Question of L2TP with ASA

HI.i want to connect from xp client PIX via L2TP IPsec connection, but I cant.this is my network.

PIX:

outside = 15.15.15.1/24

inside = 10.10.10.1/24

XP = 15.15.15.2 (connected to the AAS outside interface) client

PIX config:

!!!!!!!!

PIX Version 7.2 (3)

pixfirewall hostname

activate the password xxx

names of

interface Ethernet0

nameif outside

security-level 0

IP address 15.x.x.1 255.255.255.0

interface Ethernet1

nameif inside

security-level 100

IP 10.10.10.1 255.255.255.0

interface Ethernet2

Shutdown

No nameif

no level of security

no ip address

interface Ethernet3

Shutdown

No nameif

no level of security

no ip address

interface Ethernet4

Shutdown

No nameif

no level of security

no ip address

passwd xxx

passive FTP mode

TR1 extended access list ip 10.10.10.0 allow 255.255.255.0 17.17.17.0 255.255.

55.0

TR2 extended access list ip 10.10.10.0 allow 255.255.255.0 17.17.17.0 255.255.

55.0

list of access allowed extended l2tp udp any any eq 1701

pager lines 24

Outside 1500 MTU

Within 1500 MTU

17.17.17.2 - 17.17.17.10 vpn IP local pool

no failover

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

NAT (inside) 0-list of access tr1

group-access l2tp in external interface

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout, uauth 0:05:00 absolute

Enable http server

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-3des esp-md5-hmac ipsec

Crypto ipsec dy 1 transform-set dynamic-map

crypto card cry 1-isakmp ipsec dynamic dy

out cry crypto map interface

crypto isakmp identity address

crypto ISAKMP allow outside

crypto ISAKMP policy 1

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

Sevan strategy of Group internal

attributes of sevan group policy

Protocol-tunnel-VPN l2tp ipsec

Sevan username password xxx

sevan username attributes

Protocol-tunnel-VPN l2tp ipsec

sevan tunnel-group type ipsec-ra

tunnel-group sevan General attributes

vpn address pool

Group Policy - by default-sevan

Sevan tunnel ipsec-attributes group

pre-shared-key *.

Sevan tunnel-group ppp-attributes

No chap authentication

ms-chap-v2 authentication

context of prompt hostname

Cryptochecksum:xxx

: end

in the client Xp I configured the vpn connection correctly according to the examples I found in the Cisco documents.

When I try to connect from xp client nothing happens I turn on debugging and I get this error:

Oct 07 12:04:51 [IKEv1]: group = 15.15.15.2, IP = 15.15.15.2, cannot

find a group valid tunnel, abandonment...!

Oct 07 12:04:51 [IKEv1]: = 15.15.15.2, IP = 15.15.15.2, peer group of withdrawal of

table peer has failed, no match!

Oct 07 12:04:51 [IKEv1]: group = 15.15.15.2, IP = 15.15.15.2, error: unable to r

eMove PeerTblEntry

Oct 07 12:04:52 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

support useful ext = 4)

Oct 07 12:04:54 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

support useful ext = 4)

Oct 07 12:04:58 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

support useful ext = 4)

Oct 07 12:05:06 [IKEv1]: IP = 15.15.15.2, invalid header, lack of payload SA! (n

support useful ext = 4)

Please help me find the problem! Thank you

I recommend something similar. But instead to "no protocol-tunnel-vpn l2tp-ipsec", you can also place the order

"vpn-tunnel-Protocol l2tp ipsec" in the DefaultRAGroup tunnel-group concerned both group policy. Just make sure you don't violate one of your other VPN. See this for more details:

http://www.securityie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=10;t=001767

Concerning

Farrukh

Tags: Cisco Security

Similar Questions

QOS with ASA - corresponding to questions of packages

I have a few questions of mote of ASA and QOS - level code 8.2.5

Let's say I have the following...

TG-NonVoice class-map

corresponds to the tg-traffic-acl access list

class-map-traffic TCP

corresponds to the tcp-traffic-acl access list

class-map voice-TG

match dscp ef

match tunnel-group x.x.x.x

How to know the hierarchy of what the ASA uses to match a package? Since a package can only correspond to a class-map, I created the access list to refuse statements to ensure that the packet matches what I want. Example - tcp-traffic-acl access list, I didn't include the traffic tunnel so I denied the traffic of the tunnel at the beginning of the access list. This is the correct procedure given that I did not know what order the ASA aligns packages to my access to my class-maps lists. Y at - it an order? TG-voice has priority in the plan of the policy is it automatically get used to match first?

