purpose of putting them on in the first place?

  is there anyway to remove it saying that parental controls have been turned on for a user account? is not defeat the purpose of putting them on in the first place?

  is there anyway to remove it saying that parental controls have been turned on for a user account? is not defeat the purpose of putting them on in the first place?

  Hello

  Why she would frustrate the object?

  If the child is a Standard recommended account and you are using an administrator account, the standard account cannot change Parental controls.

  Concerning

• I need to put in place the security of the laptop running finance and don't know the programs and the finest details of it.

  Security

  I need to put in place the security of the laptop running finance and don't know the programs and the finest details of it. I need to buy, sell and subscribe. I need to use programs such as paypal also.

  You have antivirus installed? If this isn't the case, I would install Microsoft Security Essentials (MSE) for you antivirus protection.

  http://Windows.Microsoft.com/en-us/Windows/products/security-essentials

  Windows 7 is really quite safe as is and does not need a lot of work to ensure.  There are a few FixIt who can put in place and ensure that it is set using the recommended security settings.

  http://support.Microsoft.com/mats/windows_security_diagnostic/en-us

  http://support.Microsoft.com/mats/Malware_Prevention/en-us

  http://support.Microsoft.com/mats/ie_performance_and_safety/en-us

  Just run the fix it is and install MSE and you should be sure resonably.

• I want to streamline my signature process sending.  I have the code I entered in my document to place the signature on the form.  Y at - it a code or a setting that I can put to automatically enter the address email of the person to whom I am

  I have the code I entered in my document to place the signature on the form.  Y at - it a code or a setting that I can put to automatically enter the address email of the person who I send the form?  Also, I would use my own default message for the signatories.  Is there a place that I can get that think so I can't copy and paste the message every time?  I still need to sign first, and therefore a default section with my choice and message to signatory would be great.

  Hello Kevin,

  From now on, you cannot set the recipient's e-mail address in the document itself or let him choose automatically. You must provide either the Web portal or even using the API, the e-mail address of signatory manually. According to the models of message, if you have account level business, you can set it by going to the tab account-> account settings-> Message template,.

  Kind regards

  -Usman

• How to put in place the new Airport Express to extend the current wireless WiFi U-Verse home network?

  Hello

  What are the steps for the creation of a new AIRPORT EXPRESS MC414LL/A Terminal so that it make that expand my network existing wireless, using my current AT & T UVerse equipment home.  Here are the details...

  Internet service provider: AT & T U-Verse

  Existing facilities: primary AT & T provided router/Modem: ARRIS NVG589 (reference 587234-004-00) that manages my house wired and wireless Wi - Fi.

  PROBLEM: Does not offer full Wi - Fi coverage

  SOLUTION: Attempt to add a new Terminal Airport Express so that it will extend coverage of the existing Wi - Fi network wireless.  I plan on the use of certain features such as streaming my content from iTunes to my sound, surround sound, etc Airport Express Library.

  NEW FEATURE: APPLE AIRPORT EXPRESS 802.11n Wi - Fi PART # MC414LL/A

  I wish I had AT & T equipment to continue to manage the Wi - Fi and network functionality (DNS, firewall, etc.), as it currently does.  However, I want to use the Airport Express to extend Wi - Fi coverage.  I already have a cable ethernet from the floor and the AT & T ARRIS NVG589.  I just need to know how to set up my new Apple Airport Express.

  Thank you!

  With the Express connected to Arris gateway with Ethernet, you have the basis for a roaming network.

  I would recommend that you run the AirPort Utility and allow it to run automatic installation of the Express. The utility should detect that the Express is connected by Ethernet and go through the steps to properly set up. Note: If you have made any changes to the Express since out of the box, I strongly suggest that you first perform a 'factory' reset on it to make sure that the installation went well.

• BIOS cannot detect the drive msata

  I am trying to use an msata player in my m4700 precision but not very successful. I tried to use Crucial and mushkin in msata/WWAN slot. BIOS simply ignores the card. I heard he was trying ever since that it took a while for BIOS finished to start if I put the card.

  But he alread card list mini SSD to be {none}

  Does anyone have a similar experience?

