Question of burden

Similar Questions

• Sansa Clip + Question of burden (with mini USB cell phone charger)

  I have a few questions about the issue of workload:

  • is it acceptable to fresh clip + use the charger of mobile phone with mini USB socket (5v ~ 700mA), as I know, USB 2.0 specification is 5v ~ 500mA?
  • Sansa is equipped with a circuit to handle the charging process, for example the the blackout when the battery is fully charged?
  • After that several hours connected to the computer, the turn display self... is this normal? (so I have to press a button to see the screen saver and check the State of charge)

  Thanks for the answer of my question... hehhe

  You can use any charger, but be sure that it is 5V and not higher than (above will FRY your Clip).  Around 350 my and especially (even if some 500 my and above is best) is very well - the Clip will use the amperage he needs.

  Yep, you can disable the data pins and everything should be ok.  Just be sure you know what you're doing on the pins.  Many people say to be able to arrive at the same end simply by inserting the USB cable into the computer, not completely or by covering the data pins.  In addition, you can buy USB charge cables only - I have a couple of people.

  Note that when you connect to your computer, you can still read the Clip files, via the computer itself (not the music) and media playing software that is pointed and play the songs on the Clip.

• Plugged in, do not question of burden with windows Lenovo Yoga2 Tablet

  Hi all

  Need help with my windows lenovo yoga2 tablet. It shows the message as "plugged in, not load ' and the battery goes down to zero. Unable to fix earlier discussed using solutions since my battery cannot be purchased.

  Kind regards

  Riou

  The problem is solved finally. The culprit was the cable that came with the pack of USB. I replaced it with my Moto X cable that is thicker than that which is expected and my tablet started to load

• Pavilion G6 2303-TX: plugged in, do not question of burden

  After connecting the charger connected display, do not load...
  its getting charged in the stop mode.

  Hello

  Try the following.

  First, shut down the laptop, unplug the power adapter, remove the battery and then hold the Power button for 30 seconds.

  Now, plug in the AC adapter without the battery inserted, start Notepad, open windows control panel, open Device Manager, expand the entry for the battery, on the right, click on and compatible Microsoft ACPI control method battery and select Uninstall - do uninstall not something else here.  When the uninstall is complete, shut down the laptop, unplug the AC adapter, reinsert the battery and then reconnect the AC adapter.

  Start Notepad - Windows will automatically reinstall the driver.

  Kind regards

  DP - K

• FDMEE question of burden HFM

  Hi all

  I am facing a problem loading the file from FDMEE to HFM (11.1.2.4 version). I am able to complete all the steps in the workbench.  However, once the export step towers work bench, if I even get overlaps existing in the HFM's ".dat" file, I can see nothing. FDMEE journal indicates that the records were assigned the HFM. I copied the log file for the load less than. I checked the load adjustment allow, it is set to Yes. I have an Access administrator for FDMEE and administrator of access applications in HFM. Is there anything else I should check in order to load data. Appreciate any thoughts on this issue.

  2016-01-11 11:29, 783 INFO [AIF]: process FDMEE: 77, log level: 4, log file: \\75612-AWA\fdmee1\Data\outbox\logs\SPDEV_77.log

  2016-01-11 11:29, 783 INFO [AIF]: place: NtzGL (Partitionkey:3)

  2016-01-11 11:29, 784 INFO [AIF]: name of the time: Jul-2015 (period key: 7/31/15 12:00 AM)

  2016-01-11 11:29, 784 INFO [AIF]: name of the category: real (category key: 1)

  2016-01-11 11:29, 785 [AIF] INFO: name of rule: NtzGL (rule ID:7)

  2016-01-11 11:29:02, 097 [AIF] INFO: Version FDM: 11.1.2.4.100

  2016-01-11 11:29:02, 097 [AIF] INFO: log the file encoding: UTF-8

  2016-01-11 11:29:04, INFO 009 [AIF]: - START IMPORT STEP -

  2016-01-11 11:29:04, 063 [AIF] INFO: - END IMPORT STEP -

  2016-01-11 11:29:04, 117 [AIF] INFO: - EXPORT STEP START.

  2016-01-11 11:29:04, 318 INFO [AIF]: file name: dummy.txt

  2016-01-11 11:29:04, 336 [AIF] INFO:

  Move the data for the period "Jul-2015".