Second example:

Let's say I

TG-NonVoice class-map

match flow ip destination-address

match tunnel-group x.x.x.x

class-map-traffic TCP

corresponds to the tcp-traffic-acl access list

class-map voice-TG

match dscp ef

match tunnel-group x.x.x.x

Here I have only an access list. How know if order used to filter packets? If I don't want the tcp-traffic-acl include NOT packages that could possibly correspond in the VPN tunnel that I put a refusal at the beginning of the list of access for VPN traffic to be sure? What would be the rate used by the ASA to determine if a packet matches a rule of class-card for a package would correspond to multiples, but from what I've read, that it does not get included in other once it corresponds to the first match. Understand?

Thank you

Hello

I think that this price covers everything

This is the best document I found on the web about the MPF.

To take a reading

http://blog.INE.com/2009/04/19/understanding-modular-policy-framework/

Note all useful posts!

Kind regards

Jcarvaja

Follow me on http://laguiadelnetworking.com

NAC Appliance with ASA (for remote user VPN)

I have a pair of firewall 5520 cisco which is used as a VPN gateway (for remote user VPN) and perimeter firewall Internet (to provide outbound internet connectivity).

We allow the NAC to remote VPN users. I have it will be deployed with active 3 layer inband.

The problem with this design is that how to ensure that outgoing internet traffic does not pass through the CASE?

I heard about couple of optioins:

-ACB (for send only IP subnet to VPN users remote to go through CASE)

-Version 8.x characteristic of ASA (Restrcit access to VLAN under Group Policy).

I intend to do with ASA firewall where I can set a new subinterface on the SAA (with a new tag VLAN) and under the group policy for remote user VPN, I select the option to "restrict access to the new VLAN.

My question is: is - it still works (even if the firewall have a route to the internal network by using the 'inside' interface and NOT the new interface of the NAC). If this does not work, please let me know what are the other options for this type of deployment.

Thanks in advance.

Hello

It should work. Please see the attached PDF for more clarity on this topic: https://supportforums.cisco.com/docs/DOC-9102

HTH,

Faisal

Remote access VPN with ASA 5510 by using the DHCP server

Hello

Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?

I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:

!

ASA Version 8.2 (5)

!

interface Ethernet0/1

nameif inside

security-level 100

IP 10.6.0.12 255.255.254.0

!

IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)

!

Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1

!

Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto-map dynamic dyn1 1jeu transform-set FirstSet

dynamic mymap 1 dyn1 ipsec-isakmp crypto map

mymap map crypto inside interface

crypto ISAKMP allow inside

crypto ISAKMP policy 1

preshared authentication

3des encryption

sha hash

Group 2

life 43200

!

VPN-addr-assign aaa

VPN-addr-assign dhcp

!

internal group testgroup strategy

testgroup group policy attributes

DHCP-network-scope 10.6.192.1

enable IPSec-udp

IPSec-udp-port 10000

!

username testlay password * encrypted

!

tunnel-group testgroup type remote access

tunnel-group testgroup General attributes

strategy-group-by default testgroup

DHCP-server 10.6.20.3

testgroup group tunnel ipsec-attributes

pre-shared key *.

!

I got following output when I test connect to the ASA with Cisco VPN client 5.0

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO

4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: Group = testgroup, I

[OK]

KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable

Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes

Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!

Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address

Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048) , : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740) , : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

Kind regards

Lay

For the RADIUS, you need a definition of server-aaa:

Protocol AAA - NPS RADIUS server RADIUS

AAA-server RADIUS NPS (inside) host 10.10.18.12

key *.

authentication port 1812

accounting-port 1813

and tell your tunnel-group for this server:

General-attributes of VPN Tunnel-group

Group-NPS LOCAL RADIUS authentication server

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

No Internet connectivity with ASA 5505 VPN remote access

Hello

I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?

Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.

Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?

I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.

Thank you very much for you help.

Concerning

Salman

Salman

What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.

You have at least 2 options:

-You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.

-You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command

permit same-security-traffic intra-interface

HTH

Rick

Question/design architecture with best practices?
Question/design architecture with best practices?

