Question about changing the refresh frequency for the perf of run-time statistics

Similar Questions

• Question about changing the type of adapter during cloning with vmkfstools

  Hello world

  It seems to me have found stuck trying to use vmkfstools-i to clone a machine, in fact the command seems to work fine except that I would like to change the screen to type hard "ide" to "buslogic" drive adapter at the same time and this is where I am stuck. That's what I tried...

  vmkfstools-i < /path/to/oldmachine.vmdk > < /path/to/newmachine.vmdk > - a buslogic

  This command is cloning my machine but when I go to the newly created vmdk file ddb.adapter type is always set to "ide" not "buslogic". It seems that the '-a buslogic "directive is ignored, or I do not understand what it is supposed to do.

  Anyone know what I could do wrong?

  Thanks in advance.

  for a disc of data-rewrite of the line ddb.adapterType = in the vmdk descriptor is sufficient.

  For a boot disk, I would also rewrite the geometry of the disk.

  I took a few notes on this subject - see http://sanbarrow.com/vmdk-basics.html#changeadapter

  How to change the type of adapter to an existing vmdk

  A vmdk can be connected to different controllers
  -IDE
  Bus-controller-
  LSI-controller-
  -SAS-controller LSI-logic
  -new paravirtualised SCSI controller

  In the description of vmdk is affected in the parameter

  ddb.adapterType =

  The description of vmdk includes only three values: "ide", "buslogic", "free".
  For all the latest as the LSI controllers - SAS use 'free '.
  If you need to change the type of adapter of a disk that is used to start a prompt, it is recommended
  for also change the geometry of the disk-.
  If the disk is used only for data alignment is not necessary.
  Remember that the type of adapter to a virtual machine is also set up in the vmx file.
  So if you rewrite an IDE-SCSI-disk do not also forget to change / check the vmx file

  ide0:0. FileName = ' ide - disk.vmdk.

  TO

  scsi0. Present = 'true '.
  scsi0.virtualDev = "free".
  scsi0:0. Present = 'true '.
  scsi0:0. FileName = "changed - disk.vmdk."

  How to calculate the geometry of the disk

  There are several reasons why you want to manually calculate the geometry of the disk:
  -change the type of an existing vmdk adapter
  -create a vmdk to a dd-file description
  -create a description of vmdk to an img file as used by Starwind
  -create a vmdk to a description *-flat.vmdk when the original description is lost

  In all cases, we must firstly the nominal size of the disk in sectors.
  Find the size of the image file in bytes.

  / 512 =

  Then decide what type of geometry: IDE or SCSI

  For disks SCSI is the typical geometry * cylinders x 255 heads x 63 sectors

  DDB. Geometry.Cylinders = *.
  DDB. Geometry.Heads = "255".
  DDB. Geometry.sectors = "63".

  To calculate the number of cylinders
  / 16065 =
  When the vmdk using adapertype buslogic or free this formula is valid for all disks greater than 1 GB capacity

  For the typical geometry IDE drives is * cylinders x 16 heads x 63 sectors

  DDB. Geometry.Cylinders = *.
  DDB. Geometry.Heads = "16".
  DDB. Geometry.sectors = "63".

  To calculate the number of cylinders
  / = 1008
  When the vmdk using adapertype ide the maximum value for is 16383.
  For all over - 8 GB - capacity discs so you can use this geometry

  DDB. Geometry.Cylinders = "16383.
  DDB. Geometry.Heads = "16".
  DDB. Geometry.sectors = "63".

• Question about changing the size of an existing column in a table

  I'm a new DBA. I wonder to change a column in an existing table that is filled with data. Our database is a 10g database, and the table name is Contacts. The column name is FName, and it is currently of varchar (10). It should be extended to VARCHAR (18). Can I use this statement: ALTER TABLE contacts COLUMN CHANGE FName VARCHAR (18)?
  
  I thank all who help me with this question in advance.

  Hello

  This is how you do it

  ALTER TABLE  A_ERROR_TABLE MODIFY(TEST VARCHAR2(18)); -- Example
  
  ALTER TABLE contacts MODIFY ( FName VARCHAR2(18));
  

  Concerning

  Published by: OrionNet on April 2, 2009 16:09: correction of typo

• Impossible to access parameters for laptop and receive an error message saying "runtime error!" Program c:windows/system32/Dllhost.exe R6034. A request did try to load the wrong C run-time library. »

  Original title: laptop - unable to access settings.

  I can't access "pc settings" on the start menu. When select, goes to white screen, returns to 'start '. Error is displayed on the desktop = "runtime error!" Program c:windows/system32/Dllhost.exe R6034. A request did try to load the wrong C run-time library. "Any ideas on how to solve this problem? Thank you

  I found the answer here http://blogs.technet.com/b/ouc1too/archive/2013/10/19/windows-app-store-doesn-t-load-after-8-1-upgrade.aspx you just have to change application manifest path, in order, to fix all other applications

• a patch can change the release date and time table psrelease?

  a patch can change the release date and time table psrelease?
  