  2016-01-11 11:29:04, INFO 365 [AIF]: run the following script: D:\Oracle\Middleware\EPMSystem11R1/products/FinancialDataQuality/bin/HFM_EXPORT.py

  2016-01-11 11:29:04, 668 INFO [AIF]: name of the Cluster: DEV3

  2016-01-11 11:29:04, 975 INFO [AIF]: run the following script: D:\Oracle\Middleware\EPMSystem11R1/products/FinancialDataQuality/bin/HFM_LOAD.py

  2016-01-11 11:29:05,084 INFO  [AIF]: ************************************************************************************

  2016-01-11 11:29:05, 084 [AIF] INFO: * HFM_LOAD.py started for LoadID: 77

  2016-01-11 11:29:05,085 INFO  [AIF]: ************************************************************************************

  2016-01-11 11:29:05, 294 INFO [AIF]: name of the Cluster: DEV3

  2016-01-11 11:29:05, INFO 438 [AIF]: connected to: SPDEV

  2016-01-11 11:29:09, 509 INFO [AIF]: load data started: 11/01/2016 11:29:05.

  2016-01-11 11:29:09, 509 INFO [AIF]: load data completed: 11/01/2016 11:29:05.

  2016-01-11 11:29:09, 522 [AIF] INFO: loaded documents: 2

  2016-01-11 11:29:11, 917 INFO [AIF]: load URL started: 11/01/2016 11:29:09.

  2016-01-11 11:29:11, 917 INFO [AIF]: loading the URL FDMEE_URL

  2016-01-11 11:29:11, 917 INFO [AIF]: URL for loading completed: 11/01/2016 11:29:09.

  2016-01-11 11:29:11,941 INFO  [AIF]: ************************************************************************************

  2016-01-11 11:29:11, INFO 974 [AIF]: - END EXPORT STEP -

  2016-01-11 11:29:12, INFO 030 [AIF]: run the following script: D:\Oracle\Middleware\EPMSystem11R1/products/FinancialDataQuality/bin/HFM_CONSOLIDATE.py

  2016-01-11 11:29:12, 282 [AIF] INFO: name of the Cluster: DEV3

  2016-01-11 11:29:12, 588 [AIF] INFO: end process FDMEE, process ID: 77

  Kind regards

  Nik

  OK, I think you need to open a SR of Oracle.

  It could be FDMEE/ODI does not HFM loading operations, may be a communication problem.

  Can you confirm that if you had load manually the data up to the intersection through the Smart view and ran the FDMEE process data would be replaced?

  Have you ever been able to load properly in this environment?

• Need immediate help

  I have a Hp Envy 15-j004tx recntly bought...

  I have a pluuged does not question of burden...

  Plugged in charge do not question or only 30 to 50 seconds and shows after the charge to boot this laptop...

  This error indicates deifferent % levels.

  When the system is off or in sleep mode extended battery charge gently, without offspring during offshore or into hibernation.

  shows only when the system is on...

  Help!

  Hi mudasar123. I understand that you are unable to charge your battery while you use it, but it seems to require during hibernation.

  It seems that you have exhausted your troubleshooting with @ManjunathTech. This is probably a hardware failure at this point. I don't know if it's the battery, adapter or the system board.
  Although this does not exactly reflect your question, it should help you to troubleshoot and fine-tune the cause:
  Battery not power Notebook or hold a Charge

  If you want to check if it was a hardware failure, and the steps above are inconclusive, you can try a HP recovery:

  Performing a recovery of HP (Windows 8) system. If the recovery does not change the behavior, I recommend you to contact support.

  You can contact HP to see if your repair options:
  In North America, dial 800-474-6836 outside of North America to find your number of support here
  HP technical support

• After three years

  Hello, I am a user of a precarious Compaq CQ50 104NR (P/N: FE875UA) that I bought about 3 years ago. This laptop has been a boon to them for the past three years, especially in the first years of 1 and half of its use. However, I am now extremely upset by this product, because after only 3 years, it is no longer functional and all my attempts to get its software functions have been blocked by the problems compounding materials. Given the number of questions coming from my laptop, one might think that I took very poor care of her. Nothing could be further from the truth. Here is a list of the problems that have arisen in nearly a sequential i order that it took place.

  (1) the cord needed replacement because it Frays at the crossroads where he met the box (I don't know his exact name). This has happened despite meticulously wrapping so that this never folded junction.

  (2) the laptop heated at a rapid pace, allowing it to start cutting at the drop of a hat. I was told by a reputable sales and repair service who acted with the fan so I asked that to be fixed.