Should I have separate Web server, weblogic application and IAM?
If yes that how this time will communicate, for example can I webgate on the server that will communicate to each other?
Any reference to decide how to design and if I have weblogic separate one for enforcement and one for IAM that how session management will take place etc.

How is general design happens IAM project?

Help appreciated.
I have a business web application deployed on weblogic1 and OHS1

deploy webtier on this OHS1 to protect the resources on OHS1. webtier will be recorded at OAM (where will be able to communicate with OAM)

I also IAM deployed on weblogic2 & OHS2

IAM components have weblogic. then ok. But you don't need to ohs2 here, unless your application itself requires OHS for hosting. But here, you mention that it is fair to IAM - so no need to OSH here. IAM installing requires weblogic.

wanted to know where should I create provider (weblogic1 or weblogic2), and install webgate (OHS1 or OHS2 or both)?

I hope it is clear now. If this isn't the case, query post for what is not clear.

Question about Threads with WHILE and FOR

Hi all

I have a question on threads with a loop on this topic sentece.

Have the following class:

class test{

bool foundThing;
PararellSearch(string [] lista, string s2find){
while(!foundThing)
{
for(int i=0;i<lista.length;i++){
if(s2find==lista){

foundThing = true;

break;

}

}

}

}
If I start 10 threads which are using the PararellSearch method to look into lista, each of them inits into a different point, and when some of them found the right word then set foundThing= true. It will stop WHILE and FOR loop in all the threads? 
If not, how could I do it?

Thanks a lot for your help.
David.

Edited by: user13553506 on 27-dic-2010 12:15

Edited by: user13553506 on 27-dic-2010 15:54                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    
			 When you post the code, you'll want to post a [url http://sscce.org] NBS so that it is clear that what you try to do it. For example:
1. in the validation of code, put {code} before and after him, then he will be readable.
2. the convention in Java must start with a capital letter class names, so test, could not test.
3. the convention in Java is to start with lowercase letters, so parallelSearch, not PWhateverMisspellingYouHaveThere method names.
4. There is no such thing as bool. It is a Boolean.
5. it is a String, not string.
6. never use == to compare the States of objects (such as the content of the strings). Use equals().
To answer your question: If you create Test 10 objects, then, given that foundThing is an instance variable, there will be 10 variables entirely independent foundThing. An adjustment will not affect the other. In this case, the easiest thing to do would be to foundThing static, so that there is only one copy which is shared by the Test class as a whole. This isn't the only way, or even the best way in all cases, but you have enough other problems to face, so for now to keep things simple.
Finally, when you have a variable that is shared by multiple threads, you need to either make all the access to this variable synchronized on the same lock (reads and writes), or you need to declare the volatile variable.

 
            
            
		     new here... question to start with 
			 Hello world...
New to the forum and glad to hear things with Dreamweaver.
A question to start with... How does a program Dreamweaver so that it automatically reformatted in different browsers (sizes).  Is it still possible?
Cheers...
Twingi
			 How does a program Dreamweaver so that it automatically reformatted in different browsers (sizes).  Is it still possible?
It is certainly possible.  Tell us what you mean by 'formatting automatically' and we will tell you how to do it.
		    
            
            
		     Question of AnyConnect with Cisco ASA 5505 
			 I keep hitting my head against the wall on this one. Whenever I try to connect to the AnyConnect SSL VPN I get the following error
"No address available for an SVC connection.
Up and down, I checked that my VPN pool be present and assigned. I have removed/re-added it so many times. I use the SMDA to implement through the wizard. Any help please?
Here is my config
http://pastebin.com/ABvSpzUq
			 It seems that you are falling into default group policy.  You must activate the tunnel-group-list under the webvpn that allows users to select the group to which they connect, or set the attributes of the user to force the user into the correct connection profile...
activation of tunnel-group-list
WebVPN
tunnel-group-list activate
Configuration of the user attributes:
Chris mXB.dKavHoEa0gaC of encrypted password username
username Chris attributes
VPN-group-policy HBNS_AnyConnect
value of group-lock HBNS_AnyConnect
type of remote access service
--
Please do not forget to choose a good response and the rate
		    
            
            
