Question about interfaces

Similar Questions

• A few questions about the difference between the Satellite P70, L70, S70

  Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

  (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

  (3) all the three (P70, L70, S70 series) come with the same TFT panels?

  (4) of the above series, which supports mSata?

  (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

  (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

  (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

  Thank you in advance.

  > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

  (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
  As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

  I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

  (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
  See point 1). Different P70, L70, S70 models were equipped with different material parts.

  (> 4) of the series above, which takes in charge mSata?
  As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

  (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
  See point 4) not all models supports the same hardware specifications

  (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
  I don t think that SATA III is supported. I guess it would be SATA II

  (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
  Not easy to answer because there are too many models released in Europea.
  And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.

• Question about lights LED R7000

  Question about this quote from the Manual: "when the router is turned on, the light during approximately 10 seconds and then turn. If all lights lit, this indicates a fault in the router"my router lights LED is turned off. Are they supposed to? I discovered how manually to disable using genius. NETGEAR Nighthawk AC1900 is defective?

  I think the manual means just that at first they all turn on, then off for a few seconds. LED lights depending on what services are available.

  The power light should stay lit. Port LAN LED come on if a device is connected the WiFi LED (Amber on white, 100 M, 1000 m), are we if the radios are turned on. The Wan or the internet LED lights up if there is a connection to the internet. Some of them you can turn off via the user interface, but it is handy to have on so that you know the status.

  It looks like your router working normally.

• Just a quick question about the appearance of the cluster

  Hello, this is Matthew, just a quick question about the appearance of the cluster

  Is there anyway to rearrange the order of the elements? I know cutting automatic resizing, I could move the items by hand. But if I use the cluster somewhere else, I have to move the items again...

  What I want is of the order of "Mx My Mz Ax Ay Az Temp voltage CS".

  Is there a quicker way to deal with?

  THz so much!

  You can right-click the border of the cluster and choose "arrange control cluster...". "The user interface is not as intuitive as it could be, but it will allow you to reorder items. If you use the cluster in several places, you should make the cluster in a type definition and replace all current uses of the latter with the type definition, so that they all match. They will also update automatically when you make changes to the type definition. Otherwise, you could have a situation where you have multiple groups with the same data types, but with elements in a different order, and your data will be getting a new denominated, when wire you the whole clusters. The data will be in the same order, but given that the item labels are in a different order, you can't get the data you want, when ungroup you by name.

• Question about the issue of the Double NAT...

  Hah I posted for a little.  I have a question about Double NAT.  Is it wise to launch?  Reason why is that I have a WRT54G v6 router and the Zoom ADSL X 4 Modem/Router/gateway and it seems that sites take just a little more time to respond to Web sites.  I just want to know I have to turn off (i.e., go in with my router bridge Mode) or what.  Or leave it alone.  Now one last thing: that the problem of slow could actually be AT & T but I have the feeling that this isn't.

  What configuration options you have on the Zyxel to fill? What have you tried exactly?

  The basis for the first option is:

  * Bridged Zyxel.

  * Linksys configured for PPPoE with your user name and password for the internet connection.

  Instructions to fill the Zyxel are here or here depending on the exact model of Zyxel.

  The second option is:

  * Zyxel doing business as the router. I assume here that the Zyxel is on 10.0.0.2 with a subnet mask 255.255.255.0.

  Unplug the Linksys to the Zyxel. Connect a computer to the Linksys. Open the web interface of the WRT to http://192.168.1.1/

  On the main Setup page:

  1. change the LAN IP of 192.168.1.1 address 10.0.0.1.

  2 disable the DHCP server.

  3. save the settings. You will lose the connection. Unplug the computer.

  4. wire one of the numbered LAN ports of the Linksys for the Zyxel. Do not use the internet port of Linksys!

  Now you should be able to open the Linksys web interface to http://10.0.0.1/ all devices connected wireless of Linksys or connected to one of the three LAN ports must have a connection to the internet via the Zyxel.

• Questions about apps headless

  Hello

  I have questions about the apps without head:

  -It is possible to run or end "game without head" of the apps 'part of the UI "?

  -When headless app is running, the part "headless" have opportunities to perform automatically the part "user interface"?

  -It is possible for "headless" to use geolocation and the sound?

  In advance, thank you for your answers.

  -It is possible to run or end "game without head" of the apps 'part of the UI "?

  Yes

  -When headless app is running, the part "headless" have opportunities to perform automatically the part "user interface"?

  Yes, being the easiest invocation

  -It is possible for "headless" to use geolocation and the sound?

  Yes

• General question about the Browser element

  Will look for an alternative, I found the Browser element and now I have a few questions about that:

  As I am not yet experienced on the Interfaces of Java development, I was wondering if following senario is possible:

  Have some HTML Pages which do the job of the Interface.

  If you submit a form, the JAva Base program (the Master application) process all Information.