  (3) the screen would quickly up and down as if jumping or flicker. I don't know the cause of this and the research online, I came to the conclusion that it was with a cord or other losses coming.

  (4) the screen would spontaneously less bright and then clear up to its original luster. When this happens, the laptop would stall. I just thought it was simply because of the need to change the battery. However, a software problem later which lead me needs to recover my system son me the my last question.

  (5) when I tried to recover my laptop after having known one another 'blue screen of death"that left my laptop unable to exceed the faze of loading the boot sequence, I received a message telling me that he needed to be plugged in to AC power for this type of operation. This confuses me, because it was already plugged in to AC power. So find that strange, I took special note of the LED with the bolt of electricity above and I noticed that it was not light despite being connected.

  What I want to know is, what I do now, because this is obviously beyond the scope of all the repair of your free software based. I am very disappointed and upset this series of failures that happened in quick succession on the other. Can I change it? Can I get some kind of useful advice and long-term and/or support because as a student at the University, my life is very busy and hectic, and with the new semester on start in a few weeks, I need my laptop because it is an integral part of this hectic and busy lifestyle. I don't know if they are already gone, but I think I've lost a number of important documents and copy files such as notes and soft manuals. This is nto start talking about personal things like my email and music.

  So I'm practically begging here, please help, because it has left a bad taste in my mouth to what I thought, it was a very reliable brand.

  [number removed for privacy]

  Screen dimming is probably due to the inverter (less than $20 eBay).  The question of burden is probably the power supply.  The socket is shorted, broken pin or cold welding (even eBay probably less than $20).  The overheating problem will require new thermal paste of very good quality on the processor and the video chip. The problem is that you will probably have someone do it for you.  The price of labor could vary from a work time of three hours depending on the store.  Labour rate of $ 50 to $ 150 depending on the store area.  I guess that some countries that the United States may be much cheaper.  If you know people in the computer science program at the school, it can cost you nothing but a few large glasses of... Ah... glazed iced tea, the Yes!  Today, computers become faster and better very fast pace.  I will start to think twice before you approached $ 400 to repair and consider upgrade to a new machine.  Of course, it must be able to come up with the rest of the money.

• Satellite R850 - battery and the question of the burden

  I HAVE A TOSHIBA SATELLITE THAT I BOUGHT FROM AMAZON AND IS NOT GUARANTEED. COFFEE SPILLED ON IT WHILE I WAS DOING SOME WORK AND HE DIED.

  I LEFT DRY AND WHEN IT WAS LIT, HE WOULDN'T COME, I TOOK IT TO A STORE OF THE LOCAL COMPUTER WHERE IT WAS CLEANED AND TOLD ME TO GET A NEW BATTERY, BECAUSE THE BATTERY WAS BAD, SO I HAD A BATTERY ON EBAY.

  THIS TIME, THE PROBLEM WAS that HE CHARGE FOR a MINUTE AND THEN STOP TO LOAD. I DECIDED TO TRY THE BATTERY WITH THE LAPTOP AND FOUND SUPPORT FOR 2 MINUTES SAME AND OFF. THEN I CONCLUDED THAT THE PROBLEM WAS NOT THE BATTERY, BUT MAYBE THE MOTHERBOARD. BUT SINCE IT IS A NEW LAPTOP I WAS ADVISED TO JOIN THE TOSHIBA ONLINE FORUM, SO THAT I WILL BE DIRECTED TO WHERE THE PROBLEM WOULD BE SOLVED PERMANENTLY.

  PLEASE COULD ALL HELP. I WOULD BE VERY GRATEFUL...

  Thank you

  > BUT SINCE IT IS A NEW LAPTOP I WAS ADVISED TO JOIN THE TOSHIBA ONLINE FORUM, SO THAT I WILL BE DIRECTED TO WHERE THE PROBLEM WOULD BE SOLVED PERMANENTLY.

  What to say; the coffee spilled on the laptop and any fluid is not really good for an internal parts especially for the motherboard.

  I have no idea what part exactly damaged by spilled coffee, but it looks like a part of the motherboard is affected. Perhaps is the electronic power supply defective?

  I think that the laptop needs a verification and don t ask any technicians Nick fans because these guys just talk about possible problems.

  The device must be checked by a professional technician (service partner chartered Toshiba in your country) which has special tools and diagnostic software.