		     Cisco Firepower 4110 Clustering with ASA and DFT 
			 Hi all
We have a pair of Cisco 4110 firepower devices and have them clustered for the ASA Security Module.
There seems to be no option to add an additional logical device for the threat of fire power defence Module, so can only assume this is not supported in an active/active state.
More on the SAA Module there is no tab of remote access VPN Configuration.
So my question is how to incorporate the functionality of defense threat in the ASA, I suppose that this would be by the engine unloading in the advanced settings, but requires the SAA be in Active mode / standby and the power of fire threat defense logical device will be available?
Second question is it would have been better buy the Cisco ASA 5585 X with the Module of firepower in support of all the regular features of the SAA as well as traffic inspection unloading to the module of firepower?
I found some documentation on the Cisco site, but tend to lose sight of where the reference to FTD and not be supported of the Clustering or RAS VPN not supported by ASA or FXOS docs, so I was hoping for some insight on here.
Appreciate any clarity around the support of devices 4110 of the firepower and configuration of the FTD and ASA combines the features supported.
We run ASA v9.6 (2) and FXOS 2.0.1 (86).
Thanks in advance.
Mark
			 On a firepower 4100 Series chassis, you can run a single logical unit. Several logical devices are supported only on the 9300 firepower that supports up to 3 modules of security.
So choosing between types of module ASA and DFT (or technically you can also deploy the RADware vDefense Pro but it is mainly for service providers).
One or the other and never the two.
The module of the SAA supports remote access VPN over 4110 of firepower. I put one in place personally nothing this month. Have you recorded the chassis with the smart licence and applied ASA licenses (basic an and 3DES / AES)?
The ASA modules take supported the HA and inter-chassis clustering on the 4100 series hardware.
If you run picture FTD, there is currently no support for remote access VPN. It is a high priority position of roadmap for a future version (post - 6.2). FTD does not currently support the chassis inter cluster but that should be in version 6.2.
		    
            
            
		     AnyConnect 4.0 license with ASA-5515-FPWR 
			 Hi all
I have a small question, where I can't find a clear answer for:
A customer wants to buy a new ASA for a showroom. He wants to connect 30 phones VPN and 60 VPN users, where only 10 of them are simultaneously connected. Then we would have two choices now
-Either go with the 3.5 Anyconnect licensing, with a premium SSL 50 license and activation phones VPN and mobility AC licenses
- Or go to AC 4.0 license, where we would have to license 100 users with MORE licenses.
My questions are:
-Can I any other / more license on the SAA (i.e. SSL)
-Where to install the license
-How is the number of users (i.e. of the ad groups, local accounts)
Is there a documentation clearly indicating the answers
Thank you all for your help.
			 If you want that the phone itself to be the endpoint remote VPN access, then Yes - you need VPN phone license which requires in turn AnyConnect Premium (for 3.x installations)
"Plus" AnyConnect (for 4.x) includes 'VPN functionality for PC and mobile platforms, including per-app VPN on mobile platforms and phone Cisco VPN' (referring to the January 2015 of the ordering Guide AnyConnect 4.0 version)
		    
            
            
		     Problem with ASA 5505 VPN remote access 
			 After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?
Here is the cfg running of the ASA
----------------------------------------------------------------------------------------
: Saved
:
ASA Version 8.4 (1)
!
hostname NCHCO
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
network of the NCHCO object
Subnet 192.168.2.0 255.255.255.0
network object obj - 192.168.1.0
subnet 192.168.1.0 255.255.255.0
network object obj - 192.168.2.64
subnet 192.168.2.64 255.255.255.224
network object obj - 0.0.0.0
subnet 0.0.0.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the Web server object network
the FINX object network
Home 192.168.2.11
rdp service object
source between 1-65535 destination eq 3389 tcp service
Rdp description
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0
inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224
outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
LAN_Access list standard access allowed 192.168.2.0 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
outside_access_in list extended access permit tcp any object FINX eq 3389
outside_access_in_1 list extended access allowed object rdp any object FINX
pager lines 24
Enable logging

asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 649.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0
NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64

NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
the FINX object network
NAT (inside, outside) interface static service tcp 3389 3389
Access-group outside_access_in_1 in interface outside
Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http *. **. ***. 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform
IKEv1 crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map

dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0

dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHCO group policy
NCHCO group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1
value by default-field NCHCO.local
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username NCHvpn99 password dhn. JzttvRmMbHsP encrypted
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
IKEv1 pre-shared-key *.
type tunnel-group NCHCO remote access
attributes global-tunnel-group NCHCO
address pool VPN_Pool
Group Policy - by default-NCHCO
IPSec-attributes tunnel-group NCHCO
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
ASDM image disk0: / asdm - 649.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
---------------------------------------------------------------------------------------------------------------
And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:
---------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7601 Service Pack 1
Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026
Try to find a certificate using hash Serial.