  Thanks for the help

  Packers dell offers a compatible dell certified msata card 256. .they delivered oriinally previous systems portable and with samsung pm830 256Go msata cards... samsung msata are not currently available for resale this invintory is used by OEMs, I was personally able to source 2 new samsung 256 GB msata (MZMPC256HBGJ - 0001D 1) via the internet outside India Mambai @ $350.00 / each you can order an msata of 256 GB of dell spare parts using the printer dell P/N MTT20 which is for a computer of dell desktop XPS 8500SE that uses also the same card 256 GB msata. Initially, I ordered a Dell, but they kept its replacement by a Liteon Dell P/n V6PN8 (LMT256M3M) 256 GB msata for the samsung pm830 msata... even you I have not specified no substitution... due to price I choose to send the dell back and keep the pm830 256Go s msata samsung... I set up my own M4700s accuracy with them 2 and one of my buddies with a 256 GB liteon you both work good... .only difference, it's the samsung seems to have better read/write speeds on the liteon... I've personally never tried a crucial msata, but I read the other posts that State they do infact on the m4700 work. Just a thought maybe your msata/wwwlan slot / port is bad or damaged or possibly the msata allignment slot on bottom of card has a Burr or incorrectly notched try a smidge to see if the pins will be properly align... Once you get the screw spindle allignment held in place of filing in the notch on the card, just a thought only other choice is to get Council MB or girl replaced by dell... Good luck, I hope do you run MAC ii

• Place the items in the table next to each other on stage

  Hey guys,.

  I know I have to do something wrong that is easy and simple to fix, but I can't fix.

  I have a table called a frame of a movieclip and I want to place each image as a 'menu' on the stage.

  The problem I have is that I want to put each item in menu next to each other, but the only code I could find work is the 3D carousel.

  So I try to adapt this code to my needs.

  Where I'm going wrong? Any help would be great.

  Code below:

  package classes

  {

  import flash.display.MovieClip;

  com.greensock.*;//for interpolation ability to import

  import com.greensock.TweenLite;

  com.greensock.easing import. *;

  import flash.filters.BlurFilter;

  import flash.events.Event;

  import flash.utils.Timer;

  import flash.events.TimerEvent;

  import flash.display. *;

  import flash.events. *;

  import flash.sampler.StackFrame;

  SerializableAttribute public class extends MovieClip MenuSystem

  {

  private var blur: BlurFilter = new BlurFilter (0,0,1);

  private var holderMc:MovieClip = new MovieClip();

  private var radiusX:uint = 1200; / / width of the carousel

  private var rayonY: uint = 400; / / height of the carousel

  private var centerX:Number = 100; / / x position of the center of the carousel

  private var centerY: Number = 350; / / the position there from the center of the carousel

  private var speed: Number = 0.01; / / initial rotation of the carousel speed

  private var itemArray:Array = new Array(); / / store the items to sort them according to their 'depth' - see the sortBySize() function.

  public var navigationPopupInfo:NavigationPopupInfo = new NavigationPopupInfo();

  public void MenuSystem()

  {

  the constructor code

  We do support for the menu system serve

  addChild (holderMc);

  holderMc.y = - 200;

  Also add a listener to control the rotation of the speed menu

  / * addEventListener (MouseEvent.MOUSE_MOVE, OnMouseMoveHandler);

  */                    }

  public function initNavigationPop (): void

  {

  TweenMax.to (navigationPopupInfo, 0, {alpha: 0, 40-y:, blurFilter: {blurX:3, blurY:10}});}})

  holderMc.addChild (navigationPopupInfo);

  navigationPopupInfo.x = (-navigationPopupInfo.width / 2);

  TweenMax.to (navigationPopupInfo, 2, {delay: 1, alpha: 1, y: 10, ease:Elastic.easeOut});})

  TweenMax.to (navigationPopupInfo, 1, {delay: 1, blurFilter: {blurX:0, blurY:0}});}})

  }

  Place the vital elements on stage

  public void initRange(numOfMenuItems:Number):void

  {

  for (var i: uint = 0; i < numOfMenuItems; i ++)

  {

  var arrayBoxItem:String = ('model' + (i + 1) + '_');

  var itemMc:ItemMc = new ItemMc();

  public var angl:Number; belongs to the class of the element.

  Item class extends ItemInner in the library FLA.

  itemMc.angl = i * (400 / numOfHomeRangeItems);

  itemMc.alpha = 0.8;

  itemMc.name = (arrayBoxItem);

  trace (itemMc.Name);

  holderMc.addChild (itemMc);

  itemArray.push (itemMc);

  itemMc.itemHitter.buttonMode = true;

  itemMc.addEventListener (Event.ENTER_FRAME, enterFrameHandler);

  Listen MouseEvents only on the icons, not on reflection;

  itemMc.itemHitter.addEventListener (MouseEvent.CLICK, clickHandler);

  itemMc.itemHitter.addEventListener (MouseEvent.ROLL_OVER, rollOverHandler);

  itemMc.itemHitter.addEventListener (MouseEvent.ROLL_OUT, rollOutHandler);

  itemMc.iconMc.gotoAndStop (arrayBoxItem);