• ANALYSIS QUESTION - OFFICEJET PRO 8600 - ALL-IN-ONE

  I HAVE A HP OFFICEJET PRO 8600 PREMIUM E ALL IN ONE-N911N PRINTER.  I have
  HAS RECENTLY HAD SOME PROBLEMS WITH THE SOFTWARE/DRIVERS DESKTOP, WHERE THE
  SOFTWARE DOES NOT OPEN ON MY DESTOP.  I CONTACTED HP TECHNICAL SUPPORT. THEY
  TOOK CONTROL OF MY DESKTOP AND MY SOFTWARE HAS DETERMINED COULD HAVE BECOME
  CORUPTED AND SO DOWNLOADED FROM THE HP WEB SITE LATER
  THE OFFICEJET 8600/DRIVERS SOFTWARE VERSION, AND THAT SEEMED TO
  SOLVE MY PROBLEMS, UNTIL I DISCOVERED WHAT I BELIEVE, IT IS A BUG OR HAS
  SERVICE CAPACITY FORGOTTEN WHEN SCANNING BY USING THE MOST RECENT SCANNING
  SOFTWARE.   THE QUESTION IS, WHEN YOU USE THE 8600 DESKTOP SOFTWARE TO ANALYZE
  A DOCUMENT: IF I SCAN A FEW PAGES USING THE DOCUMENT FEEDER, THEN,.
  BEFORE I SAVE THE FILE, I WOULD LIKE TO ADD ANOTHER PAGE SCANNED, TO THIS
  SAME FILE, BUT YOU WANT TO ADD THIS EXTRA PAGE USING THE FLAT GLASS
  (NOT THE DOCUMENT FEEDER), THE SOFTWARE NOT ME LETS NOT DO THAT. THE
  SCANNING SOFTWARE IS ALWAYS LOOKING FOR THE PAGE EXTRA (S) TO BE
  ADDED, COMING THROUGH THE DOCUMENT FEEDER (SOFTWARE ONLY)
  RECOGNIZE ADDITIONAL PAGES TO COME FROM ANOTHER SOURCE, OTHER THAN
  FROM THE SAME SOURCE YOU STARTED SCANNING WITH). I'VE ALWAYS BEEN ABLE TO
  DO THIS WITH MY OLDER VERSION OF THE DESKTOP SOFTWARE (CD VERSION ONLY)
  CAME WITH MY PRODUCT), BUT SINCE I DOWNLOADED THE LATEST VERSION, IT
  DON'T ME LETS NOT START SCANNING OF A DOCUMENT FROM A SINGLE SOURCE (DOCUMENT
  FEEDER OR FLAT) AND ADD EXTRA FROM ANOTHER SOURCE () PAGES
  CHARGER DOCUMENTS OR FLAT).  IS THERE A BUG IN THE SOFTWARE?  TO
  SUMMARIZE THE PROBLEM: WHEN YOU START A SCAN USING THE DOCUMENT FEEDER.
  WANT TO ADD ANOTHER PAGE SCANNED ON THE GLASS FLAT, THEN
  SAVE ALL PAGES SCANNED IN A FILE?  YOU CAN'T DO THAT WITH THE MOST RECENT
  SOFTWARE (DOWNLOADED FROM HP WEBSITE), BUT YOU CAN THE MAKE WITH THE
  CD VERSION OVER OLD ONES. IS THIS FEATURE MISSING FROM MOST RECENT SOFTWARE?

  OK, the new SW to use can be found here:

  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi

  Download and install this.  This will install an application on your system, called "HP Scan" extended.   This software is designed to work with any recent HP scanner that has already installed the drivers.    The software does not replace your existing HP Scan supplied with the appliance.  It is rather an alternative which offers many more features than what came with your device originally.    This software is already available with the new HP machines.

  The selection of the default source is 'Use document feeder so burdened', so you should be able to scan from the ADF or flat all in one session.

  Enjoy!

• Questions about the implementation of clusters of storage and DTS on active cluster

  I have a few questions about the implementation of clusters of data store and SRS storage in VSphere 5.1.

  We have a data center with about 15 HP blades and a few servers non-lame.  The hosts are all either VSphere 5.0 or 5.1.  Our back-end storage is an EMC VNX 5700 with about 20 stores of data.  All the VMWare is managed by VCenter 5.1 running on a dedicated physical machine.

  Currently, each data store is used individually; No piles of data store are put in place.  When a new virtual machine is created, the administrator usually chooses the data with the most space store.  Periodically, we will go back and manually storage vMotion machines to balance the load.