2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027
Found a certificate using hash Serial.
3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011
RELOADED successfully certificates in all certificate stores.
4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002
Start the login process
5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is NOT behind a NAT device
21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1.  1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017
xAuth application returned

27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1.  1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F
SPLIT_NET #1
= 192.168.2.0 subnet
mask = 255.255.255.0
Protocol = 0
SRC port = 0
port dest = 0
45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local
46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710
47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11
49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now
57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">
59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify is set to 28800 seconds
60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***

61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059
IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)
62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025
OUTGOING ESP SPI support: 0xAAAF4C1C
63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026
Charges INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001
Launch VAInst64 for controlling IPSec virtual card
66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034
The virtual card has been activated:
IP=192.168.2.70/255.255.255.0
DNS = 192.168.2.1, 8.8.8.8
WINS = 0.0.0.0 0.0.0.0
Domain = NCHCO.local
Split = DNS names
67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038
Were saved successfully road to file changes.
69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261

192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036
The routing table has been updated for the virtual card

71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A
A secure connection established
72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 96.11.251.149.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 192.168.2.70.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001
Did not find the smart card to watch for removal
75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0x1c4cafaa in the list of keys
78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0xc5bfbe3e in the list of keys
80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F
Assigned WILL interface private addr 192.168.2.70
81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037
Configure the public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046
Define indicator tunnel set up in the registry to 1.
83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205276
85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276
88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019
Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205277
91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277
94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205278
96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***
97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278
---------------------------------------------------------------------------------------------------------------
Any help would be appreciated, thanks!
			 try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.
		    
            
            
		     a way vpn with asa to the 800 router 
			 people
I have a site to site vpn set up between a asa 5540 and a 800 router
I want only the vpn to be initiated from the asa with the 800 remote listen incoming connections
I know that I can define the type of connection on the asa as only come but I can find an equivalent command to answer only for the 800 remote
can anyone point me in the right direction or is it enough to simply configure the asa as are created only for this encryption card
Thanks to anyone who takes the time to answer
			 Hello
I recommend you configure the tunnel as a dynamic to static tunnel VPN, the ASA will be the static counterpart, so it will be the initiator and the router will never be able to establish the connection.
The ASA will be a common L2L configuration, but the router will use a dynamic encryption card.
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a008051a69a.shtml
The PIX in the example is old, then you can simply adjust the controls to your current version, the important thing is to understand the concept.
Please let me know if that answers your question,
Thank you.
		    
            
            