  }

  }

  public void clickHandler(event:MouseEvent):void

  {

  clean your audience before doing anything else to release

  the user CPU resources

  for (var i: uint = 0; i < itemArray.length; i ++)

  {

  var itemMc:ItemMc = itemArray [i];

  itemMc.removeEventListener (Event.ENTER_FRAME, enterFrameHandler);

  itemMc.itemHitter.removeEventListener (MouseEvent.CLICK, clickHandler);

  itemMc.itemHitter.removeEventListener (MouseEvent.ROLL_OVER, rollOverHandler);

  itemMc.itemHitter.removeEventListener (MouseEvent.ROLL_OUT, rollOutHandler);

  Optional:;

  TweenLite.to (itemMc, 1, {scaleX:0, scaleY: 0, alpha: 0.1, ease:Elastic.easeInOut});})

  TweenMax.to (itemMc, 1, {blurFilter: {blurX:5, blurY:5}});}})

  to replace the carousel again see function reInit()

  FIND A WAY TO REMOVE ITEMS

  this.removeChild (itemMc);

  }

  Tabula Rasa, to prepare variables

  var variantName:String = event.target.parent.name;

  itemArray.splice ();

  If (variantName == "backBtn") {MovieClip (root) .reinitMenuSystem () ;}

  else {MovieClip (root) .addVariantPage (variantName) ;}

  }

  /////////////////////////////////////////////////////////////////////////////// /////////////////////// POSITION ITEMS IN CAROUSEL

  position items in the Menu

  public void enterFrameHandler(event:Event):void

  {

  Event.Target.x = centerX; / / position of the element x

  Event.Target.y = centerY / / position point y of

  Scale according to position point there to give the point of view

  / * var s:Number = event.target.y / (centerY + rayonY);

  event.target.scaleX = event.target.scaleY = s;

  Event.Target.angl += speed; / / speed is updated by OnMouseMoveHandler

  ADD DOF

  blur.blurX = - event.target.y / 10 + 21;

  blur.blurY = - event.target.y / 10 + 21;

  Event.Target.filters = [blur];

  Finally set the size of the elements

  sortBySize();

  */                    }

  /////////////

  Check the progress of ticks

  / / / TRI SIZE DETERMINE DEPTH OF ELEMENTS

  set the display list index (depth) of the elements according to their

  scaleX property so that the element, the index is high (depth)

  / * public function sortBySize (): void

  {

  It is not a property Array.ASCENDING DECLINING use and reverse()

  itemArray.sortOn ("scaleX", Array.DESCENDING |) Array.NUMERIC);

  itemArray.reverse ();

  for (var i: uint = 0; i < itemArray.length; i ++)

  {

  var itemMc:ItemMc = itemArray [i];

  holderMc.setChildIndex (itemMc, i);

  }

  }

  */

  /////////////////////////////////////////////////////////////////////////////// /////////////////////// ITEMS WHEN ROLLOVER & OUT

  public void rollOverHandler(event:MouseEvent):void

  {

  var currentModel:String = event.target.parent.iconMc.parent.name;

  Event.Target.parent.alpha = 1;

  TweenLite.to (event.target.parent.iconMc.tooltipMc, 1, {alpha: 1, y:-40, ease:Elastic.easeOut});})

  event.target.parent.iconMc.tooltipMc.tipHeader.gotoAndStop (currentModel);

  }

  function rollOutHandler(event:MouseEvent):void

  {

  Event.Target.parent.alpha = 0.8;

  TweenLite.to (event.target.parent.iconMc.tooltipMc,.5, {alpha: 0, y:-27});})

  }

  / / / ITEMS IN THE CAROUSEL MOVEMENT ACCORDING TO THE POSITION OF THE MOUSE

  /*

  Update of the speed at which the carousel turns accoring to the distance of the mouse since the center of the stage. The variable speed is only updated when the mouse is over the point Sprites.