  Recently, we have expanded the VNX storage, so we now have LUNS in different pools, with different levels of performance.

  What I would do is set up for the data store clusters, so that us when a virtual machine is created, the administrator must not know what data store is in which pool.  Also take advantage of the DRS storage so that the burden of storage will be "refine" himself a little.

  I know the setting up of a cluster of storage in a 'clean' environment is quite simple, but my concern is creation/conversion data warehouses existing in active production in the cluster, while they are used.

  If I access the screen "data warehouses and store data from clusters ', right-click on the data center and create a cluster, and then move the various data stores in the new cluster, will there be an interruption in the production running systems?

  I also wonder about activation of storage i/o control.  It is not currently enabled on data warehouses.  I know it's useful for the StorageDRS, but will be allowing any negative impact on the system?  If I turn on the warehouses of data, is there anything else I should do or set in addition to all that allows him?

  Finally, we are in the process of Site Recovery Manager configuration.  SRS has an impact on the configuration of the data clusters and DTS store?

  Thanks in advance for your comments.

  Mike O.

  Gregg Robertson wrote:

  Hello

  Clusters of data and using DTS store doesn't impact RS even if you create a cluster of data store for storage of replicated data and another for everyone else, this way you machines virtual you want to replicate are not moved on warehouses of data that are not replicated , but will still have the ability to move if there is a conflict.

  Gregg

  With all due respect but SRM and DTS don't go together. SRM does not at all support the use of DTS. So if you are configuring SRM forget DTS for now.

  Reason for this is that SRM knows no DTS and VMs can be in flight when a failover should occur, and bad things can happen. Also, the protection breaks when a virtual computer is moved between data warehouses in a cluster data store.

  In short: don't go there.

• See Transfer Server Questions

  I have a requirement to set up a forwarding server, and my question is, if the user data, such as My Documents are on back-end storage and redirected, when your desktop is extracted to the local computer, will be also removed user data. I don't think he will, because of the architecture of the product, as is check a new image. After the cut with the image, there should be access to data redeirected. When disconnecting from the local network, the redirected folders data will be always available on the image removed on the laptop? I'll test this, but wanted to know if anyone else has had this experience.

  Thank you

  Savoy 6

  If you need an offline office you should not redirect the user documents, etc.  Now, if you must, you can use offline folders and redirect their documents that you have visited.  But do so with caution as allowing it to all your virtual desktops would cause an enormous burden for your storage space.  This would increase the IOPS / s a little because she would try to cache all files offline for users of documents when opening session.

• Adding a RAID card to help speed up the export (and another question reader) in first Pro CC

  First of all, I read the Page Tweakers export section because that is my main concern is. First my questions, then the background and my current and proposed configurations:

  Question 1: Adding a hardware RAID controller, for example an LSI MegaRAID will sufficiently remove the burden of parity management CPU on my RAID 5 software that the CPU will jump of joy and export faster?

  Question 2: If true for above, then compare thoughts on adding smaller SSD for either a RAID 0 or less two RAID 0 volume volume complete HDD RAID 5. In other words, I think the purchase of four Samsung 850 Pro 128 GB SSD to put in a four disk volume to handle everything (projects/media, media, previews, export cache), or split it into two volumes of two disks of each and divide the tasks, or keep the idea of volume four disc and previews and exports on my drive HARD RAID 5 array.

  The 850 are valued at SEQ write: 550 / 470 MB/s so I could get around 2000 / 1500 MB/s read/write to a disk four RAID 0 or 1/2 who, if I divided in two volumes to minimize the volume of read/write at the same time, if it really matters with these SSD?

  The Tweaker page made some comments. A split is carried out the tasks between different drives, rather than a large effective RAID can really slow things down. Because SSDS are much faster than a single HARD disk, I think its more accurate than so I'm leaning towards the configuration of four discs put OS & programs on the C drive, media & projects on media on SSD (2 disks RAID 0) Cache and D (HDD RAID 5), file exchange & Previews & export on 2nd SSD RAID 0 (or combine the two RAID 0 and their functions).

  Just trying to get a point of view here, since I have not bought anything yet. Any experience/stories, I would be grateful.

  My current setup of training:

  My D drive is a software RAID 5 consisting of four 1 TB Western Digital RE4 (RED) 7200 RPM hard drives with CrystalDiskMark SEQ read/write of 339 / 252 MB/s.