		     Question - the upgrade with 3 USB card and esata 
			 I have an early 2008 Mac Pro Quad core 2.67 going to have maxed out RAM soon and are planning to get a couple of 2 TB seagates Macgurus. I'm a little embarrassed by my lack of knowledge, but I'll put my questions over there anyway. Last year, I bought a 120 GB ssd card Accelsior PCIe mercury OWC - not being aware of the s and outs of things, but I knew it wasn't a port multiplier with two external esata ports. so my question is this: since I have to live with this card can I connect the esata ports to discs in separate outdoor pens and then through disk utility make a raid 0 set, and what size of disc must be effective for the cost the least?  I intend to get a USB 3.0 also so that I can use this speed also.  My other plans must be a drive of fusion with the ssd 120 on the map of Accelsior with a disk of 1td existing in my drive for the system Bay and replace all small readers of seagate more big HARD drive and I'm wondering if the 2 TB is the largest capacity I can use internally. I am on a very limited budget so that's the reason why I'm thinking hdd and if there is someone with advice on a card USB 3 I would appreciate your comments - in fact, I would be happy to comment on everything I mentioned, I'm a little out of the loop on the evolution in recent years. It is possible to configure a raid with two disks of two PPI crd esata ports would there be an advantage with drives of 2 TB or 1 TB disks would work as well for raid 0. Do I intend to put in storage for Time Machine with the USB 3 map, and what size disc would be appropriate for Time Machine? I'm not lazy and waiting for someone to find out - I did weeks of research to get to this point and I just need a little advice. I'm just going through what I know and what I can afford, but maybe I'm missing another solution to try to get a little more speed and back up storage for my photoshop files.
I do only cc2015 Photoshop, Lightroom and On1software version 10.1 using OS X El Capitan and a cg 276 Eizo monitors more a second older Eizo. My usb ports 2 are all used and I rarely use a firewire port. Thanks in advance to all those who have advice. This is the first time that I have not posted anything on this forum
			 Time machine is a USB 2 connection. No real reason for a USB 3 connection.
There is no RAID in disk utility in El Capitan. Apple dropped the disc utility in El Capitan. However, you can still the Terminal commands to configure RAID.
https://www.reddit.com/r/OSX/comments/3d7aw2/does_el_capitan_disk_utility_suppor t_raid.
You should be able to create a set with eSata RAID
Here is a map of the BSE 3 compatible with El Capitan.
http://www.sonnettech.com/product/allegrousb3pcie4port.html
USB 3.0 Mac Pro 2008 El Capitan
Make sure that the card said it works with El Capitan. Some cards USB 3 is no longer with El Capitan as the CalDiget of first generation card.
Internally the Mac can also use large HD depending on availability. However, there is a bug that first appeared in 10.8.4 and has not yet been set. To format a plu 2.2 to internal HD:
-Use a disk utility of all Mac OS X older, including the 10.6 DVD (if your Mac can boot from it) or any of the installation DVD player or boost saved work.
-Another solution is to move this drive in an external case and delete it there (assuming your case is modern enough to deal with readers more than 2.2 to.
In addition,
To sled mounting internal:

The penetration of the screw depth for 'down-screw mount adjacent to the platters' on some readers from over 3 TB have been shortened. This may mean that the live sled down until they adjust and begin to compress the washers on the sled. If this is the case, your drive will not rest flat on the sled and do not breed with the connector backplane without additional adjustment.
		    
            
            
		     want to 15 t k100 CT0: Question for compatibility with cards Envy 15 - update of the original wireless 
			 Hi, first of all thank you for the research this post ~!
I got a craving for my friend last year, and this model use an old card wireless (Atheros AR9485) that is not supported bandwidth of 5G. I'm looking for a replacement that could support 2.4 and 5 G band.
Model (based on the identification of auto for the HP Web site):
Envy15t CT0 k100
Model: G0T59AV
Series: [personal information]
Some positions, said there will be compatiablity question if I buy a card at random, so could someone help me with this? Maybe give me a model which can be integrated in this situation?
HP partsurfer web page below, based on the model of my machine, I found some info, but really not sure whether this is the right one.
http://PartSurfer.HP.com/search.aspx?SearchText=G0T59AV

Thank you again to finish reading my problem! THX!
			 Hello
From my research, no whitelist more for new HP laptops (manufactured after 2014). Sounds like your machine has only 1 antenna so you can use the second one on the list.
Kind regards.

 
		 
          Maybe you are looking for 
           
            
		     How to provide a botton that takes a quick measure of the Isc and VOC? 
			 Right now I have a program that allows to measure Voc, Isc and the efficiency of the solar cell. How to provide a botton that takes a quick measure of the Isc and VOC and displays the result next the botton? I want to do this because I want to know V 
		    
            
		     How can I get a password for my wi - fi? 
			 I can't find my wifi password. I'm with Verizon Wireless network. I tried asking them for her, but I just get a race. When I renewed my contract last year they sent me a free «ellipsis7 Tablet» I asked on the Wi - Fi, and they said it was included. W 
		    
            
		     Help error message 
			 I tried installing an update of Windows, said that it is important, but cannot install it. Always come back with code 643 Windows has encountered an error. How can I fix it?  I can ' t download itunes says I'm in safe mode (which I checked, and I'm n 
		    
            
		     screen display problem? 
			 my screen has a box in the upper left corner, more brilliant than the rest of the screen.  Troubleshooting unresponsive. Help, please 
		    
            
		     SD reader does not 
			 I have a laptop ACER Aspire 5735-4474.  I was always able to load pictures from my SD cards. Now computer laptop does not yet see the card when I plug. What's wrong?