  If you are viewing a list, the info is from a json of the Base program output.

  As the Communication Server Client HTML, the only difference is, that all communications remains inside the app.

  Is this possible?

  I can't speak to the idea of dealing with the entry of html, but I can confirm that it is possible for an application program to create a html page and providing the BrowserField for display.

• Various Questions about wireless access controller

  Help me please with these fundamental questions about the role of the access (AC) wireless controller.

  Assume that the access controller and Access Point are connected via IP:

  -Wireless frames sent to AP to acre; include the original MAC header (on the way to wireless access)?  If Yes, is there a Cisco AC gets to fill the WLAN and LAN it is plugged (which means that it outputs as ethernet frames as if they were issued by Mobile Stations).

  -Is the AC necessarily the default gateway for mobile stations? I guess not. But it is possible the default gateway?

  The Cisco AC can function as a DHCP relay?

  The AP creates a tunnel to the controller. All IP traffic from the AP to the controller will address the AP source and dest IP to the interface of the Manager of the AP on the controller. The wireless client traffic is encapsulated inside this tunnel. When it hits the controller the CAPWAP is removed leaving the customer's original package to be sent to the local network through the controller.

  The controller should not be the default gateway for wireless clients because it is not a router. Think of it as a device that converted into wired wireless traffic.

  Normally, the controller acts as a proxy DHCP. Once the customer has joined a WLAN, the controller sends the DHCP packets to the DHCP server on behalf of clients such as the IP address of assistance normally configured on the router for cable customers. You can also configure the controller to act as a DHCP server for wireless clients.

• Question about the connection of a customer VPN ASA

  Hi guys,.

  I have a question about Tunneling VPN. I have an ASA 5505 with static PPPoE address external and local 192.168.202.0/24 network, operates as an EasyVPN server. On the other side is an another ASA 5505 without dynamic PPPoE outside interface acting as EasyVPN customer in customer ode. The internal network is 192.168.1.0/24

  It works very well! But now, I created another user who uses EasyVPN client software to connect to the EasyVPN server. This works as well.

  But how am I able to connect customer network 192.168.1.0/24 on the connections of the ASA?

  Please give me a hint.

  "But how am I able to connect customer network 192.168.1.0/24 on the connections of the ASA?

  Yes, if you set the ACL of split tunnel correctly you should be able to connect to the remote client ASA.

  Please follow the method of configuration of Cisco doc split tunnel, at the bottom of the link.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• (Basic) question about layers

  Hi all!

  I'm a little Photoshop-beginner and I have a question about layers, just as the title suggests. I have a bunch of PNG files which are the design of what happens in the UI (user interface) for an app Anyhow, I need to break down each graphic element in the files (for example, the logos, the "buttons", the small images) in different layers. How this is done more efficiently?

  Any help would be much appreciated and I hope that I have explained the task well, but if you need additional information about the files or the task, I will be happy to provide that.

  Thanks in advance,
  EM

  Use the Quick Selection tool to select each item and then press Ctrl + J (Cmd + J) that will create a separate layer. You can select with the rectangle selection rectangle if you want straight borders. Each item will have a transparent background which will allow you composite with other pictures or blank documents. Click on the symbol of the eyeball in the layers palette to the right to turn on and off and then you can view layers individually.

• Consider purchase of Wacom Cintiq 27 HD Touch - Questions about the tactile feature in Photoshop and Lightroom

  I'm considering buying a 27 HD Touch of Wacom Cintiq monitor. I have a few questions about the two programs Adobe and their use of the 'touch' feature - Photoshop CS6 and Lightroom 5.7 running on Windows 7.

  1 problems related to touch a feature in Lightroom and Photoshop CS6 and 5 resolved that you see on the forums of Wacom a year ago?

  2. If so, is there sufficient value gained through the tactile feature in Photoshop CS6 and Lightroom 5 to justify the $500 price difference between the Cintiq 27 HD vs Touch HD? (I realize that this is a subjective question based on the abundance of its cash).

  3. I intend to stay with CS6 as long as possible to avoid a monthly subscription, BUT I wonder if buy the Touch HD can provide additional key features in future releases of these products that do not exist currently. (It is a pie in the kind of sky in question).

  Thank you!

  Kent

  Support for Photoshop Touch is added by CC 2014.2.2.  However as the Pro Intuos Wacom tablets with touch can be used with earlier versions of Photoshop and the Wacom Tablets Configurator can custom features can be used with Photoshop touch tablets.  I use LR but I don't know that the same thing would be true for her. You can configure the setting for many applications. The device driver knows which application its interfacing with and uses the parameter set for each...

  I have disable most of touch when using Photoshop.  The main reason why I have a Tablet is Photoshop Brush tools. Like Eraser, clone stamp, etc, nothing is better then a pen when it come to create the layer mask.  For most programs, I always use a mouse and I use the keyboard, the mouse and the pen with Photoshop...