  The C drive is 500 GB SSD (Samsung 840 (not Pro) and fact 531 / 330 MB/s.) My OS, Program Files and Page file are on C and media data/files/projects, etc. that are all about the RAID drive.

  Problem:

  Current configuration allows for smooth installation, just export seems slow, usually taking between two and two and a half times the video length to export. Thus, a 10 minute video takes 20-30 minutes for export. 15 minute video can take 30-40 minutes to export. The first 10% of the export of re-encoding takes less than a minute (seems fast), but it becomes slower when the final 10 or 20 percent may hang for several minutes as my system is running out of steam. So, where's the waste?

  I activated the hardware acceleration (because the GPU hack my GPU is not listed) and it can break through to 25% use a few times and eat up to 600 MB of VRAM (I have 2 GB of VRAM), otherwise it is slowed down export set. The CPU can boost at 50%, but it seems either too busy.

  Our calendar is simple with two video and two audio streams (a little music and especially the voices), with simple transitions (jump cuts or cross dissolves). Sometimes, we fast correct color, so that could use the GPU? Also, given that we are filming in 1080 P 60 p and 1080 export 29.97 FPS, I think who is scaling and using the GPU. I know that without the GPU, it takes much longer. I excluded buy a faster GPU because it doesn't seem to be breaking a sweat. I just need to know if my system is a bottleneck at the level of the disk hard because I am using software RAID and my disks are slow and hardware RAID will considerably reduce the processor load so it can export more quickly.

  Our files are not huge in nature. Most of our clips are several MBs each. Total files in the project are between 5 GB and 10 GB for each video with Windows Media File export being 500 MB to 1.2 GB on average. Look using Panasonic Camcorders, so the original files are AVCHD, I think (.) MTS files?).

  Considerations:

  1. I think to buy (and future proofing) a LSI Logic MegaRAID 9361-8i is 12 Gb/s SAS and SATA (because some SSD current can exceed the standard 6 Gbps).

  2. I will not replace my current HDD RAID 5 as not in my budget to spend 6 or more large SSD. These discs are more important to me for temporary storage because I delete files saved once. I don't mind a few smaller SSD inexpensive if they can make a significant difference for editing and export.

  I can only guess my RAID HDD is slow but the CPU is burdened by parity. I guess running RAID 10 would not really help.

  My configuration:

  my configuration:

  CPU - CPU i7 - 3930K @4.5 GHz

  RAM - G.SKILL Ripjaws Z Series 32 GB (4 x 8 GB) DDR3 2133 @2000

  Motherboard - ASUS P9X79 WS LGA 2011

  GPU - Gigabyte GeForce GTX 660 OC 2 GB (performed the hack of compatibility list to activate hardware acceleration).

  Drive C - 500 GB Samsung SSD (programs and Windows 7 Pro 64-bit) 840.

  D drive - four 1 TB WD RE4 enterprise hard drives 7200 rpm in RAID 5 software

  Box - Cooler Master HAF X

  CPU fan - Cooler Master Hyper 212 EVO with 120 mm fan

  Power - series Pro Corsair AX 850 watts 80 Plus Gold

  Optical drive - Pioneer BDR - 208DBK

  Thanks in advance,

  Eric

  OK, after overload of information on everything I tried (free), which might be my answer here. I went from codecs to export. When you use Windows Media File, Premiere Pro seems chugging along much slower than when you use the h.264 (not h.264 Blu - Ray). I don't know if it's because Microsoft has found a way to break it or what. But I'm the CPU usage of 70-85% on the 2 Pass of 2 as well as the use of the memory of 40% (or 12 GB). It exported in 14 minutes. Woo - hoo. I then did a similar test using Windows Media File. It took 31 minutes to export. The CPU has spent much of his time in the 30%, especially down in the 1930s mid-1940s with spike for memory usage was only 24% to 35% and 50%. Since then, I've read how h.264 codec is 'plu' for online files. It compresses better with less compression artifacts. He seems better, etc. Well, they both seemed on the same thing for me. I play both on my TV 70 "before I could comment further. In the future, I will consider a RAID controller and upgrade the HDDs to SSDS.

• Question of SCT TEMP space means that kinds fail?

  DB version: 11.2
  Operating system: Solaris 10
  
  We have a DB OLTP. These days, we regularly get
  

  ORA-1652: unable to extend temp segment by 128 in tablespace TEMP

  on our alerts log. About 7 to 8 times per hour.
  