  Thank you.

  What kind of patch? A bundle? A maintenance plan? An upgrade of the application?
  In any case, I'm sure that it does not change any date, but he has a line in this table.

  Nicolas.

• Default value of the string at run time control

  Hello world

  When I'm editing mode, I can click with the right button on a control of the chain and go under "Information Operations" and select "Make default value"... I need to do in run mode, but I can't find a property that gets the job done.

  Any suggestions?

  Thank you

  LoBa

  Hi love,

  My advice is to init the checkpoints of your application with the ini files. Do you have an API for the name VI configuration file. That way, you can change the default between every time the application runs.

  Explain here.

  Concerning

• You will have to give the value of the filter at run time condition.

  Hi experts
  
  I have a requirement in which I need to give the value of the filter at run time, for example Project_code = "XYZ"
  The XYZ value should be given at run time. How can achieve us?
  
  Thanks and greetings
  Frank

  Hi Jos,

  1. create a PROJECT_CODE to say as alphanumeric variable, as non-persistent data type and use it as a filter in your mapping.

  2 drag and drop the variable twice in your package make that as a declared variable and in the second stage that do like Variable refresh then in step 3 of your interface.

  3 generate a script and executing that give scenario the value you desired, press enter once you have given, otherwise it will not fetch the entry and make sure that the LAST VALUE is DISABLED.

  This way you can give values to the varaible running.

  Thank you
  Guru

• I use CS5.1 and cannot open it all at once. I get the prompt to get the SC6 JAVA run-time inheritance.  I installed, but still cannot open Photoshop. Any ideas?

  I use CS5.1 and cannot open it all at once. I get the prompt to get the SC6 JAVA run-time inheritance.  I installed, but still cannot open Photoshop. Any ideas?

  Would you please install Adobe Application Manager from the link below, then try again to install the application again:

  Adobe - Adobe Application Manager: for Macintosh: Adobe Application Manager

  ~ Sarika

• HP Envy 700-500z: Question about wi - fi antenna tower for the wi - fi signal booster

  Hello

  I bought a wi - fi turn antenna to boost my wireless signal so I can use my Tablet outdoors during the summer.  The instructions provided with the said Tower if the computer has built in wi - fi or wireless card, do not install the antenna tower software becauce it could cause a conflict.

  It was suggested to me that I could either turn off the card go in BIOS or go to network and sharing Center and change the settings of the map, right click on wireless icon, select Disable.  In this way, I could safely install the antenna tower software and use antennas to boost my wireless signal.

  I live in the mountains of NE PA, in a pretty remote area.  'Hot spots' are so rare.  I have no Internet DSL but the signal is not strong enough to reach my Tablet if I should be on the outside.  Even in one of the rooms, the signal is not all that strong.  So it would be great help for me, if I could push my wi - fi at least in the immediate area outside my house.

  Could someone tell me if the network settings can be sure to do, or I would return just the antenna of the tower.  I will not go into the BIOS because I fear of seriously harming my computer by doing this.  But a simple change in network settings, I'm pretty confident that I could.

  Thank you

  Sandra Knapp

  Hello Dave,

  Yes, I suppose I could do that, last spring, they have installed a new router and told me that he would have a stronger signal for wi - fi, but it did not help me using my Tablet out on the patio at all.  I couldn't get a signal here, nothing at all.  So I have a feeling they don't have anything stronger, but I could ask.

  Thank you for suggesting that.

  Sandie

• Question about upgrading the CPU for Satellite 1110-Z14

  Hello

  My satellite 1110-z14 has a processor intel mobile celeron @ 1.5 ghz. The processor is based on architecture p4 - it should be a northwood-256.
  Is it possible to upgrade the processor?

  1110-z20 is powered by the mobile celeron @ 2.0 ghz - all other technical specifications except the hard drive are the same... (ati radeon m6 with 16 MB, usb 1.1 mob and so on...).

  What do you think, can I upgrade the processor?
  Can what cpu I use?

  Thanks for your replies!

  Hello

  AFAIK the 1110 series computer is equipped with an Intel 845MZ system controller.
  I found some details about Intel 845MZ chipset on the Intel page. It must be able to manage the Mobile Intel Pentium 4 - M with 400 MHz FSB Processor
  http://www.Intel.com/products/chipsets/845MP/index.htm
  On the Intel page, you can find the entire family of the CPU.

  But generally the replacement of CPU and the upgrade is not recommended and no one can say whether the OS will run stable after these updates, so be careful.