  */

  / * function mouseMoveHandler(event:MouseEvent):void public

  {

  Speed = (mouseX - centerX) / 20000;

  }

  */          }

  }

  I have a table called a frame of a movieclip and I want to place each image as a 'menu' on the stage

  This code will take a MovieClip in your library with the link ("Menuitem") that has 5 labeled keyframes "menuitem 1 «...» "" menuitem 5 ', it is adapted accordingly to your stagesize and distribute, and align the elements at the top from left to right:

  I havemport flash.display.MovieClip;

  var menu_Array:Array = new Array();

  the var menu: MovieClip = new MovieClip();

  var stageWidth:int = stage.stageWidth;

  var menuWidth:int = 0;

  for (var i: int = 0; i<5;>

  {

  var menuItem:Menuitem = new Menuitem();

  menuWidth += menuItem.width;

  menu_Array.push (MenuItem);

  }

  function distrbuteAndAlignItems(_menu:MovieClip,_array:Array):void

  {

  var scaleFactor:Number = stageWidth / menuWidth;

  var xAdjustment:Number;

  trace (scaleFactor);

  for (var j: int = 0; j<_array.length;>

  {

  MovieClip(_array[j]).scaleX = MovieClip(_array[j]).scaleY = scaleFactor;

  for (var k: int = 0; k

  {

  xAdjustment += MovieClip(_array[j]).width;

  }

  _ARRAY [j] .x = xAdjustment;

  _ARRAY [j].gotoAndStop(j+1);

  xAdjustment = 0;

  _Menu. AddChild (_ARRAY [j]);

  }

  addChild (_menu);

  }

  distrbuteAndAlignItems (menu, menu_Array);

  
  

  If that's what you're looking for...

• Where the place / the field to enter the Web site I want to see from the opening

  I had put Mozilla in place to open the site start.earthlink.net . Now this isn't the case. What hit me out of this framework, and where can I find the dialog box reset to this place?

  See - How to set the home page

• Updating the BIOS is dead the satellite Pro P300-1AY

  Hi all

  found this forum and really hoping that he can help me!
  I bought a satellite Pro P300-1AY two years ago, it cost me £900 nr so I thought it would be worthy of a purchase.

  A year ago the USBs stopped working, I do it every working solution I could think of anything will do, finally gave up and learned to live without USBs!

  However, a few weeks ago, the laptop at the start stop, I didn't get was the black screen. Probably a video problem I did all the memory check hard drive everything else, however, it was only an intermittent problem, I found if I he tilted on the side she would begin, another thing to live with!

  But two days ago, I heard that if I've updated the BIOS, it could solve all my problems. so I went to the Toshiba site, found the BIOS updated and downloaded, but to halfway through the installation, the laptop froze and I couldn't t he put it off and had to take the battery out to turn it off!

  And ve you may have guessed, he's now won t start. Even its worst, LED lights, and if I put a disc in the cd I can hear it whirring, but that s it.

  Is - this irreparable? I ve heard of priming of the cd with the original BIOS with a combination of keys or I'm hoping against hope?
  Ty for your time in reading :)

  Hello

  > Is it irretrievably? I ve heard of priming of the cd with the original BIOS with a combination of keys or I'm hoping against hope?

  Well, usually the BIOS could once again be reflashed, but you would need a traditional version of the BIOS update.
  This version is available for Toshiba FSA.

  So you will need to get in touch with a local ASP technician that could reflash the Rom BIOS module.
  Eventually, after this update the specifications would be stable.

  Good luck

• 10 improvement of the Windows path hangs on "place the external storage and press OK.

  Hello

  This will be my first post on this forum.

  A couple of weeks ago, I bought a Toshiba SATELLITE CL10-B-103 for my son. The CL10-B-103 has installed Windows 8.1. Tonight I plan to make the installation of the Windows 10 upgrade because Windows 8.1 announced that he was ready for the upgrade.

  The trial progressed slowly but smooth and without problems until now... As the laptop is equipped with only an HD 32 GB the trial upgrade was informed that I had to stick a USB key. After that, the trial continues slowly but smoothly, but who did not question because I had all night. However after the first reboot of the system when he was about 60 or 66% of installation of process this error message showed: place the external storage and press OK. It's very strange since the key USB has been removed at all and was still in the system. It is strange, is that both the OK button as the Cancel button are not selectable. Without passing by the touchpad, not a tab or an entry.

  Some community online Windows 10 post mentions that, via the BIOS, the system must be initiated from this USB key. I tried to reboot the system with DEL, F2 or F8, but I couldn't get into the BIOS and wasn't able to change the boot sequence.

  After each "restart" the same error message appears. It does not matter that the USB is in it or not.

  So, my conclusion is that my CL10-B-103 is suspended/East in a loop. I don't know how to proceed.

  Please, I can really use some help.

  Thanks in advance.

  Because it seems that I can not only edit/change a message I am answering my own post now...

  The problem seems to be resolved. When I was able to use the touchpad I could push the OK butten and the upgrade product now.