  TEMP tablespace size is 21 GB and it has 0 MB freespace for several days. So far end-users of application will have no high no concerns.
  
  Question1.
  This means that none of their SQLs requiring a sort have failed? Or did they not only noticed in their newspapers?
  
  
  
  Question2.
  If ORA-1652 meant SQLs application fails, what I can do to release the temp tablespace?
  
  To diagnose why SMON is not clear the temp tablespace, I went through the note of ML
  + Temporary segments are not désallouées after a sort [ID 1039341.6] +.
  
  SEGMENT_TYPE of my temp tablespace is not TEMPORARY. It is not permanent either.
  
  
  Info on this Temp tablespace:
  
  
  
  

  SQL> select owner,segment_type from dba_segments where segment_type='TEMPORARY';
  
  no rows selected
  
  SQL> SELECT TABLESPACE_NAME, CONTENTS FROM DBA_TABLESPACES WHERE TABLESPACE_NAME='TEMP';
  
  TABLESPACE_NAME                CONTENTS
  ------------------------------ ---------
  TEMP                           TEMPORARY
  
  SQL> select OWNER,
         SEGMENT_NAME,
         SEGMENT_TYPE ,
         TABLESPACE_NAME
        from DBA_SEGMENTS
        where SEGMENT_TYPE = 'TEMPORARY';
  
    2    3    4    5    6  
  no rows selected
  
  SQL> SQL> select OWNER,
         SEGMENT_NAME,
         SEGMENT_TYPE ,
         TABLESPACE_NAME
        from DBA_SEGMENTS
        where SEGMENT_TYPE = 'PERMANANT';    
  
  no rows selected

  Max, to add to what has already been postponed Yes the error message means that one or more of the tasks requiring temporary tablespace failed. The question you need to ask is why? Your tablespace sorting could be set too small to cope with the workload or your system might suffer from an excessive burden for the space of sort. The temporary tablespace is used to support including stopped sorting by, select distinct, union, operations and also it hold temporary tables and hash area overflows to disk.

  Bad SQL plans may resort to excessive use of the temp.

  AdHoc queries via report ofter tools extract excessive amounts of data well beyond what the end-user needs and can indeed treat until the user launches a new version of the report.

  Sometimes a little tuning can drastically reduce the demand for temp.

  HTH - Mark D Powell.

• A question unanswerable datagrid?

  Hello

  I googled my question, observed that BURDENS of others as you are looking for the same answer... yet none of them are ever meet, but I'll stay hopefull...

  Flash CS4 with actionscript 3... How you fill a datagrid with a combobox cell?

  Can someone PLEAAAAAASE provide me the actionscrip for this seemingly impossible task?

  Thank you in advance!

  Hey SaneDevil,.

  I understand what you're trying to create. Something like a report generation tool or a tool of data collection.

  No, there is no way where the values of a CB can be directly filled in a DG atleast in Flash CS4.

  If you are familiar with Flex, I think you might have predefined models for what you are trying to reach.

  Flex to create more collection of such data and the data related to the user interface. Flash is used more animation and other purposes.

  Then try and take a look at one of the models of flex, for all that you know maybe there might already be a model for what you need.

  Hope this post helps you to create what you need

  See you soon!

• iOS 10 people record problem/question

  Hello

  I have a couple of "faces" in the issue of people who are coming in white, but acknowledged same 'face' of many times.  Is anyway to update it for photo comes actually?  At a few faces, I don't know that facial recognition found since it is coming from white.

  Hi JohnP007,

  Congratulations on your iPhone 7 more running iOS 10! I understand that some of your faces in the album of people pull up as a draft and you want to refresh. You can try to use the steps below to fix the faces on the thumbnails in albums.
  

  Difficulty faces and names mixed-up

  If you notice that there is a photo of someone in a collection that is poorly identified, you can remove it.

  1. Tap the person you want to remove in the album of people > select.
  2. Type Show done face to emphasize his face in every photo.
  3. Press on each photo that is not the person.
  4. Type > not this person.

  Hide people

  You can hide the people or groups that you don't want in your album of people.

  1. Open the album people and press Select.
  2. Touch the people you don't want to see.
  3. Click Hide.

  If you want to see the people that you have hidden, press on show hidden people.

  People in the Photos on your iPhone, iPad or iPod touch

  This should be corrected without delay faces. Please use the Apple Support communities to post your question. Good day.