  I never wanted a Cintig I do not have my hand between my eyes and the work. I'm not an artist.

• Question about the purchase of policies in China for commercial purposes

  I have several questions about the purchase of policies. Our company is in CHINA

  1. we have our own product which has LCD display to display certain information with different languages (Chinese, English, German, French, Italian, Spanish, Portuguese and Russian). We need to use Adobe Heiti Std fonts for the Chinese language by commercial purposes. I tried this font in Adobe? Do Folio police 11.1, but is not in this library, your partner gold in China told me this font is part of Adobe Production Premium CS5.5, which we have already purchased from Adobe, it is used freely by the user.

  It is true that we can use the fonts Adobe Heiti Std freely and even for commercial purposes in many products?

  If this font is not free, how can I buy it for commercial purposes in many products? Could be he you pls tell me the person/company contact email or phone number.

  2. we need to use Eurostile LT font for the English language by commercial purposes as well. Is it Eurostile LT available for German, French, Italian, Spanish, Portuguese and Russian as well? and I can not find do Folio 11.1 as well. But some Eurostile Std * fonts appear in the list.

  Use font Eurostile LT? freely for user

  The police in the Adobe product package, but it is not in the Adobe typotheque (Adobe? Do Folio 11.1), then it can be used freely even for commercial purposes in many products?

  Thank you in advance.

  Unfortunately, none of these fonts is available for the user interface of the product. Although Adobe has two of them, we have not the right to sell OEM licenses or the other.

• Question about to go to a State.

  Hello, I have a question about to go to a State. Is there a property that I can apply to objects that is executed when you visit a State?

  For example, I have a button that switches the State "Biography" and "Biography" contains an Image. How can I make the "glow" image or add effects to it whenever the State is visited?

  Thank you!

  Hello

  You can add effects to your buttons and elements of user interface on your condition by listening for the event onEnterState States. When your switces State of the current state of your particular State where you will like to add effects on its user interface elements so you can add in this event related to the event onEnterState handler.

• Questions about the accordion component

  I have a few questions about the use of the accordion component:
  
  1. when my accordion is created it shows the first container child, this child is created at this time and if you go to another child it is also created (but only until it is first accesed). The thing in the first child, I need to access the properties and components located in other children, so it marks an exception to NULL, because I am trying to access the properties or the components that have not yet been created, but I really need to access and transmit values to other children containers at the moment (without their first navigation) , then it is possible to create all the children while creating the accordion although I would'nt need to navigate through its children to create them?
  
  2. is it possible to disable the functions of click of an accordion, so the only way to change bewteen her children is programmatically? I mean, you can click the buttons on the accordion to navigate through his children, but you can also do this programmatically by using the selectedIndex property, so I'll try to disable accordion buttons so the only way to navigate is programmatically.
  
  All the ideas of these two questions?
  

  You can use creationPolicy = "all" on the accordion and it will create all children, not only the first condition. The downside of this is that your application will have a little more time to start. Consider this:

  Child 2:
  

  If you try to set child2.input = 'something', a better solution would be to use data binding:

  Child 2:
  [Bindable] public var inputValue:String;
  

  Now you can do: child2.inputValue = 'something '; If the user interface of child2 have not been created, the inputValue parameter has without adverse consequences; as soon as the 2 child controls are created, data binding will assign the value. If child 2 has already been created, the data binding will also affect the value.

  You can disable the click event to the accordion by intercept and stop its spread, but you must do this in ActionScript, you can't do this in MXML.

  myAccordion.addEventListener ('change', accHandler, true); true means to use the capture phase

  private void accHandler (event:flash.events.Event): void
  {
  If (event.target is mx.containers.accordionClasses.AccordionHeader) {}
  Event.stopImmediatePropagation;
  }
  }

  The idea is that intercept you the click event, as it moves down through the components (capture phase). If the target of the event is an AccordionHeader, prevent you the event to go further - it is to reach the AccordionHeader itself.

  You can put this handler on accordion or its parent up to the Application.

• Question about AP Autoinvoice and macthing the invoice?

  "Hi Forum - I have a question about accounts payable" * pay on reception Autoinvoice * "program.
  
  The question: Does autoinvoice program match invoices against PO, or do I need this to do it manually after running this program?
  
  
  Thanks in advance!

  Hello

  You have not need manually match invoices to the BP.

  The standard functionality of the remuneration to the receive function is as mentioned below:

  You can set up your vendors to pay upon receipt or delivery, and you can choose the level of consolidation of bills: paid site of landslide, a reception or packaging provider.

  After receipt or delivery operations are created, you can submit reception AutoInvoice compensation program to automatically import the invoices corresponding to the corresponding purchase orders.

  When the Payables open Interface import process is complete, you can then validate and pay these bills to order using the processing of payments of accounts payable standard feature.

  I hope this helps.

  Thanks and greetings
  Jeanny.