• question about cleaning the sensor of the A57

  Dear community of Sony,

  I have several questions about the cleaning of the sensor of the A57.

  Recently, I noticed several dark specs appearing on images when shooting at low opening (F20, F22), especially when there are high for them (like the sky in a landscape photo) contrast. To my knowledge, I've categorized as possible of dust on the sensor. I have read the section of the manual about cleaning the sensor and followed the procedure. However, the problem remained. I have previous experience with cleaning of the more resistant the probe of a Sony NEX dust particles, so I applied it to the A57. I used the specialized sensor cleaning tools combining two parts kit - wet and dry. Noted little dust on translucent mirror as well, so I cleaned up afterwards. Later, I considered this mirror could have some specialized coatings.

  So my first question is: should I have done some permanent damage the mirror or the sensors? Currently, the camera works OK, although some features of dust still remain. It seems that I had pushed some of them to the edges of the sensor.

  I'm not so happy with the tool that I used. I'm thinking about this one for a more thorough cleaning:

  http://www.digitaltoyshop.co.UK/Eyelead_sensor_cleaning_kit_SCK-1_Sony_Alpha_A57_t2836_6789

  It is marketed as a tool for A57. Should I use it?

  Thank you in advance?

  Best regards Angel Marinov

  PS: I'm really happy with my Sony A57 and the NEX. They made me a fan of Sony. So, I want to use this topic to also say thank you to the developers of Sony.

  Hello Angel!

  Read the following steps carefully and let us know if you have any other questions.

• How to change the properties for some controls at run time?

  Hello

  I would like to change some properties for some controls in front of Panel at run time. Number of properties of the control I want to change is based on a newspaper user file opens in the final application.

  I've attached an example where I'm changing the visibility of digital controls. Problem I have I don't know what reference to connect to the property node in the case where the control loop for is not a digital control. The example is based on the label.text property but I could use the more generic classname property as well.

  Kind regards

  Petri

  Initially, a control has no legend.  It is not just the caption string is empty and the legend isn't visible, but the caption object does not exist.

  At the time of change, when a legend is on something other than an empty string, the object of legend is created.  If you redefine the legend with an empty string, the object of legend is deleted.

  During execution, the object of the legend cannot be created or destroyed, but if it exists, it can be changed.

  When I legends I want to change during execution, I initially affect the '. '.

• question to change the location of the server

  Hi gurus,
  
  I'm with another question.
  
  I just installed 11.2.0.3 RAC in a RedHat 5.4 server. Not this server go to travel abroad to be installed there.
  
  My question is, when the server will be connected and running, CARS will run without problems? I think that probably need to change the vip and scan ips, is good? or simply changing VIP/scan/etc/host it works? Consider another shift?
  
  Thank you

  Salvation;

  You must reconfigure certain settings based on your cluster. Mention it these docs that I shared.

  If your db is autonomous IP isn't important, you can edit the hosts file and your db can run wihtout any problems. But when the crs involved you will have to reconfigure anything on your crs

  Respect of
  HELIOS

• Change the Jpeg file taken time in the "Date" column to windows explorer for modification time?

  I just found out that JPEGs, edited and recorded by CS4 still wear their original creation time in windows Explorer, regardless of how many times they have been modified, which makes it very inconvenient and confusing, without opening the files to find out. Does anyone know how to change the setting to 'Update?' Thank you very much in advance!

  You say that you see the creation Date column in Windows Explorer, but not update?

  If this is the case, it's an easy fix...  In Windows Explorer, right click on the bar with the titles (for example, on the title the creation Date) and check the update box.  Normally the update, this is what is displayed by default Explorer for the elements of the General.  I don't know what is shown for other types of files, I use only general articles.

  What do you see when you follow these steps:

  1. right click on the folder that contains your images (in the navigation to the left).

  2. Select Properties.

  3. click on the Customize tab.

  4 what was the optimize this folder for: of the field?

  FYI, as you can see you can change folder for example, customizing the general articles for one or a whole folder tree.

  You can also make changes to one of your folders of photos, and then propagate the settings to all folders of this type in your system.  I'm really jump coming here; I would like to know if that's what you eventually want to do.

  -Christmas

• How to automatatically answer the question of "change the color space?

  After obtaining of CS4 I will often wonder if I want to change the settings of the color space of the image I want to open.

  In previous editions of SP/c, you can access the General settings and set the response to be automatically always the same (always ask/never ask/always the existing value or original...).

  Since I always want to change the color space to match the color in CS4 space I would like once again able to set as default. How can I do this in CS4?

  It is in the color settings (Edit > color settings). Change the RGB color strategy to convert RGB working. Uncheck the appropriate (or all) checkboxes in the politics of color.